Analysis of Two-Speed Wind Farm Operation From Grid-Side Measurements

This paper analyzes data captured by a phasor measurement unit at a wind farm, employing two-speed induction generators, and investigates aspects of the control system's interaction with the power system. Composite superimposed transient events are proposed as a method to improve the quality of the analysis and reduce errors caused by unknowns, such as wind speed variation. A Mathworks SimPowerSystems model validates the inertia contribution of the wind farm, which is an important parameter in power systems with high wind penetration. Transients caused by turbine speed transitions are identified and explained. The analysis also highlights areas where wind farm control should be improved if useful inertia contribution is to be provided.

A statistical process control approach for automatic anti-islanding detection using synchrophasors

Anti-islanding protection is becoming increasingly important due to the rapid installation of distributed generation from renewable resources like wind, tidal and wave, solar PV, bio-fuels, as well as from other resources like diesel. Unintentional islanding presents a potential risk for damaging utility plants and equipment connected from the demand side, as well as to public and personnel in utility plants. This paper investigates automatic islanding detection. This is achieved by deploying a statistical process control approach for fault detection with the real-time data acquired through a wide area measurement system, which is based on Phasor Measurement Unit (PMU) technology. In particular, the principal component analysis (PCA) is used to project the data into principal component subspace and residual space, and two statistics are used to detect the occurrence of fault. Then a fault reconstruction method is used to identify the fault and its development over time. The proposed scheme has been used in a real system and the results have confirmed that the proposed method can correctly identify the fault and islanding site.

Inter-Area Power Oscillation Frequency Mode with Wind Turbine Generator in Irish Power System using PMU Data

Two case studies are presented in this paper to demonstrate the impact of different power system operation conditions on the power oscillation frequency modes in the Irish power system. A simplified 2 area equivalent of the Irish power system has been used in this paper, where area 1 represents the Republic of Ireland power system and area 2 represents the Northern Ireland power system.

The potential power oscillation frequency modes on the interconnector during different operation conditions have been analysed in this paper. The main objective of this paper is to analyse the influence of different operation conditions involving wind turbine generator (WTG) penetration on power oscillation frequency modes using phasor measurement unit (PMU) data.

Fast Fourier transform (FFT) analysis was performed to identify the frequency oscillation mode while correlation coefficient analysis was used to determine the source of the frequency oscillation. The results show that WTG, particularly fixed speed induction generation (FSIG), gives significant contribution to inter-area power oscillation frequency modes during high WTG operation.

Securing the smart grid

The availability of electricity is fundamental to modern society. It is at the top of the list of critical infrastructures and its interruption can have severe consequences. This highly important system is now evolving to become more reliable, efficient, and clean. This evolving infrastructure has become known as the smart grid; and these future smart grid systems will rely heavily on ICT. This infrastructure will require many servers and due to the nature of the grid, many of these systems will be geographically diverse requiring communication links. At the heart of this ICT infrastructure will be security. At each level of the smart grid from smart metering right through to remote sensing and control networks, security will be a key factor for system design consideration. With an increased number of ICT systems in place the security risk also increases. In this paper the authors discuss the changing nature of security in relation to the smart grid by looking at the move from legacy systems to more modern smart grid systems. The potential planes of attack for future smart grid systems are identified, and the general anatomy of a cyber-attack is presented. The authors then introduce the various threat levels of different types of attack and the mitigation techniques that could be put in place for each. Finally, the authors' introduce a Phasor Measurement Unit (PMU) communication system (operated by the authors) that can be used as a test-bed for some of the proposed future security research.

Identification of Small Signal Oscillation Mode Parameters from Simulated and Actual PMU Ringdown Data

This paper presents the practical use of Prony Analysis to identify small signal oscillation mode parameters from simulated and actual phasor measurement unit (PMU) ringdown data. A well-known two-area four-machine power system was considered as a study case while the latest PMU ringdown data were collected from a double circuit 275 kV main interconnector on the Irish power system. The eigenvalue analysis and power spectral density were also conducted for the purpose of comparison. The capability of Prony Analysis to identify the mode parameters from three different types of simulated PMU ringdown data has been shown successfully. Furthermore, the results indicate that the Irish power system has dominant frequency modes at different frequencies. However, each mode has good system damping.

Indices for the identification of biologically productive cashmere goats within farms

Objectively comparing cashmere goats with different cashmere production, mean fibre diameter (MFD) and staple length (SL) is difficult for farmers. We aimed to develop indices to enable cashmere producers to identify productive goats within their own farms once adjustments had been made for the primary determinants of cashmere production. That is we aimed to develop indices that identify goats and herds that biologically have a high fleece weight in relation to MFD and SL. We used a sample of 1244 commercial cashmere fleeces from goats originating from many Australian farms based in different environmental zones and a previously developed general linear model that related the logarithm of clean cashmere production (CCMwt) and any other potential determinant. In the present study, sub-models were investigated in order to develop new indices for comparing goats in the same farm, based on fleece characteristics and biological efficiency. New Index (MFD), equal to 6.02×CCMwt/1.1531^MFD, was developed to identify animals of biologically high CCMwt in relation to their MFD. Unlike previously reported results that MFD is not a useful measurement for comparing the biological efficiency of cashmere goats across farms, the New Index (MFD) allows comparison of the biological efficiency of cashmere goats within farms. New Index (SL), equal to 2.70 × CCMwt/1.1414^SL, was developed to identify animals of biologically high CCMwt in relation to their SL. New Index (SL) is very similar to the Clean Cashmere Staple Length Index (CCSLI) that had been previously reported for comparison of cashmere goats across farms, and thus the CCSLI can be usefully used for comparing the biological efficiency of cashmere goats both across and within farms. New Index MFD, SL = 8.90 × CCMwt/1.243^(MFD+SL)/2 was developed to identify animals of biologically high CCMwt in relation to both their MFD and SL within farms, and provides useful information above using either New Index (MFD) or CCSLI. The indices can be presented in the same measurement units as fleece weight, which is a biological concept easily understood by cashmere producers, and enable comparisons to be made between animals using just one attribute, clean cashmere weight.

Estudo sobre as unidades de medidas das grandezas físicas básicas: comprimento, massa e tempo

Measurement units are used almost automatically nowadays, but few people know the origin of the units of length (meter), mass (kilogram) and time (second). And do not care to know what were anciently units of which our ancestors used, the difficulties that existed to make a set of measures. The aim of this work is to make a historical approach, through various units of measure. They are old, unusual to others that have been forgotten since the standardization of meters, and is also discussed about the metric system Englih (Once and foot), AV system (eg pound grain) that are still used in some countries like United States and England, the Troy system consisting of units of measure for precious stones and metals (eg gold and diamond) are also cited some physical concepts as reference: inertial, non-inertial; mass: gravity, relativistic, inertial

Biomechanics of sprint running: a methodological contribution

Sports biomechanics describes human movement from a performance enhancement and an injury reduction perspective. In this respect, the purpose of sports scientists is to support coaches and physicians with reliable information about athletes’ technique. The lack of methods allowing for in-field athlete evaluation as well as for accurate joint force estimates represents, to date, the main limitation to this purpose. The investigations illustrated in the present thesis aimed at providing a contribution towards the development of the above mentioned methods. Two complementary approaches were adopted: a Low Resolution Approach – related to performance assessment – where the use of wearable inertial measurement units is exploited during different phases of sprint running, and a High Resolution Approach – related to joint kinetics estimate for injury prevention – where subject-specific, non-rigid constraints for knee joint kinematic modelling used in multi-body optimization techniques are defined. Results obtained using the Low Resolution Approach indicated that, due to their portability and inexpensiveness, inertial measurement systems are a valid alternative to laboratory-based instrumentation for in-field performance evaluation of sprint running. Using acceleration and angular velocity data, the following quantities were estimated: trunk inclination and angular velocity, instantaneous horizontal velocity and displacement of a point approximating the centre of mass, and stride and support phase durations. As concerns the High Resolution Approach, results indicated that the length of the anterior cruciate and lateral collateral ligaments decreased, while that of the deep bundle of the medial collateral ligament increased significantly during flexion. Variations of the posterior cruciate and the superficial bundle of the medial collateral ligament lengths were concealed by the experimental indeterminacy. A mathematical model was provided that allowed the estimate of subject-specific ligament lengths as a function of knee flexion and that can be integrated in a multi-body optimization procedure.

Assessment of Daily Life Mobility Levels using Wearable Inertial Sensors and Minimun Measured Input Models

Tracking activities during daily life and assessing movement parameters is essential for complementing the information gathered in confined environments such as clinical and physical activity laboratories for the assessment of mobility. Inertial measurement units (IMUs) are used as to monitor the motion of human movement for prolonged periods of time and without space limitations. The focus in this study was to provide a robust, low-cost and an unobtrusive solution for evaluating human motion using a single IMU. First part of the study focused on monitoring and classification of the daily life activities. A simple method that analyses the variations in signal was developed to distinguish two types of activity intervals: active and inactive. Neural classifier was used to classify active intervals; the angle with respect to gravity was used to classify inactive intervals. Second part of the study focused on extraction of gait parameters using a single inertial measurement unit (IMU) attached to the pelvis. Two complementary methods were proposed for gait parameters estimation. First method was a wavelet based method developed for the estimation of gait events. Second method was developed for estimating step and stride length during level walking using the estimations of the previous method. A special integration algorithm was extended to operate on each gait cycle using a specially designed Kalman filter. The developed methods were also applied on various scenarios. Activity monitoring method was used in a PRIN’07 project to assess the mobility levels of individuals living in a urban area. The same method was applied on volleyball players to analyze the fitness levels of them by monitoring their daily life activities. The methods proposed in these studies provided a simple, unobtrusive and low-cost solution for monitoring and assessing activities outside of controlled environments.

Modelling and analysis of networked control strategies in smart power distribution grids: development of co-simulation tools

This thesis is focused on Smart Grid applications in medium voltage distribution networks. For the development of new applications it appears useful the availability of simulation tools able to model dynamic behavior of both the power system and the communication network. Such a co-simulation environment would allow the assessment of the feasibility of using a given network technology to support communication-based Smart Grid control schemes on an existing segment of the electrical grid and to determine the range of control schemes that different communications technologies can support. For this reason, is presented a co-simulation platform that has been built by linking the Electromagnetic Transients Program Simulator (EMTP v3.0) with a Telecommunication Network Simulator (OPNET-Riverbed v18.0). The simulator is used to design and analyze a coordinate use of Distributed Energy Resources (DERs) for the voltage/var control (VVC) in distribution network. This thesis is focused control structure based on the use of phase measurement units (PMUs). In order to limit the required reinforcements of the communication infrastructures currently adopted by Distribution Network Operators (DNOs), the study is focused on leader-less MAS schemes that do not assign special coordinating rules to specific agents. Leader-less MAS are expected to produce more uniform communication traffic than centralized approaches that include a moderator agent. Moreover, leader-less MAS are expected to be less affected by limitations and constraint of some communication links. The developed co-simulator has allowed the definition of specific countermeasures against the limitations of the communication network, with particular reference to the latency and loss and information, for both the case of wired and wireless communication networks. Moreover, the co-simulation platform has bee also coupled with a mobility simulator in order to study specific countermeasures against the negative effects on the medium voltage/current distribution network caused by the concurrent connection of electric vehicles.

Assessment of gait spatio-temporal parameters in neurological disorders using wearable inertial sensors

Movement analysis carried out in laboratory settings is a powerful, but costly solution since it requires dedicated instrumentation, space and personnel. Recently, new technologies such as the magnetic and inertial measurement units (MIMU) are becoming widely accepted as tools for the assessment of human motion in clinical and research settings. They are relatively easy-to-use and potentially suitable for estimating gait kinematic features, including spatio-temporal parameters. The objective of this thesis regards the development and testing in clinical contexts of robust MIMUs based methods for assessing gait spatio-temporal parameters applicable across a number of different pathological gait patterns. First, considering the need of a solution the least obtrusive as possible, the validity of the single unit based approach was explored. A comparative evaluation of the performance of various methods reported in the literature for estimating gait temporal parameters using a single unit attached to the trunk first in normal gait and then in different pathological gait conditions was performed. Then, the second part of the research headed towards the development of new methods for estimating gait spatio-temporal parameters using shank worn MIMUs on different pathological subjects groups. In addition to the conventional gait parameters, new methods for estimating the changes of the direction of progression were explored. Finally, a new hardware solution and relevant methodology for estimating inter-feet distance during walking was proposed. Results of the technical validation of the proposed methods at different walking speeds and along different paths against a gold standard were reported and showed that the use of two MIMUs attached to the lower limbs associated with a robust method guarantee a much higher accuracy in determining gait spatio-temporal parameters. In conclusion, the proposed methods could be reliably applied to various abnormal gaits obtaining in some cases a comparable level of accuracy with respect to normal gait.

Analisi del cammino in acqua tramite sensori inerziali: Accuratezza strumentale e fasce di normalita

La biocinematica è una branca della biomeccanica che studia il movimento dei segmenti corporei senza considerare le cause che lo determinano. Le grandezze fisiche di interesse (posizione, velocità ed accelerazione) vengono determinate grazie ai sistemi di analisi del movimento che sfruttano principi fisici di funzionamento differenti con vari gradi di invasività. Lo sviluppo di nuove tecnologie di costruzione dei sensori inerziali, ha fornito una valida alternativa alle tecniche classiche per l’analisi del movimento umano. Gli IMUs (Inertial Measurement Units) sono facilmente indossabili, possono essere facilmente utilizzati fuori dal laboratorio, hanno un costo molto inferiore rispetto a quello dei sistemi opto-elettronici, non richiedono particolari abilità per essere utilizzati dall’utente e si configurano facilmente. In questa tesi verrà analizzato il cammino e costruite le bande di normalità sia in laboratorio che in acqua tramite i sensori inerziali. L’utilizzo in acqua delle tecniche classiche di analisi del movimento presenta dei problemi di accuratezza (legati ad esempio alla presenza delle bolle d’aria in acqua) che impediscono di effettuare un confronto tra i risultati ottenuti dai sensori e quelli ottenuti con un gold standard. Per questo motivo, è stato implementato un test per valutare l’accuratezza dei sensori e l’influenza dei disturbi magnetici sui magnetometri nelle stesse condizioni ambientali in cui si desidera registrare il cammino. Quest’analisi strumentale ha consentito anche di individuare, tra i diversi algoritmi di fusione utilizzati (algoritmo di fabbrica e algoritmo di Madgwick), quello da impiegare nell’analisi del suddetto task motorio per stimare in maniera più accurata l’orientamento dei sensori in acqua e in laboratorio. L'algoritmo di fabbrica viene escluso dal processo di sensor fusion poiché mostra un'accuratezza peggiore rispetto all'algoritmo di Madgwick. Dal momento che il protocollo implementato di analisi del cammino attraverso i sensori inerziali è già stato validato a secco e che le prestazioni dei sensori sono analoghe a secco e in acqua, il protocollo può essere utilizzato per la stima della cinematica degli arti inferiori nell'acqua. Le differenze riscontrate tra le curve del cammino sono da imputare sia alla diversa condizione ambientale che alla minore velocità di progressione che i soggetti manifestano in acqua. Infatti, la velocità media di progressione è 151.1 cm/s in laboratorio e 40.7 cm/s in acqua.

Automatic Food Intake Assessment Using Camera Phones

Obesity is becoming an epidemic phenomenon in most developed countries. The fundamental cause of obesity and overweight is an energy imbalance between calories consumed and calories expended. It is essential to monitor everyday food intake for obesity prevention and management. Existing dietary assessment methods usually require manually recording and recall of food types and portions. Accuracy of the results largely relies on many uncertain factors such as user's memory, food knowledge, and portion estimations. As a result, the accuracy is often compromised. Accurate and convenient dietary assessment methods are still blank and needed in both population and research societies. In this thesis, an automatic food intake assessment method using cameras, inertial measurement units (IMUs) on smart phones was developed to help people foster a healthy life style. With this method, users use their smart phones before and after a meal to capture images or videos around the meal. The smart phone will recognize food items and calculate the volume of the food consumed and provide the results to users. The technical objective is to explore the feasibility of image based food recognition and image based volume estimation. This thesis comprises five publications that address four specific goals of this work: (1) to develop a prototype system with existing methods to review the literature methods, find their drawbacks and explore the feasibility to develop novel methods; (2) based on the prototype system, to investigate new food classification methods to improve the recognition accuracy to a field application level; (3) to design indexing methods for large-scale image database to facilitate the development of new food image recognition and retrieval algorithms; (4) to develop novel convenient and accurate food volume estimation methods using only smart phones with cameras and IMUs. A prototype system was implemented to review existing methods. Image feature detector and descriptor were developed and a nearest neighbor classifier were implemented to classify food items. A reedit card marker method was introduced for metric scale 3D reconstruction and volume calculation. To increase recognition accuracy, novel multi-view food recognition algorithms were developed to recognize regular shape food items. To further increase the accuracy and make the algorithm applicable to arbitrary food items, new food features, new classifiers were designed. The efficiency of the algorithm was increased by means of developing novel image indexing method in large-scale image database. Finally, the volume calculation was enhanced through reducing the marker and introducing IMUs. Sensor fusion technique to combine measurements from cameras and IMUs were explored to infer the metric scale of the 3D model as well as reduce noises from these sensors.

OUT-OF-STEP DETECTION BASED ON ZUBOV’S APPROXIMATION BOUNDARY METHOD

Disturbances in power systems may lead to electromagnetic transient oscillations due to mismatch of mechanical input power and electrical output power. Out-of-step conditions in power system are common after the disturbances where the continuous oscillations do not damp out and the system becomes unstable. Existing out-of-step detection methods are system specific as extensive off-line studies are required for setting of relays. Most of the existing algorithms also require network reduction techniques to apply in multi-machine power systems. To overcome these issues, this research applies Phasor Measurement Unit (PMU) data and Zubov’s approximation stability boundary method, which is a modification of Lyapunov’s direct method, to develop a novel out-of-step detection algorithm. The proposed out-of-step detection algorithm is tested in a Single Machine Infinite Bus system, IEEE 3-machine 9-bus, and IEEE 10-machine 39-bus systems. Simulation results show that the proposed algorithm is capable of detecting out-of-step conditions in multi-machine power systems without using network reduction techniques and a comparative study with an existing blinder method demonstrate that the decision times are faster. The simulation case studies also demonstrate that the proposed algorithm does not depend on power system parameters, hence it avoids the need of extensive off-line system studies as needed in other algorithms.

A cost-effective surgical navigation solution for periacetabular osteotomy (PAO) surgery

In this chapter a low-cost surgical navigation solution for periacetabular osteotomy (PAO) surgery is described. Two commercial inertial measurement units (IMU, Xsens Technologies, The Netherlands), are attached to a patient’s pelvis and to the acetabular fragment, respectively. Registration of the patient with a pre-operatively acquired computer model is done by recording the orientation of the patient’s anterior pelvic plane (APP) using one IMU. A custom-designed device is used to record the orientation of the APP in the reference coordinate system of the IMU. After registration, the two sensors are mounted to the patient’s pelvis and acetabular fragment, respectively. Once the initial position is recorded, the orientation is measured and displayed on a computer screen. A patient-specific computer model generated from a pre-operatively acquired computed tomography (CT) scan is used to visualize the updated orientation of the acetabular fragment. Experiments with plastic bones (7 hip joints) performed in an operating room comparing a previously developed optical navigation system with our inertial-based navigation system showed no statistical difference on the measurement of acetabular component reorientation (anteversion and inclination). In six out of seven hip joints the mean absolute difference was below five degrees for both anteversion and inclination.