A Multiwavelength Study of the Intracluster Medium and the Characterization of the Multiwavelength Sub/millimeter Inductance Camera

The first part of this thesis combines Bolocam observations of the thermal Sunyaev-Zel’dovich (SZ) effect at 140 GHz with X-ray observations from Chandra, strong lensing data from the Hubble Space Telescope (HST), and weak lensing data from HST and Subaru to constrain parametric models for the distribution of dark and baryonic matter in a sample of six massive, dynamically relaxed galaxy clusters. For five of the six clusters, the full multiwavelength dataset is well described by a relatively simple model that assumes spherical symmetry, hydrostatic equilibrium, and entirely thermal pressure support. The multiwavelength analysis yields considerably better constraints on the total mass and concentration compared to analysis of any one dataset individually. The subsample of five galaxy clusters is used to place an upper limit on the fraction of pressure support in the intracluster medium (ICM) due to nonthermal processes, such as turbulent and bulk flow of the gas. We constrain the nonthermal pressure fraction at r500c to be less than 0.11 at 95% confidence, where r500c refers to radius at which the average enclosed density is 500 times the critical density of the Universe. This is in tension with state-of-the-art hydrodynamical simulations, which predict a nonthermal pressure fraction of approximately 0.25 at r500c for the clusters in this sample.

The second part of this thesis focuses on the characterization of the Multiwavelength Sub/millimeter Inductance Camera (MUSIC), a photometric imaging camera that was commissioned at the Caltech Submillimeter Observatory (CSO) in 2012. MUSIC is designed to have a 14 arcminute, diffraction-limited field of view populated with 576 spatial pixels that are simultaneously sensitive to four bands at 150, 220, 290, and 350 GHz. It is well-suited for studies of dusty star forming galaxies, galaxy clusters via the SZ Effect, and galactic star formation. MUSIC employs a number of novel detector technologies: broadband phased-arrays of slot dipole antennas for beam formation, on-chip lumped element filters for band definition, and Microwave Kinetic Inductance Detectors (MKIDs) for transduction of incoming light to electric signal. MKIDs are superconducting micro-resonators coupled to a feedline. Incoming light breaks apart Cooper pairs in the superconductor, causing a change in the quality factor and frequency of the resonator. This is read out as amplitude and phase modulation of a microwave probe signal centered on the resonant frequency. By tuning each resonator to a slightly different frequency and sending out a superposition of probe signals, hundreds of detectors can be read out on a single feedline. This natural capability for large scale, frequency domain multiplexing combined with relatively simple fabrication makes MKIDs a promising low temperature detector for future kilopixel sub/millimeter instruments. There is also considerable interest in using MKIDs for optical through near-infrared spectrophotometry due to their fast microsecond response time and modest energy resolution. In order to optimize the MKID design to obtain suitable performance for any particular application, it is critical to have a well-understood physical model for the detectors and the sources of noise to which they are susceptible. MUSIC has collected many hours of on-sky data with over 1000 MKIDs. This work studies the performance of the detectors in the context of one such physical model. Chapter 2 describes the theoretical model for the responsivity and noise of MKIDs. Chapter 3 outlines the set of measurements used to calibrate this model for the MUSIC detectors. Chapter 4 presents the resulting estimates of the spectral response, optical efficiency, and on-sky loading. The measured detector response to Uranus is compared to the calibrated model prediction in order to determine how well the model describes the propagation of signal through the full instrument. Chapter 5 examines the noise present in the detector timestreams during recent science observations. Noise due to fluctuations in atmospheric emission dominate at long timescales (less than 0.5 Hz). Fluctuations in the amplitude and phase of the microwave probe signal due to the readout electronics contribute significant 1/f and drift-type noise at shorter timescales. The atmospheric noise is removed by creating a template for the fluctuations in atmospheric emission from weighted averages of the detector timestreams. The electronics noise is removed by using probe signals centered off-resonance to construct templates for the amplitude and phase fluctuations. The algorithms that perform the atmospheric and electronic noise removal are described. After removal, we find good agreement between the observed residual noise and our expectation for intrinsic detector noise over a significant fraction of the signal bandwidth.

The ionic basis of frequency selectivity in hair cells of the bullfrog's sacculus

Hair cells from the bull frog's sacculus, a vestibular organ responding to substrate-borne vibration, possess electrically resonant membrane properties which maximize the sensitivity of each cell to a particular frequency of mechanical input. The electrical resonance of these cells and its underlying ionic basis were studied by applying gigohm-seal recording techniques to solitary hair cells enzymatically dissociated from the sacculus. The contribution of electrical resonance to frequency selectivity was assessed from microelectrode recordings from hair cells in an excised preparation of the sacculus.

Electrical resonance in the hair cell is demonstrated by damped membrane-potential oscillations in response to extrinsic current pulses applied through the recording pipette. This response is analyzed as that of a damped harmonic oscillator. Oscillation frequency rises with membrane depolarization, from 80-160 Hz at resting potential to asymptotic values of 200-250 Hz. The sharpness of electrical tuning, denoted by the electrical quality factor, Q_e, is a bell-shaped function of membrane voltage, reaching a maximum value around eight at a membrane potential slightly positive to the resting potential.

In whole cells, three time-variant ionic currents are activated at voltages more positive than -60 to -50 mV; these are identified as a voltage-dependent, non-inactivating Ca current (I_ca), a voltage-dependent, transient K current (I_a), and a Ca-dependent K current (I_c). The C channel is identified in excised, inside-out membrane patches on the basis of its large conductance (130-200 pS), its selective permeability to Kover Na or Cl, and its activation by internal Ca ions and membrane depolarization. Analysis of open- and closed-lifetime distributions suggests that the C channel can assume at least two open and three closed kinetic states.

Exposing hair cells to external solutions that inhibit the Ca or C conductances degrades the electrical resonance properties measured under current-clamp conditions, while blocking the A conductance has no significant effect, providing evidence that only the Ca and C conductances participate in the resonance mechanism. To test the sufficiency of these two conductances to account for electrical resonance, a mathematical model is developed that describes I_ca, I_c, and intracellular Ca concentration during voltage-clamp steps. I_ca activation is approximated by a third-order Hodgkin-Huxley kinetic scheme. Ca entering the cell is assumed to be confined to a small submembrane compartment which contains an excess of Ca buffer; Ca leaves this space with first-order kinetics. The Ca- and voltage-dependent activation of C channels is described by a five-state kinetic scheme suggested by the results of single-channel observations. Parameter values in the model are adjusted to fit the waveforms of I_ca and I_c evoked by a series of voltage-clamp steps in a single cell. Having been thus constrained, the model correctly predicts the character of voltage oscillations produced by current-clamp steps, including the dependencies of oscillation frequency and Q_e on membrane voltage. The model shows quantitatively how the Ca and C conductances interact, via changes in intracellular Ca concentration, to produce electrical resonance in a vertebrate hair cell.

Nd3+螯合物的含氢有机溶液光谱性能研究

Tris-thenoyltrifluroacetonate of Nd3+ has been prepared and dissolved in DMF solation with very high concentration, and the contained hydrogen has not been substituted by deuterium. The absorption spectrum, emission spectrum, and fluorescence lifetime of the solution were measured. Very obvious characteristic fluorescence peaks were observed at 898 and 1058 nm. Based on Judd-Ofelt theory, three intensity parameters were obtained: Omega(2) = 4.9 x 10(-20) cm(2), Omega(4) = 5.1 x 10(-20) cm(2) and Omega(6) = 2.5 x 10(-20) cm(2). Line strengths S-cal, oscillator strengths f(cal), radiative transition probabilities A(ed), radiative lifetimes tau(r) and branch ratios beta were calculated too. The measured lifetime tau of 1058 nm peak is 460 mu s, and that of 898 nm 505 mu s. Comparison between theoretically computed radiative lifetime tau(r)(682 mu s) and the measured lifetime indicates that the non-radiative transition probability of the solution is very low and the fluorescence quantum efficiency very high. High values of three intensity parameters prove the high asymmetric surroundings of Nd3+, which is important for Nd3+ to absorb the excitation energy. Spectropic quality factor Omega(4)/Omega(6) > 1 makes radiation at 898 nm stronger than at 1058 nm.

梯度补偿法控温晶体的高功率绿光激光器

研究了平均功率超过30 W的稳定高效全固态绿光激光器,分析得出影响全固态腔内倍频激光器倍频效率和输出稳定性的主要因素是倍频晶体局部温升造成的相位失配和热透镜效应,采用温度梯度补偿控温法对大尺寸倍频晶体进行温度控制,降低激光器工作中倍频晶体内外温度梯度从而有效地克服因晶体局部温升造成的倍频相位匹配角失配和热透镜效应。采用三条60 W的半导体激光二极管阵列板条侧面抽运Nd:YAG激光增益介质棒,采用声光调Q,平凹直腔和腔内倍频结构配合温度梯度补偿控温法对大尺寸倍频晶体进行温度控制,得到了稳定高效的532 nm

输出高重复频率脉冲列的全固态激光器

报道了利用声光振幅调制锁模的方法，在激光二极管端面抽运Nd：YVO4激光器上获得320MHz高重复频率脉冲列的实验结果。实验采用平一平腔结构，腔长452mm，耦合输出镜透过率为3．6％。所用声光介质为熔融石英晶体，以铌酸锂作换能器，在驱动功率4．5W时，对1064nm波长衍射效率为50，相应的调制深度为0．31。在最佳锁模状态下，激光二极管抽运功率为3．5W，此时激光平均输出功率为15mw。示波器记录脉冲宽度680ps，实测光束质量因子M^2小于1．5。并在实验基础上对激光器工作的稳定性进行了分析，结果表

采用国产双包层光纤的声光调Q激光器

实验报道采用我国自行设计的大模场掺镱双包层光纤，利用简单声光调Q装置，成功实现调Q运转；在1－50kHz调制频率下获得了百纳秒的调Q脉冲，其输出光束质量因子大约为2。当重复频率为1kHz时，获得了脉冲宽度为132ns，能量0.93mJ。同时实验中观察到的调Q脉冲常出现一点锁模现象，针对这一现象进行了讨论。

大模场面积光纤激光器79．4W单横模输出

abstract {A large-mode-area (LMA) multimode fiber before and after coiling was studied contrastively in the experiment. Single-transverse-mode output was achieved when the fiber laser was coiled around a mandrel of 65 mm radius. After coiling, beam quality factor of the laser dropped from 1.24 to 1.06 and slope efficiency dropped from 64.7% to 54.3%. When the launched pump power was 149 W, the corresponding output power was 94.7 W and 79.4 W, respectively. However, the brightness of the coiled fiber laser was 1.15 times that of the uncoiled. Coiled modal losses of different modes were also calculated for the fiber employed in the experiment. The measured results agree well with the calculated ones.}

弯曲直径对多模光纤激光器输出性能的影响

大模场面积(LMA)多模光纤激光器的输出性能与光纤的弯曲程度有关。为研究两者之间的关系，在光纤不同弯曲直径下，对多模光纤激光器的输出性能进行了实验测量和理论计算。采用刀口法测量了不同弯曲直径下的激光光束质量因子M2，并对每种情况下光纤激光器的斜率效率进行了测量。光纤弯曲直径分别为285 mm,195 mm和130 mm时，多模光纤激光器光束质量因子M2为2.88,1.82和1.67，斜率效率为39%,35%和34%。另外，对于实验所采用的大模场面积多模光纤，理论计算了各模式损耗与光纤弯曲直径的关系。

大模场面积光纤激光器拉锥法模式选择

大模场面积(LMA)光纤激光器的光束质量通常比单模光纤激光器的光束质量差。采用光纤拉锥的方法进行模式选择,从而提高大模场直径光纤激光器的光束质量。拉锥区距光纤激光器的输出端约5 mm,纤芯最小为9 μm,约为未拉锥部分纤芯直径26 μm的1/3。实验研究表明,在拉锥后,光纤激光器的光束质量因子M2由3.50减小为1.81,相应的斜率效率由63.6%减小为51.1%。虽然拉锥后最大输出功率减少了约19.8%,但其亮度增大为拉锥前的3倍。

一种基于衍射光栅光束质量M^2因子的实时检测技术

提出了一种新的光束质量膨因子实时检测技术，利用一个普通正交衍射光栅组将一束待测激光束分成3×3共9路光，并利用光路调整器使9路光束通过不同的光程后有序地排列在CCD相机的探测面上，并使得各路光的光程差分布在束腰附近两倍瑞利距离内，从而可利用单一CCD探测面来同时获取待测光束多个位置上的光斑图样。再利用二阶矩理论求出各个位置上的光束束宽，通过曲线拟合进而实现光束质量的实时检测。结果表明，对于连续He-Ne激光器的输出光束，采用实时检测技术得到的测量结果与用传统方法得到的结果基本一致。

Highly efficient diode side-pumped Nd : YAG ceramic laser with 210W output power

We developed a highly efficient diode side-pumped Nd:YAG ceramic laser with a diffusive reflector as an optical pump cavity. A maximum output power of 211.6W was obtained with an optical -to- optical conversion efficiency of 48.7%. This corresponds to the highest conversion efficiency in the side-pumped ceramic rod. Thermal effects of the Nd:YAG ceramic rod were analyzed in detail through the measurements of laser output powers and beam profiles near the critically unstable region. A M-2 beam quality factor of 18.7 was obtained at the maximum laser output power. (c) 2006 Elsevier Ltd. All rights reserved.

Stable pulse-compressed acousto-optic Q-switched fiber laser

A novel acousto-optic switch operation by a simple laser-diode pumped acousto-optic, Q-switched, ytterbium-doped, double-clad fiber laser is reported. Stable compressed Q-switched sub-40 ns pulses with a beam quality factor (M-2 = 2) are achieved at the repetition rate of 1-50 kHz. Q-switched pulses of similar to 20 mu J pulse energy and 35 as pulse width are obtained at the repetition rate of 50 kHz. Finally, a reasonable explanation of the novel Q-switched operation is presented. (c) 2007 Optical Society of America.

InnoSlab混合腔输出光束质量的理论研究

对InnoSlab Laser用混合腔的输出光束质量问题从热透镜效应和腔镜的不对准两个方面的影响进行理论分析,并从远场光强分布、远场发散角、光腰半径、光束质量因子M2值和桶中功率曲线等几个角度进行了讨论,特别是离轴非稳腔方向上腔镜倾斜对光束质量的影响,利用M2值和PIB曲线两个参数共同评价非稳腔的光束质量,对目前并无统一标准的非稳腔光束质量评价问题提供了有意义的参考.

Continuous-wave and Q-switched operation of a resonantly pumped Ho:YAlO3 laser

We demonstrated continuous-wave ( CW) and Q-switched operation of a room-temperature Ho: YAlO3 laser that is resonantly end-pumped by a diode-pumped Tm: YLF laser at 1.91 mu m. The CW Ho: YAlO3 laser generated 5.5 W of linearly polarized (E parallel to c) output at 2118 nm with beam quality factor of M-2 approximate to 1.1 for an incident pump power of 13.8 W, corresponding to optical-to-optical conversion efficiency of 40%. Up to 1-mJ energy per pulse at pulse repetition frequency (PRF) of 5 kHz, and the maximum average power of 5.3-W with FWHM pulse duration of 30.5 ns at 20 kHz were achieved in Q-switched mode. (C) 2008 Optical Society of America.

Thermoelastic dissipation in MEMS/NEMS flexural mode resonators.

Understanding the energy dissipation mechanisms in single-crystal silicon MEMS/NEMS resonators are particularly important to maximizing an important figure of merit relevant for miniature sensor and signal processing applications: the Quality factor (Q) of resonance. This paper discusses thermoelastic dissipation (TED) as the dominant internal-friction mechanism in flexural mode MEMS/NEMS resonators. Criteria for optimizing the geometrical design of flexural mode MEMS/NEMS resonators are theoretically established with a view towards minimizing the TED for single-crystal silicon MEMS/NEMS flexural mode resonators.