Short-circuit and ground fault analyses and location in VSC-based DC network cables

The application of high-power voltage-source converters (VSCs) to multiterminal dc networks is attracting research interest. The development of VSC-based dc networks is constrained by the lack of operational experience, the immaturity of appropriate protective devices, and the lack of appropriate fault analysis techniques. VSCs are vulnerable to dc-cable short-circuit and ground faults due to the high discharge current from the dc-link capacitance. However, faults occurring along the interconnecting dc cables are most likely to threaten system operation. In this paper, cable faults in VSC-based dc networks are analyzed in detail with the identification and definition of the most serious stages of the fault that need to be avoided. A fault location method is proposed because this is a prerequisite for an effective design of a fault protection scheme. It is demonstrated that it is relatively easy to evaluate the distance to a short-circuit fault using voltage reference comparison. For the more difficult challenge of locating ground faults, a method of estimating both the ground resistance and the distance to the fault is proposed by analyzing the initial stage of the fault transient. Analysis of the proposed method is provided and is based on simulation results, with a range of fault resistances, distances, and operational conditions considered.

High performance numerical modeling of ultra-short laser pulse propagation based on multithreaded parallel hardware

The focus of this study is development of parallelised version of severely sequential and iterative numerical algorithms based on multi-threaded parallel platform such as a graphics processing unit. This requires design and development of a platform-specific numerical solution that can benefit from the parallel capabilities of the chosen platform. Graphics processing unit was chosen as a parallel platform for design and development of a numerical solution for a specific physical model in non-linear optics. This problem appears in describing ultra-short pulse propagation in bulk transparent media that has recently been subject to several theoretical and numerical studies. The mathematical model describing this phenomenon is a challenging and complex problem and its numerical modeling limited on current modern workstations. Numerical modeling of this problem requires a parallelisation of an essentially serial algorithms and elimination of numerical bottlenecks. The main challenge to overcome is parallelisation of the globally non-local mathematical model. This thesis presents a numerical solution for elimination of numerical bottleneck associated with the non-local nature of the mathematical model. The accuracy and performance of the parallel code is identified by back-to-back testing with a similar serial version.

An assessment of creep deformation and fracture behavior of 2.25Cr-1Mo similar and dissimilar weld joints

The evaluation of the creep deformation and fracture behavior of a 2.25Cr-1Mo steel base metal, a 2.25Cr-1Mo/2.25Cr-1Mo similar weld joint, and a 2.25Cr-1Mo/Alloy 800 dissimilar weld joint at 823 K over a stress range of 90 to WO MPa has been carried out. The specimens for creep testing were taken from single-V weld pads fabricated by a shielded metal arc-welding process using 2.25Cr-1Mo steel (for similar-joint) and INCONEL 182 (for dissimilar-joint) electrodes. The weld pads were subsequently given a postweld hear treatment (PWHT) of 973 K for I hour. The microstructure and microhardness of the weld joints were evaluated in the as-welded, postweld heat-treated, and creep-tested conditions. The heat-affected zone (HAZ) of similar weld joint consisted of bainite in the coarse-prior-austenitic-grain (CPAG) region near the fusion line, followed by bainite in the fine-prior-austenitic-grain (FPAG) and intercritical regions merging with the unaffected base metal. In addition to the HAZ structures in the 2.25Cr-1Mo steel, the dissimilar weld joint displayed a definite INCONEL/2.25Cr-1Mo weld interface structure present either as a sharp line or as a diffuse region. A hardness trough was observed in the intercritical region of the HAZ in both weld joints, while a maxima in hardness was seen at the weld interface of the dissimilar weld joint. Both weld joints exhibited significantly lower rupture lives compared to the 2.25Cr-1Mo base metal. The dissimilar weld joint exhibited poor rupture life compared to the similar weld joint, at applied stresses lower than 130 MPa. In both weld joints, the strain distribution across the specimen gage length during creep testing varied significantly. During creep testing, localization of deformation occurred in the intercritical HAZ. In the similar weld joint, at all stress levels investigated, and in the dissimilar weld joint, at stresses greater than or equal to 150 MPa, the creep failure occulted in the intercritical HAZ. The fracture occurred by transgranular mode with a large number of dimples. At stresses below 150 MPa, the failure in the dissimilar weld joint occurred in the CPAG HAZ near to the weld interface. The failure occurred by extensive intergranular creep cavity formation.

An assessment of creep deformation and fracture behavior of 2.25Cr-1Mo

The evaluation of the creep deformation and fracture behavior of a 2.25Cr-1Mo steel base metal, a 2.25Cr-1Mo/2.25Cr-1Mo similar weld joint, and a 2.25Cr-1Mo/Alloy 800 dissimilar weld joint at 823 K over a stress range of 90 to WO MPa has been carried out. The specimens for creep testing were taken from single-V weld pads fabricated by a shielded metal arc-welding process using 2.25Cr-1Mo steel (for similar-joint) and INCONEL 182 (for dissimilar-joint) electrodes. The weld pads were subsequently given a postweld hear treatment (PWHT) of 973 K for I hour. The microstructure and microhardness of the weld joints were evaluated in the as-welded, postweld heat-treated, and creep-tested conditions. The heat-affected zone (HAZ) of similar weld joint consisted of bainite in the coarse-prior-austenitic-grain (CPAG) region near the fusion line, followed by bainite in the fine-prior-austenitic-grain (FPAG) and intercritical regions merging with the unaffected base metal. In addition to the HAZ structures in the 2.25Cr-1Mo steel, the dissimilar weld joint displayed a definite INCONEL/2.25Cr-1Mo weld interface structure present either as a sharp line or as a diffuse region. A hardness trough was observed in the intercritical region of the HAZ in both weld joints, while a maxima in hardness was seen at the weld interface of the dissimilar weld joint. Both weld joints exhibited significantly lower rupture lives compared to the 2.25Cr-1Mo base metal. The dissimilar weld joint exhibited poor rupture life compared to the similar weld joint, at applied stresses lower than 130 MPa. In both weld joints, the strain distribution across the specimen gage length during creep testing varied significantly. During creep testing, localization of deformation occurred in the intercritical HAZ. In the similar weld joint, at all stress levels investigated, and in the dissimilar weld joint, at stresses greater than or equal to 150 MPa, the creep failure occulted in the intercritical HAZ. The fracture occurred by transgranular mode with a large number of dimples. At stresses below 150 MPa, the failure in the dissimilar weld joint occurred in the CPAG HAZ near to the weld interface. The failure occurred by extensive intergranular creep cavity formation.

Projeto e desenvolvimento de células robotizadas para soldadura e cladding

A utilização de equipamentos robóticos para o processo de soldadura por arco elétrico teve um forte crescimento nas décadas de 80 e 90, altura em que o custo e fiabilidade da tecnologia passou a permitir a integração de robôs em linhas de produção ou em células de fabrico. Depressa cresceram as exigências de uma produção com qualidade repetitiva e facilmente ajustável, e as restrições ao uso de processos manuais ou de tecnologias com pouca flexibilidade. Desde o início do século XXI que a renovação de uma estação de fabrico de peças soldadas para produção em série, especialmente no setor automóvel, parece forçada à integração de robôs industriais, que assim se tornaram símbolos de produtividade. A KAMAZ encontra-se atualmente a renovar alguns dos seus processos de fabrico, incluindo as áreas de soldadura por arco ou cladding. Esta Dissertação aborda o trabalho elaborado, depois de contratualizada com a ABB Rússia a instalação de novas células de fabrico robotizado nesta empresa. Este projeto tem início com o levantamento das necessidades, a verificação do processo existente, e a procura da solução tecnológica que se adapte a essas condições e cumpra os requisitos acordados. São realizadas modelações e simulações off-line em 3D, usando o software RobotStudio da ABB, que permitiram testar cada solução e analisar a sua adequação e viabilidade. Para maior garantia de se obter a qualidade esperada na fusão e deposição do material por processo com arco elétrico revestido a gás, foram realizados testes reais utilizando equipamento robótico em condições baseadas nos testes feitos no ambiente virtual. Por último, são ajustadas as localizações dos postos de trabalho ao layout existente e é feito o balanceamento do tempo de operação manual com o tempo do processo robotizado. Este projeto de Tese termina com a aceitação do cliente para a solução encontrada e para os resultados dos testes reais de ambos os processos.

Risque de cancer du poumon associé aux expositions environnementales de fumées de soudage : 2 études cas-témoins basées sur la population montréalaise.

Objectif : Examiner la relation entre une exposition professionnelle aux fumées de soudage au gaz et à l’arc et le risque de développer un cancer du poumon, chez des travailleurs provenant de différents milieux de travail et exposés à de nombreuses substances de différentes concentrations. Méthodes : Nous avons mené deux études cas-témoins basés sur la population montréalaise (1979-86 et 1996-2001), incluant respectivement 857 et 736 cas, ainsi que des témoins appariés selon la fréquence des cas, le sexe et le lieu de résidence. Un historique détaillé des emplois occupés fut obtenu par entrevue et évalué par une équipe d’experts afin d’estimer l’intensité, la durée ainsi que l’exposition cumulative à un grand nombre de substances. Les fumées de soudage au gaz et à l’arc sont parmi les substances évaluées et nous avons pu calculer un rapport de cote (RC) et son intervalle de confiance de 95% (IC 95%) pour le risque de cancer du poumon en utilisant la régression logistique et en ajustant pour l’historique de tabagisme et plusieurs autres covariables pertinentes. Des analyses subséquentes ont permis d’explorer d’autres voies, comme la modification des effets observés par le tabagisme. Résultats : Les résultats obtenus à partir des deux études étant assez similaires, nous avons donc pu les combiner pour former une seule étude. Aucune association statistiquement significative n’a été trouvée entre le cancer du poumon et les fumées de soudage au gaz (RC=1,13; IC 95%=0,90-1,42) et les fumées de soudage à l’arc (RC=1,01; IC 95%=0,80-1,26). Par contre, dans le sous-groupe des non-fumeurs et fumeurs très légers, nous avons trouvé un risque accru de cancer du poumon en relation avec les fumées de soudage au gaz (RC=2,78; IC 95%=1,66-4,65) et à l’arc (RC=2,20; IC 95%=1,32-3,70). En se concentrant sur ce sous-groupe, nous avons trouvé un risque encore plus élevé de développer un cancer du poumon pour ceux exposé à des doses plus substantielles, pour le soudage au gaz (RC=4,63; IC 95%=2,14-10,03) et à l’arc (RC=3,45; IC 95%=1,59-7,48). Discussion : Globalement, aucun excès de risque causé par une exposition aux fumées de soudage n’a été détecté, mais un excès a été trouvé chez les non-fumeurs et fumeurs légers uniquement et ce, pour les deux types de fumées de soudage. L’effet des fumées de soudage peut être voilé chez les fumeurs, ou bien les non-fumeurs pourraient être plus vulnérables.

Relacao entre o angulo da ponta do eletrodo e a geometria do cordao de solda no processo de soldagem tig

No processo de soldagem TIG (Tungstênio Inerte Gás), um dos fatores que influenciam o formato do cordão de solda é o ângulo da extremidade do eletrodo. Para estudar o comportamento do arco elétrico em função da geometria de ponta do eletrodo e suas conseqüências nos cordões de solda, efetuaram-se soldagens sobre corpos de prova sem deposição de material (bead-on-plate) através de parâmetros controlados e a mecanização do processo. Parâmetros tais como vazão do gás, velocidade de avanço da tocha e comprimento do arco foram testados para verificar a atuação em conjunto com o ângulo do eletrodo. Pela análise metalográfica (macrografia) estudaram-se os perfis dos cordões de solda, verificando-se que o ângulo exerce uma influência significativa na característica do arco tensão-corrente, na largura e profundidade de penetração da solda. Para maiores ângulos de extremidade do eletrodo obteve-se aumento na penetração, diminuição da tensão e largura do cordão de solda para uma mesma intensidade de corrente.

Automatic microstructural characterization and classification using artificial intelligence techniques on ultrasound signals

Secondary phases such as Laves and carbides are formed during the final solidification stages of nickel based superalloy coatings deposited during the gas tungsten arc welding cold wire process. However, when aged at high temperatures, other phases can precipitate in the microstructure, like the γ″ and δ phases. This work presents a new application and evaluation of artificial intelligent techniques to classify (the background echo and backscattered) ultrasound signals in order to characterize the microstructure of a Ni-based alloy thermally aged at 650 and 950 °C for 10, 100 and 200 h. The background echo and backscattered ultrasound signals were acquired using transducers with frequencies of 4 and 5 MHz. Thus with the use of features extraction techniques, i.e.; detrended fluctuation analysis and the Hurst method, the accuracy and speed in the classification of the secondary phases from ultrasound signals could be studied. The classifiers under study were the recent optimum-path forest (OPF) and the more traditional support vector machines and Bayesian. The experimental results revealed that the OPF classifier was the fastest and most reliable. In addition, the OPF classifier revealed to be a valid and adequate tool for microstructure characterization through ultrasound signals classification due to its speed, sensitivity, accuracy and reliability. © 2013 Elsevier B.V. All rights reserved.

Avaliação da resistência ao desgaste abrasivo de revestimentos soldados do tipo Fe-C-Cr utilizados na indústria sucroalcooleira

Pós-graduação em Engenharia Mecânica - FEIS

Ultrasonic sensor signals and optimum path forest classifier for the microstructural characterization of thermally-aged inconel 625 alloy

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Fatigue of tube-to-plate fillet welds and methods for their improvement /

"July 1997."

A Comparative Study Of Tensile And Microstructural Characteristics Of Friction Welded Joints And Conventionally Welded Joints Of Aluminium Alloy 6061

Welding of high strength and low weight materials like Aluminium Alloys without any defects by conventional welding techniques is a major challenge in industries. Hence research on solid state welding techniques like Friction stir welding and Friction welding techniques have got much importance in joining of Aluminium alloys. However most of the industries are not changing conventional techniques as skilled workers are available on that area. Most common conventional welding techniques used for joining of Aluminium alloys are Gas welding and Arc welding. Friction welding is a solid-state welding process that generates heat through mechanical friction between a moving and a stationary component with the addition of a lateral force called “upset” to plast ically displace and fuse the materials. In this work, experimental study on tensile and micro structural characteristics of welded joints formed from conventional welding techniques and Rotary friction welding(suitable for weld specimens with circular cross section) has been carried out and the same were compared. The process parameters for arc welding used was 50-70 Amp reverse polarity DC and electrodes of 2.3mm diameter. In Gas welding, the parameters were oxy acetylene neural flame at 3200°C and 3mm electrodes . In the case of friction welding an axial pressure loading of 3Mpa with 5 MPa as upsetting pressure and 500 rpm were used to obtain good welded joints. Tensile characteristic studies of Arc welded joints and Gas welded joints showed 48% and 60 % variations respectively from the maximum load bearing characteristics of parent metal. In the case of friction welded joint, the variation was found to 46%. Micro structural evaluation of conventionally welded joints exhibited clear distinct zones of various weld regions. In the case of friction welded joint micro structural photographs showed comparable features both in parent metal and welded region. Thus the tensile characteristic study and microstructure evaluations proved that friction welded joints are good in both aspects compared to conventionally welded joints.

10 GHz optical short pulse generation using tandem electroabsorption modulators monolithically integrated with distributed feedback laser by ultra-low-pressure selective area growth

In this work, a novel light source of tandem InGaAsP/InGaAsP multiple quantum well electroabsoption modulator( EAM ) monolithically integrated with distributed feedback laser is fabricated by ultra-low-pressure ( 22 x 10(2) Pa ) selective area growth metal-organic chemical vapor diposition technique. Superior device performances have been obtained, such as low threshold current of 19 mA, output light power of 4.5 mW, and over 20 dB extinction ratio at 5 V applied voltage when coupled into a single mode fiber. Over 10 GHz 3dB bandwidth in EAM part is developed with a driving voltage of 2 V. Using this sinusoidal voltage driven integrated device, 10 GHz repetition rate pulse with an actual width of 13.7 ps without any compression elements is obtained due to the gate operation effect of tandem EAMs.

The development and validation of computational MHD techniques for the modelling of metal production processes

Magnetic fields are used in a number of processes related to the extraction of metals, production of alloys and the shaping of metal components. Computational techniques have an increasingly important role to play in the simulation of such processes, since it is often difficult or very costly to conduct experiments in the high temperature conditions encountered and the complex interaction of fluid flow, heat transfer and magnetic fields means simple analytic models are often far removed from reality. In this paper an overview of the computational activity at the University of Greenwich is given in this area, covering the past ten years. The overview is given from the point of view of the modeller and within the space limitations imposed by the format it covers the numerical methods used, attempts at validation against experiments or analytic procedures; it highlights successes, but also some failures. A broad range of models is covered in the review (and accompanying lecture), used to simulate (a) A-C field applications: induction melting, magnetic confinement and levitation, casting and (b) D-C field applications such as: arc welding and aluminium electroloysis. Most of these processes involve phase change of the metal (melting or solidification), the presence of a dynamic free surface and turbulent flow. These issues affect accuracy and need to be address by the modeller.

Efeito da temperatura de pré-aquecimento e características do pulso na microestrutura de aço estrutural de alta resistência e baixa liga soldado com arco elétrico e proteção gasosa

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)