Sorção e lixiviação de tiametoxam em solos tratados com lodo de esgoto e cultivados com cafeeiro

The objective of this study was to evaluate the sorption and leaching of thiamethoxam in dystrophic Red-Yellow Latosol (LVAd), dystroferric Red Latosol (LVdf) and Red-Yellow Argisol (PVAd) with coffee under the effect of sewage sludge doses. There was thiamethoxam sorption decreasing at higher doses of sewage sludge in LVAd and LVdf. In the PVAd, sorption was higher in samples that received the highest dose of sewage sludge. At 150 days after the application of thiamethoxam, the compound began to be detected in the effluent, in all soils. Dissolved organic carbon had no influence on the thiamethoxam leaching.

Coeficiente de distribuição do inseticida tiametoxam na fração mineral de solos sob efeito de ácidos orgânicos mono, di e tricarboxílicos

The aim of this study was to investigate the sorption and desorption of thiamethoxam in contrasting soils under the effect of organic acids. The results showed that MTo sorption had higher Kd. The presence of organic acids increased sorption and reduced desorption of thiamethoxam at MTo. The opposite was observed for the LVdf where the presence of 400 µmol L-1 of acid reduced the sorption of thiamethoxam in a concentration of 20 µmol L-1, not influencing desorption. The dynamics of organic acids with minerals from the soil particles were clarified by infrared analysis.

Regioselective modification of galactose-containing polysaccharides in aqueous media

Biorefining is defined as sustainable conversion of biomass into marketable products and energy. Forests cover almost one third of earth’s land area, and account for approximately 40% of the total annual biomass production. In forest biorefining, the wood components are, in addition to the traditional paper and board products, converted into chemicals and biofuels. The major components in wood are cellulose, hemicelluloses, and lignin. The main hemicellulose in softwoods, which are of interest especially for the Nordic forest industry, is O-acetyl galactoglucomannan (GGM). GGM can be isolated in industrial scale from the waste waters of the mechanical pulping process, but is not yet today industrially utilized. In order to attain desired properties of GGM for specific end-uses, chemical and enzymatic modifications can be performed. Regioselective modifications of GGM, and other galactose-containing polysaccharides were done by oxidations, and by combining oxidations with subsequent derivatizations of the formed carbonyl or carboxyl groups. Two different pathways were investigated: activation of the C-6 positions in different sugar units by TEMPO-mediated oxidation, and activation of C-6 position in only galactose-units by oxidation catalyzed by the enzyme galactose oxidase. The activated sites were further selectively derivatized; TEMPO-oxidized GGM by a carbodiimide-mediated reaction forming amides, and GO-oxidized GGM by indium-mediated allylation introducing double or triple bonds to the molecule. In order to better understand the reaction, and to develop a MALDI-TOF-MS method for characterization of regioselectively allylated GGM, α-D-galactopyranoside and raffinose were used as model compounds. All reactions were done in aqueous media. To investigate the applicability of the modified polysaccharides for, e.g., cellulose surface functionalization, their sorption onto pulp fibres was studied. Carboxylation affects the sorption tendency significantly; a higher degree of oxidation leads to lower sorption. By controlling the degree of oxidation of the polysaccharides and the ionic strength of the sorption media, high degrees of sorption of carboxylated polysaccharides onto cellulose could, however, be obtained. Anionic polysaccharides were used as templates during laccase-catalyzed polymerization of aniline, offering a green, chemo-enzymatic route for synthesis of conducting polyaniline (PANI) composite materials. Different polysaccharide templates, such as, native GGM, TEMPO-oxidized GGM, naturally anionic κ-carrageenan, and nanofibrillated cellulose produced by TEMPO-oxidation, were assessed. The conductivity of the synthesized polysaccharide/PANI biocomposites varies depending on the polysaccharide template; κ-CGN, the anionic polysaccharide with the lowest pKa value, produces the polysaccharide/PANI biocomposites with the highest conductivity. The presented derivatization, sorption, and polymerization procedures open new application windows for polysaccharides, such as spruce GGM. The modified polysaccharides and the conducting biocomposites produced provide potential applications in biosensors, electronic devices, and tissue engineering.

Chemical changes in biomass during torrefaction

Torrefaction is moderate thermal treatment (~200-300 °C) of biomass in an inert atmosphere. The torrefied fuel offers advantages to traditional biomass, such as higher heating value, reduced hydrophilic nature, increased its resistance to biological decay, and improved grindability. These factors could, for instance, lead to better handling and storage of biomass and increased use of biomass in pulverized combustors. In this work, we look at several aspects of changes in the biomass during torrefaction. We investigate the fate of carboxylic groups during torrefaction and its dependency to equilibrium moisture content. The changes in the wood components including carbohydrates, lignin, extractable materials and ashforming matters are also studied. And at last, the effect of K on torrefaction is investigated and then modeled. In biomass, carboxylic sites are partially responsible for its hydrophilic characteristic. These sites are degraded to varying extents during torrefaction. In this work, methylene blue sorption and potentiometric titration were applied to measure the concentration of carboxylic groups in torrefied spruce wood. The results from both methods were applicable and the values agreed well. A decrease in the equilibrium moisture content at different humidity was also measured for the torrefied wood samples, which is in good agreement with the decrease in carboxylic group contents. Thus, both methods offer a means of directly measuring the decomposition of carboxylic groups in biomass during torrefaction as a valuable parameter in evaluating the extent of torrefaction. This provides new information to the chemical changes occurring during torrefaction. The effect of torrefaction temperature on the chemistry of birch wood was investigated. The samples were from a pilot plant at Energy research Center of the Netherlands (ECN). And in that way they were representative of industrially produced samples. Sugar analysis was applied to analyze the hemicellulose and cellulose content during torrefaction. The results show a significant degradation of hemicellulose already at 240 °C, while cellulose degradation becomes significant above 270 °C torrefaction. Several methods including Klason lignin method, solid state NMR and Py-GC-MS analyses were applied to measure the changes in lignin during torrefaction. The changes in the ratio of phenyl, guaiacyl and syringyl units show that lignin degrades already at 240 °C to a small extent. To investigate the changes in the extractives from acetone extraction during torrefaction, gravimetric method, HP-SEC and GC-FID followed by GC-MS analysis were performed. The content of acetone-extractable material increases already at 240 °C torrefaction through the degradation of carbohydrate and lignin. The molecular weight of the acetone-extractable material decreases with increasing the torrefaction temperature. The formation of some valuable materials like syringaresinol or vanillin is also observed which is important from biorefinery perspective. To investigate the change in the chemical association of ash-forming elements in birch wood during torrefaction, chemical fractionation was performed on the original and torrefied birch samples. These results give a first understanding of the changes in the association of ashforming elements during torrefaction. The most significant changes can be seen in the distribution of calcium, magnesium and manganese, with some change in water solubility seen in potassium. These changes may in part be due to the destruction of carboxylic groups. In addition to some changes in water and acid solubility of phosphorous, a clear decrease in the concentration of both chlorine and sulfur was observed. This would be a significant additional benefit for the combustion of torrefied biomass. Another objective of this work is studying the impact of organically bound K, Na, Ca and Mn on mass loss of biomass during torrefaction. These elements were of interest because they have been shown to be catalytically active in solid fuels during pyrolysis and/or gasification. The biomasses were first acid washed to remove the ash-forming matters and then organic sites were doped with K, Na, Ca or Mn. The results show that K and Na bound to organic sites can significantly increase the mass loss during torrefaction. It is also seen that Mn bound to organic sites increases the mass loss and Ca addition does not influence the mass loss rate on torrefaction. This increase in mass loss during torrefaction with alkali addition is unlike what has been found in the case of pyrolysis where alkali addition resulted in a reduced mass loss. These results are important for the future operation of torrefaction plants, which will likely be designed to handle various biomasses with significantly different contents of K. The results imply that shorter retention times are possible for high K-containing biomasses. The mass loss of spruce wood with different content of K was modeled using a two-step reaction model based on four kinetic rate constants. The results show that it is possible to model the mass loss of spruce wood doped with different levels of K using the same activation energies but different pre-exponential factors for the rate constants. Three of the pre-exponential factors increased linearly with increasing K content, while one of the preexponential factors decreased with increasing K content. Therefore, a new torrefaction model was formulated using the hemicellulose and cellulose content and K content. The new torrefaction model was validated against the mass loss during the torrefaction of aspen, miscanthus, straw and bark. There is good agreement between the model and the experimental data for the other biomasses, except bark. For bark, the mass loss of acetone extractable material is also needed to be taken into account. The new model can describe the kinetics of mass loss during torrefaction of different types of biomass. This is important for considering fuel flexibility in torrefaction plants.

Seed quality parameters of three interspecific hybrids of elephant grass x pearl millet

An interspecific hybrid resulting from the crossing of elephant grass (Pennisetum purpureum Schumach) x pearl millet (Pennisetum glaucum (L.) R. Brown) has been developed. This hybrid, however, revealed low phenotypic uniformity and low production of pure seeds. Through recurrent selection, two improved populations were obtained (genotypes Corte and Pastoreio). The aim of this study was assessing seed quality of the three hybrids (genotypes Corte, Pastoreio and Paraiso) by tests of: seed purity; seed germination; accelerated aging test, at 42 ºC; 1,000 seeds weight; drying curves; and sorption and desorption isotherms. Recurrent selection altered the seed size and increased initial quality of population for genotype Pastoreio. Drying curves for the three hybrids have shown similar behavior and reached moisture contents of 2.1%, 1.9%, and 1.8%, respectively, after 63 days. The accelerated aging test showed that hybrid Pastoreio was the most vigorous.

Desenvolupament de metodologia analítica per a la determinació de glifosat i adjuvants

El glifosat és un herbicida no selectiu àmpliament utilitzat en cultius agrícoles i zones no agrícoles que requereixen un control de la vegetació. Tot i la baixa toxicitat del glifosat en si mateix, la seva aplicació es realitza emprant formulacions comercials que contenen substàncies auxiliars que milloren l'eficàcia de l'herbicida, però modifiquen la toxicitat del producte final.Aquest treball s'ha centrat en la determinació de components de formulacions comercials d'herbicides i el seu comportament en el sòl. La primera part del treball s'ha dedicat al desenvolupament de mètodes d'anàlisi per a la determinació de glifosat i el seu principal metabòlit, AMPA, en matrius aquoses i sòls. A continuació s'ha desenvolupat un mètode d'anàlisi per les substàncies auxiliars addicionades freqüentment en les formulacions comercials, tensioactius no iònics. Finalment s'ha estudiat la mobilitat de l'herbicida en sòls de la zona mediterrània, incidint en els processos d'adsorció i degradació. També s'ha comparat el comportament de diversos herbicides comercials que contenen glifosat.

Results of an aqueous source term model for a radiological risk assessment of the Drigg LLW Site, U.K.

A radionuclide source term model has been developed which simulates the biogeochemical evolution of the Drigg low level waste (LLW) disposal site. The DRINK (DRIgg Near field Kinetic) model provides data regarding radionuclide concentrations in groundwater over a period of 100,000 years, which are used as input to assessment calculations for a groundwater pathway. The DRINK model also provides input to human intrusion and gaseous assessment calculations through simulation of the solid radionuclide inventory. These calculations are being used to support the Drigg post closure safety case. The DRINK model considers the coupled interaction of the effects of fluid flow, microbiology, corrosion, chemical reaction, sorption and radioactive decay. It represents the first direct use of a mechanistic reaction-transport model in risk assessment calculations.

Novos monômeros obtidos a partir do metacrilato de glicidila, bisfenol A e 4, 4 isopropilidenodicicloexanol : síntese, caracterização estrutural e propriedades de compósitos para utilização em resinas de restauração dental

Nowadays, composite resins are the direct restorative materials more important in dental clinical performance, due to their versatility and aesthetic excellence. Bis-GMA (2,2-bis[4(2-hydroxy-3-metacryloxypropoxy)phenil]propane) is the base monomer more frequently used in restorative composite resins. However, this monomer presents some disadvantages, such as high viscosity and two aromatic rings in its structure that can promote allergic reactions to the humans. In this work, the main purpose was to synthesize new monomers from glycidyl methacrylate to use in dental restorative materials. Structural characterization of the monomers was carried out through FTIR and NMR 1H, and eight composites were produced from the new monomers, by addition of silane-treated alumino silicate particles (inorganic filler) and a photocuring system (camphorquinone and ethyl 4-dimethylaminebenzoate). The composites were analyzed by environmental scanning electronic microscopy and the water sorption and solubility, compressive strength and elastic modulus were determined. A commercial composite resin [Z100 (3M)] was used to comparison effect. The new composites presented general characteristics similar to the commercial ones; however, they didn t present the properties expected. This behavior was attributed to the lower degree of monomer reaction and to the granulometry and size distribution of the mineral filler in the polymeric matrix

Determinação de Cd por FAAS em meio aquoso após pré-concentração em linha sobre SiAT

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Investigation of the pore blockage of a Brazilian dolomite during the sulfation reaction

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Micro-extração em fase sólida de Cu(II) e Cd(II) em meio aquoso utilizando sílica organicamente modificada para quantificação por espectrometria de absorção atômica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito do biocarvão sobre o comportamento da matéria orgânica e do fósforo em solo degradado

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Interações entre interferentes endócrinos e sedimento, turfa e espécies de plantas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de hidrogéis nanoestruturados baseados em polissacarídeo e zeólita para aplicação em sistemas de liberação controlada

Pós-graduação em Ciência dos Materiais - FEIS

Investigation of the pore blockage of a Brazilian dolomite during the sulfation reaction

The influence of the temperature and reaction time on the sulfation process of a dolomite is investigated in this paper. The sulfation effectiveness was evaluated and correlated with changes in the physical characteristics of a Brazilian dolomite during the reactive process. Calcination and sulfation experiments were performed under isothermal conditions for dolomite samples with average particle sizes of 545 mu m at temperatures of 750 degrees C, 850 degrees C and 950 degrees C at different times of sulfation. Thermogravimetric tests were applied to establish the reactivity variation of the dolomite in function of the time in the sulfation reaction and evaluate the methodology of the samples preparation. Porosimetry tests were performed to study the pore blockage of dolomite during the sulfation reaction. The highest values of BET surface area were 25.55 m(2)/g, 29.55 m(2)/g and 12.62 m(2)/g for calcined samples and after their sulfation processes, conversions of 51.5%, 61.9% and 42.8% were obtained at 750 degrees C, 850 degrees C and 950 degrees C, respectively. Considering the process as a whole, the best fit was provided by a first-order exponential decay equation. Moreover, the results have shown that it is possible to quantify the decreasing in the dolomite reactivity for sulfur dioxide sorption and understand the changes in the behavior of the sulfation process of limestones when applied to technologies, as fluidized bed combustor, in which sulfur dioxide is present. (C) 2011 Elsevier B. V. All rights reserved.