Microstructural evolution during hot deformation of duplex stainless steel

The microstructure evolution during hot deformation of a 23Cr-5Ni-3Mo duplex stainless steel was investigated in torsion. The presence of a soft δ ferrite phase in the vicinity of austenite caused strain partitioning, with accommodation of more strain in the δ ferrite. Furthermore, owing to the limited number of austenite/austenite grain boundaries, the kinetics of dynamic recrystallisation (DRX) in austenite was very slow. The first DRX grains in the austenite phase formed at a strain beyond the peak and proceeded to <15% of the microstructure at the rupture strain of the sample. On the other hand, the microstructure evolution in δ ferrite started by formation of low angle grain boundaries at low strains and the density of these boundaries increased with increasing strain. There was clear evidence of continuous dynamic recrystallisation in this phase at strains beyond the peak. However, in the δ ferrite phase at high strains, most grains consisted of δ/δ and δ/γ boundaries.

Dynamic adjustment of ferrite grains during dynamic strain induced transformation

The dynamic adjustment of ferrite grains formed during 'dynamic strain induced transformation (DSIT)' is an important feature of this mechanism that has not been addressed previously. A novel experimental method was applied to follow the effect of deformation at different stages on ferrite formed initially through DSIT. It is shown that while the continuous dynamic recrystallisation (CDRX) appears to be an acceptable mechanism for re-refinement of coarser grain size (i.e. dα>2dDSIT), it cannot explain the steady state grain size for finer ferrite grains (i.e. dα<2dDSIT). Other potential mechanisms involved in this phenomenon are examined.

Effect of solidification grain refinement on the development of wrought Mg alloys

A recent trial investigated the effect of solidification grain refinement of billet on the grain refinement and properties of alloy ZM20. It was found that even at levels of 0.4Mn, significant grain refinement could be obtained when 0.7Zr was added. At 0.2Mn grain sizes as low as 60μm were
obtained. Billets of Mg-2Zn-0.2Mn with four different grain sizes, due to different Zr and cooling rates were then cast via vertical direct chill casting and extruded conventionally. Benefits of grain refinement of the billet on extrusion were found to be a slight increase in the size of the operating
window, and a reduction of the grain size in the extrudate. However, the effect of the reduction in extrudate grain size due to refinement of the billet was small compared with the amount of grain refinement obtained due to recrystallisation on extrusion.

Integrated model for thermo-mechanical controlled process in rod (or bar) rolling

This study presents an integrated model for computing the thermo-mechanical parameters (cross-sectional shape of workpiece, the pass-by-pass strain and strain rate and the temperature variation during rolling and cooling between inter-stands) and metallurgical parameters (recrystallisation behaviour and austenite grain size—AGS), to assess the potential for developing “Thermo-Mechanical Controlled Process” technology in rod (or bar) rolling, which has been a well-known technical terminology in strip (or plate) rolling since 1970s.

The advantage of this model is that metallurgical and mechanical parameters are obtained simultaneously in a short computation time compared with other models. The model has been applied to a rod mill to predict the exit cross-sectional shape, area and AGS per pass by incorporating the equations for AGS evolution being used in strip rolling. At the finishing train of rod mills, the strain rates reach as high as 1000–3000 s−1 and the inter-pass times are around 10–60 ms.

The results show that the proposed model is an efficient tool for evaluating the effects of process-related parameters on product quality and dimensional tolerance of the products in rod (or bar) rolling. The results of the simulation demonstrated that the equation for AGS evolution being used in strip rolling might have limitations when applied directly to rod rolling at a high strain rate.

Construction of extrusion limit diagram for AZ31 magnesium alloy by FE simulation

The maximum speed at which magnesium can be extruded is considerably slower than that of many common aluminium extrusion alloys. This affects both the economies of production and the final mechanical behaviour. The present work quantifies the limiting extrusion speeds and ratios of magnesium alloy AZ31 as a function of billet temperature. This is done by combining hot compression test results, FE simulations and extrusion trials. Hot working stress–strain curves displayed a distinct dynamic recrystallisation peak. These data were used as a “look-up” table for the FE simulations in which the cracking limit was assumed to occur when the surface temperature reaches the incipient melting point. The maximum extrusion ratio predicted using FE analysis dropped from 90 to 40 when the extrusion ram speed was raised from 5 to 50 mm/s. The predicted limits agree well with the occurrence of cracking in both a laboratory and a commercial extrusion trial.

Conversion of the hot torsion test results into flow curve with multiple regimes of hardening

The method of Fields and Backofen has been commonly used to reduce the data obtained by hot torsion test into flow curves. The method, however, is most suitable for materials with monotonic strain hardening behaviour. Other methods such as Stüwe’s method, tubular specimens, differential testing and the inverse method, each suffer from similar drawbacks. It is shown in the current work that for materials with multiple regimes of hardening any method based on an assumption of constant hardening indices introduces some errors into the flow curve obtained from the hot torsion test. Therefore such methods do not enable accurate prediction of onset of recrystallisation where slow softening occurs. A new method to convert results from the hot torsion test into flow curves by taking into account the variation of constitutive parameters during deformation is presented. The method represents the torque twist data by a parametric linear least square model in which Euler and hyperbolic coefficients are used as the parameters. A closed form relationship obtained from the mathematical representation of the data is employed next for flow stress determination. Two different solution strategies, the method of normal equations and singular value decomposition, were used for parametric modelling of the data with hyperbolic basis functions. The performance of both methods is compared. Experimental data obtained by FHTTM, a flexible hot torsion test machine developed at IROST, for a C–Mn austenitic steel was used to demonstrate the method. The results were compared with those obtained using constant strain and strain rate hardening characteristics.

Characterization on ferrite microstructure evolution during large strain warm torsion testing of plain low carbon steel

Ferrite grain/subgrain structures evolution during the extended dynamic softening of a plain low carbon steel was investigated throughout the large strain warm deformation by hot torsion. Microstructural analysis with electron back-scattering diffraction (EBSD) scanning electron microscope (FEG/SEM) was carried out on the ferrite microstructural parameters. The results showed that the warm flow stress–strain curves are similar to those affected only by dynamic softening and an extended warm flow softening is seen during large strain deformation up to 30. Furthermore, with an increase in strain up to ~ vert, similar1 the grain size of ferrite, misorientation angle and fraction of high-angle boundaries gradually decrease and fraction of low-angle boundaries increases. With a further increase in the strain beyond ~, vert, similar2, these parameters remain approximately unchanged. No evidence of discontinuous dynamic recrystallisation involving nucleation and growth of new grains was found within ferrite. Therefore, the dynamic softening mechanism observed during large strain ferritic deformation is explained by continuous dynamic recrystallization (CDRX).

Grain refinement through controlled thermomechanical processing

The major challenge for thermomechanical processing is to extend grain refinement towards lower average grain sizes. However, there is also a need to provide a better understanding of the mechanisms through which the refinement processes proceed. Many recent proposals for advanced thermomechanical processing rely on the dynamic strain induced transformation (DSIT), and the dynamic recrystallisation of austenite as the main refinement mechanisms. These mechanisms are still not fully understood and their clarification can be expected to lead to even greater levels of refinement. The current review examines the roles of ferrite recrystallisation , DSIT and initial austenite grain size. It is shown that although the ferrite recrystallisation mechanism in DSIT has certain similarities with the well known continuous dynamic recrystallisation (CDRX), it is significantly affected by the transformed ferrite grain size. Also, reducing the initial austenite grain size increases the recrystallisation rate in the strain dependent as well as strain independent regions. These results show that the traditional concept of metadynamic recrystallisation is insufficient to explain the changes in grain size following deformation. An alternative explanation is presented.

Softening mechanisms in two duplex stainless steels deformed in hot torsion

The aim of the present work was to undertake a detailed investigation of the softening mechanisms during hot deformation of a 21Cr-10Ni-3Mo (steel A) and a 21Cr-8Ni-3Mo (steel B) austenite/ferrite duplex stainless steels containing about 60% and 30% of austenite, respectively. The steels were subjected to hot deformation in torsion performed at 900 ºC and 1200 ºC using a strain rate of 0.7 s-1 to several strain levels. Quantitative optical and transmission electron microscopy were used in the investigation. Austenite was observed to soften via dynamic recovery (DRV) and dynamic recrystallisation (DRX) accompanied by DRV for the deformation temperatures of 900 °C and 1200 °C, respectively, for the both steels studied. DRX of austenite largely occurred through strain-induced grain boundary migration, complemented by (multiple) twinning, and developed significantly faster in steel A than in steel B, indicating that considerably larger strains partitioned into austenite in the former steel during deformation at 1200 °C. The above softening mechanism was accompanied by the formation of DRX grains from subgrains along the austenite/ferrite interface and by large-scale subgrain coalescence. At 900°C, stressassisted phase transitions between austenite and ferrite were observed, characterised by dissolution of the primary austenite, formation of Widmanstätten secondary austenite and gradual globularisation of the microstructure with increasing strain. These processes appeared to be significantly more widespread in steel B. The softening mechanism within ferrite for the both steels studied was classified as “continuous DRX”, characterised by a gradual increase in misorientations between neighbouring subgrains with strain, for the both deformation temperatures.

Fine structure of shear bands formed during hot deformation of two austenitic steels

Shear bands formed during both cold and hot plastic deformation have been linked with several proposed mechanisms for the formation of ultrafine grains. The aim of the present work was to undertake a detailed investigation of the microstructural and crystallographic characteristics of the shear bands formed during hot deformation of a 22Cr-19Ni-3Mo (mass%) austenitic stainless steel and a Fe-30 mass%Ni based austenitic model alloy. These alloys were subjected to deformation in torsion and plane strain compression (PSC), respectively, at temperatures of 900°C and 950°C and strain rates of 0.7s_-1 and 10s_-1, respectively. Transmission electron microscopy and electron backscatter diffraction in conjunction with scanning electron microscopy were employed in the investigation. It has been observed that shear bands already started to form at moderate strains in a matrix of pre-existing microbands and were composed of fine, slightly elongated subgrains (fragments). These bands propagated along a similar macroscopic path and the subgrains, present within their substructure, were rotated relative to the surrounding matrix about axes approximately parallel to the sample radial and transverse directions for deformation in torsion and PSC, respectively. The subgrain boundaries were largely observed to be non-crystallographic, suggesting that the subgrains generally formed via multiple slip processes. Shear bands appeared to form through a co-operative nucleation of originally isolated subgrains that gradually interconnected with the others to form long, thin bands that subsequently thickened via the formation of new subgrains. The observed small dimensions of the subgrains present within shear bands and their large misorientations clearly indicate that these subgrains can serve as potent nucleation sites for the formation of ultrafine grain structures during both subsequent recrystallisation, as observed during the present PSC experiments, and phase transformation.

Evolution of hot working stress and microstructure of Mg-3Al-1Zn

The deformation behaviour of magnesium alloy AZ31 was examined. The work found that dynamic recrystallisation operates during hot deformation. The influence that different process variables have on this mechanism were quantified. The optimisation of dynamic recrystallisation allows magnesium alloys to be formed into products more easily whilst developing enhanced final properties.

21Cr - 10Ni - 3Mo duplex stainless steel high temperature deformation microstructures

Data includes EBSD orentation maps of the specimens deformed in torsion at 1200 degrees celsius to strains of 0.1, 0.5, 0.9 and 1.3. The phase ratio is about 60% austenite and 40% ferrite. The miscrostructure is dynamically recovered and there is also some dynamic recrystallisation at strains of 0.9 and 1.3. The main portion of softening can be attributed to dynamic subgrain coalescence in austenite.

Substructure and texture development in austenite through thermomechanical processing

The data collection was performed using EBSD and TEM techniques. The objective was to characterise the substructure and crystallographic texture development during dynamic and post-dynamic deformation. The work reveals the role of the initial dislocation structure and texture on the softening characteristics in austenite and how these evolve during softening. It is also shown that the differences in the deformation dislocation structures between the dynamically recrystallized and deformed regions play a major role in determining the extent of recovery. An enhanced static recovery can be seen during post dynamic softening.

Data gathered during investigations into the evolution of hot working stress and microstructure in Mg-3Al-1Zn

The data is the result of hot deformation tests conducted on magnesium alloy AZ31. It includes stress strain data for a range of deformation conditions and different initial microstructures. It also includes data for the developed grain size and the degree of dynamic recrystallisation.

Development of boundary misorientations during grain growth in silicon steels

Changes in grain size, texture and misorientation distributions have been monitored during extensive normal grain growth in 3%Si steels. The boundary misorientation distributions deviate significantly from the Mackenzie relationship. Comparisons of correlated and uncorrelated distributions show large excesses of low angle boundaries. However, these are not a result of low energy boundaries being favoured during grain growth since the deviation diminishes as growth proceeds. The effect originates in the nucleation of grains in colonies of similar orientation during primary recrystallisation. A slight tendency for promotion of 60º boundaries may indicate some preference for the retention of lower energy twin boundaries during grain growth in silicon steel.