999 resultados para Pr-10
Resumo:
The structure and photoluminscence (PL) properties of Pr-implanted GaN thin films have been studied. RBS/channeling technique was used to explore the damage recovery at high annealing temperature and study the dependence of the radiation damage with ion implantation direction. A complete recovery of the ion implantation damage cannot be achieved at annealing temperatures up to 1050degreesC. It is found that the channeling implantation results in the decrease of the damage. The PL experimental results indicate that the PL efficiency increases exponentially with annealing temperature up to the maximum temperature of 1050degreesC. Moreover, the PL intensity is also seriously affected by ion implantation geometries. The PL intensity for the sample implanted along channeled direction is nearly 2 times more intense than that observed from the sample implanted along random direction. The thermal quenching of PL intensity from 10 to 300K for sample annealed at 1050degreesC is only 30%. (C) 2004 Elsevier B.V. All rights reserved.
Resumo:
本文内容包括Tb~(3+)、Pr~(3+)、Ce~(3+)的光氧化。研究了各种因素对氧化率或四价离子生成量的影响。在Tb~(3+)光氧化的基础上,建立了混合钇族稀土中Tb的光化学分析法及混合稀土中Tb的化学氧化分析方法。Tb~(3+)、Pr~(3+)的光氧化是开创性的工作,Tb的分析方法具有一定的应用价值。1 Ce~(3+)d HZO_3-HClO_4体系中的光氧化 用低压汞灯(254nm)、高压汞灯(366nm)和氩离子激光器(351/364nm, 458 nm, 477nm, 502 nm, 514, nm)光辐照Ce~(3+)-HZO_3-HClO_4溶液,Ce~(3+)发生光氧化反应,生成Ce(ZO_3)_4沉淀 。在低压汞灯254 nm波段可获得较高的氧化率,具它波段下的氧化率低,以低压汞灯为光源辐照。研究了温度、光强、酸度、Ce~(3+)初始浓度及辐照时间对氧化率的影响。降低酸度,选择较高的温度和较大的光强,有利于Ce~(3+)的光氧化。2 Tb~(3+)在KIO_4-KOH体系中的光氧化 用高压汞灯(366nm)光辐照Tb~(3+)-KIO_4-KOH溶液,首次实现了Tb~(3+)的光氧化。研究了碱度、络合剂浓度,Tb~(3+)初始浓度、辐照面积,光强和辐照时间等因素对Tb~(4+)生成的影响。测定了Tb(IV)/Rb(III)的氧化还原电势。适宜的KOH浓度应大于0.3M,KIO_4的浓度要比Tb~(3+)初始浓度大几个数量级。当KOH=0.6M, KIO_4=0.22M, 温度为13 ℃时。E_(Tb(IV)/Tb(III))=0.68优,生成的Tb~(4+)可溶性络离子为红棕色,最大吸收峰在420nm附近,比较稳定。3 用光氧化法分析钇族混合稀土中的Tb 根据Tb~(3+)在KIO_4-KOH体系中的光氧化反应,建立了钇族混合稀土中Tb的分光光度分析方法。在高压汞灯366nm的光辐照不无色的Tb~(3+)转变为红棕色的Tb~(4+),其谱带的吸收峰值在420nm,其它三价钇族稀土无此反应,故无千扰,在Tb的分析浓度范围为1*10~(-5)M - 1*10~(-3)M时,符合Beer定律,Tb在钇族混合稀土中含量的分析最低限为0.2%。此方法可用于萃取钇族稀土过程中Tb的分析,方法简便快速。4 用化学氧化法分析混合稀土中的Tb 根据Tb~(3+)在KIO_4-KOH-K_2S_2O_8体系中的氧化反应,建立了混和稀土中Tb的分光光度分析方法。Tb~(3+)-KzO_4-KOH-K_2S_2O_8溶液加热,Tb~(3+)被氧化的Tb~(4+),其颜色由无色转变为红棕色,最大吸收峰在420nm。Ce~(3+)加入KIO_4-KOH溶液后,立即被完全氧化为Ce~(4+), Ce~(4+)在420nm也有吸收,其干扰可以在本底中排除,其它三价稀土离子在此体系中不能发生氧化反应,故无干扰。在Tb的分析浓度范围为5*10~(-5)-5*10~(-4)M时,符合Beer定律,Tb在混合稀土中含量分析的最低限为1%。此方法可用于萃取稀土过程中Tb的分析和监控,方法简便快速。5 Pr~(3+)在KZO_4-KOH体系中的光氧化用高压汞灯光辐照Pr~(3+)-KZO_4-KOH溶液,首次实现了Pr~(3+)的光氧化。生成的Pr~(4+)为棕褐色,最大吸收峰在400nm附近,稳定性较差,在水溶液中发生自还原反应。按Pr~(4+)在400nm的吸收峰值,研究了辐照时间,Pr~(3+)初始浓度,KOH浓度、KZO_4浓度及Ce~(4+)共存时对Pr~9(4+)生成的影响。相应增加KOH及KZO_4用量,有利于Pr~(4+)的生成,Ce~(4+)对Pr~(3+)的光氧化无所谓的“带同氧化作用”。
Resumo:
通过96 Ru( 4 0 Ca ,ln2p)反应 ,采用氦喷嘴带传输系统和X γ与γ γ符合测量方法 ,首次建议了133Sm的简单的 (EC + β+)衰变纲图 .由于Ru靶中含有98— 10 2 Ru的成分 ,同时产生了133Pr,并首次测定了133Pr的 1 1 / 2 - 同质异能态的寿命为( 1 .1± 0 .2 )s.用单粒子模型提取了131,133,135 ,137Pr的 1 1 / 2 - 同质异能态的约化跃迁几率的实验值 ,并与Weisscopf近似估计进行了比较 .
Resumo:
在相对论平均场框架下研究了Pr同位素链中中子和质子滴线核的可能位置及相关性质 .对效应的处理采用了BCS方法 ,并使用了与同位素有关的对力常数 ,对不成对的核子采用了‘阻塞法’ ,考虑了核的轴对称形变 .计算结果表明 ,对不同物理量的研究都可得到185 Pr为同位素链中丰中子边最后一个稳定核 .而在丰质子边 ,采用本方法很难确定质子滴线核的位置 .原因是由于在丰质子边随着A的减少 ,费米面比丰中子边的费米面更快地趋于连续态 ,BCS方法不再成立 ,并须考虑束缚态和连续态的耦合 .
Resumo:
A series of near-infrared (NIR) luminescent complexes Ho(dbm)(3)L and Pr(dbm)(3)L [where dbm = dibenzoylmethane; L = 1,10-phenanthroline (phen), 2,2'-bipyridine (bipy), or triphenyl phosphate oxide (TPPO)] were synthesized. Their elemental analyses, crystal structures, fluorescence spectra and luminescent lifetimes were successfully investigated.
Resumo:
New near-infrared-luminescent mesoporous materials were prepared by linking ternary lanthanide (Er3+, Nd3+, Yb3+, Sm3+, Pr3+) complexes to the ordered mesoporous MCM-41 through a functionalized 1,10-phenanthroline (phen) group 5-(N,N-bis-3-(triethoxysilyl)propyl)ureyl-1,10-phenanthroline. The resulting materials (denoted as Ln(hfth)(3)phen-M41 and Pr(tfnb)(3)phen-M41; Ln=Er, Yb, Nd, Sm; hfth = 4,4,5,5,6,6,6-heptafluoro-1-(2-thienyl)hexane-1,3-dionate; tfnb = 4,4,4-trifluoro-1-(2-naphthyl)- 1, 3-butanedionate) were characterized by powder X-ray diffraction, N-2 adsorption/desorption, and elemental analysis. Luminescence spectra of these lanthanide-complex functionalized materials were recorded, and the luminescence decay times were measured. Upon excitation at the absorption of the organic ligands, all these materials show the characteristic NIR luminescence of the corresponding lanthanide (Er3+, Nd3+, Yb3+, Sm3+, Pr3+) ions by sensitization from the organic ligands moiety. The good luminescent performances enable these NIR-luminescent mesoporous materials to have possible applications in optical amplification (operating at 1300 or 1500 nm), laser systems, or medical diagnostics.
Resumo:
Material formulated as Ce5.2Sm0.8-xPrxMo15-(delta) (x=0.08) was prepared by adding small amounts of Pr dopant in oxide Ce5.2SM0.8-xPrxMoO15-delta. Structural and electrical properties were investigated by means of X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FE-SEM) and AC impedance spectroscopy. The effect of small amounts of Pr on microstructure and electrical conductivity was discussed. It was showed that the material doped with Pr has a lot of dents and small openings, which provide channels for oxygen ions, resulting in lower grain boundary and total conductivity activation energy. Thus the corresponding grain boundary conductivity and total conductivity of the material were improved notably. The grain boundary conductivity of the material doped with Pr is 6.79 X 10(-3) S center dot cm(-1) at 500 degrees C, which is twice as large as that without Pr (5.61 X 10(-5) S center dot cm(-1)).
Resumo:
A multiphase model of metal ion speciation in human interstitial fluid was constructed and the effect of Pr(III) on Ca(II) speciation was studied. Results show that free Ca2+, [Ca(HCO3)], and [Ca(Lac)] are the main species of Ca(II). Because of the competition of Pr(III) for ligands with Ca(II), the percentages of free Ca2+, [Ca(Lac)], and [Ca(His)(Thr)H-3] increase gradually and the percentages of CaHPO4(aq) and [Ca(Cit)(His)H-2] decrease gradually with the increase in the total concentration of Pr(III). However, the percentages of [Ca(HCO3)] and CaCO3(aq) first increase and then begin to decrease when the total concentration of Pr(III) exceeds 6.070 x 10(-4) M.
Resumo:
A multi-phase model of Pr(III) speciation in human interstitial fluid was constructed and insoluble Pr(III) speciation was studied. When the total concentration of Pr(III) is below 8.401E-10 mol/L, soluble Pr(III) species are main species. With rising the total concentration of Pr(III), Pr(III) is firstly bound to phosphate to form precipitate of PrPO4, then bound to carbonate and another precipitate of Pr-2(CO3)(3) was obtained. When the total concentration is between 1.583E-9 mol/L and 4.000E-3 mol/L, the insoluble species are predominant Pr(III) species.
Resumo:
The stability constant for complex of Pr(III) with adrenaline has been determined by potentiometric titration under biological conditions (37 degrees C and 0.15 mol/L NaCl). The absorption spectra of the Pr(III)-adrenaline system exhibit characteristic bands of Pr(III) at lower pH values. However, the charge transfer band which is due to the coordination of Pr(III) with adrenaline has been observed at higher pH values.
Resumo:
The relationship between bond valence and bond covalency in RMn2O5 (R = La, Pr, Nd, Sm, Eu) has been investigated by a semiempirical method. This method is the generalization of the dielectric description theory of Phillips, Van Vechten, Levine and Tanaka scheme. The results indicate that larger valences usually result in higher bond covalencies, in good agreement with the point that the excess charge in the bonding region is the origin of formation of bond covalency. Other factors, such as oxidation state of elements, only make a small contribution to bond covalency.
Resumo:
Single crystals of KLnN(Ln=La, Ce, Pr, Nd, Sm) can be grown in water solution with pH approximate to 1 similar to 2 at about 40 degrees C. Crystals of KLnN (Ln=La, Ce, Pr, Nd) are orthorhombic with space group Fdd2. KPrN crystal was grwon and its crystal structure was determined for the first time. The KPrN crystal parameters obtained by the direct method are as follows: a=21.411(3) Angstrom, b=11.2210(10)Angstrom, c=12.208(2) Angstrom, Z=6, R=0.0240. The TG-DTA curves of KLnN(Ln=La,Ce, Pr, Nd, Sm) demonstrate that the processes of dehydration, melt, irreversible phase transition and decomposition of NO3- take place in sequence with the temperature increasing(except KCN). There are three steps in the decomposition of NO3- in KLnN(Ln=La, Nd, Sm) while two steps in KLnN (Ln=Ce, Pr). K(2)Ln(NO3)(5). 2H(2)O are formed at about 225 degrees C by the reaction of the starting materials of KNO3 and Ln(NO3)(3). nH(2)O.
Resumo:
RBa2Cu3O7 (R = Pr, Sm, Eu, Gd, Dy, Y, Ho, Er, Tm) has been studied using complex chemical bond theory. The results indicated that with the decreasing of R radius, the ionicities for all considered types of bond decrease. This is in good agreement with the experimental fact that T-c decreases with the decreasing of R radius. PrBa2Cu3O7 with no Ba-site Pr in this calculation is also predicted to be a superconductor. This supports the conclusion obtained by Blackstead et al. The ionicity for each bond obeys the following order: Ba-O > R-O > Cu(2)-O(1) > Cu(2)-O(2,3) > Cu(1)-O(4) similar to Cu(1)-O(1).
Resumo:
本文生长出了K2Ln(NO3)5.2H2O(Ln=La;Ce;Pr;Nd;Sm)的单晶,并对其进行了晶体结构及差热-热重分析研究.结果表明,K2Ln(NO3)5.2H2O(Ln=La;Ce;Pr;Nd)的晶体属正交晶系,Fdd2空间群.首次生长出KPrN单晶并用直接法解出其晶体结构.解得KPrN的晶胞参数为:a=11.2210(10),b=21.411(3),c=12.208(2),Z=6;R=0.0240.对KLnN加热,则依次出现脱水、熔化、不可逆相变和NO的分解过程(K2Ce(NO3)5·2H2O除外)K2Ln(NO3)5·2H2O(Ln=La;Nd;Sm)的NO分三步分解,K2Ln(NO3)5·2H。O(Ln=Ce;Pr)的NO分两步分解·KNO3和Ln(NO3)3·nH2O的混合物在225℃左右生成K2Ln(NO3)5
Resumo:
Methyl methacrylate (MMA) was polymerized with the rare earth coordination catalyst-system of Nd(O - i-Pr)(3) in toluene. The influences of various ligands in neodymium complexes, molar ratio of Al/Nd, catalyst concentration, catalyst aging time, solvents, the third component CCl4, temperature and time on the polymerization of MMA were studied. The results showed that the polymerization conversion reached more than 80% at a catalyst concentration of 9.2 x 10(-3) mol/L. The appropriate molar ratio of CCl4/Nd was 4. Hydrocarbon was preferred for the polymerzation to obtain a high conversion and a high <(M)over bar w> of PMMA. The H-1 NMR spectra of PMMA indicated that the lower the temperature, the higher the syndiotactic content of PMMA was obtained.