The anodic dissolution of magnesium in chloride and sulphate solutions

The electrochemical behaviour of magnesium was studied in representative chloride and sulphate solutions including NaCl, Na2SO4, NaOH and their mixed solutions, HCl, and H2SO4: (1) by measuring electrochemical polarisation curves, (2) by using electrochemical impedance spectroscopy (EIS), and (3) by simultaneous measurement of hydrogen gas evolution and measurement of magnesium dissolution rates using inductively coupled plasma atomic emission spectrophotometry (ICPEAS). These experiments showed that a partially protective surface film played an important role in the dissolution of magnesium in chloride and sulphate solutions. Furthermore, the experimental data were consistent with the involvement of the intermediate species Mg+ in magnesium dissolution at film imperfections or on a film-free surface. At such sites, magnesium first oxidised electrochemically to the intermediate species Mg+, and then the intermediate species chemically reacted with water to produce hydrogen and Mg2+. The presence of Cl- ions increased the film free area, and accelerated the electrochemical reaction rate from magnesium metal to Mg+. (C) 1997 Elsevier Science Ltd.

Adverse effects of cannabis

Cannabis is the most widely used illicit drug in many developed societies. Its health and psychological effects are not well understood and remain the subject of much debate, with opinions on its risks polarised along the lines of proponents' views on what its legal status should be. An unfortunate consequence of this polarisation of opinion has been the absence of any consensus on what health information the medical profession should give to patients who are users or potential users of cannabis. There is conflicting evidence about many of the effects of cannabis use, so we summarise the evidence on the most probable adverse health and psychological consequences of acute and chronic use. This uncertainty, however, should not prevent medical practitioners from advising patients about the most likely ill-effects of their cannabis use. Here we make some suggestions about the advice doctors can give to patients who use, or are contemplating the use, of this drug.

Influence of microstructure on the corrosion of diecast AZ91D

The corrosion of die cast AZ91D was studied and related to its microstructure. For comparison and to more fully understand the behaviour of die cast AZ91D, corrosion studies and microstructural examinations were also carried out using slowly solidified high purity AZ91, Mg-2%Al, Mg-9%Al, low purity magnesium and high purity magnesium. Corrosion was studied in 1N NaCl at pH 11 by (1) observing the corrosion morphology, (2) measuring electrochemical polarisation curves and (3) simultaneously measuring both the hydrogen evolution rate and the magnesium dissolution rate. The skin of die cast AZ91D showed better corrosion resistance than the interior. This is attributed to a combination of(1) a higher volume fraction of the beta phase, (2) a more continuous beta phase distribution around finer alpha grains, and (3) lower porosity in the skin layer than in the interior of the die casting. This study showed that the casting method can influence the corrosion performance by its influence on the alloy microstructure. (C) 1999 Elsevier Science Ltd. All rights reserved.

The electrochemical corrosion of pure magnesium in 1 N NaCl

An electrochemical investigation was carried out to study the corrosion of pure magnesium in 1 N NaCl at different pH values involving electrochemical polarisation, scanning tunnel microscopy (STM), measurement of hydrogen gas evolution and measurement of the elements dissolved from the magnesium specimen which were determined by inductively coupled plasma atomic emission spectrophotometry (ICPAES). A partially protective surface film was a principal factor controlling corrosion. Film coverage decreased with increasing applied electrode potential. Application of a suitable external cathodic current density was shown to inhibit magnesium dissolution whilst at the same time the hydrogen evolution rate was relatively small. This showed that cathodic protection could be used to significantly reduce magnesium corrosion. A new definition is proposed for the negative difference effect (NDE). (C) 1997 Elsevier Science Ltd.

Developing human minor salivary glands: morphological parallel relation between the expression of TGF-beta isoforms and cytoskeletal markers of glandular maturation

Morphogenesis of salivary glands involves complex coordinated events. Synchronisation between cell proliferation, polarisation and differentiation, which are dependent on epithelial-mesenchymal interactions and on the microenvironment, is a requirement. Growth factors mediate many of these orchestrated biological processes and transforming growth factor-beta (TGF-beta) appear to be relevant. Using immunohistochemistry and immunofluorescence, we have mapped the distribution of TGF-beta 1, 2 and 3 and compared it with the expression of maturation markers in human salivary glands obtained from foetuses ranging from weeks 4 to 24 of gestation. TGF-beta 1 first appeared during canalisation stage in the surrounding mesenchyme and, in the more differentiated stages, was expressed in the cytoplasm of acinar cells throughout the adult gland. TGF-beta 2 was detected since the bud stage of the salivary gland. Its expression was observed in ductal cells and increased along gland differentiation, TGF-beta 3 was detected from the canalisation stage of the salivary gland, being weakly expressed on ductal cells, and it was the only factor detected on myoepithelial cells. The data suggest that TGF-beta have a role to play in salivary gland development and differentiation.

Quantum dynamics of spin polarized optoelectronic processes

We study the quantum dynamics of the emission of multimodal polarized light in light emitting devices (LED) due to spin polarized carriers injection. We present the equations for photon number and carrier numbers, and calculate the polarisation degree of the light generated by LED. (C) 2002 Elsevier Science B.V. All rights reserved.

Hydrofluoric acid pre-treatment for improving 13C CPMAS NMR spectral quality of forest soils in south-east Queensland, Australia

Hydrofluoric acid (HF) was used to pre-treat forest soils of south-east Queensland for assessing the effectiveness of iron (Fe) removal, carbon (C) composition using C-13 cross-polarisation (CP) with magic-angle-spinning (MAS) nuclear magnetic resonance (NMR) before and after the HF pre-treatment, and the improvement of C-13 CPMAS NMR spectra. Soil samples were collected from 4 experimental sites of different soil types, harvest residue management or prescribed burning, and tree species. More than 86% of Fe was in all soil types removed by the HF treatment. The C-13 NMR spectral quality was improved with increased resolution, especially in the alkyl C and O-alkyl C regions, and reduced NMR run-time (1-5 h per sample compared with >20 h per sample without the pre-treatment). The C composition appeared to alter slightly after the pre-treatment, but this might be largely due to improved spectrometer conditions and increased resolution leading to more accurate NMR spectral integration. Organic C recovery after HF pre-treatment varied with soil types and forest management, and soluble soil organic matter (SOM) could be lost during the pre-treatment. The Fourier Transform-Infrared (FT-IR) spectra of HF extracts indicated the preferential removal of carboxylic C groups during the pre-treatment, but this could also be due to adsorbed water on the mineral matter. The NMR spectra revealed some changes in C composition and quality due to residue management and decomposition. Overall, the HF treatment was a useful pre-treatment for obtaining semi-quantitative C-13 CPMAS NMR spectra of subtropical Australian forest soils.

Composition and quality of harvest residues and soil organic matter under windrow residue management in young hoop pine plantations as revealed by solid-state C-13 NMR spectroscopy

Solid-state C-13 nuclear magnetic resonance (NMR) with cross-polarisation (CP) and magic-angle-spinning (MAS) was used to: (a) examine the changes in carbon (C) composition of windrowed harvest residues during the first 3 years of hoop pine plantations in subtropical Australia; (b) assess the impacts of windrowed harvest residues on soil organic matter (SOM) composition and quality in the 0-10 cm soil layer. Harvest residues were collected from 0-, 1-, 2- and 3-year-old windrows of ca. 2.5 m width (15 m apart for 0-, 1- and 2-year-old sites and 10 m apart for 3-year-old site). Soils from the 0 to 10 cm soil layer were collected from the 1-, 2- and 3-year-old sites. The 13C NMR spectra of the harvest residues indicated the presence of lignin in the hoop pine wood, foliage and newly incorporated organic matter (NIOM). Condensed tannin structures were found in the decay-resistant bark, small wood and foliage, but were absent in other residue components and SOM. The NMR spectra of small wood samples contained condensed tannin structures because the outer layer of bark was not removed. NIOM showed a shift from foliage-like structures (celluloses) to lignin-type structures, indicating an incorporation of woody residues from the decomposing harvest residues. Suberins were also present in the small wood, foliage and bark. The 13C CP NMR spectra of SOM indicated that in areas where windrows were present, SOM did not show compositional changes. However, an increase in SOM quality under the windrows in the second year after their formation as characterised by the alkyl C/O-alkyl C (A/O-A) ratio was mainly due to inputs from the decomposition of the labile, readily available components of the windrowed harvest residues. (C) 2002 Published by Elsevier Science B.V.

How does residue management impact soil organic matter composition and quality under Eucalyptus globulus plantations in southwestern Australia?

This study investigated the influence of harvest residue management practices on soil organic matter (SOM) composition and quality from two second-rotation Eucalyptus globulus plantations in southwestern Australia, using solid-state 13C nuclear magnetic resonance (NMR) spectroscopy with cross-polarisation and magic-angle-spinning (CPMAS). Soil samples (0–5 cm) were collected every 12 months for 5 years from two sites that had contrasting soil types and fertility. Harvest residue management treatments established at both sites were (a) no harvest residues; and (b) double harvest residues. The use of 13C CPMAS and DD NMR spectroscopy enabled the successful non-destructive detection of SOM quality changes in the two E. globulus plantations. Relative intensities of 13C CPMAS NMR spectral regions were similar at both sites, and for both harvest residue treatments, indicating that SOM composition was also similar. Dipolar dephasing (DD) NMR spectra revealed resonances in SOM assigned to lignin and tannin structures, with larger resonances in the carbonyl and alkyl C regions that were indicative of cuticular material, enabling detection of changes in SOM quality. Retention of double harvest residues on the soil surface increased the soil quality compared with removal of all harvest residues at both sites as indicated by the NMR aromaticities, but this was most noticeable at Manjimup, which had greater initial soil fertility.

Anti-Corrosion performance of a new silane coating for corrosion protection of AZ31 Magnesium alloy in Hank’s solution

Mg alloys can be used as bioresorsable metallic implants. However, the high corrosion rate of magnesium alloys has limited their biomedical applications. Although Mg ions are essential to the human body, an excess may cause undesirable health effects. Therefore, surface treatments are required to enhance the corrosion resistance of magnesium parts, decreasing its rate to biocompatible levels and allowing its safe application as bioresorbable metallic implants. The application of biocompatible silane coatings is envisaged as a suitable strategy for retarding the corrosion process of magnesium alloys. In the current work, a new glycidoxypropyltrimethoxysilane (GPTMS) based coating was tested on AZ31 magnesium substrates subjected to different surface conditioning procedures before coating deposition. The surface conditioning included a short etching with hydrofluoric acid (HF) or a dc polarisation in alkaline electrolyte. The silane coated samples were immersed in Hank's solution and the protective performance of the coating was studied through electrochemical impedance spectroscopy (EIS). The EIS data was treated by new equivalent circuit models and the results revealed that the surface conditioning process plays a key role in the effectiveness of the silane coating. The HF treated samples led to the highest impedance values and delayed the coating degradation, compared to the mechanically polished samples or to those submitted to dc polarisation.

Development of polymeric membranes for forward osmosis

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Química e Bioquímica

Hydrogen evolution on nanostructured Ni-Cu foams

Three-dimensional (3D) nickel-copper (Ni-Cu) nanostructured foams were prepared by galvanostatic electrodeposition, on stainless steel substrates, using the dynamic hydrogen bubble template. These foams were tested as electrodes for the hydrogen evolution reaction (HER) in 8 M KOH solutions. Polarisation curves were obtained for the Ni-Cu foams and for a solid Ni electrode, in the 25-85 degrees C temperature range, and the main kinetic parameters were determined. It was observed that the 3D foams have higher catalytic activity than pure Ni. HER activation energies for the Ni-Cu foams were lower (34-36 kJ mol(-1)) than those calculated for the Ni electrode (62 kJ mol(-1)). The foams also presented high stability for HER, which makes them potentially attractive cathode materials for application in industrial alkaline electrolysers.

Graphene-based nanostructures: Plasmonics in the THz range

The properties of surface plasmon-polaritons (SPPs) in graphene are discussed and several possible ways of coupling electromagnetic radiation in the terahertz (THz) spectral range to this type of surface waves are described: (i) the attenuated total reflection (ATR) method employing a prism, (ii) graphene-based gratings or graphene monolayers with modulated conductivity, (iii) a metal stripe on top of the graphene layer, and (iv) a nanoparticle located above it. Potentially interesting for applications SPP effects, such as switching, modulation and polarization of THz radiation, as well as its enhanced absorption in graphene, are considered. The discussion also concerns the impact of the nonlinear properties of graphene, such as optical bistability.

Income stratification and the measurement of interdistributional inequality between multiple groups

This paper proposes a new class of stratification indices that measure interdistributional inequality between multiple groups. The class is based on a conceptualisation of stratification as a process that results in a hierarchical ordering of groups and therefore seeks to capture not only the extent to which groups form well-defined strata in the income distribution but also the scale of the resultant differences in income standards between them, where these two factors play the same role as identification and alienation respectively in the measurement of polarisation. The properties of the class as a whole are investigated as well as those of selected members of it: zeroth and first power indices may be interpreted as measuring the overall incidence and depth of stratification respectively, while higher power indices members are directly sensitive to the severity of stratification between groups. An illustrative application provides an empirical analysis of global income stratification by regions in 1993.

Faire la ville juste : une analyse "in itinere" de la maîtrise publique d'ouvrage du projet urbain Carré de Soie (métropole lyonnaise)

Dans certaines portions des agglomérations (poches de pauvreté de centre-ville, couronnes suburbaines dégradées, espaces périurbains sans aménité), un cumul entre des inégalités sociales (pauvreté, chômage, etc.) et environnementales (exposition au bruit, aux risques industriels, etc.) peut être observé. La persistance de ces inégalités croisées dans le temps indique une tendance de fond : la capacité d'accéder à un cadre de vie de qualité n'est pas équitablement partagée parmi les individus. Ce constat interroge : comment se créent ces inégalités ? Comment infléchir cette tendance et faire la ville plus juste ?¦Apporter des réponses à cette problématique nécessite d'identifier les facteurs de causalités qui entrent en jeu dans le système de (re)production des inégalités urbaines. Le fonctionnement des marchés foncier et immobilier, la « tyrannie des petites décisions » et les politiques publiques à incidence spatiale sont principalement impliqués. Ces dernières, agissant sur tous les éléments du système, sont placées au coeur de ce travail. On va ainsi s'intéresser précisément à la manière dont les collectivités publiques pilotent la production de la ville contemporaine, en portant l'attention sur la maîtrise publique d'ouvrage (MPO) des grands projets urbains.¦Poser la question de la justice dans la fabrique de la ville implique également de questionner les référentiels normatifs de l'action publique : à quelle conception de la justice celle-ci doit- elle obéir? Quatre perspectives (radicale, substantialiste, procédurale et intégrative) sont caractérisées, chacune se traduisant par des principes d'action différenciés. Une méthodologie hybride - empruntant à la sociologie des organisations et à l'analyse des politiques publiques - vient clore le volet théorique, proposant par un détour métaphorique d'appréhender le projet urbain comme une pièce de théâtre dont le déroulement dépend du jeu d'acteurs.¦Cette méthodologie est utilisée dans le volet empirique de la recherche, qui consiste en une analyse de la MPO d'un projet urbain en cours dans la première couronne de l'agglomération lyonnaise : le Carré de Soie. Trois grands objectifs sont poursuivis : descriptif (reconstruire le scénario), analytique (évaluer la nature de la pièce : conte de fée, tragédie ou match d'improvisation ?) et prescriptif (tirer la morale de l'histoire). La description de la MPO montre le déploiement successif de quatre stratégies de pilotage, dont les implications sur les temporalités, le contenu du projet (programmes, morphologies) et les financements publics vont être déterminantes. Sur la base de l'analyse, plusieurs recommandations peuvent être formulées - importance de l'anticipation et de l'articulation entre planification et stratégie foncière notamment - pour permettre à la sphère publique de dominer le jeu et d'assurer la production de justice par le projet urbain (réalisation puis entretien des équipements et espaces publics, financement de logements de qualité à destination d'un large éventail de populations, etc.). Plus généralement, un décalage problématique peut être souligné entre les territoires stratégiques pour le développement de l'agglomération et les capacités de portage limitées des communes concernées. Ce déficit plaide pour le renforcement des capacités d'investissement de la structure intercommunale.¦La seule logique du marché (foncier, immobilier) mène à la polarisation sociale et à la production d'inégalités urbaines. Faire la ville juste nécessite une forte volonté des collectivités publiques, laquelle doit se traduire aussi bien dans l'ambition affichée - une juste hiérarchisation des priorités dans le développement urbain - que dans son opérationnalisation - une juste maîtrise publique d'ouvrage des projets urbains.¦Inner-city neighborhoods, poor outskirts, and peri-urban spaces with no amenities usually suffer from social and environmental inequalities, such as poverty, unemployment, and exposure to noise and industrial hazards. The observed persistence of these inequalities over time points to an underlying trend - namely, that access to proper living conditions is fundamentally unequal, thus eliciting the question of how such inequalities are effected and how this trend can be reversed so as to build a more equitable city.¦Providing answers to such questions requires that the causal factors at play within the system of (re)production of urban inequalities be identified. Real estate markets, "micromotives and macrobehavior", and public policies that bear on space are mostly involved. The latter are central in that they act on all the elements of the system. This thesis therefore focuses on the way public authorities shape the production of contemporary cities, by studying the public project ownership of major urban projects.¦The study of justice within the urban fabric also implies that the normative frames of reference of public action be questioned: what conception of justice should public action refer to? This thesis examines four perspectives (radical, substantialist, procedural, and integrative) each of which results in different principles of action. This theoretical part is concluded by a hybrid methodology that draws from sociology of organizations and public policy analysis and that suggests that the urban project may be understood as a play, whose outcome hinges on the actors' acting.¦This methodology is applied to the empirical analysis of the public project ownership of an ongoing urban project in the Lyon first-ring suburbs: the Carré de Soie. Three main objectives are pursued: descriptive (reconstructing the scenario), analytical (assessing the nature of the play - fairy tale, tragedy or improvisation match), and prescriptive (drawing the moral of the story). The description of the public project ownership shows the successive deployment of four control strategies, whose implications on deadlines, project content (programs, morphologies), and public funding are significant. Building on the analysis, several recommendations can be made to allow the public sphere to control the process and ensure the urban project produces equity (most notably, anticipation and articulation of planning and real- estate strategy, as well as provision and maintenance of equipment and public spaces, funding of quality housing for a wide range of populations, etc.). More generally, a gap can be highlighted between those territories that are strategic to the development of the agglomeration and the limited resources of the municipalities involved. This deficit calls for strengthening the investment abilities of the intermunicipal structure.¦By itself, the real-estate market logic brings about social polarization and urban inequalities. Building an equitable city requires a strong will on the part of public authorities, a will that must be reflected both in the stated ambition - setting priorities of urban development equitably - and in its implementation managing urban public projects fairly.