The potential use of 241Am as proliferation resistant burnable poison

This paper discusses the use of 141Am as proliferation resistant burnable poison for light water reactors. Homogeneous addition of small (less than 1 %) amounts of 241Am to the conventional LWR fuel results in significant increase in 238Pu/Pu ratio in the discharged fuel improving its proliferation resistance. Moreover, 241Am, admixed to the fuel, acts as burnable absorber allowing for substantial reduction in conventional reactivity control means without notable fuel cycle length penalty. This is possible due to favourable characteristics of 241Am transmutation chain. The fuel cycle length penalty of introducing 241Am into the core is evaluated and discussed, as well as the impact of He production in the fuel pins and degradation of reactivity feedback coefficients. Proliferation resistance and reactivity control features related to the use of 241Am are compared to those of using 237Np, which has also been suggested as an additive to the conventional fuel in order to improve its proliferation resistance. It was found that 241Am admixture is more favourable than 237Np admixture because of the smaller fuel cycle length penalty and higher burnable poison savings.

A combined nonfertile and UO2 PWR fuel assembly for actinide waste minimization

A new combined Non Fertile and Uranium (CONFU) fuel assembly is proposed to limit the actinides that need long-term high-level waste storage from the pressurized water reactor (PWR) fuel cycle. In the CONFU assembly concept, ∼20% of the UO2 fuel pins are replaced with fertile free fuel hosting the transuranic elements (TRUs) generated in the previous cycle. This leads to a fuel cycle sustainable with respect to net TRU generation, and the amount and radiotoxicity of the nuclear waste can be significantly reduced in comparison with the conventional once-through UO2 fuel cycle. It is shown that under the constraints of acceptable power peaking limits, the CONFU assembly exhibits negative reactivity feedback coefficients comparable in values to those of the reference UO2 fuel. Feasibility of the PWR core operation and control with complete TRU recycle has been shown based on full-core three-dimensional neutronic simulation. However, gradual buildup of small amounts of Cm and Cf challenges fuel reprocessing and fabrication due to the high spontaneous fission rates of these nuclides and heat generation by some Pu, Am, and Cm isotopes. Feasibility of the processing steps becomes more attainable if the time between discharge and reprocessing is 20 yr or longer.

Influência da água no sistema de autolimpeza das esteiras condutoras de cortes sobre a qualidade microbiológica da carne de frango

Pós-graduação em Medicina Veterinária - FCAV

Calculation of the eigenfunctions of the two-group neutron diffusion equation and application to modal decomposition of BWR instabilities

In this thesis, numerical methods aiming at determining the eigenfunctions, their adjoint and the corresponding eigenvalues of the two-group neutron diffusion equations representing any heterogeneous system are investigated. First, the classical power iteration method is modified so that the calculation of modes higher than the fundamental mode is possible. Thereafter, the Explicitly-Restarted Arnoldi method, belonging to the class of Krylov subspace methods, is touched upon. Although the modified power iteration method is a computationally-expensive algorithm, its main advantage is its robustness, i.e. the method always converges to the desired eigenfunctions without any need from the user to set up any parameter in the algorithm. On the other hand, the Arnoldi method, which requires some parameters to be defined by the user, is a very efficient method for calculating eigenfunctions of large sparse system of equations with a minimum computational effort. These methods are thereafter used for off-line analysis of the stability of Boiling Water Reactors. Since several oscillation modes are usually excited (global and regional oscillations) when unstable conditions are encountered, the characterization of the stability of the reactor using for instance the Decay Ratio as a stability indicator might be difficult if the contribution from each of the modes are not separated from each other. Such a modal decomposition is applied to a stability test performed at the Swedish Ringhals-1 unit in September 2002, after the use of the Arnoldi method for pre-calculating the different eigenmodes of the neutron flux throughout the reactor. The modal decomposition clearly demonstrates the excitation of both the global and regional oscillations. Furthermore, such oscillations are found to be intermittent with a time-varying phase shift between the first and second azimuthal modes.

Accident Management Actions In An Upper-Head Small-Break Loss-Of-Coolant Accident With High-Pressure Safety Injection Failed

Since the Three Mile Island accident, an important focus of pressurized water reactor (PWR) transient analyses has been a small-break loss-of-coolant accident (SBLOCA). In 2002, the discovery of thinning of the vessel head wall at the Davis Besse nuclear power plant reactor indicated the possibility of an SBLOCA in the upper head of the reactor vessel as a result of circumferential cracking of a control rod drive mechanism penetration nozzle - which has cast even greater importance on the study of SBLOCAs. Several experimental tests have been performed at the Large Scale Test Facility to simulate the behavior of a PWR during an upper-head SBLOCA. The last of these tests, Organisation for Economic Co-operation and Development Nuclear Energy Agency Rig of Safety Assessment (OECD/NEA ROSA) Test 6.1, was performed in 2005. This test was simulated with the TRACE 5.0 code, and good agreement with the experimental results was obtained. Additionally, a broad analysis of an upper-head SBLOCA with high-pressure safety injection failed in a Westinghouse PWR was performed taking into account different accident management actions and conditions in order to check their suitability. This issue has been analyzed also in the framework of the OECD/NEA ROSA project and the Code Applications and Maintenance Program (CAMP). The main conclusion is that the current emergency operating procedures for Westinghouse reactor design are adequate for these kinds of sequences, and they do not need to be modified.

Assessment of CTF boiling transition and critical heat flux modeling capabilities using the OECD/NRC BFBT and PSBT benchmark databases

The need to refine models for best-estimate calculations, based on good-quality experimental data, has been expressed in many recent meetings in the field of nuclear applications. The modeling needs arising in this respect should not be limited to the currently available macroscopic methods but should be extended to next-generation analysis techniques that focus on more microscopic processes. One of the most valuable databases identified for the thermalhydraulics modeling was developed by the Nuclear Power Engineering Corporation (NUPEC), Japan. From 1987 to 1995, NUPEC performed steady-state and transient critical power and departure from nucleate boiling (DNB) test series based on the equivalent full-size mock-ups. Considering the reliability not only of the measured data, but also other relevant parameters such as the system pressure, inlet sub-cooling and rod surface temperature, these test series supplied the first substantial database for the development of truly mechanistic and consistent models for boiling transition and critical heat flux. Over the last few years the Pennsylvania State University (PSU) under the sponsorship of the U.S. Nuclear Regulatory Commission (NRC) has prepared, organized, conducted and summarized the OECD/NRC Full-size Fine-mesh Bundle Tests (BFBT) Benchmark. The international benchmark activities have been conducted in cooperation with the Nuclear Energy Agency/Organization for Economic Co-operation and Development (NEA/OECD) and Japan Nuclear Energy Safety (JNES) organization, Japan. Consequently, the JNES has made available the Boiling Water Reactor (BWR) NUPEC database for the purposes of the benchmark. Based on the success of the OECD/NRC BFBT benchmark the JNES has decided to release also the data based on the NUPEC Pressurized Water Reactor (PWR) subchannel and bundle tests for another follow-up international benchmark entitled OECD/NRC PWR Subchannel and Bundle Tests (PSBT) benchmark. This paper presents an application of the joint Penn State University/Technical University of Madrid (UPM) version of the well-known subchannel code COBRA-TF, namely CTF, to the critical power and departure from nucleate boiling (DNB) exercises of the OECD/NRC BFBT and PSBT benchmarks

Neighborhood-corrected interface discontinuity factors for multi-group pin-by-pin diffusion calculations for LWR

Performing three-dimensional pin-by-pin full core calculations based on an improved solution of the multi-group diffusion equation is an affordable option nowadays to compute accurate local safety parameters for light water reactors. Since a transport approximation is solved, appropriate correction factors, such as interface discontinuity factors, are required to nearly reproduce the fully heterogeneous transport solution. Calculating exact pin-by-pin discontinuity factors requires the knowledge of the heterogeneous neutron flux distribution, which depends on the boundary conditions of the pin-cell as well as the local variables along the nuclear reactor operation. As a consequence, it is impractical to compute them for each possible configuration; however, inaccurate correction factors are one major source of error in core analysis when using multi-group diffusion theory. An alternative to generate accurate pin-by-pin interface discontinuity factors is to build a functional-fitting that allows incorporating the environment dependence in the computed values. This paper suggests a methodology to consider the neighborhood effect based on the Analytic Coarse-Mesh Finite Difference method for the multi-group diffusion equation. It has been applied to both definitions of interface discontinuity factors, the one based on the Generalized Equivalence Theory and the one based on Black-Box Homogenization, and for different few energy groups structures. Conclusions are drawn over the optimal functional-fitting and demonstrative results are obtained with the multi-group pin-by-pin diffusion code COBAYA3 for representative PWR configurations.

Control rod drop surveillance using two friction coefficients

In the case of large burnup, a control rod (CR) guide tube in the pressurized water reactor of a commercial nuclear power plant might bend. As a consequence, a CR drop experiment may indicate an event of a CR partially inserted and whether the CR should be deemed inoperable. Early prevention of such an event can be achieved by measuring two friction coefficients: the hydraulic coefficient and the sliding coefficient. The hydraulic coefficient hardly changes, so that the curvature of the guide tube can only be detected thanks to a variation of the sliding coefficient. A simple model for the CR drop is established and validated with CR drop experiments. If tmx denotes the instant of CR maximum velocity, a linear relationship between (tmx)_2 and the sliding coefficient is found.

Simulación del accidente de SGTR en un PWR-W con TRACE para distintas metodologías de análisis determinista de seguridad

A Steam Generator Tube Rupture (SGTR) in a Pressurized Water Reactor (PWR) can lead to an atmospheric release bypassing the containment via the secondary system and exiting though the Pressurized Operating Relief Valves of the affected Steam Generator. That is why SGTR historically have been treated in a special way in the different Deterministic Safety Analysis (DSA), focusing on the radioactive release more than the possibility of core damage, as it is done in the other Loss of Coolant Accidents(LOCAs).

In situ surveillance of capacitive pressure transmitter dynamic poles

In this work, a methodology is proposed to find the dynamic poles of a capacitive pressure transmitter in order to enhance and extend the online surveillance of this type of sensor based on the response time measurement by applying noise analysis techniques and the dynamic data system procedure. Several measurements taken from a pressurized water reactor have been analyzed. The methodology proposes an autoregressive fit whose order is determined by the sensor dynamic poles. Nevertheless, the signals that have been analyzed could not be filtered properly in order to remove the plant noise; thus, this was considered as an additional pair of complex conjugate poles. With this methodology we have come up with the numerical value of the sensor second real pole in spite of its low influence on the sensor dynamic response. This opens up a more accurate online sensor surveillance since the previous methods were achieved by considering one real pole only.

AR modelling and DDS for in situ surveillance of capacitive pressure transmitters

In this work, a methodology is proposed to find the dynamics poles of a capacitive pressure transmitter in order to enhance and extend the on line surveillance of this type of sensors based on the response time measurement by applying noise analysis techniques and the Dynamic Data System. Several measurements have been analyzed taken from a Pressurized Water Reactor. The methodology proposes an autoregressive fit whose order is determined by the sensor dynamics poles. Nevertheless, the signals that have been analyzed, could not be filtered properly in order to remove the plant noise, thus, this was considered as an additional pair of complex conjugate poles. With this methodology we have come up with the numerical value of the sensor second real pole in spite of its low influence on the sensor dynamic response. This opens up a more accurate on line sensor surveillance since the previous methods were achieved by considering one real pole only.

Methodologies for an improved prediction of the isotopic content in high burnup samples. Application to Vandellos-II reactor core

Fuel cycles are designed with the aim of obtaining the highest amount of energy possible. Since higher burnup values are reached, it is necessary to improve our disposal designs, traditionally based on the conservative assumption that they contain fresh fuel. The criticality calculations involved must consider burnup by making the most of the experimental and computational capabilities developed, respectively, to measure and predict the isotopic content of the spent nuclear fuel. These high burnup scenarios encourage a review of the computational tools to find out possible weaknesses in the nuclear data libraries, in the methodologies applied and their applicability range. Experimental measurements of the spent nuclear fuel provide the perfect framework to benchmark the most well-known and established codes, both in the industry and academic research activity. For the present paper, SCALE 6.0/TRITON and MONTEBURNS 2.0 have been chosen to follow the isotopic content of four samples irradiated in the Spanish Vandellós-II pressurized water reactor up to burnup values ranging from 40 GWd/MTU to 75 GWd/MTU. By comparison with the experimental data reported for these samples, we can probe the applicability of these codes to deal with high burnup problems. We have developed new computational tools within MONTENBURNS 2.0. They make possible to handle an irradiation history that includes geometrical and positional changes of the samples within the reactor core. This paper describes the irradiation scenario against which the mentioned codes and our capabilities are to be benchmarked.

Aplicación de la metodología ISA al análisis de la secuencia de pérdida del sistema de agua de refrigeración de componentes en una central nuclear con reactor de agua a presión

La metodología Integrated Safety Analysis (ISA), desarrollada en el área de Modelación y Simulación (MOSI) del Consejo de Seguridad Nuclear (CSN), es un método de Análisis Integrado de Seguridad que está siendo evaluado y analizado mediante diversas aplicaciones impulsadas por el CSN; el análisis integrado de seguridad, combina las técnicas evolucionadas de los análisis de seguridad al uso: deterministas y probabilistas. Se considera adecuado para sustentar la Regulación Informada por el Riesgo (RIR), actual enfoque dado a la seguridad nuclear y que está siendo desarrollado y aplicado en todo el mundo. En este contexto se enmarcan, los proyectos Safety Margin Action Plan (SMAP) y Safety Margin Assessment Application (SM2A), impulsados por el Comité para la Seguridad de las Instalaciones Nucleares (CSNI) de la Agencia de la Energía Nuclear (NEA) de la Organización para la Cooperación y el Desarrollo Económicos (OCDE) en el desarrollo del enfoque adecuado para el uso de las metodologías integradas en la evaluación del cambio en los márgenes de seguridad debidos a cambios en las condiciones de las centrales nucleares. El comité constituye un foro para el intercambio de información técnica y de colaboración entre las organizaciones miembro, que aportan sus propias ideas en investigación, desarrollo e ingeniería. La propuesta del CSN es la aplicación de la metodología ISA, especialmente adecuada para el análisis según el enfoque desarrollado en el proyecto SMAP que pretende obtener los valores best-estimate con incertidumbre de las variables de seguridad que son comparadas con los límites de seguridad, para obtener la frecuencia con la que éstos límites son superados. La ventaja que ofrece la ISA es que permite el análisis selectivo y discreto de los rangos de los parámetros inciertos que tienen mayor influencia en la superación de los límites de seguridad, o frecuencia de excedencia del límite, permitiendo así evaluar los cambios producidos por variaciones en el diseño u operación de la central que serían imperceptibles o complicados de cuantificar con otro tipo de metodologías. La ISA se engloba dentro de las metodologías de APS dinámico discreto que utilizan la generación de árboles de sucesos dinámicos (DET) y se basa en la Theory of Stimulated Dynamics (TSD), teoría de fiabilidad dinámica simplificada que permite la cuantificación del riesgo de cada una de las secuencias. Con la ISA se modelan y simulan todas las interacciones relevantes en una central: diseño, condiciones de operación, mantenimiento, actuaciones de los operadores, eventos estocásticos, etc. Por ello requiere la integración de códigos de: simulación termohidráulica y procedimientos de operación; delineación de árboles de sucesos; cuantificación de árboles de fallos y sucesos; tratamiento de incertidumbres e integración del riesgo. La tesis contiene la aplicación de la metodología ISA al análisis integrado del suceso iniciador de la pérdida del sistema de refrigeración de componentes (CCWS) que genera secuencias de pérdida de refrigerante del reactor a través de los sellos de las bombas principales del circuito de refrigerante del reactor (SLOCA). Se utiliza para probar el cambio en los márgenes, con respecto al límite de la máxima temperatura de pico de vaina (1477 K), que sería posible en virtud de un potencial aumento de potencia del 10 % en el reactor de agua a presión de la C.N. Zion. El trabajo realizado para la consecución de la tesis, fruto de la colaboración de la Escuela Técnica Superior de Ingenieros de Minas y Energía y la empresa de soluciones tecnológicas Ekergy Software S.L. (NFQ Solutions) con el área MOSI del CSN, ha sido la base para la contribución del CSN en el ejercicio SM2A. Este ejercicio ha sido utilizado como evaluación del desarrollo de algunas de las ideas, sugerencias, y los algoritmos detrás de la metodología ISA. Como resultado se ha obtenido un ligero aumento de la frecuencia de excedencia del daño (DEF) provocado por el aumento de potencia. Este resultado demuestra la viabilidad de la metodología ISA para obtener medidas de las variaciones en los márgenes de seguridad que han sido provocadas por modificaciones en la planta. También se ha mostrado que es especialmente adecuada en escenarios donde los eventos estocásticos o las actuaciones de recuperación o mitigación de los operadores pueden tener un papel relevante en el riesgo. Los resultados obtenidos no tienen validez más allá de la de mostrar la viabilidad de la metodología ISA. La central nuclear en la que se aplica el estudio está clausurada y la información relativa a sus análisis de seguridad es deficiente, por lo que han sido necesarias asunciones sin comprobación o aproximaciones basadas en estudios genéricos o de otras plantas. Se han establecido tres fases en el proceso de análisis: primero, obtención del árbol de sucesos dinámico de referencia; segundo, análisis de incertidumbres y obtención de los dominios de daño; y tercero, cuantificación del riesgo. Se han mostrado diversas aplicaciones de la metodología y ventajas que presenta frente al APS clásico. También se ha contribuido al desarrollo del prototipo de herramienta para la aplicación de la metodología ISA (SCAIS). ABSTRACT The Integrated Safety Analysis methodology (ISA), developed by the Consejo de Seguridad Nuclear (CSN), is being assessed in various applications encouraged by CSN. An Integrated Safety Analysis merges the evolved techniques of the usually applied safety analysis methodologies; deterministic and probabilistic. It is considered as a suitable tool for assessing risk in a Risk Informed Regulation framework, the approach under development that is being adopted on Nuclear Safety around the world. In this policy framework, the projects Safety Margin Action Plan (SMAP) and Safety Margin Assessment Application (SM2A), set up by the Committee on the Safety of Nuclear Installations (CSNI) of the Nuclear Energy Agency within the Organization for Economic Co-operation and Development (OECD), were aimed to obtain a methodology and its application for the integration of risk and safety margins in the assessment of the changes to the overall safety as a result of changes in the nuclear plant condition. The committee provides a forum for the exchange of technical information and cooperation among member organizations which contribute their respective approaches in research, development and engineering. The ISA methodology, proposed by CSN, specially fits with the SMAP approach that aims at obtaining Best Estimate Plus Uncertainty values of the safety variables to be compared with the safety limits. This makes it possible to obtain the exceedance frequencies of the safety limit. The ISA has the advantage over other methods of allowing the specific and discrete evaluation of the most influential uncertain parameters in the limit exceedance frequency. In this way the changes due to design or operation variation, imperceptibles or complicated to by quantified by other methods, are correctly evaluated. The ISA methodology is one of the discrete methodologies of the Dynamic PSA framework that uses the generation of dynamic event trees (DET). It is based on the Theory of Stimulated Dynamics (TSD), a simplified version of the theory of Probabilistic Dynamics that allows the risk quantification. The ISA models and simulates all the important interactions in a Nuclear Power Plant; design, operating conditions, maintenance, human actuations, stochastic events, etc. In order to that, it requires the integration of codes to obtain: Thermohydraulic and human actuations; Even trees delineation; Fault Trees and Event Trees quantification; Uncertainty analysis and risk assessment. This written dissertation narrates the application of the ISA methodology to the initiating event of the Loss of the Component Cooling System (CCWS) generating sequences of loss of reactor coolant through the seals of the reactor coolant pump (SLOCA). It is used to test the change in margins with respect to the maximum clad temperature limit (1477 K) that would be possible under a potential 10 % power up-rate effected in the pressurized water reactor of Zion NPP. The work done to achieve the thesis, fruit of the collaborative agreement of the School of Mining and Energy Engineering and the company of technological solutions Ekergy Software S.L. (NFQ Solutions) with de specialized modeling and simulation branch of the CSN, has been the basis for the contribution of the CSN in the exercise SM2A. This exercise has been used as an assessment of the development of some of the ideas, suggestions, and algorithms behind the ISA methodology. It has been obtained a slight increase in the Damage Exceedance Frequency (DEF) caused by the power up-rate. This result shows that ISA methodology allows quantifying the safety margin change when design modifications are performed in a NPP and is specially suitable for scenarios where stochastic events or human responses have an important role to prevent or mitigate the accidental consequences and the total risk. The results do not have any validity out of showing the viability of the methodology ISA. Zion NPP was retired and information of its safety analysis is scarce, so assumptions without verification or approximations based on generic studies have been required. Three phases are established in the analysis process: first, obtaining the reference dynamic event tree; second, uncertainty analysis and obtaining the damage domains; third, risk quantification. There have been shown various applications of the methodology and advantages over the classical PSA. It has also contributed to the development of the prototype tool for the implementation of the ISA methodology (SCAIS).

Estudo de modelos para o comportamento a altas queimas de varetas combustíveis de reatores a água leve pressurizada

Este trabalho tem como objetivo estudar as modificações introduzidas, ao longo de sucessivas versões, nos modelos empíricos do programa computacional FRAPCON utilizado para a simulação do comportamento sob irradiação de varetas combustíveis de Reatores a Água Leve Pressurizada (Pressurized Water Reactor - PWR) em regime de estado estacionário e sob condições de alta queima. No estudo, foram analisados os modelos empíricos utilizados pelo FRAPCON e que são apresentados em sua documentação oficial. Um estudo bibliográfico foi conduzido sobre os efeitos da alta queima em combustíveis nucleares visando melhorar o entendimento dos modelos utilizados pelo FRAPCON nestas condições. Foram feitas simulações do comportamento sob irradiação de uma vareta combustível típica de um reator PWR utilizando as versões 3.3, 3.4 e 3.5 do FRAPCON. Os resultados apresentados pelas diferentes versões do programa foram comparados entre si de forma a verificar as consequências das mudanças de modelo nos parâmetros de saída do programa. Foi possível observar que as modificações introduzidas trouxeram diferenças significativas nos resultados de parâmetros térmicos e mecânicos da vareta combustível, principalmente quando se evoluiu da versão FRAPCON-3.3 para a versão FRAPCON-3.5. Nessa ultima versão, obteve-se menores temperaturas na vareta combustível, menores tensões e deformações no revestimento, menor espessura da camada de oxido formada no revestimento a altas queimas na vareta combustível.

Applicazioni degli acciai inossidabili in sistemi per la produzione di energia.

Questo elaborato ha lo scopo di esporre quelli che sono i vantaggi derivanti dall' utilizzo degli acciai inossidabili, specificando il tipo di componente e le ragioni della scelta, nei sistemi per la produzione di energia: dalle turbine, agli impianti nucleari, fino agli impianti che sfruttano le energie alternative (solare, eolica, geotermica, biogas). Inizialmente viene fornito un quadro generale sui differenti tipi di acciai inox (martensitici, ferritici, austenitici e duplex, con le relative proprietà, sottolineandone vantaggi e svantaggi), descrivendone anche i sistemi di designazione, con particolare attenzione alla norma AISI (American Iron and Steel Institute). Una volta messe in risalto queste caratteristiche, vengono esaminati e descritti diversi sistemi di produzione di energia in cui gli acciai inox trovano applicazione: si parte dalle turbine (idraulica, a vapore e a gas), spiegando i benefici nell'utilizzo di particolari categorie di acciai inox nella realizzazione di alcuni dei componenti per questi impianti. Vengono quindi esaminati gli impianti nucleari, partendo da quelli che utilizzano come moderatore e fluido refrigerante acqua naturale, ("PWR", Pressurized Water Reactor) e ("BWR", Boiling Water Reactor), fino a quelli che utilizzano invece acqua pesante ("CANDU", Canadian Deuterium Uranium Reactor), nonchè i reattori veloci ("FBR", Fast Breeding Reactor). Infine, vengono esaminate le applicazioni degli acciai inox, nei sistemi per la produzione di energia che, sfruttano fonti alternative (elencate in precedenza).