Design of Low Power Multi-Standard Active-RC Filter for WLAN and DVB-H

In this paper, a low-power, highly linear, integrated, active-RC filter exhibiting a multi-standard (IEEE 802.11a/b/g and DVB-H) application and bandwidth (3MHz, 4MHz, 9.5MHz) is present. The filter exploits digitally-controlled polysilicon resister banks and an accurate automatic tuning scheme to account for process and temperature variations. The automatic frequency calibration scheme provides better than 3% corner frequency accuracy. The Butterworth filter is design for receiver (WLAN and DVB-H mode) and transmitter (WLAN mode). The filter dissipation is 3.4 mA in RX mode and 2.3 mA (only for one path) in TX mode from 2.85-V supply. The dissipation of calibration consumes 2mA. The circuit has been fabricated in a 0.35um 47-GHz SiGe BiCMOS technology, the receiver and transmitter occupy 0.28-mm(2) and 0.16-mm(2) (calibration circuit excluded), respectively.

高Tc超导体R_1Ba_2Cu_3O_(2-x)(R-rare earth)的磁性和超异电性研究

本论文合成了R_1Ba_2Cu_3O_(2-x) (R = La、Nd、Sm、Eu、Gd、Dr、Ho、Er、Tm、Yb)、Y_2Ba_2Cu_3O_(2-x) (x = 0.10～1.17)和Y_1Ba_2Cu_3O_(7-x)S_x (x = 0～2)，并对磁性和超导电性进行了较为系统的研究。R_1Ba_2Cu_3O_(2-x)的磁化率在T > Tc的很宽的温度范围内服从Curic-Weiss定律，求得的有效磁矩略大于理论值，差值与Y_1Ba_2Cu_3O_(2-x)中Cu~(2+)磁矩相近，说明Cu~(2+)的磁矩对体系磁性有额外贡献，这贡献随R~(3+)离子中自旋平行的电子权的增多而增大。其高温下的磁化率CT > 700K)相对Curic-Weiss定律发生较大偏离，这偏离可能的来源有三个：高温下稀土离子发生较大的能级反转效应，高温下结构相变对磁性的影响，高温下氧含量减少造成Cu~(2+)磁矩增大。R_1Ba_2Cu_3O_(2-x)磁化率在T < Tc时也服从Curic-Weiss定律，R~(3+)磁矩是定域的，表明超导与磁性相互独立。互不相关，稀土磁矩与传导电子间无相互作用。用Sr取代R_1Ba_2Cu_3O_(2-x)中的Ba，没能使体系产生磁有序的变化，但却使有效磁矩增大，并完全破坏了样品的超导电性。Sm~(3+)磁化率不服从Curic-Weiss定律，在Sm_1Ba_2Cu_3O_(2-x)中Sm~(3+)显示了典型Van VlccK离子的特性。Y_1Ba_2Cu_3O_(2-x)随氧含量减少发生超导体一半导体一绝缘体的转化，当氧含量由6.90减小至6.49时发生由正交到四方的结构相变。当(7-x) = 5.83时有较多杂质相出现，123相开始分解。样品磁化率均服从Curic-Weiss定律，并随氧含量增大磁化率－温度曲线越来越趋于平缓（直线），当(7-x) = 6.90时磁化率基本不随温度变化，这时Pauli顺磁性占主导地位，这说明氧含量增加定域磁矩减少，求得的有效磁矩Peff随氧含量增大总趋势减小。提出了电子“巡游”的观点，较好地解释了上述现象，并推测出Cu(2)的d电子是离域的，对样品磁矩没有贡献，样品Peff来源于部分Cu(1)的定域Cu~(2+)的磁矩，上述推测被EPR结果证实。正交相Y_1Ba_2Cu_3O_(2-x)的EPR谱显示了中心对称成准立方晶场中Cu~(2+)(d~9, S = 1/2, I = 3/2)的EPR物性。而四方相样品的EPR谱却出现了明显的各向异性，说明观察到的为Cu(1)的EPR信号，由Cu(1)~(2+)的写域磁矩产生。Y_1Ba_2Cu_3O_(2-x)的EPR信号束源于本体相，而非Y_2Cu_2O_5、BaCuO_2、Y_2BaCuO_5等杂质相。各样品EPR信号的自旋浓度远小于1spin/cu，并随氧含量减小而增大，当(7-x) = 6.49、6.40时自旋浓度出现陡增，这时伴随由正交到四方的转化，证明了电子“巡游”观点的正确。用硫部分取代Y_1Ba_2Cu_3O_2g中的氧，当Y_1Ba_2Cu_3O_(2-x)Sx中x = 0.11时Tc = 92.6K，比Y_1Ba_2Cu_3O_(7-x)升高2K，但由于杂质相的存在，ΔTc加宽。其他样品多为半导体和绝缘体。硫取代0，当x = 0.04，0.06，0.11和1.20时磁化率服从Curic-Weiss定律，并且x = 0.87，1.2时分别在230K、240K出现反铁磁有序。其他样品由于Cu被还原为＋1价而变成抗磁性。x = 0.11 (Tc = 92.6K)，EPR谱为正交场中Cu~(2+)的信号。自旋浓度与温度无关。当所有Cu均为Cu~(1+)时，测问的是-s-的EPR信号，而Cu为混合价态(+1和+2时)测问是上述两种信号的叠加。

Comparative study on the doping effect of 3d elements in Bi(1.5)Pb(0.2)Sr(2)Ca(2)Cu(2.8)M(0.2)O(y) (M=Sc,Ti,V,Cr,Mn,Fe,Co,Ni, or Zn)

With XRD, R-T, and ac chi measurements a comparative study on the doping effects of 3d elements in Bi(1.5)Pb(0.2)Sr(2)Ca(2)Cu(2.8)M(0.2)O(y) (M = Sc, Ti, V, Cr, Mn, Fe, Co, Ni, or Zn) has been carried out. The effects of the former five members are significantly different, both on phase formed and on T-c, from the latter four. It seems that the effect on phase stabilization correlates with the valency of the doped cation. In connection with the instability of the 2223 phase, the correlation has been discussed.

LUMINESCENCE OF BI(3+) AND THE ENERGY-TRANSFER FROM BI(3+) TO R(3+) (R=EU,DY,SM,TB) IN ALKALINE-EARTH BORATES

At room temperature, the Bi3+ ion shows broad band characters of its luminescence in Ca2B2O5, M3B2O6 ( M=Ca,Sr ) and SrB4O7. The maxima of the Bi3+ S-1(0)-->P-3(1) absorption bands are located in the range of 240-300nm, but the energy variation of the corresponding P-3(1)-->S-1(0) emissions is very large. The maxima of these emission bands change from 350nm in Ca3B2O6;Bi3+ to 586nm in SrB4O7:Bi3+. The Stokes shift of the Bi3+ luminescence increases from 6118 cm-1, in Ca2B2O5:Bi3+, to 24439 cm-1, in SrB4O7:Bi3+. The emission intensity of the Bi3+ luminescence increases with the decreasing Stokes shift. It has been found that in Ca2B2O5, the Bi3+ ion could transfer its excitation energy to the R3+ ions ( R=Eu, Dy, Sm, Tb ) , but in, Ca3B2O6 and Sr3B2O6, only Bi3+-->Eu3+ was observed. No energy transfer from Bi3+ to R3+ was detected in SrB4O7.

湘中锡矿山锑矿床的Sr同位素地球化学

对湘中锡矿山锑矿床围岩灰岩、硅化灰岩、煌斑岩和脉石矿物进行了系统的Sr同位素研究。结果表明，矿区围岩发生了隐性蚀变，灰岩中Sr亏损，而^87Sr/^86Sr高于同时代的海相碳酸盐，这种隐性蚀变很可能是水／岩反应所致。矿体附近的硅化灰岩中Sr更加亏损，而^87Sr/^86Sr明显增加。成矿期方解石的^87Sr/^86Sr较高，成矿体系中变化的W／R比造成了方解石中^87Sr/^86Sr值的明显波动。成矿流体为一富放射成因^87Sr的溶液。成矿流体来自或流经基底地层，流体中的Sr由基底碎屑岩提供，矿质Sb也可能主要来自富Sb的元古宇基底。水／岩反应的理论模拟显示，锡矿山成矿流体中的Sr约为3．0μg/g，^87Sr/^86Sr为０．７１７；蚀变－成矿体系为一开放体系，矿石的沉淀机制主要为水／岩反应，成矿体系中W／R 比较高。

Characteristics of the interfacial capacitance in thin film Ba0.5Sr0.5TiO3 capacitors with SrRuO3 and (La, Sr)CoO3 bottom electrodes

Thin film Ba0.5Sr0.5TiO3 (BST) capacitors of thickness similar to75 nm to similar to1200 nm, with Au top electrodes and SrRuO 3 (SRO) or (La, Sr)CoO3 (LSCO) bottom electrodes were fabricated using Pulsed Laser Deposition. Implementing the "series capacitor model," bulk and interfacial capacitance properties were extracted as a function of temperature and frequency. 'Bulk' properties demonstrated typical ceramic behaviour, displaying little frequency dependence and a permittivity and loss peak at 250 K and 150 K respectively. The interfacial component was found to be relatively temperature and frequency independent for the LSCO/BST capacitors, but for the SRO/BST configuration the interfacial capacitance demonstrated moderate frequency and little temperature dependence below T similar to 300 K but a relatively strong frequency and temperature dependence above T similar to3 00 K. This was attributed to the thermal activation of a space charge component combined with a thermally independent background. The activation energy for the space charge was found to be E-A similar to 0.6 eV suggesting de-trapping of electrons from shallow level traps associated with a thin interfacial layer of oxygen vacancies, parallel to the electrodes.

Effect of corrosion of reinforcement on the mechanical behaviour of highly corroded RC beams

This paper describes an experimental investigation of the behaviour of corroded reinforced concrete beams. These have been stored in a chloride environment for a period of 26 years under service loading so as to be representative of real structural and environmental conditions. The configuration and the widths of the cracks in the two seriously corroded short-span beams were depicted carefully, and then the beams were tested until failure by a three-point loading system. Another two beams of the same age but without corrosion were also tested as control specimens. A short span arrangement was chosen to investigate any effect of a reduction in the area and bond strength of the reinforcement on shear capacity. The relationship of load and deflection was recorded so as to better understand the mechanical behaviour of the corroded beams, together with the slip of the tensile bars. The corrosion maps and the loss of area of the tensile bars were also described after having extracted the corroded bars from the concrete beams. Tensile tests of the main longitudinal bars were also carried out. The residual mechanical behaviour of the beams is discussed in terms of the experimental results and the cracking maps. The results show that the corrosion of the reinforcement in the beams induced by chloride has a very important effect on the mechanical behaviour of the short-span beams, as loss of cross-sectional area and bond strength have a very significant effect on the bending capacity.

Regulation of OPA1-mediated mitochondrial fusion by leucine zipper/EF-hand-containing transmembrane protein-1 plays a role in apoptosis

Carboxyl-terminal modulator protein (CTMP) is a tumor suppressor-like binding partner of Protein kinase B (PKB/Akt) that negative regulates this kinase. In the course of our recent work, we identified that CTMP is consistently associated with leucine zipper/EF-hand-containing transmembrane-1 (LETM1). Here, we report that adenovirus-LETM1 increased the sensitivity of HeLa cells to apoptosis, induced by either staurosporine or actinomycin D. As shown previously, LETM1 localized to the inner mitochondrial membrane. Electron-microscopy analysis of adenovirus-LETM1 transduced cells revealed that mitochondrial cristae were swollen in these cells, a phenotype similar to that observed in optic atrophy type-1 (OPA1)-ablated cells. OPA1 cleavage was increased in LETM1-overexpressing cells, and this phenotype was reversed by overexpression of OPA1 variant-7, a cleavage resistant form of OPA1. Taken together, these data suggest that LETM1 is a novel binding partner for CTMP that may play an important role in mitochondrial fragmentation via OPA1-cleavage. (C) 2009 Elsevier Inc. All rights reserved

FhCaBP4: A Fasciola hepatica calcium binding protein with EF-hand and dynein light chain domains

In trematodes, there is a family of proteins which combine EF-hand-containing domains with dynein light chain (DLC)-like domains. A member of this family from the liver fluke, Fasciola hepatica-FhCaBP4-has been identified and characterised biochemically. FhCaBP4 has an N-terminal domain containing two imperfect EF-hand sequences and a C-terminal dynein light chain-like domain. Molecular modelling predicted that the two domains are joined by a flexible linker. Native gel electrophoresis demonstrated that FhCaBP4 binds to calcium, manganese, barium and strontium ions, but not to magnesium or zinc ions. The hydrophobic, fluorescent probe 8-anilinonaphthalene-1-sulphonate bound more tightly to FhCaBP4 in the presence of calcium ions. This suggests that the protein undergoes a conformational change on ion binding which increases the number of non-polar residues on the surface. FhCaBP4 was protected from limited proteolysis by the calmodulin antagonist W7, but not by trifluoperazine or praziquantel. Protein-protein cross-linking experiments showed that FhCaBP4 underwent calcium ion-dependent dimerisation. Since DLCs are commonly dimeric, it is likely that FhCaBP4 dimerises through this domain. The molecular model reveals that the calcium ion-binding site is located close to a key sequence in the DLC-like domain, suggesting a plausible mechanism for calcium-dependent dimerisation.

Sr-Nd-Pb Isotope Evidence for Ice-Sheet Presence on Southern Greenland During the Last Interglacial

To ascertain the response of the southern Greenland Ice Sheet (GIS) to a boreal summer climate warmer than at present, we explored whether southern Greenland was deglaciated during the Last Interglacial (LIG), using the Sr-Nd-Pb isotope ratios of silt-sized sediment discharged from southern Greenland. Our isotope data indicate that no single southern Greenland geologic terrane was completely deglaciated during the LIG, similar to the Holocene. Differences in sediment sources during the LIG relative to the early Holocene denote, however, greater southern GIS retreat during the LIG. These results allow the evaluation of a suite of GIS models and are consistent with a GIS contribution of 1.6 to 2.2 meters to the =4-meter LIG sea-level highstand, requiring a significant sea-level contribution from the Antarctic Ice Sheet.

Flexural behaviour of external R/C steel fibre reinforced beam-column joints

A softened strut-and-tie macro model able to reproduce the flexural behaviour of
external beam-column joint is presented. The model is specific for concrete with hooked steel fibres (FRC) and it is designed to calculate the flexural response, as load-deflection curve, of a beam-column sub-assemblages. The model considers the presence of a constant vertical load acting on the column and of a monotonically increasing lateral force applied at the tip of the beam.

Epitaxial ferroelectric Pb(Mg1/3Nb2/3)O3-PbTiO3 thin films on La0.7Sr0.3MnO3 bottom electrode

Epitaxial (001)-oriented 0.7Pb(Mg_0.33Nb_0.67)O₃-0.3PbTiO₃ (PMN-PT) thin films were deposited by pulsed laser deposition on vicinal SrTiO₃ (001) substrates using La_0.7Sr_0.3MnO₃ as bottom electrode. Detailed microstructural investigations of these films were carried out using X-ray diffraction (XRD), atomic force microscopy (AFM) and transmission electron microscopy (TEM). Polarization-field hysteresis curves were measured at room temperature. Spontaneous polarization P s , remnant polarization P r and coercive voltage V c were found to be 25 μC/cm², 15 μC/cm² and 0.81 V, respectively. Field dependent dielectric constant measurements exhibited butterfly shaped curves, indicating the true ferroelectric nature of these films at room temperature. The dielectric constant and the dielectric loss at 100 kHz were found to be 238 and 0.14, respectively. The local piezoelectric properties of PMN-PT films were investigated by piezoelectric force microscopy and were found to exhibit a local piezoelectric coefficient of 7.8 pm/V.