Strength properties of composite clay balls containing additives from industry wastes as new filter media in water treatment

Pebble matrix filtration (PMF) is a water treatment technology that can remove suspended solids in highly turbid surface water during heavy storms. PMF typically uses sand and natural pebbles as filter media. Hand-made clay pebbles (balls) can be used as alternatives to natural pebbles in PMF treatment plants, where natural pebbles are not readily available. Since the high turbidity is a seasonal problem that occurs during heavy rains, the use of newly developed composite clay balls instead of pure clay balls have the advantage of removing other pollutants such as natural organic matter (NOM) during other times. Only the strength properties of composite clay balls are described here as the pollutant removal is beyond the scope of this paper. These new composite clay balls must be able to withstand dead and live loads under dry and saturated conditions in a filter assembly. Absence of a standard ball preparation process and expected strength properties of composite clay balls were the main reasons behind the present study. Five different raw materials from industry wastes: Red Mud (RM), Water Treatment Alum Sludge (S), Shredded Paper (SP), Saw Dust (SD), and Sugar Mulch (SM) were added to common clay brick mix (BM) in different proportions. In an effort to minimize costs, in this study clay balls were fired to 1100 0C at a local brick factory together with their bricks. A comprehensive experimental program was performed to evaluate crushing strength of composite hand-made clay balls, using uniaxial compression test to establish the best material combination on the basis of strength properties for designing sustainable filter media for water treatment plants. Performance at both construction and operating stages were considered by analyzing both strength properties under fully dry conditions and strength degradation after saturation in a water bath. The BM-75% as the main component produced optimum combination in terms of workability and strength. With the material combination of BM-75% and additives-25%, the use of Red Mud and water treatment sludge as additives produced the highest and lowest strength of composite clay balls, with a failure load of 5.4 kN and 1.4 kN respectively. However, this lower value of 1.4 kN is much higher than the effective load on each clay ball of 0.04 kN in a typical filter assembly (safety factor of 35), therefore, can still be used as a suitable filter material for enhanced pollutant removal.

Determinants of trade in recyclable wastes: Evidence from commodity-based trade of waste and scrap

This paper examines factors that affect the trade of recyclable waste in both exporting and importing countries. To this end, we employ two important elements: first, we adopt a gravity model in our empirical methodology; second, we select five waste and scrap commodities and undertake estimations using commodity-level trade data. We demonstrate that, the higher the wage/per capita GDP/population of an importing country, the more recyclable wastes it imports. This result suggests that the demand for final goods and, accordingly, the demand for materials including recycled material, have strong effects on the import volume of recyclable waste. Moreover, this implies that the imports of a developing country from developed countries increase with expanding industrial activity and economic growth. We find no evidence for a pollution haven for wastes and recycling.

Influence of kaolinite particle size on cross-link density, microstructure and mechanical properties of latex blending styrene butadiene rubber composites

Cross-link density, microstructure and mechanical properties of styrene butadiene rubber (SBR) composites filled with different particle sized kaolinites are investigated. With the increase of kaolinite particle size, the cross-link density of the filled SBR composites, the dispersibility and orientation degree of kaolinite particles gradually decrease. Some big cracks in filled rubber composites are distributed along the fringe of kaolinite aggregates, and the absorbance of all the absorption bands of kaolinites gradually increase with the increase of kaolinite particle size. All mechanical property indexes of kaolinite filled SBR composites decrease due to the decrease of cross-linking and reduction of interface interaction between filler and rubber matrix.

Light scattering studies on solutions of chlorinated rubber

Measurements have been made of the depolarisation factors \sigma u ,\sigma v ,\sigma h, and the intensity of scattering in the horizontal transverse direction, in the case of solutions of four different samples of chlorinated rubber in carbon tetrachloride. The size, shape and molecular weight of the micelles have been deduced by the application of the light scattering theories of Gans, Vrklajan and Katalinic and Debye. The extent to which the degradation of the rubber molecule occurs on chlorination has also been assessed.

Studies on the Tracking and Erosion Resistance of RTV Silicone Rubber Nanocomposite

One of the problems associated with outdoor polymeric insulators is tracking and erosion of the weathershed which can directly influence the reliability of the power system. Flame retardants are added to the base material to enhance its tracking and erosion resistance. Hydroxide fillers are regarded as the best flame retardants. This paper deals with studies related to nano - sized magnesium dihydroxide (MDH) and micron-sized Alumina Trihydrate (ATH) fillers as flame retardants in RTV silicone rubber. Tracking and erosion resistance studies were carried out on MDH and ATH silicone rubber composites using an inclined plane tracking and erosion (IPT) resistance tester. The MDH filled (5% by wt) composites performed much better than ATH composites in terms of eroded mass, depth of erosion, width and length of erosion. The eroded mass of MDH composite is 49.8 % that of ATH composite which can be attributed to high surface area and higher thermal stability of MDH nanofillers.

Effect of microwave radiation on seed mortality of rubber vine (Cryptostegia grandiflora R.Br.), parthenium (Parthenium hysterophorous L.) and bellyache bush (Jatropha gossypiifolia L.)

A trial was undertaken to evaluate the effect of microwaves on seed mortality of three weed species. Seeds of rubber vine (Cryptostegia grandiflora R.Br.), parthenium (Parthenium hysterophorous L.) and bellyache bush (Jatropha gossypiifolia L.) were buried at six depths (0, 2.5, 5, 10, 20 and 40 cm) in coarse sand maintained at one of two moisture levels, oven dry or wet (field capacity), and then subjected to one of five microwave radiation durations of (0, 2, 4, 8 and 16 min). Significant interactions between soil moisture level, microwave radiation duration, seed burial depth and species were detected for mortality of seeds of all three species. Maximum seed mortality of rubber vine (88%), parthenium (67%) and bellyache bush (94%) occurred in wet soil irradiated for 16 min. Maximum seed mortality of rubber vine and bellyache bush seeds occurred in seeds buried at 2.5 cm depth whereas that of parthenium occurred in seeds buried at 10 cm depth. Maximum soil temperatures of 114.1 and 87.5°C in dry and wet soil respectively occurred at 2.5 cm depth following 16 min irradiation. Irrespective of the greater soil temperatures recorded in dry soil, irradiating seeds in wet soil generally increased seed mortality 2.9-fold compared with dry soil. Moisture content of wet soil averaged 5.7% compared with 0.1% for dry soil. Results suggest that microwave radiation has the potential to kill seeds located in the soil seed bank. However, many factors, including weed species susceptibility, determine the effectiveness of microwave radiation on buried seeds. Microwave radiation may be an alternative to conventional methods at rapidly depleting soil seed banks in the field, particularly in relatively wet soils that contain long lived weed seeds.

Predicting wood value in Queensland Caribbean pine plantations using a decision support system

A decision support system has been developed in Queensland to evaluate how changes in silvicultural regimes affect wood quality, and specifically the graded recovery of structural timber. Models of tree growth, branch architecture and wood properties were developed from data collected in routine Caribbean pine plantations and specific silvicultural experiments. These models were incorporated in software that simulates the conversion of standing trees into logs, and the logs into boards, and generates detailed data on knot location and basic density distribution. The structural grade of each board was determined by simulating the machine stress-grading process, and the predicted graded recovery provided an indicator of wood value. The decision support system improves the basis of decision-making by simulating the performance of elite genetic material under specified silvicultural regimes and by predicting links between wood quality and general stand attributes such as stocking and length of rotation.

Field assessment of the resistance of timber products to termite (Isoptera) damage: Results can change with the amount of bait wood

Whether or not termites initiate damage to timber via the end grain may determine the need for spot-treating the exposed untreated cut ends of envelope-treated softwood framing material. Australian Coptotermes acinaciformis (Froggatt) were field-tested for their ability to initiate feeding via the end grain of timber (35 × 90 mm) treated with a repellent Tanalith® T envelope. Specimens of commercial radiata pine Pinus radiata D.Don framing timber (untreated) and slash pine Pinus elliottii Englem. (untreated and envelope-treated) were partially clad in fine stainless steel mesh. Clad and unclad specimens were exposed to C. acinaciformis near Townsville, North Queensland, Australia, for four months. Results showed that this species of termite can indeed damage timber via the end grain, including exposed untreated cut ends of envelope-treated material as demonstrated earlier for different populations of C. acinaciformis. Differences between the test conditions in field trials carried out at different times (where C. acinaciformis either did or did not damage timber via the end grain) are discussed. Clearly, outcomes from field studies with preservative-treated materials are dependent upon experimental conditions. Notably, the amount of bait wood (highly termite-susceptible timber substrate) offered in a given method can strongly influence the termite response. Further investigation is required to standardise this aspect of conditions in protocols for the assessment of wood preservatives.

Quantitative assessment of total phenol contents of European oak (Quercus petraea and Quercus robur) by diffuse reflectance NIR spectroscopy on solid wood surfaces

Near infrared spectroscopy (NIRS) combined with multivariate analysis techniques was applied to assess phenol content of European oak. NIRS data were firstly collected directly from solid heartwood surfaces: in doing so, the spectra were recorded separately from the longitudinal radial and the transverse section surfaces by diffuse reflectance. The spectral data were then pretreated by several pre-processing procedures, such as multiplicative scatter correction, first derivative, second derivative and standard normal variate. The tannin contents of sawmill collected from the longitudinal radial and transverse section surfaces were determined by quantitative extraction with water/methanol (1:4, by vol). Then, total phenol contents in tannin extracts were measured by the Folin-Ciocalteu method. The NIR data were correlated against the Folin-Ciocalteu results. Calibration models built with partial least squares regression displayed strong correlation - as expressed by high determination correlation coefficient (r2) and high ratio of performance to deviation (RPD) - between measured and predicted total phenols content, and weak calibration and prediction errors (RMSEC, RMSEP). The best calibration was provided with second derivative spectra (r2 value of 0.93 for the longitudinal radial plane and of 0.91 for the transverse section plane). This study illustrates that the NIRS technique when used in conjunction with multivariate analysis could provide reliable, quick and non-destructive assessment of European oak heartwood extractives.

Interactions between butterfly pea (Clitoria ternatea) and rubber vine (Cryptostegia grandiflora)

The arutors studied the impact of a forage legume, butterfly pea, on rubber vine at the early establishment phase under seven planting combinations at three nitrogen fertiliser levels. In pure stands, both species increased their shoot and root dry weight yield in response to nitrogen but rubber vine exhibited the greater response. In mixed stands, rubber vine and butterfly pea did not compete with each other at any nitrogen level. An over-yielding response resulted in all mixture combinations in terms of shoot and root yields. Total shoot and root mass of mixed stands significantly out-yielded their highest yielding pure stands by 8% and 27% respectively, suggesting that butterfly pea not only failed to reduce shoot and root growth of rubber vine, but actually improved its growth performance. Consequently, the introduction of butterfly pea to suppress rubber vine is not warranted.

Potential for using through-boring to improve groundline treatment of Australian wood species: A preliminary study.

An aging electricity distribution system and reduced availability of naturally durable tropical hardwoods in Australia will combine in the next decade to produce a major shortage of poles. One approach to mitigating this shortage is to utilize lower durability species and improve the penetration of preservatives into the refractory heartwood by introducing additional pretreatment processes. A potential method for improving preservative penetration in the critical ground-line zone is through-boring. This process, in which holes are drilled through the pole perpendicular to the grain in the ground-line zone, is widely used in the western United States for treatment of Douglas-fir and may be Suitable for many Australian wood species. The potential for improving heartwood penetration in eucalypts with alkaline-copper-quaternary (ACQ) compound was assessed on heartwood specimens from four species (Eucalyptus cloeziana F.Muell., E. grandis W.Hill ex Maiden, E. obliqua L'Her. and E. pellita F.Muell.) and Lophostemon confertus (R.Br.) Peter G.Wilson & J.T.Wateril). Longitudinal ACQ penetration was extremely shallow in L. confertus and only slightly better in E. cloeziana. Longitudinal penetration was good in both E. obliqua and E. pellita, although there was some variation in treatment results with length of pressure period. The results suggest that through-boring might be a reasonable approach for achieving heartwood penetration in some Eucalyptus species, although further studies are required to assess additional treatment schedules and to determine the effects of the process oil flexural properties of the poles.

Improved termite resistance of wood by wax impregnation.

We investigated the effect of wax-treated and biocide-free wood specimens against three different termite species. A laboratory no-choice test with Reticulitermes banyulensis Clément was carried out in Valencia (Spain) under Mediterranean conditions for eight weeks. Scots pine sapwood (Pinus sylvestris L.) fully impregnated with distinct waxes was used. Two field trials were conducted with Coptotermes acinaciformis (Froggatt) and Mastotermes darwiniensis Froggatt in northern Queensland (Australia) with wax-impregnated beech (Fagus sylvatica L.) for 16 weeks. All three subterranean termites are of major economic importance in their respective regions. The results indicated that feeding pressure by the termites was sufficient within all trials for a valid test. Wax-impregnated Scots pine sapwood was classified as durable. No termites survived the test. The results showed an aging process under submersion conditions, which lead to a classification of moderately durable. The paraffin treatment showed good termite resistance under both test procedures, and was classified as durable. The Australian field trials showed a decreased mass loss of wax-treated beech, in which an amide wax showed excellent termite resistance. The results indicate a clear dependence of the termite resistance on the type and ratio of wax used and the feeding preferences of the specific termite species.

Wood properties and knot occlusion of plantation grown Eucalyptus dunnii and Corymbia citriodora subsp. variegata in a pruning and thinning experiment.

A 2 × 2 factorial combination of thinned or unthinned, and pruned or unpruned 11-year-old Eucalyptus dunnii (DWG) and 12-year-old Corymbia citriodora subsp. variegata (CCV) was destructively sampled to provide 60 trees in total per species. Two 1.4 m long billets were cut from each tree and were rotary veneered in a spindleless lathe down to a 45 mm diameter core to expose knots which were classified as either alive, partially occluded or fully occluded. Non-destructive evaluation of a wider range of thinning treatments available in these trials was undertaken with Pilodyn and Fakopp tools. Disc samples were also taken for basic density and modulus of elasticity. Differences between treatments for all wood property assessments were generally small and not significantly different.Thinning and pruning had little effect on the stem diameter growth required to achieve occlusion, therefore occlusion would be more rapid after thinning due to more rapid stem diameter growth. The difference between the treatments of greatest management interest, thinned and pruned (T&P) and unthinned and unpruned (UT&UP) were small. The production of higher value clear wood produced after all knots had occluded, measured as the average stem diameter growth over occlusion of the three outermost knots, was approximately 2 centimetres diameter. Two of the treatments can be ruled out as viable management alternatives: (i) the effect of thinning without pruning (T&UP) is clear, leading to a large inner core of stem wood containing knots (large knotty core diameter) and (ii) pruning without thinning (UT&P) results in a small knotty core diameter, however the tree and therefore log diameters are also small.

The effect of initial spacing and thinning on wood quality and graded sawn recovery of mature Caribbean pine grown in Queensland.

A mature Caribbean pine (Pinus caribaea var. hondurensis) silviculture experiment provided initial square spacing treatments of 1.8 m2, 2.4 m2, 3.0 m2 and 3.6 m2 (equal to 3088, 1737, 1111 and 772 stems/ha) that were thinned at age 10 years to 600, 400 and 200 stems/ha, retaining an unthinned control for each initial spacing. The trial was destructively sampled at age of 28 years and discs taken along 8 various stem heights were analysed for variation in basic density and SilviScan wood properties. In addition, the logs from ten stocking × thinning treatments were processed in a sawing study. Results indicate thinning effects were generally more pronounced than initial spacing effects. Fast growing trees produced wood with significantly higher average wood densities and higher average stiffness values. Detailed SilviScan densitometry results obtained radially and at various stem heights enabled construction of tree maps for wood properties, providing insights into the variation in juvenile to mature wood proportion across the initial and post-thinning stocking treatments studied. Dried dressed recovery was strongly related to tree size, and log value decreased consistently from butt to top logs across all treatments. The estimated value per hectare was highest in unthinned plots due to values being multiplied by high stem numbers per hectare. However, a complete economic analysis considering all cost structures is required to investigate the optimal silviculture to maximise economic returns to growers and processors. Improved understanding of the relationship between initial spacing, post-thinning stocking and wood and end-product quality should help to customize future forest management strategies required to produce better quality wood and wood products.

Selecting hardwood taxa for wood and fibre production in Queensland's subtropics.

Optimal matching of species to sites is required for a sustainable hardwood plantation industry in the subtropics. This paper reports the performance and adaptation of 60 taxa (species, provenances and hybrids) across two rainfall zones and a range of soil types in southern Queensland. Specifically, performance of taxa is compared across five replicated taxon–site matching trials at age 6 y. Three trials are in a 1000-mm y–1 rainfall zone of the Wide Bay region near Miriam Vale and two in a drier (about 750 mm y–1) rainfall zone near Kingaroy in the South Burnett region. In the higher-rainfall zone, the taxa with the fastest growth in the three trials at age 6 y were Corymbia citriodora subsp. variegata Woondum provenance, which ranked 1st, 6th and 5th respectively; E. longirostrata Coominglah provenance, ranked 3rd, 2nd and 3rd; and two sources of E. grandis, Copperlode provenance (ranked 4th and 1st) and SAPPI seed orchard (ranked 6th and 4th), which were planted in only two of the three trials. Similarly, in the lower-rainfall zone, E. grandis and its hybrids appear promising from the 6-y growth data., This excellent early growth, however, has not continued in either rainfall zone, with these taxa, 8 y after planting, now showing signs of stress and mortality. Based on trial results in these two rainfall zones, the taxon that appears the most promising for sustainable plantation development with high average annual volume index values and low incidence of borer attack is Corymbia citriodora subsp. variegata (6.7 m³ ha–1). Eucalyptus grandis and E. longirostrata both have better average annual volume indexes (8.2 m³ ha–1 and 7.4 m³ ha–1 respectively) but are very susceptible to borer attack. The current and long-term productivity and sustainability of plantation forestry in these rainfall zones is discussed. Further, the implications of predicted climate change (particularly reduced rainfall) for growing trees for fibre production and carbon sequestration are explored.