Biogas and bio-hydrogen: production and uses. A review

The first part of this essay aims at investigating the already available and promising technologies for the biogas and bio-hydrogen production from anaerobic digestion of different organic substrates. One strives to show all the peculiarities of this complicate process, such as continuity, number of stages, moisture, biomass preservation and rate of feeding. The main outcome of this part is the awareness of the huge amount of reactor configurations, each of which suitable for a few types of substrate and circumstance. Among the most remarkable results, one may consider first of all the wet continuous stirred tank reactors (CSTR), right to face the high waste production rate in urbanised and industrialised areas. Then, there is the up-flow anaerobic sludge blanket reactor (UASB), aimed at the biomass preservation in case of highly heterogeneous feedstock, which can also be treated in a wise co-digestion scheme. On the other hand, smaller and scattered rural realities can be served by either wet low-rate digesters for homogeneous agricultural by-products (e.g. fixed-dome) or the cheap dry batch reactors for lignocellulose waste and energy crops (e.g. hybrid batch-UASB). The biological and technical aspects raised during the first chapters are later supported with bibliographic research on the important and multifarious large-scale applications the products of the anaerobic digestion may have. After the upgrading techniques, particular care was devoted to their importance as biofuels, highlighting a further and more flexible solution consisting in the reforming to syngas. Then, one shows the electricity generation and the associated heat conversion, stressing on the high potential of fuel cells (FC) as electricity converters. Last but not least, both the use as vehicle fuel and the injection into the gas pipes are considered as promising applications. The consideration of the still important issues of the bio-hydrogen management (e.g. storage and delivery) may lead to the conclusion that it would be far more challenging to implement than bio-methane, which can potentially “inherit” the assets of the similar fossil natural gas. Thanks to the gathered knowledge, one devotes a chapter to the energetic and financial study of a hybrid power system supplied by biogas and made of different pieces of equipment (natural gas thermocatalitic unit, molten carbonate fuel cell and combined-cycle gas turbine structure). A parallel analysis on a bio-methane-fed CCGT system is carried out in order to compare the two solutions. Both studies show that the apparent inconvenience of the hybrid system actually emphasises the importance of extending the computations to a broader reality, i.e. the upstream processes for the biofuel production and the environmental/social drawbacks due to fossil-derived emissions. Thanks to this “boundary widening”, one can realise the hidden benefits of the hybrid over the CCGT system.

Sviluppo di un sistema integrato innovativo per la contemporanea produzione e separazione di H2 ultrapuro, attraverso oxy-reforming, water-gas shift e membrane al Pd

Il presente lavoro di tesi si è focalizzato sullo studio e sulla ottimizzazione di un sistema integrato, che utilizzi la reazione di oxy-reforming del metano al fine di produrre syngas che venga trattato attraverso la water-gas shift al fine di abbattere il contenuto di CO e al tempo stesso aumentare la resa in H2. Con l’obiettivo di ottenere H2 ad elevata purezza (>99%) da poter essere inviato direttamente a celle a combustible ed in impianti di piccola taglia con possibile delocalizzazione della produzione industriale di energia elettrica e termica “pulita”, la miscela reale uscente dal processo di oxy-reforming è stata processata tramite successiva water-gas shift direttamente all’interno di una membrana ceramica al Pd selettiva nella separazione di H2. L’innovativià di questo progetto di studio è data da diversi parametri quali: 1) l’impiego dell’oxy-reforming in alternativa al normale steam-reforming del CH4, che permette di condurre il processo a temperature decisamente inferiori (700-750°C), utilizzando un minor quantitativo di vapore (S/C = 0.7); 2) l’utilizzo di due nuove formulazioni di catalizzatore di WGS per alte temperature, capace di operare in un unico stadio conversioni di CO ottenibili industrialmente solo attraverso i convenzionali due due stadi di reazione (e due diverse formulazioni di catalizzatori a base di Fe/Cr e Cu); 3) l’utilizzo di supporti ceramici con membrana a base di Pd, capaci di ospitare al loro interno un catalizzatore eterogeneo per la reazione di WGS a 400°C, rendendo quindi possibile la produzione e contemporanea separazione di H2 con un ulteriore effetto positivo poiché la membrana rimuovendo H2 dalla zona di reazione favorisce il superamento dell’equilibrio termodinamico per la conversione del CO, abbassandone il contenuto nel flusso uscente dei gas reazione e rendendo non più necessari sistemi aggiuntivi di separazione quali PSA o PROXY.

Sviluppo di un gassificatore downdraft da 20kWe e analisi dei prodotti

L’elaborato affronta i temi dello sviluppo sostenibile, dell’affrancamento dalle risorse fossili e della produzione di energetica capillare. Nell’ambito di un progetto di ricerca mirato allo sviluppo di un gassificatore downdraft di tipo Imbert da 20kWe alimentato a legno cippato, viene qui presentato l’avviamento della campagna sperimentale su un impianto pilota. Particolare attenzione viene rivolta alla biomassa e ai prodotti di gassificazione (char, tar e syngas), le cui caratterizzazioni hanno contribuito all’evoluzione impiantistica e protocollare, interamente descritte nel testo.

Micro combined heat and power laboratory development

Micro Combined Heat and Power (Micro-CHP) system produces both electricity and heat required for residential or small business applications. Use of Micro-CHP in a residential application not only creates energy and economic savings but also reduces the carbon foot print of the house or small business. Additionally, micro-CHP can subsidize its cost of operation by selling excess electricity produced back to the grid. Even though Micro-CHP remains attractive on paper, high initial cost and optimization issues in residential scale heat and electrical requirement has kept this technology from becoming a success. To understand and overcome all disadvantages posed my Micro-CHP system, a laboratory is developed to test different scenarios of Micro-CHP applications so that we can learn and improve the current technology. This report focuses on the development of this Micro-CHP laboratory including installation of Ecopower micro-CHP unit, developing fuel line and exhaust line for Ecopower unit, design of electrical and thermal loop, installing all the instrumentation required for data collection on the Ecopower unit and developing controls for heat load simulation using thermal loop. Also a simulation of Micro-CHP running on Syngas is done in Matlab. This work was supported through the donation of ‘Ecopower’ a Micro-CHP unit by Marathon Engine and through the support of Michigan Tech REF-IF grand.

Analysis of the Behaviour of Biofuel-Fired Gas Turbine Power Plants

The utilisation of biofuels in gas turbines is a promising alternative to fossil fuels for power generation. It would lead to significant reduction of CO2 emissions using an existing combustion technology, although significant changes seem to be needed and further technological development is necessary. The goal of this work is to perform energy and exergy analyses of the behaviour of gas turbines fired with biogas, ethanol and synthesis gas (bio-syngas), compared with natural gas. The global energy transformation process (i.e. from biomass to electricity) has also been studied. Furthermore, the potential reduction of CO2 emissions attained by the use of biofuels has been determined, considering the restrictions regarding biomass availability. Two different simulation tools have been used to accomplish the aims of this work. The results suggest a high interest and the technical viability of the use of Biomass Integrated Gasification Combined Cycle (BIGCC) systems for large scale power generation.

Estudio energético comparativo de diferentes configuraciones de ciclo combinado

El objetivo del presente proyecto consiste en la modelización y optimización de una planta de gasificación integrada en ciclo combinado de 400 MW de potencia neta, mediante el uso del programa Cycle-Tempo, desarrollado por la Universidad de Delft. Para la modelización de la planta, se ha dividido en sus dos unidades principales: la isla de gasificación y el ciclo combinado. Para la validación del modelo de la isla de gasificación, se ha utilizado una composición de referencia de un combustible gasificable y se ha obtenido la composición del gas de síntesis esperada. Se han modelado y optimizado varias configuraciones de ciclo combinado, variando los parámetros característicos de la caldera de recuperación de calor. Se ha realizado la integración de las dos unidades para maximizar la potencia entregada por la planta. Finalmente, se ha estimado el balance anual de energía del ciclo combinado alimentado con gas natural y con el gas de síntesis, con el fin de comparar las rentabilidades económicas obtenidas. Mediante el estudio realizado, se deduce que la forma más eficiente de producir energía, a partir del uso del carbón, es la tecnología de gasificación integrada en ciclo combinado, pese a que su rendimiento sea inferior al ciclo combinado alimentado con gas natural. ABSTRACT The aim of this project is the modeling and optimization of an integrated gasification combined cycle plant of 400 MW net power, using the Cycle-Tempo program, developed by the University of Delft. For the modeling of the plant, it has been divided into its two main units: the island of gasification and the combined cycle. For the model validation of the gasification island, a reference composition of a gasifiable fuel has been used and the expected synthesis gas composition was obtained. Several configurations of combined cycle have been modeled and optimized by varying the characteristic parameters of the heat recovery steam generator. It has made the integration of the two units to reach maximum optimization of power, which has been delivered by the plant. Finally, it has been estimated the annual energy balance for the combined cycle plant fueled with natural gas and with syngas, in order to compare the profitability obtained with each one. Through the study, it is deduced that the most efficient way to produce energy from the use of coal, is the integrated gasification combined cycle technology, although their performance is lower than that obtained from the combined cycle fueled with natural gas.

Energía renovable a partir de los lodos de depuradoras urbanas

El lodo de depuradora es el residuo líquido o semilíquido procedente de las Estaciones Depuradoras de Aguas Residuales (EDARs) del que puede obtenerse una energía renovable empleando la tecnología de la gasificación. Esta tecnología consiste en la oxidación parcial del sustrato carbonoso del lodo a altas temperaturas bajo condiciones subestequiométricas de aire, oxígeno u otros agentes gasificantes. Los productos obtenidos mediante gasificación son: un gas de síntesis (SYNGAS, con composición variable de H2, CO) un residuo carbonizado (char) y una fracción líquida de compuestos orgánicos de distinto peso molecular denominados alquitranes. El gas de síntesis tiene aplicaciones como son la generación de energía eléctrica/térmica o la síntesis de compuestos químicos. Sin embargo, la presencia de alquitranes imposibilita su uso en buena parte de las aplicaciones. El trabajo realizado que aquí se presenta estudia la posibilidad de tratar los lodos de depuradora mediante gasificación. Para ello, se han realizado las siguientes tareas: - Caracterización del lodo incluyendo la determinación de su humedad, materia orgánica, análisis elemental (C, N, H, S) y contenido de metales pesados (Cd, Cu, Ni, Pb, Zn, Hg y Cr). - Estudios de termogravimetría (TGA) del lodo para conocer su comportamiento térmico y la temperatura a la que se producen las principales reacciones en la gasificación. - Gasificación en un equipo de lecho fluido burbujeante y alimentación en continuo a escala de laboratorio. Con dicho gasificador se ha experimentado a distintas temperaturas y cargas para conocer las condiciones de proceso más favorables para aumentar la producción y el poder calorífico del SYNGAS obteniendo, a la vez, una baja producción en alquitranes. Para ello se ha analizado la composición de los gases obtenidos, la producción de alquitranes, la conversión del carbón y la eficiencia en la gasificación. Los alquitranes fueron analizados mediante cromatografía de gases y espectrometría de masas, para conocer y cuantificar sus diferentes componentes. - Determinación de la capacidad adsorbente de carbones activos producidos mediante gasificación, utilizando azul de metileno como adsorbato. Las conclusiones obtenidas permiten considerar la viabilidad técnica de la gasificación de lodos como fuente de energía renovable.

Gasification technology assessment of sterile coal to clean electrical power generation.

Sterile coal is a low-value residue associated to the coal extraction and mining activity. According to the type and origin of the coal bed configuration, sterile coal production can mainly vary on quantity, calorific value and presence of sulphur compounds. In addition, the potential availability of sterile coal within Spain is apparently high and its contribution to the local power generation would be of interest playing a significant role. The proposed study evaluates the availability and deployment of gasification technologies to drive clean electricity generation from waste coal and sterile rock coal, incorporating greenhouse gas emission mitigation systems, like CO2, H2S and NOx removal systems. It establishes the target facility and its conceptual basic design proposal. The syngas obtained after the gasification of sterile coal is processed through specific conditioning units before entering into the combustion chamber of a gas turbine. Flue gas leaving the gas turbine is ducted to a heat recovery steam generation boiler; the steam produced within the boilerdrives a steam turbine. The target facility resembles a singular Integrated Gasification in Combined Cycle (IGCC) power station. The evaluation of the conceptual basic design according to the power output set for a maximum sterile contribution, established that rates over 95% H2S and 90% CO2 removal can be achieved. Noticeable decrease of NOx compounds can be also achieved by the use of commercial technology. A techno-economic approach of the conceptual basic design is made evaluating the integration of potential unitsand their implementation within the target facility aiming toachieve clean power generation. The criterion to be compliant with the most restrictive regulation regarding environmental emissions is setting to carry out this analysis.

Simulation of an Integrated Gasification Combined Cycle with Chemical-Looping Combustion and CO2 sequestration

Chemical-looping combustion allows an integration of CO2 capture in a thermal power plant without energy penalty; secondly, a less exergy destruction in the combustion chemical transformation is achieved, leading to a greater overall thermal efficiency. This paper focus on the study of the energetic performance of this concept of combustion in an integrated gasification combined cycle power plant when synthesis gas is used as fuel for the gas turbines. After thermodynamic modelling and optimization of some cycle parameters, the power plant performance is evaluated under diverse working conditions and compared to a conventional integrated gasification combined cycle with precombustion capture. Energy savings in CO2 capture and storage has been quantified. The overall efficiency increase is found to be significant and even notable, reaching values of around 7%. In order to analyze the influence of syngas composition on the results, different H2-content fuels are considered.

Biomass Gasification in a Fluidized Bed Reactor: Effect of Temperature, Stoichiometric Ratio and Biomass Type

This paper investigates the gasification of two biomass types (pine wood and olive stones) in a laboratory scale bubbling fluidized bed reactor, in order to evaluate comparatively their potential in the production of syngas.

Synthesis gas production from various biomass feedstocks

The decomposition of five different biomass samples was studied in a horizontal laboratory reactor. The samples consisted of esparto grass, straw, Posidonea Oceanic seaweed, waste from urban and agricultural pruning and waste from forest pruning. Both pyrolysis in inert atmosphere and combustion in the presence of oxygen were studied. Different heating rates were used by varying the input speed. Major gas compounds were analyzed. The experimental results show that the amount of CO formed is lower in less dense species. It is also found that there is an increase of hydrocarbons formed at increasing feeding rates, in particular methane, while there is a decrease in the production of hydrogen.

Low metal content Co and Ni alumina supported catalysts for the CO2 reforming of methane

Low metal content Co and Ni alumina supported catalysts (4.0, 2.5 and 1.0 wt% nominal metal content) have been prepared, characterized (by ICP-OES, TEM, TPR-H2 and TPO) and tested for the CO2 reforming of methane. The objective is to optimize the metal loading in order to have a more efficient system. The selected reaction temperature is 973 K, although some tests at higher reaction temperature have been also performed. The results show that the amount of deposited carbon is noticeably lower than that obtained with the Co and Ni reference catalysts (9 wt%), but the CH4 and CO2 conversions are also lower. Among the catalysts tested, the Co(1) catalyst (the value in brackets corresponds to the nominal wt% loading) is deactivated during the first minutes of reaction because CoAl2O4 is formed, while Ni(1) and Co(2.5) catalysts show a high specific activity for methane conversion, a high stability and a very low carbon deposition.

Gas production during the pyrolysis and gasification of biological and physico-chemical sludges from oil refinery

Pyrolysis and gasification of two different sludges coming from a Spanish refinery have been performed at different experimental conditions. A physico-chemical (PC) and a biological (BIO) sludge have been studied. Runs at different heating rates (approx. 4 and 10 K/s) and with different contact time between gases and decomposed sludge have been performed. In general, the ratio H2/CO is higher in pyrolytic runs. The highest ratio is obtained in the pyrolysis at low heating rate and parallel flow, using both sludges. The maximum emission of CO, i.e. the worst combustion conditions, is given in the runs where contact time is minimized and at high heating rates.

Gasification and pyrolysis of Posidonia oceanica in the presence of dolomite

In the present work, a very detailed study of the reforming of syngas produced in the decomposition of Posidonia oceanica is done. The effect of the presence of different amounts of dolomite is analyzed. Also pyrolysis is studied, in nitrogen atmosphere, and gasification in the presence of air, oxygen and different amounts of steam. A detailed discussion on formation and destruction of tars is done. Furthermore, the effect of the heating rate in the decomposition and the residence time of the evolved gases are discussed. Syngas with ratio H2/CO from 0.3 to ca. 3 can be obtained from this interesting material. Marine species (microalgae) are usually studied with the aim of cultivating them for gas or oil production, but in this paper we draw attention to the possibility of using a natural resource with a very small impact in the ecosystem.

Gasification and Pyrolysis of Posidonia oceanica in the Presence of Dolomite

Resumen del póster presentado en Symposium on Renewable Energy and Products from Biomass and Waste, CIUDEN (Cubillos de Sil, León, Spain), 12-13 May 2015