Computer aided ultrasonic thickness strain analysis of automotive sheet metal stampings using FEA information

This paper discusses a computer-aided methodology for thickness strain analysis (TSA) of sheet metal stampings using geometry and strain information that is extracted from finite element analysis (FEA) results. The system utilises both FEA results and an ultrasonic gauge capability expert system to assist press shop personnel, providing them with capabilities such as optimum measurement point location and an estimate of gauge error. Key advantages of this enhanced TSA methodology are related to overall efficiency and accuracy gains.

Galling reduction through die surface treatment - testing three treatments for sheet metal stamping

This brief article describes how tool galling occurs in stamping and describes results of tests on how TiCN, Hard-Cr, and CrCN were used on sample parts to help reduce galling.

Multivariate modelling of variability in sheet metal forming

The inherent variability in incoming material and process conditions in sheet metal forming makes quality control and the maintenance of consistency extremely difficult. A single FEM simulation is successful at predicting the formability for a given system, however lacks the ability to capture the variability in an actual production process due to the numerical deterministic nature. This paper investigates a probabilistic analytical model where the variation of five input parameters and their relationship to the sensitivity of springback in a stamping process is examined. A range of sheet tensions are investigated, simulating different operating windows in an attempt to highlight robust regions where the distribution of springback is small. A series of FEM simulations were also performed, to compare with the findings from the analytical model using AutoForm Sigma v4.04 and to validate the analytical model assumptions.

Results show that an increase in sheet tension not only decreases springback, but more importantly reduces the sensitivity of the process to variation. A relative sensitivity analysis has been performed where the most influential parameters and the changes in sensitivity at various sheet tensions have been investigated. Variation in the material parameters, yield stress and n-value were the most influential causes of springback variation, when compared to process input parameters such as friction, which had a small effect. The probabilistic model presented allows manufacturers to develop a more comprehensive assessment of the success of their forming processes by capturing the effects of inherent variation.

Simulation of contact pressure in sheet metal trimming/blanking process

In the car body stamping process, trim/blank die cutting edges are subjected to very high tribological loads that result in loss of tool material from both the punch and die cutting edges. According to Archard’s wear model, normal contact force and sliding distance directly affects the wear. Therefore, knowledge of the acting forces on local contact areas has a pivotal role towards the prediction of tool wear. This paper presents a finite element modelling approach to determining the contact pressure distribution on the tool cutting edges during a trimming/blanking process. Characteristic areas on sheared edge profile, variation of punch force and high contact pressures affected areas have also been analysed.

Contact pressure evolution and its relation to wear in sheet metal forming

For a given sheet metal forming process, an accurate determination of the contact pressure distribution is an essential step towards the estimation of tool life. This investigation utilizes finite element (FE) analysis to model and explain the evolution and distribution of contact pressure over the die radius, throughout the duration of a channel forming process. It was found that a typical two-peak steady-state contact pressure response exists for the majority of the process. However, this was preceded by an initial transient response, characterized by extremely large and localized contact pressures, which were more than double the magnitude of the steady-state peak pressure. The validity of the predicted contact pressure behavior was assessed via detailed numerical analysis and by examining the wear response of an experimental stamping operation. The experimental results revealed that the high contact pressure zones of the transient response corresponded to a severe galling wear mechanism. Therefore, the transient response may be of primary significance to the tool wear response; thus questioning the applicability of traditional bending-under-tension wear tests for sheet metal stamping processes. Finally, a parametric study was conducted, examining the influence of the major process parameters on the steady-state and peak transient contact pressures, using the developed FE model. It was found that the bend ratio and the blank material ultimate tensile strength had the most influence on the peak contact pressures. The main process-related parameters, friction coefficient and blank holder force, were found to have only a minor influence.

Contact pressure prediction in sheet metal forming using finite element analysis

Tool wear has become a significant issue associated with the forming of high strength sheet steels in the automotive industry. In order to combat this problem, recent research has been devoted to utilizing the contact results obtained from current sheet metal forming software predictions, in order to develop/apply tool wear models or tool material selection criteria for use in the stamping plant. This investigation aims to determine whether a specialized sheet metal forming software package can correctly capture the complex contact conditions that occur during a typical sheet metal stamping process. The contact pressure at the die radius was compared to results obtained using a general-purpose finite element software package, for a simple channel-forming process. Although some qualitative similarities between the two predictions were observed, it was found that significant differences in the magnitude and distribution of the contact pressure exists. The reasons for the discrepancies in results are discussed with respect to the simplifications and assumptions adopted in the finite element model definitions, and with regards to other results available in the literature.

Evaluating lubricants in sheet metal forming

The sheet metal forming process basically involves the shaping of sheet metal of various thickness and material properties into the desired contours. This metal forming process has been extensively used by the automotive industry to manufacture both car panels and parts. Over the years numerous investigations have been conducted on various aspects of the manufacturing process with varied success. In recent years the requirements on the sheet metal forming industry have headed towards improved stability in the forming process while lowering environmental burdens. Therefore the overall aim of this research was to identify a technique for developing lubricant formulations that are insensitive to the sheet metal forming process. Due to the expense of running experiments on production presses and to improve time efficiency of the process the evaluation procedure was required to be performed in a laboratory. Preliminary investigations in the friction/lubricant system identified several laboratory tests capable of measuring lubricant performance and their interaction with process variables. However, little was found on the correlation between laboratory tests and production performance of lubricants. Therefore the focus of the research switched to identifying links between the performance of lubricants in a production environment and laboratory tests. To reduce the influence of external parameters all significant process variables were identified and included in the correlation study to ensure that lubricant formulations could be desensitised to all significant variables. The significant process variables were found to be sensitive to die position, for instance: contact pressure, blank coating of the strips and surface roughness of the dies were found significant for the flat areas of the die while no variables affected friction when polished drawbeads were used. The next phase was to identify the interaction between the significant variables and the main lubricant ingredient groups. Only the fatty material ingredient group (responsible for the formation of boundary lubricant regimes) was found to significantly influence friction with no interaction between the ingredient groups. The influence of varying this ingredient group was then investigated in a production part and compared to laboratory results. The correlation between production performance and laboratory tests was found to be test dependant. With both the Flat Face Friction test and the Drawbead Simulator unaffected by changes in the lubricant formulation, while the Flat Bottom Cup test showing similar results as the production trial. It is believed that the lack of correlation between the friction tests and the production performance of the lubricant is due to the absence of bulk plastic deformation of the strip. For this reason the Ohio State University (OSU) friction test was incorporated in the lubricant evaluation procedure along with a Flat Bottom Cup test. Finally, it is strongly believed that if the lubricant evaluation procedure highlighted in this research is followed then lubricant formulations can be developed confidently in the laboratory.

Sheared edge quality in the trimming of sheet metals

Examines the sheared edge quality of different automotive sheet metals resulting from the trimming process using experimental tooling and finite element modelling. The significant differences in burr, sliver and edge profile formation have been explained in terms of the strain distribution and tensile properties of the materials.

Investigation on the forming behaviour of metal/polymer laminates

A metal/polymer laminate is a new light weight sheet material suitable to replace conventional steel or aluminium sheet in future car designs. In this study the effect of material composition and process conditions on the forming behaviour of metal/polymer laminates in sheet metal forming was investigated by experimental, analytical and numerical methods.

Tool wear analysis in sheet metal stamping

This thesis advances the understanding of die wear in sheet metal stamping. It was found that transient conditions exist at the die radius, resulting in severe contact pressures that are critical to the wear behaviour. The findings challenge applicability of traditional wear tests and models for sheet metal stamping processes.

Sliding distance, contact pressure and wear in sheet metal stamping

This paper directly examines the contact sliding distance experienced during a typical sheet metal stamping process-an area that has largely been neglected in the literature. A method to numerically quantify the sliding distance is proposed. The sliding distance predicted from this method, and the contact pressure obtained from numerical simulation, allow the recently identified time-dependent contact conditions on the die and blank surfaces to be completely characterized. Consequently, a new insight into the wear/galling that occurs at the die radius in sheet metal stamping is gained. The results show that the region close to zero degrees on the die radius is likely to experience the most wear, with the identified transient stage contributing to a large proportion of the total wear. Additionally, the region on the blank surface often observed to be heavily burnished - the die impact line - is estimated to experience the highest wear severity due to the transient contact conditions. The proposed method to numerically quantify the sliding contact conditions can be applied as a general approach to study any other two-body sliding contact situations.

Effects of temperature in relation to sheet metal stamping

The demand to reduce the use of lubricants and increase tool life in sheet metal stamping has resulted in increased research on the sliding contact between the tool and the sheet materials. Unlubricated sliding wear tests for soft carbon steel sliding on D2 tool steel were performed using a pin-on-disk tribometer. The results revealed that temperature has an influencing role in the wear of tool steel and that material transfer between tool and sheet can be minimized at a certain temperature range in sheet metal stamping.

Tool wear in sheet metal stamping

This paper discusses our recent research on wear at the die radius in sheet metal stamping. According to wear theory, contact pressure and sliding distance are the two dominant factors in determining sliding wear. We applied the finite element analysis to accurately quantify the contact pressure and sliding distance at the die radius in sheet metal stamping. The results were then applied to analyze sliding wear at the die radius. We found that a typical two-peak steady-state contact pressure response exists during a channel forming process. The steady-state contact pressure response was preceded by an initial transient response, which produced extremely large and localized contact pressures. We proposed a method to numerically quantify the sliding distance, which was applied to examine the contact sliding distance at the die radius. Correlating the contact pressure and sliding distance, a new insight into the wear/galling that occurs at the die radius in sheet metal stamping was gained. The results show that the region close to zero degrees on the die radius is likely to experience the most wear, with the identified transient stage contributing to a large proportion of the total wear.