Growth and compaction behaviour of copper concentrate granules in a rotating drum

In order to understand the growth and compaction behaviour of chalcopyrite (copper concentrate), batch granulation tests were carried out using a rotating drum. The granule growth exhibited induction-type behaviour, as defined by Iveson and Litster [AIChE J. 44 (1998) 15 10]. There were two consecutive stages during granulation: the induction stage, during which the granules are gradually being compacted and little or no growth occurs, and the rapid growth stage, which starts when the granules have become surface wet and are rapidly growing. In agreement with earlier findings. an increased amount of binder liquid shortened the induction time. The compaction behaviour was also investigated. A displaced volume method was adopted to determine the porosity of the granules. It was shown that this technique had a limitation as it was unable to detect the reduction of the volumes of the granule pores after the granules had become surface wet. Due to this, some of the measurements were not suited for fitting a three-parameter empirical model. Attempts were made to determine whether the rapid growth stage started with the pore saturation exceeding a certain critical value, but due to the scatter in the porosity measurements and the fact that some of the measurements could not be used, it was not possible to determine a critical pore saturation, However, the porosity measurements clearly demonstrated that the porosity of the granules decreased during the induction stage of an experiment and that when rapid growth occurred, the granules had a pore saturation was around 0.85. This value was slightly lower than unity, which is most likely due to trapped air bubbles. (C) 2002 Published by Elsevier Science B.V.

Influence of environmental temperature and humidity on the acute ventilatory response to exercise in asthmatic adolescents

Asthma is a chronic inflammatory disorder of the respiratory airways affecting people of all ages, and constitutes a serious public health problem worldwide (6). Such a chronic inflammation is invariably associated with injury and repair of the bronchial epithelium known as remodelling (11). Inflammation, remodelling, and altered neural control of the airways are responsible for both recurrent exacerbations of asthma and increasingly permanent airflow obstruction (11, 29, 34). Excessive airway narrowing is caused by altered smooth muscle behaviour, in close interaction with swelling of the airway walls, parenchyma retractile forces, and enhanced intraluminal secretions (29, 38). All these functional and structural changes are associated with the characteristic symptoms of asthma – cough, chest tightness, and wheezing –and have a significant impact on patients’ daily lives, on their families and also on society (1, 24, 29). Recent epidemiological studies show an increase in the prevalence of asthma, mainly in industrial countries (12, 25, 37). The reasons for this increase may depend on host factors (e.g., genetic disposition) or on environmental factors like air pollution or contact with allergens (6, 22, 29). Physical exercise is probably the most common trigger for brief episodes of symptoms, and is assumed to induce airflow limitations in most asthmatic children and young adults (16, 24, 29, 33). Exercise-induced asthma (EIA) is defined as an intermittent narrowing of the airways, generally associated with respiratory symptoms (chest tightness, cough, wheezing and dyspnoea), occurring after 3 to 10 minutes of vigorous exercise with a maximal severity during 5 to 15 minutes after the end of the exercise (9, 14, 16, 24, 33). The definitive diagnosis of EIA is confirmed by the measurement of pre- and post-exercise expiratory flows documenting either a 15% fall in the forced expiratory volume in 1 second (FEV1), or a ≥15 to 20% fall in peak expiratory flow (PEF) (9, 24, 29). Some types of physical exercise have been associated with the occurrence of bronchial symptoms and asthma (5, 15, 17). For instance, demanding activities such as basketball or soccer could cause more severe attacks than less vigorous ones such as baseball or jogging (33). The mechanisms of exercise-induced airflow limitations seem to be related to changes in the respiratory mucosa induced by hyperventilation (9, 29). The heat loss from the airways during exercise, and possibly its post-exercise rewarming may contribute to the exercise-induced bronchoconstriction (EIB) (27). Additionally, the concomitant dehydration from the respiratory mucosa during exercise leads to an increased interstitial osmolarity, which may also contribute to bronchoconstriction (4, 36). So, the risk of EIB in asthmatically predisposed subjects seems to be higher with greater ventilation rates and the cooler and drier the inspired air is (23). The incidence of EIA in physically demanding coldweather sports like competitive figure skating and ice hockey has been found to occur in up to 30 to 35% of the participants (32). In contrast, swimming is often recommended to asthmatic individuals, because it improves the functionality of respiratory muscles and, moreover, it seems to have a concomitant beneficial effect on the prevalence of asthma exacerbations (14, 26), supporting the idea that the risk of EIB would be smaller in warm and humid environments. This topic, however, remains controversial since the chlorified water of swimming pools has been suspected as a potential trigger factor for some asthmatic patients (7, 8, 20, 21). In fact, the higher asthma incidence observed in industrialised countries has recently been linked to the exposition to chloride (7, 8, 30). Although clinical and epidemiological data suggest an influence of humidity and temperature of the inspired air on the bronchial response of asthmatic subjects during exercise, some of those studies did not accurately control the intensity of the exercise (2, 13), raising speculation of whether the experienced exercise overload was comparable for all subjects. Additionally, most of the studies did not include a control group (2, 10, 19, 39), which may lead to doubts about whether asthma per se has conditioned the observed results. Moreover, since the main targeted age group of these studies has been adults (10, 19, 39), any extrapolation to childhood/adolescence might be questionable regarding the different lung maturation. Considering the higher incidence of asthma in youngsters (30) and the fact that only the works of Amirav and coworkers (2, 3) have focused on this age group, a scarcity of scientific data can be identified. Additionally, since the main environmental trigger factors, i.e., temperature and humidity, were tested separately (10, 28, 39) it would be useful to analyse these two variables simultaneously because of their synergic effect on water and heat loss by the airways (31, 33). It also appears important to estimate the airway responsiveness to exercise within moderate environmental ranges of temperature and humidity, trying to avoid extreme temperatures and humidity conditions used by others (2, 3). So, the aim of this study was to analyse the influence of moderate changes in air temperature and humidity simultaneously on the acute ventilatory response to exercise in asthmatic children. To overcome the above referred to methodological limitations, we used a 15 minute progressive exercise trial on a cycle ergometer at 3 different workload intensities, and we collected data related to heart rate, respiratory quotient, minute ventilation and oxygen uptake in order to ensure that physiological exercise repercussions were the same in both environments. The tests were done in a “normal” climatic environment (in a gymnasium) and in a hot and humid environment (swimming pool); for the latter, direct chloride exposition was avoided.

The periodic table: contest and exhibition

The systemization and organization of ideas and concepts is an integral part of science. In chemistry, the organization of the periodic table of the chemical elements in the 1860s was one of the greatest scientific breakthroughs ever made and in fact during the 20th century it became a universally recognized scientific icon (1). The periodic table is the fundamental classificatory scheme of the elements and summarizes the realm of chemistry (2). Simply knowing the position of an element in the periodic table tells us about its properties and is usually enough to predict how the element will behave in a wide variety of different situations or reactions (1). Based on this potential mine of information, it is possible to make reliable predictions of the properties of the compounds that each element forms. Nowadays, the concept of the periodic table is starting to interact with other sciences and reports of periodic tables of amino acids (3), genetic codes (4), protein structures (5), and biology (6) can be found in the specialized literature. Symbiosis between science and art, for example, “The Periodic Table of The Elephants” (7), can also be seen. To appeal to a better understanding of the periodic table, the Instituto Superior de Engenharia do Instituto Politécnico do Porto and the Centro de Química da Universidade do Porto promoted a contest and exhibit with the goal of stimulating a wide and heterogeneous audience, ranging from young children and their parents to graduate students from several disciplines, to explore the nature of this icon. Imaginative educational activities such as contests (8–10), games (11, 12), and puzzles (13–15) provided a way to communicate with the general public with the goal of attracting students to science. This also constituted an interesting, informative, and entertaining alternative to non-interactive lectures. Simultaneously, artistic creativity was combined with scientific knowledge.

Occupational stress and coping resources in physiotherapists: a survey of physiotherapists in three general hospitals

Objectives - To identify occupational stressors and coping resources in a group of physiotherapists, and to analyse interactions between subjective levels of stress, efficacy in stress resolution and coping resources used by these professionals. Design - A sample of 55 physiotherapists working in three general hospitals in Portugal completed the Coping Resources Inventory for Stress, the Occupational Stressors Inventory and two subjective scales for stress and stress resolution. Main results - Most physiotherapists perceived that they were moderately stressed (19/55, 35%) or stressed (20/55, 36%) due to work, and reported that their efficacy in stress resolution was moderate (25/54, 46%) or efficient (23/54, 42%). Issues related to lack of professional autonomy, lack of organisation in the hierarchical command chain, lack of professional and social recognition, disorganisation in task distribution and interpersonal conflicts with superiors were identified as the main sources of stress. The most frequently used coping resources were social support, stress monitoring, physical health and structuring. Perceived efficacy in stress resolution was inversely related to perceived level of occupational stress (r = −0.61, P < 0.01). Significant correlations were found between several coping resources and the perceived level of stress and efficacy in stress resolution. Associations between problem solving, cognitive restructuring and stress monitoring and both low levels of perceived stress and high levels of perceived efficacy were particularly strong. Implications for practice - The importance of identifying stressors and coping resources related to physiotherapists’ occupational stress, and the need for the development of specific training programmes to cope with stress are supported.

Soil sampling design and sampling techniques for soil properties monitoring – common difficulties related to forest soils

Mathematical models and statistical analysis are key instruments in soil science scientific research as they can describe and/or predict the current state of a soil system. These tools allow us to explore the behavior of soil related processes and properties as well as to generate new hypotheses for future experimentation. A good model and analysis of soil properties variations, that permit us to extract suitable conclusions and estimating spatially correlated variables at unsampled locations, is clearly dependent on the amount and quality of data and of the robustness techniques and estimators. On the other hand, the quality of data is obviously dependent from a competent data collection procedure and from a capable laboratory analytical work. Following the standard soil sampling protocols available, soil samples should be collected according to key points such as a convenient spatial scale, landscape homogeneity (or non-homogeneity), land color, soil texture, land slope, land solar exposition. Obtaining good quality data from forest soils is predictably expensive as it is labor intensive and demands many manpower and equipment both in field work and in laboratory analysis. Also, the sampling collection scheme that should be used on a data collection procedure in forest field is not simple to design as the sampling strategies chosen are strongly dependent on soil taxonomy. In fact, a sampling grid will not be able to be followed if rocks at the predicted collecting depth are found, or no soil at all is found, or large trees bar the soil collection. Considering this, a proficient design of a soil data sampling campaign in forest field is not always a simple process and sometimes represents a truly huge challenge. In this work, we present some difficulties that have occurred during two experiments on forest soil that were conducted in order to study the spatial variation of some soil physical-chemical properties. Two different sampling protocols were considered for monitoring two types of forest soils located in NW Portugal: umbric regosol and lithosol. Two different equipments for sampling collection were also used: a manual auger and a shovel. Both scenarios were analyzed and the results achieved have allowed us to consider that monitoring forest soil in order to do some mathematical and statistical investigations needs a sampling procedure to data collection compatible to established protocols but a pre-defined grid assumption often fail when the variability of the soil property is not uniform in space. In this case, sampling grid should be conveniently adapted from one part of the landscape to another and this fact should be taken into consideration of a mathematical procedure.

Functional and structural studies of two enzymes: membrane bound kinase and Z-DNA/Z-RNA-binding protein

Dissertação para obtenção do Grau de Doutor em Sistemas de Bioengenharia

Engineering bio-based polymers using alternative solvents and processes

The work presented in this thesis explores novel routes for the processing of bio-based polymers, developing a sustainable approach based on the use of alternative solvents such as supercritical carbon dioxide (scCO2), ionic liquids (ILs) and deep eutectic solvents (DES). The feasibility to produce polymeric foams via supercritical fluid (SCF) foaming, combined with these solvents was assessed, in order to replace conventional foaming techniques that use toxic and harmful solvents. A polymer processing methodology is presented, based on SCF foaming and using scCO2 as a foaming agent. The SCF foaming of different starch based polymeric blends was performed, namely starch/poly(lactic acid) (SPLA) and starch/poly(ε-caprolactone) (SPCL). The foaming process is based on the fact that CO2 molecules can dissolve in the polymer, changing their mechanical properties and after suitable depressurization, are able to create a foamed (porous) material. In these polymer blends, CO2 presents limited solubility and in order to enhance the foaming effect, two different imidazolium based ILs (IBILs) were combined with this process, by doping the blends with IL. The use of ILs proved useful and improved the foaming effect in these starch-based polymer blends. Infrared spectroscopy (FTIR-ATR) proved the existence of interactions between the polymer blend SPLA and ILs, which in turn diminish the forces that hold the polymeric structure. This is directly related with the ability of ILs to dissolve more CO2. This is also clear from the sorption experiments results, where the obtained apparent sorption coefficients in presence of IL are higher compared to the ones of the blend SPLA without IL. The doping of SPCL with ILs was also performed. The foaming of the blend was achieved and resulted in porous materials with conductivity values close to the ones of pure ILs. This can open doors to applications as self-supported conductive materials. A different type of solvents were also used in the previously presented processing method. If different applications of the bio-based polymers are envisaged, replacing ILs must be considered, especially due to the poor sustainability of some ILs and the fact that there is not a well-established toxicity profile. In this work natural DES – NADES – were the solvents of choice. They present some advantages relatively to ILs since they are easy to produce, cheaper, biodegradable and often biocompatible, mainly due to the fact that they are composed of primary metabolites such as sugars, carboxylic acids and amino-acids. NADES were prepared and their physicochemical properties were assessed, namely the thermal behavior, conductivity, density, viscosity and polarity. With this study, it became clear that these properties can vary with the composition of NADES, as well as with their initial water content. The use of NADES in the SCF foaming of SPCL, acting as foaming agent, was also performed and proved successful. The SPCL structure obtained after SCF foaming presented enhanced characteristics (such as porosity) when compared with the ones obtained using ILs as foaming enhancers. DES constituted by therapeutic compounds (THEDES) were also prepared. The combination of choline chloride-mandelic acid, and menthol-ibuprofen, resulted in THEDES with thermal behavior very distinct from the one of their components. The foaming of SPCL with THEDES was successful, and the impregnation of THEDES in SPCL matrices via SCF foaming was successful, and a controlled release system was obtained in the case of menthol-ibuprofen THEDES.

Acanthotylotra alvarengai (Porifera, Demospongiae) new genus and species of sponge from Tocantins river, Pará State, Brazil

Acanthotylotra a new monotypic genus of freshwater sponge is defined. Its sole species A. alvarengai sp. nov. is described based upon microscopic specimens recovered from the Tocantins river, Pará State, Brazil, when the deep rocky substrate was temporarily exposed downstream from the dam at the time it was closed for lake formation. A unique set of megascleres, allied to the paucity of spongin, the renieroid skeleton and the fact that gemmules or new specimens remain undetected, call for the proposition of a new monospecific genus to be retained as incertae sedis until new larger and probably gemmuliferous specimens come to be found.

Ten Propositions on Rural Poverty and Agrarian Transition in Central Eurasia

The relation between agricultural development and rural poverty reduction in six Central Eurasian countries, namely Azerbaijan (South Caucasus) and Kazakhstan, Kyrgyzstan, Tajikistan, Turkmenistan and Uzbekistan (Central Asia), is discussed by presenting and analyzing ten propositions. These propositions cover a broad range of issues that relate to rural poverty in this region, such as: the state of income and non-income poverty; the diverse processes of land reform and farm restructuring, and agricultural policy reform; and finally, the institutional and market framework that is needed for dynamic agricultural and rural development. The paper contends that rural poverty is not responding as robustly to rapid economic growth in these countries, and that agricultural growth, in particular in the newly emerging peasant farm sector, is necessary to promote rural poverty reduction.

Iterative reconstruction methods in two different MDCT scanners: Physical metrics and 4-alternative forced-choice detectability experiments - A phantom approach.

This paper characterizes and evaluates the potential of three commercial CT iterative reconstruction methods (ASIR?, VEO? and iDose(4 ()?())) for dose reduction and image quality improvement. We measured CT number accuracy, standard deviation (SD), noise power spectrum (NPS) and modulation transfer function (MTF) metrics on Catphan phantom images while five human observers performed four-alternative forced-choice (4AFC) experiments to assess the detectability of low- and high-contrast objects embedded in two pediatric phantoms. Results show that 40% and 100% ASIR as well as iDose(4) levels 3 and 6 do not affect CT number and strongly decrease image noise with relative SD constant in a large range of dose. However, while ASIR produces a shift of the NPS curve apex, less change is observed with iDose(4) with respect to FBP methods. With second-generation iterative reconstruction VEO, physical metrics are even further improved: SD decreased to 70.4% at 0.5 mGy and spatial resolution improved to 37% (MTF(50%)). 4AFC experiments show that few improvements in detection task performance are obtained with ASIR and iDose(4), whereas VEO makes excellent detections possible even at an ultra-low-dose (0.3 mGy), leading to a potential dose reduction of a factor 3 to 7 (67%-86%). In spite of its longer reconstruction time and the fact that clinical studies are still required to complete these results, VEO clearly confirms the tremendous potential of iterative reconstructions for dose reduction in CT and appears to be an important tool for patient follow-up, especially for pediatric patients where cumulative lifetime dose still remains high.

Magma generation at the easternmost section of the Hellenic arc: Hf, Nd, Pb and Sr isotope geochemistry of Nisyros and Yali volcanoes (Greece)

Geochemical and petrographical studies of lavas and ignimbrites from the Quaternary Nisyros-Yali volcanic system in the easternmost part of the Hellenic arc (Greece) reveal insight into magma generating processes. A compositional gap between 61 and 68 wt.% SiO2 is recognized that coincides with the stratigraphic distinction between pre-caldera and postcaldera volcanic units. Trace element systematics support the subdivision of Nisyros and Yali volcanic units into two distinct suites of rocks. The variation of Nd and Hf present day isotope data and the fact that they are distinct from the isotope compositions of MORB rule out an origin by pure differentiation and require assimilation of a crustal component. Lead isotope ratios of Nisyros and Yali volcanic rocks support mixing of mantle material with a lower crust equivalent. However, Sr-87/Sr-86 ratios of 0.7036-0.7048 are incompatible with a simple binary mixing scenario and give low depleted mantle extraction ages (< 0.1 Ga), in contrast with Pb model ages of 0.3 Ga and Hf and Nd model ages of ca. 0.8 Ga. The budget of fluid-mobile elements Sr and Pb is likely to be dominated by abundant hydrous fluids characterised by mantle-like Sr isotope ratios. Late stage fluids probably were enriched in CO2, needed to explain the high Th concentrations. The occurrence of hydrated minerals (e.g., amphibole) in the first post-caldera unit with the lowermost Sr-87/Sr-86 ratio of 0.7036 +/- 2 can be interpreted as the result of the increased water activity in the source. The presence of two different plagioclase phenocryst generations in the first lava subsequent to the caldera-causing event is indicative for a longer storage time of this magma at a shallower level. A model capable of explaining these observations involves three evolutionary stages. First stage, assimilation of lower crustal material by a primitive magma of mantle origin (as modelled by Nd-Hf isotope systematics). This stage ended by an interruption in replenishment that led to an increase of crystallization and, hence, an increase in viscosity, suppressing eruption. During this time gap, differentiation by fractional crystallization led to enrichment of incompatible species, especially aqueous fluids, to silica depolymerisation and to a decrease in viscosity, finally enabling eruption again in the third stage. (c) 2005 Elsevier B.V. All rights reserved.

Different profiles of immune reconstitution in children and adults with HIV-infection after highly active antiretroviral therapy.

BACKGROUND Recent advances in characterizing the immune recovery of HIV-1-infected people have highlighted the importance of the thymus for peripheral T-cell diversity and function. The aim of this study was to investigate differences in immune reconstitution profiles after highly active antiretroviral therapy (HAART) between HIV-children and adults. METHODS HIV patients were grouped according to their previous clinical and immunological status: 9 HIV-Reconstituting-adults (HIV-Rec-adults) and 10 HIV-Reconstituting-children (HIV-Rec-children) on HAART with viral load (VL) and CD4+ >or=500 cells/microL at least during 6 months before the study and CD4+ and 20 healthy-children (control subjects) were used to calculate Z-score values to unify value scales between children and adults to make them comparable. RESULTS HIV-Rec-children had higher T-cell receptor excision circles (TREC) and lower interleukin (IL)-7 levels than HIV-Rec-adults (p < 0.05). When we analyzed Z-score values, HIV-Rec-children had higher TREC Z-score levels (p = 0.03) than HIV-Rec-adults but similar IL-7 Z-score levels. Regarding T-cell subsets, HIV-Rec-children had higher naïve CD4+ (CD4+CD45RA hi+CD27+), naïve CD8+ (CD8+CD45RA hi+CD27+), and memory CD8+ (CD8+CD45RO+) cells/microl than HIV-Rec-adults, but similar memory CD4+ (CD4+CD45RO+) counts. HIV-Rec-children had lower naïve CD8+ Z-score values than HIV-Rec-adults (p = 0.05). CONCLUSION Our data suggest that HIV-Rec-children had better thymic function than HIV-Rec-adults and this fact affects the peripheral T-cell subsets. Thus, T-cell recovery after HAART in HIV-Rec-adults could be the consequence of antigen-independent peripheral T-cell expansion while in HIV-Rec-children thymic output could play a predominant role in immune reconstitution.

A nuclear ribosomal DNA pseudogene in triatomines opens a new research field of fundamental and applied implications in Chagas disease

A pseudogene, designated as "ps(5.8S+ITS-2)", paralogous to the 5.8S gene and internal transcribed spacer (ITS)-2 of the nuclear ribosomal DNA (rDNA), has been recently found in many triatomine species distributed throughout North America, Central America and northern South America. Among characteristics used as criteria for pseudogene verification, secondary structures and free energy are highlighted, showing a lower fit between minimum free energy, partition function and centroid structures, although in given cases the fit only appeared to be slightly lower. The unique characteristics of "ps(5.8S+ITS-2)" as a processed or retrotransposed pseudogenic unit of the ghost type are reviewed, with emphasis on its potential functionality compared to the functionality of genes and spacers of the normal rDNA operon. Besides the technical problem of the risk for erroneous sequence results, the usefulness of "ps(5.8S+ITS-2)" for specimen classification, phylogenetic analyses and systematic/taxonomic studies should be highlighted, based on consistence and retention index values, which in pseudogenic sequence trees were higher than in functional sequence trees. Additionally, intraindividual, interpopulational and interspecific differences in pseudogene amount and the fact that it is a pseudogene in the nuclear rDNA suggests a potential relationships with fitness, behaviour and adaptability of triatomine vectors and consequently its potential utility in Chagas disease epidemiology and control.

From print to screen: changes and challenges facing the Brazilian publishing industry

The publishing industry is at a turning point. Facing the first major disruptive innovation in five centuries, its long-established structure and business model are at stake. Building on literature based on the pitfalls for incumbents, we interviewed key executives from the major publishers in Brazil to understand their perspective. We find that not only are they facing those pitfalls, but we also propose a new one, The Industry View Trap, concerning challenges created by convergence, the difficulty to deal with changes in the ecosystem and the fact that the very definition of the industry you're part of might have changed.

Portraying innovation in the public service of Brazil: Frameworks, systematization and characterization

ABSTRACT Innovation is essential for improving organizational performance in both the private and public sectors. This article describes and analyzes the 323 innovation experiences of the Brazilian federal public service that received prizes during the 16 annual competitions (from 1995 to 2012) of the Award for Innovation in Federal Public Management held by the Brazilian National School of Public Administration (ENAP). It is a qualitative and quantitative study in which were employed as categories for analysis the four types of innovation defined in the Copenhagen Manual: product, process, organizational and communication. The survey results allow us to affirm that there is innovation in the public sector, in spite of the skepticism of some researchers and the incipient state of theoretical research on the subject. It was possible to observe that organizational innovation was the one with the highest number of award- -winning experience, followed respectively by process, communication and product innovation, with citizen services and improvement of work processes being the main highlights. The results showed that, although the high incidence of innovation occurs at the national level, a significant number of innovations also occur at the local level, probably because many organizations of the federal government have their actions spread only at this level of government. Concerning the innovative area, health and education predominate, with almost 33% of initiatives, which can be explained by capillarity of these areas and the fact that both maintain a strong interaction with the user. The contributions of this work include the use of theoretical model of innovation analysis in the public sector in Brazil still upcoming, and the systematization of knowledge in empirical basis for this innovation. In this sense, it also contributes to the development of the theory with the presentation of evidence that the characteristics, determinants and consequences of innovation in the public sector differ not only from innovation in the industry, but also from innovation in services in the private sector.