减压直流等离子体射流电子温度的双静电探针测量

建立了一套双静电探针诊断系统,用于检测在气流量为4.2 slm、弧电流为80 A、真空事压力为165Pa的条件下纯氩直流非转移弧等离子体射流的电子温度及其分布.结果表明:发生器出口处射流中心的电子温度约为14 500 K,射流中电子温度随离开发生器出口的轴向或径向距离的增加而单调降低;径向电子温度梯度约为263 K/mm,轴向电子温度梯度为69 K/mm;射流中电子温度随弧电流增加而单调上升.

Coherent enhancement of broadband frequency up-conversion in BBO crystal by shaping femtosecond laser pulses

An optimal feedback control of broadband frequency up-conversion in BBO crystal is experimentally demonstrated by shaping femto-second laser pulses based on genetic algorithm, and the frequency up-conversion efficiency can be enhanced by similar to 16%. SPIDER results show that the optimal laser pulses have shorter pulse-width with the little negative chirp than the original pulse with the little positive chirp. By modulating the fundamental spectral phase with periodic square distribution on SLM-256, the frequency up-conversion can be effectively controlled by the factor of about 17%. The experimental results indicate that the broadband frequency up-conversion efficiency is related to both of second harmonic generation (SHG) and sum frequency generation (SFG), where the former depends on the fundamental pulse intensity, and the latter depends on not only the fundamental pulse intensity but also the fundamental pulse spectral phase. (c) 2006 Elsevier B.V. All rights reserved.

一种新型结构的单纵模光纤激光器

单纵模掺铒光纤激光器在光通信和光传感等方面有着广泛的应用前景。设计了一种新型的光纤激光器，在光纤环形镜中嵌入未抽运的掺铒光纤作为可饱和吸收体以抑制多纵模，用光纤环谐振腔作为滤波器抑制拍频噪声，用光纤光栅作为波长选择器件，最终得到了单纵模输出并消除了拍频噪声。使用零拍法测量其线宽小于频谱仪的低频极限5kHz。实验结果证明了可饱和吸收体和光纤环的功能。

Influences of phase shift on superresolution performances of annular filters

This paper investigates the influences of phase shift on superresolution performances of annular filters. Firstly, it investigates the influence of phase shift on axial superresolution. It proves theoretically that axial superresolution can not be obtained by two-zone phase filter with phase shift pi, and it gets the phase shift with which axial superresolution can be brought by two-zone phase filter. Secondly, it studies the influence of phase shift on transverse superresolution. It finds that the three-zone phase filter with arbitrary phase shift has an almost equal optimal transverse gain to that of commonly used three-zone phase filter, but can produce a much higher axial superresolution gain. Thirdly, it investigates the influence of phase shift on three-dimensional superresolution. Three-dimensional superresolution capability and design margin of three-zone complex filter with arbitrary phase shift are obtained, which presents the theoretical basis for three-dimensional superresolution design. Finally, it investigates the influence of phase shift on focal shift. To obtain desired focal shifts, it designs a series of three-zone phase filters with different phase shifts. A spatial light modulator (SLM) is used to implement the designed filters. By regulating the voltage imposed on the SLM, an accurate focal shift control is obtained.

A Q-swicthed all-solid-state single-longitudinal-mode laser with adjustable pulse-width and high repetition rate

A single-longitudinal-mode (SLM) laser-diode pumped Nd: YAG laser with adjustable pulse width is developed by using the techniques of pre-lasing and changing polarization of birefingent crystal. The Q-switching voltage is triggered by the peak of the pre-lasing pulse to achieve the higher stability of output pulse energy. The output energy of more than 1 mJ is obtained with output energy stability of 3% (rms) at 100 Hz. The pulse-width can be adjusted from 30 ns to 300 ns by changing the Q-switching voltage. The probability of putting out single-longitudinal-mode pulses is almost 100%. The laser can be run over four hours continually without mode hopping.

A compact diode-pumped injection seeded Nd : YAG laser with resonance-detection technique

A diode pumped injection seeded single-longitudinal-mode (SLM) Nd:YAG laser is achieved by using the resonance-detection technique in Q-switching operation. The pulsed oscillator laser uses a folded cavity to achieve compact construction. This system operates at 100 Hz and provides over 20 mJ/pulse of single-frequency 1064 nm output. The M-2 values of horizontal and vertical axes are 1.58 and 1.41, respectively. The probability of putting out single-longitudinal-mode pulses is 100%. The 355 nm laser output produced by frequency tripling has a linewidth less than 200 MHz. The laser can run over eight hours continually without mode hopping.

马铃薯in vitro 块茎发育的研究及其遗传转化受体系统的建立

研究了BAP在SLM→TIM、MA→TIM和切段诱导系统中与in vitro块茎发育的关系。在SLM→TIM系统中BAP没有促进块茎发育的作用;在MA→TIM系统中BAP具有促进块茎发育的作用;切段培养在20 ℃、8小时光照条件下则其块茎发育对BAP有依赖。系统地研究了光周期、蔗糖浓度和外源细胞分裂素在促进切段块茎发育方面的作用及其交互影响。确定了由切段诱导块茎的最佳培养条件以及用于BAP吸收代谢研究的实验条件。讨论了切段诱导系统在理论研究上的价值和生产上应用的前景。研究了无菌苗、长切段及切段BAP吸收运转代谢特点及其与块茎发育关系。马铃薯植物系统对BAP的吸收运转是需能代谢过程。BAP在植物系统运转性差与其在组织的代谢特点有关。在块茎诱导早期有标物质在小块茎或匍匐茎末端积累，这可能促使细胞分裂从而诱发块茎发育;但在成熟块茎中放射性物质浓度很低。外源细胞分裂素在切段或匍匐茎局部积累不是块茎发育的充分条件。在有利于块茎发育的条件下代谢早期BAP活性代谢产物含量明显地高于对照，代谢一定阶段后二种处理的切段BAP代谢谱趋于接近，这一代谢特点与BAP促进块茎发育的生理效应有关。运用同位素示踪技术研究了切段蔗糖吸收特点，外源细胞分裂素促进蔗糖在切段系统积累从而诱导体细胞储藏组织生化分化。短日照（黑暗）、较高浓度蔗糖、合适浓度BAP都有促进离体切段块茎发育作用，这几个因子在提高切段诱导水平方面具有协同效应。诱导早期切段中有块茎专一性糖蛋白Patatin痕量的存在。当切段发育了较大块茎后（诱导约15天）切段中Patatin含量明显增加。诱导3天切段系统中即有Patatin mRNA高水平地转录。诱导7天阶段Patatin mRNA含量迅速下降。块茎发育很可能是通过几种激素（包括块茎诱导因子）协同地对植物系统同化物尤其是蔗糖源库关系的调节而实现的。 建立了向马铃薯植物引入外源基因的受体系统。叶园盘与农杆菌（pGV2260:: pGV941）共培养。转化植株在选择培养基上培养大约3周即可从愈伤组织或直接从叶片边缘产生。在含有高浓度卡那霉素的培养基上转化植株大多表型正常，切段能够发育块茎，叶片能够形成愈伤组织。转化再生植株均含有NPT－II活性而未转化Desiree无菌苗没有NPT－II活性。Southern分析表明NPT－II基因已整合入转化植物基因组中。这一实验系统的建立为向马铃薯植物引进具有重要经济价值的外源基因创造了条件。

Compact holographic optical interconnections using nematic liquid crystal spatial light modulators

In a fibre-optic communication network, the wavelength-division multiplexing (WDM) technique enables an expansion of the data-carrying capacity of optical fibres. This can be achieved by transmitting different channels on a single optical fibre, with each channel modulating a different wavelength. In order to access and manipulate these channels at a node of the network, a compact holographic optical switch is designed, modelled, and constructed. The structure of such a switch consists of a series of optical components which are used to collimate the beam from the input, de-multiplex each individual wavelength into separated channels, manipulate the separated channels, and reshape the beam to the output. A spatial light modulator (SLM) is crucial in this system, offering control and flexibility at the channel manipulation stage, and providing the ability to redirect light into the desired output fibre. This is achieved by the use of a 2-D analogue phase computer generated hologram (CGH) based on liquid crystal on silicon (LCOS) technology. © 2011 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

Ferroelectric liquid crystal over silicon devices

Over the past 20 years, ferroelectric liquid crystal over silicon (FLCOS) devices have made a wide impact on applications as diverse as optical correlation and holographic projection. To cover the entire gamut of this technology would be difficult and long winded; hence, this paper describes the significant developments of FLCOS within the Engineering Department at the University of Cambridge.The purpose of this paper is to highlight the key issues in fabricating silicon backplane spatial light modulators (SLMs) and to indicate ways in which the technology can be fabricated using cheap, low-density production and manufacturability. Three main devices have been fabricated as part of several research programmes and are documented in this paper. The fast bitplane SLM and the reconfigurable optical switches for aerospace and telecommunications systems (ROSES) SLM will form the basis of a case study to outline the overall processes involved. There is a great deal of commonality in the fabrication processes for all three devices, which indicates their potential strength and demonstrates that these processes can be made independent of the SLMs that are being assembled. What is described is a generic process that can be applied to any silicon backplane SLM on a die-by-die basis. There are hundreds of factors that can affect the yield in a manufacturing process and the purpose of a good process design procedure is to minimise these factors. One of the most important features in designing a process is fabrication experience, as so many of the lessons in this business can only be learned this way. We are working with the advantage of knowing the mistakes already made in the flat panel display industry, but we are also faced with the fact that those mistakes took many years and many millions of dollars to make.The fabrication process developed here originates and adapts earlier processes from various groups around the world. There are also a few totally new processes that have now been adopted by others in the field. Many, such as the gluing process, are still on-going and have to be worked on more before they will fully suit 'manufacturability'. © 2012 Copyright Taylor and Francis Group, LLC.

Characterization of multimode fiber by selective mode excitation

Each mode of a 2 km 50 μ OM2 grade multimode fiber is precisely excited at multiple orientations using a binary phase spatial light modulator (SLM) to generate a detailed modal description of the fiber and minimize modal dispersion over 4.5 THz of optical bandwidth. © 2012 IEEE.

Application of the fractional Fourier transform to the design of LCOS based optical interconnects and fiber switches

It is shown that reflective liquid crystal on silicon (LCOS) spatial light modulator (SLM) based interconnects or fiber switches that use defocus to reduce crosstalk can be evaluated and optimized using a fractional Fourier transform if certain optical symmetry conditions are met. Theoretically the maximum allowable linear hologram phase error compared to a Fourier switch is increased by a factor of six before the target crosstalk for telecom applications of -40 dB is exceeded. A Gerchberg-Saxton algorithm incorporating a fractional Fourier transform modified for use with a reflective LCOS SLM is used to optimize multi-casting holograms in a prototype telecom switch. Experiments are in close agreement to predicted performance. © 2012 Optical Society of America.

The development of a scanning strategy for the manufacture of porous biomaterials by selective laser melting.

Porous structures are used in orthopaedics to promote biological fixation between metal implant and host bone. In order to achieve rapid and high volumes of bone ingrowth the structures must be manufactured from a biocompatible material and possess high interconnected porosities, pore sizes between 100 and 700 microm and mechanical strengths that withstand the anticipated biomechanical loads. The challenge is to develop a manufacturing process that can cost effectively produce structures that meet these requirements. The research presented in this paper describes the development of a 'beam overlap' technique for manufacturing porous structures in commercially pure titanium using the Selective Laser Melting (SLM) rapid manufacturing technique. A candidate bone ingrowth structure (71% porosity, 440 microm mean pore diameter and 70 MPa compression strength) was produced and used to manufacture a final shape orthopaedic component. These results suggest that SLM beam overlap is a promising technique for manufacturing final shape functional bone ingrowth materials.

The foundations of a new approach to additive manufacturing: Characteristics of free space metal deposition

In this paper, we report on the realisation of a free space deposition process (FSD). For the first time the use of a moving support structure to deposit tracks of metal starting from a substrate and extending into free space is characterised. The ability to write metal shapes in free space has wide ranging applications in additive manufacturing and rapid prototyping where the tracks can be layered to build overhanging features without the use of fixed support structures (such as is used in selective laser melting (SLM) and stereo lithography (SLA)). We demonstrate and perform a preliminary characterisation of the process in which a soldering iron was used to deposit lead free solder tracks. The factors affecting the stability of tracks and the effect of operating parameters, temperature, velocity, initial track starting diameter and starting volume were measured. A series of 10 tracks at each setting were compared with a control group of tracks; the track width, taper and variation between tracks were compared. Notable results in free space track deposition were that the initial track diameter and volume affected the repeatability and quality of tracks. The standard deviation of mean track width of tracks from the constrained initial diameter group were half that of the unconstrained group. The amount of material fed to the soldering iron before commencing deposition affected the taper of tracks. At an initial volume of 7 mm3 and an initial track diameter of 0.8 mm, none of the ten tracks deposited broke or showed taper > ∼1°. The maximum deposition velocity for free space track deposition using lead-free solder was limited to 1.5 mm s-1. © 2011 Elsevier B.V. All rights reserved.

Mode division multiplexing of modes with the same azimuthal index

The design of an SLM-based mode demultiplexer is discussed and mode division multiplexing is performed using the LP0,1 and LP 0,2 modes, representing the first demonstration to propagate channels on modes with the same azimuthal index. Mode multiplexed transmission over 2 km of 50-μm OM2 fiber demonstrates a modal selectivity of 16 dB and an OSNR penalty of 1.5 dB for the transmission of 2×56 Gb/s QPSK signals. © 2012 IEEE.

A critical analysis of loudness calculation methods

The physical meaning and calculation procedures for determining loudness was critically analyzed. Four noise sources were used in comparing the software packages dBFA dBSonic, which were used in the investigation to a public domain code. The purpose of the comparison was to evaluate the validity of the results obtained and to gain an idea of the shortcomings of the relevant standards. A comparison of the results for loudness was computed from various methods, used in the study. Two basic sources of input data such as a sound level meter (SLM) and a 01 dB data acquisition system (DAQ), were available for the comparison. The SLM directly gave 1/3 octave band levels, while the data from the DAQ was filtered to give the results. Five processing methods, including a Visual Basic (VB) program and a VB program adapted from dBFA, were used for the study. It was found that the calculation of loudness from 1/3 octave cannot be separated from the filtering process.