Modelos para análise e dimensionamento de painéis de alvenaria estrutural

The main objective of this thesis was the study of bracing panels of structural masonry, by applying the Finite Element Method and Strut and Tie Method. It was analyzed the following aspects: the effect of orthotropy on the behavior of the panels; distribution of horizontal forces between panels for buildings; comparison between Equivalent Frame and Finite Elements models; panels design with the Strut and Tie Method. The results showed that one should not disregard the orthotropy, otherwise this can lead to models stiffer than the real. Regarding the distribution of horizontal forces, showed that the disregard of lintels and shear deformation leads to significant differences in the simplified model. The results showed also that the models in Finite Element and Equivalent Frame exhibit similar behavior in respect to stiffness of panels and stress distribution over the sessions requested. It was discussing criteria for designing Strut and Tie Method models in one floor panels. Then, the theoretical strength these panels was compared with the rupture strength of panels tested in the literature. The theoretical maximum strength were always less than the rupture strength of the panels obtained in tests, due to the fact that the proposed model cannot represent the behavior of the masonry after the start of the panel cracking due to plasticization of the reinforcement

Propriedades físicas e mecânicas de painéis LVL de Eucalyptus grandis

This paper mainly aimed to evaluate the physical and mechanical properties of LVL panels made from Eucalyptus grandis, from reforestation at the region of Senges, in Parana state, Brazil. LVL panels were manufactured using 23 veneers (2,4mm thick each one) in commercial dimension of 2.500 mm long and 1,200 mm wide. The properties of static bending were analyzed (strength and rigidity) in beams of the LVL, in the flatwise and edgewise positions. The properties of compression parallel to grain and shear parallel in the plans L-X and L-Y and density in this LVL panels were also analyzed according to ASTM-D 5456/4761 and ASTM-D 198 codes. The mean values to flatwise bending MOE and MOR were 13114 MPa and 88.76 MPa, respectively, and for edgewise bending MOE and MOR were 15871 MPa and 88.63 MPa, respectively. The density (12%) of the LVL panels and of the veneers were 690 kg/m(3) and 649 kg/m(3). The mean values to parallel compression MOE and MOR were 16856 MPa and 58.05 MPa, respectively. The mean values of the maximum resistance to shear parallel in the plans L-X and L-Y were 5.96 MPa and 591 MPa, respectively. All these values reached partially or they passed the medium limits of reference (normative codes, researches and commercial catalogs) established for LVL panels and original solid wood, attesting overall the quality of those panels produced with this wood.

Painéis-sanduíche com núcleo de EPS reciclado: metodologia de execução e determinação de propriedades termofísicas

New materials made from industrial wastes have been studied as an alternative to traditional fabrication processes in building and civil engineering. These materials are produced considering some issues like: cost, efficiency and reduction of nvironmental damage. Specifically in cases of materials destined to dwellings in low latitude regions, like Brazilian Northeast, efficiency is related to mechanical and thermal resistance. Thus, when thermal insulation and energetic efficiency are aimed, it s important to increase thermal resistance without depletion of mechanical properties. This research was conducted on a construction element made of two plates of cement mortar, interspersed with a plate of recycled expanded polystyrene (EPS). This component, widely known as sandwich-panel, is commonly manufactured with commercial EPS whose substitution was proposed in this study. For this purpose it was applied a detailed methodology that defines parameters to a rational batching of the elements that constitute the nucleus. Samples of recycled EPS were made in two different values of apparent specific mass (ρ = 65 kg/m³; ρ = 130 kg/m³) and submitted to the Quick-Line 30TM that is a thermophysical properties analyzer. Based on the results of thermal conductivity, thermal capacity and thermal diffusivity obtained, it was possible to assure that recycled EPS has thermal insulation characteristics that qualify it to replace commercial EPS in building and civil engineering industry

Desgaste corrosivo-cavitativo-erosivo de um aço-carbono em meio aquoso com frações de sal (NaCl), CO2 e particulados sólidos (SiO2)

A batch of eighty-four coupons of low carbon steel were investigated at laboratory conditions under a corrosive, cavitative-corrosive (CO2) and corrosive-erosive (SiO2 + CO2) in an aqueous salt solution and two levels of temperature. The following measurements were made on Vickers (HV0,05, HV0,10, HV0,20) Microhardness tests at three levels of subsurface layer. A turbulent flow collided on the cylindrical sample, with and without mechanical stirring and gas bubbling, with and without fluid contamination by solid particles of SiO2, at two temperatures. Surface Roughness and Waviness, under two conditions "as received, after machining" and "after worn out", as well as gravimetric and electrochemical parameter were measured on the two opposite generatrices of each cylindrical sample, on the flow upstream (0°) and downstream (180°) by Profilometry, Mass Variation and Linear Polarization Resistance (LPR). The results of the Microhardness and Surface Texture of all coupons were subjected to statistical comparison, using the software Statgraphics® Centurion XVI, 95% statistical certainty, and significant differences were observed in some arrays of measurements. The corrosive wear rate measured by LPR and mass variation shown to be sensitive to the presence of bubbles and hydrodynamic fluctuations inside the cell, considering the temperature and contamination of corrosive fluid by solid particles. The main results of visual inspection relative to some topologies of the surface damages involving different mechanisms that were seen to give explanation for some fluctuations in wear rates of the steel experimentally investigated

Avaliação de painéis produzidos a partir de resíduos sólidos para aplicação na arquitetura

O presente trabalho tem por objetivo o reaproveitamento de resíduos sólidos na preparação de painéis para uso na arquitetura. Para atingir as metas propostas, painéis foram preparados a partir de resíduos provenientes de embalagens cartonadas e plásticas, utilizando-se como elemento de reforço, resíduos lignocelulósicos (casca de amendoim e de arroz). A concentração e a natureza dos resíduos utilizados como matriz e como carga foram variadas gerando doze condições experimentais diferentes. As propriedades avaliadas dos painéis foram o módulo de ruptura, módulo de elasticidade, tração perpendicular à superfície, inchamento em espessura, absorção de água e densidade. Todos os ensaios foram realizados segundo as normas ASTM D1037 e EN 317, referente à chapa de partículas. Os resultados foram analisados segundo a norma ANSI A208.1 que especifica as propriedades de desempenho requeridas para as chapas de partículas. Os painéis foram classificados como de baixa densidade, podendo ser utilizados como forros, divisórias, revestimento decorativos e demais aplicações que requerem as mesmas propriedades físicas e mecânicas. Os painéis a base de embalagem plástica reforçados com casca de arroz apresentaram propriedades superiores do que os demais painéis produzidos. O elemento arquitetônico desenvolvido neste estudo representa um novo mercado potencial, podendo ser empregado no ambiente urbano e rural, atendendo ao conceito de produto ecoeficiente.

Influência da Qualidade das Lâminas no Desempenho Mecânico à Flexão de Painéis Compensados de Hevea brasiliensis

After concluding the main phase of commercial exploration of latex (about 30 years ago), rubber wood plantations can be utilized as an alternative source of wood for sawmills and other wood based products with more aggregate value; tendency already confirmed in countries of southeastern Asia. The main purpose of this research was to evaluate the influence of dynamic modulus of elasticity veneers on the mechanical performance in the bending of plywood made from Hevea brasiliensis. For this study, rubber tree veneers were sorted in three classes of dynamic modulus of elasticity: low (from 4887-7323 MPa), medium (from 8200-8948 MPa) and high (from 10979-13010 MPa). Panels were produced according to five treatments with different veneer classes and arrangements. Results showed significant effect of the treatments in the mechanical performance in the bending of panels. Panels with better mechanical performance were produced exclusively with medium and high dynamic modulus of elasticity. Panels made with low modulus of elasticity veneers presented lower mechanical performance even when combined with high modulus of elasticity veneers.

Painéis de partículas de madeira leucena e resina poliuretana derivada de óleo de mamona

This research aimed to test particleboard with leucena (Leucaena leucocephala) wood particles and polyurethane resin castor oil based. The response variables are: modulus of rupture (MOR), internal adhesion (AI), apparent density (dap) and wood moisture content (um). The experiments were developed based on the methodological procedures of the ABNT NBR 14810:2002 standard. The particleboards were manufactured by hot-pressing at 4MPa and 90°C, using timber particles with 5% of moisture content and 10% of monocomponent and bicomponent polyurethane resin. The higher moisture content was achieved when the monocomponent polyurethane resin was used. The bicomponent polyurethane resin provided a percent increase of 43.7% and 22.7% on the modulus of rupture and apparent density, respectively, when compared to the standard limit. The internal adhesion of the panels manufactured with monocomponent resin was 2.45 times higher than the standard limit. The confidence interval between means revealed that the internal adhesion and apparent density exhibited statistical equivalence. A good correlation between the internal adhesion and apparent density was found, for this reason it was possible to estimate the internal adhesion of the panels based on the apparent density data.

Painéis alternativos produzidos a partir de resíduos termoplásticos e da pupunheira (Bactris gasipaes Kunth)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da viabilidade técnica e econômica para aproveitamento de cascas de eucalyptus gerados no processo de fabricação de painéis de madeira

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Aproveitamento de madeiras tropicais para confecção e avaliação de painéis aglomerados com mistura de partículas e resinas alternativas

Pós-graduação em Engenharia Civil - FEIS

Aproveitamento de resíduos de empresas moveleiras da região de São José do Rio Preto para confecção e avaliação de painéis aglomerados

Pós-graduação em Engenharia Civil - FEIS

Estudo da estabilidade e da capacidade resistente de painéis estruturais do sistema construtivo Light Steel Framing

Pós-graduação em Engenharia Civil - FEIS

Desequilíbrio de ligação e associação entre polimorfismos de base única com maciez da carne e espessura de gordura em bovinos Nelore utilizando painéis de alta densidade

Pós-graduação em Genética e Melhoramento Animal - FCAV

Painéis de bambu, uso e aplicações: uma experiência didática nos cursos de design em Bauru, São Paulo

Pós-graduação em Design - FAAC

Projeto, construção de equipamento para obtenção de compósitos de matriz metálica particulados, utilizando o processo de fundição com agitação mecânica

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)