Effect of main-chain rigidity on the phase transitional behavior of comblike polymers

The influence of the rigidity of polymer backbones on the side-chain crystallization and phase transition behavior was systematically investigated by a combination of differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), Fourier transform infrared spectroscopy (FTIR), and high-resolution solid-state nuclear magnetic resonance spectroscopy (NMR). DSC investigation indicated that the crystallization number of alkyl carbon atoms of the side chains grafted onto the rigid polymer backbone, poly(p-benzamide) (PBA), is much lower than that of the alkyl carbon atoms of the side chains grafted onto the flexible polymer backbone, poly(ethyleneimine) (PEI), implying that the conformational state of the polymer backbones has a strong effect on the side-chain crystallization behavior in comblike polymers. WAXD and FTIR results proved that these two comblike polymers pack into hexagonal (PBA18C) and orthorhombic (PEI18C) crystals, respectively, depending on the adjusting ability of the polymer backbones for particular conformational states. It was also found that the presence of the crystalline-amorphous interphase (delta = 31.6 ppm) in PBA18C detected by solid-state C-13 NMR spectroscopy can be attributed to the rigid PBA backbone, which restricts the mobility of the alkyl side chains.

Thermal and dynamic mechanical properties of PES/PPS blends

Blends of poly(ether-sulfone) (PES) and poly(phenylene sulfide) (PPS) with various compositions were prepared using an internal mixer at 290degreesC and 50 rpm for 10 min. The thermal and dynamic mechanical properties of PES/PPS blends have been investigated by means of DSC and DMA. The blends showed two glass transition temperatures corresponding to PPS-rich and PES-rich phases. Both of them decreased obviously for the blends with PES matrix. On the other hand, T-g of PPS and PES phase decreased a little when PPS is the continuous phase. In the blends quenched from molten state the cold crystallization temperature of PPS was detected in the blends of PES/PPS with mass ratio 50/50 and 60/40. The melting point, crystallization temperature and the crystallinity of blended PPS were nearly unaffected when the mass ratio of PES was less than 60%, however, when the amount of PES is over 60% in the blends, the crystallization of PPS chains was hindered. The thermal and the dynamic mechanical properties of the PPS/PES blends were mainly controlled by the continued phase.

Low threshold amplified spontaneous emission based on coumarin 151 encapsulated in mesoporous SBA-15

Amplified spontaneous emission (ASE) characteristics of a blue dye coumarin 151 encapsulated in a highly ordered mesoporous SBA-15 were studied. The spectra narrowing was observed and found that the threshold and loss were greatly reduced, and the gain is significantly increased compared with spin-coated coumarin 151 doped poly(4-vinylphenol) film. The ASE threshold, gain, and loss, respectively, reached 0.55 mJ pulse(-1) cm(-2), 44.78 cm(-1), and 8.9 cm(-1) for the coumarin 151 encapsulated in mesoporous SBA-15 film. The optimized lasing action owes much to the effects of the better spatial confinement of the molecules in the ordered mesoporous structure of the host SBA-15.

Polymer light-emitting diodes based on a bipolar transporting luminescent polymer

A soluble electroluminescent polymer containing hole-deficient triphenylamine and electron-deficient oxadiazole units in the main chains has been designed and studied. The design is based on the consideration that the triphenylamine group possesses good hole-transporting property and the oxadiazole unit is known to be of electron-transporting character. Because of the good bipolar transporting performance, the brightness and electroluminescent efficiency are significantly improved and the turn-on voltage is reduced compared with a similar polymer without the electron-deficient oxadiazole units in the main chains. For a device with configuration ITO/PEDOT/polymer/CsF/Al, a maximum brightness of 3600 cd m(-2) and a maximum luminescent efficiency of 0.65 cd A(-1) (quantum efficiency of 0.3%) were obtained in the polymer with oxadiazole units, about 15 times brighter and 15 times more efficient than the corresponding polymer without oxadiazole units.

Capillary electrophoresis with solid-state electrochemiluminescence detector

We report capillary electrophoresis coupling to a solid-state electrochemiluminescence (ECL) detector for the first time. The solid-state ECL detector was fabricated by immobilizing the ECL reagent tris(2,2'-bipyridyf)ruthenium (TBR) in poly-(p-styrenesulfonate)-silica-poly(vinyl alcohol) grafting 4-vinylpyridine copolymer films. The excellent stability of the solid-state ECL detector in the phosphate solution satisfied application in CE. The CE with solid-state ECL detector system was characterized using tripropylamine (TPA) and proline. The influences of detection potential, the concentration of TBR in the film, and pH value of ECL buffer were investigated. The linear range for TPA and proline was 0.005-10 muM and 5-10 mM with correlation coefficients of 0.997 and 0.998, respectively. The detection limit (signal-to-noise ratio S/N = 3) was estimated to be 0.002 and 2.0 muM for TPA and proline, respectively. The relative standard deviations for 1.0 pm TPA and 1.0 mm proline were 8.7% and 7.5% with theoretical plate numbers of 70 000 and 16 000, respectively. Compared with the CE-ECL of TBR in aqueous solution, the CE coupling with solid-state ECL detector system gave the same sensitivity of analysis.

Charge carrier mobility and electroluminescence in a green-emitting alternating block copolymer with a methoxy Bi-substituted chromophore

We determine the mobility of positive and negative charge carriers in a soluble green-emitting alternating block copolymer with, a methoxy bi-subsbituted conjugated segment. The negative charge carrier mobility of 6 x 10(-11) cm(2)/V.s is directly determined using space-charge-limited current analytical expressions. Positive charge carrier transport is also space-charge-limited, with a mobility of I x 10(-8) cm(2)/V.s. The electron trap distribution is exponential, with a characteristic energy of similar to 0.12 eV. A hole trap with energy similar to 0.4 eV was observed. This copolymer is used as emissive material in organic light-emitting diodes that present brightness of similar to 900 cd/m(2) at 12.5 V.

Charge transport in a blue-emitting alternating block copolymer with a small spacer to conjugated segment length ratio

We analyze current versus voltage data obtained using single carrier injection in several metal/polymer/metal sandwich structures. The polymer used in each case is a soluble blue-emitting alternating block copolymer. Our experimental results demonstrate that the electron transport is space-charge limited by the high density of traps having an exponential energy distribution (temperature dependent characteristic energy) in the copolymer. The electron mobility of 8x10(-10) cm(2)/V s is directly determined using space-charge-limited current analytical expressions. Hole transport is also space-charge limited, with a mobility of 2x10(-6) cm(2)/V s. A hole trap with energy 0.17 eV is observed. We compare these results with those obtained for related block copolymers with different spacer and conjugated segment lengths and discuss the influence of spacer length and conjugated segment length on the charge transport properties. (C) 2000 American Institute of Physics. [S0021-8979(00)04501-1].

Synthesis and characterization of alternating copolymers containing triphenylamine as hole-transporting units

A series of light-emitting poly(p-phenylene vinylene)s with triphenylamine units as hole-transporting moieties in the main chain were synthesized via Wittig condensation in good yields. The newly formed vinylene double bonds possessed a trans configuration, which was confirmed by Fourier transform infrared and NMR spectroscopy. The high glass-transition temperature (83-155 degreesC) and high decomposition temperature (> 300 degreesC) suggested that the resulting copolymers possessed high thermal stability. These copolymers, especially TAAPV1, possessed a high weight-average molecular weight (47,144) and a low polydispersity index (1.55). All the copolymers could be dissolved in common organic solvents, such as tetrahydrofuran (THF), CHCl3, CH2Cl2, and toluene, and exhibited intense photoluminesence in THF (the emission maxima were located from 478 to 535 nm) and in film (from 478 to 578 nm). The low onsets of the oxidation potential (0.6-0.75 V) suggested that the alternating copolymers possessed a good hole-transporting property due to the incorporation of triphenylamine moieties. (C) 2001 John Wiley & Sons, Inc.

Determination of electron mobility in a blue-emitting alternating block copolymer by space-charge-limited current measurements

In this communication we analyse current versus voltage data obtained using one carrier injection at metal/polymer/metal structures, The used polymer is a soluble blue-emitting alternating block copolymer, Our experimental results demonstrate that the electron current is limited by a large amount of traps with exponential energy distribution in the copolymer. The electron ;mobility of 5.1 x 10(-10) cm(2)/V s is directly determined by space-charge-limited current measurements. The electron mobility is at least three orders of magnitude smaller than that for holes in the copolymer. (C) 1999 Elsevier Science Ltd. All rights reserved.

Bright green organic electroluminescent devices based on a novel thermally stable terbium complex

A navel thermally stable terbium carboxylate complex, Tb(MTP)(3)(phen) (MTP=monotetradecyl phthalate, phen=1,10-phehanthroline), was synthesized and characterized. The device structure of glass substrate/indium-tin-oxide/poly(p-phenylenevinylene) (PPV)/poly (N-vinycarbazole) (PVK):Tb(MTP)(3)(phen): 1,3,4-oxadizole derivative (PBD)/tris(8-hydroxyquinoline) (Alq(3))/aluminum (Al) was employed to study the electroluminescent properties of Tb(MTP)(3)(phen). A green emission with extremely sharp spectral band of less than 10 nm at 544 nm peak wavelength was observed. A maximum luminance of 152 cd/m(2) and an external quantum efficiency of 0.017% were achieved at a drive voltage of 24 V. A possible mechanism of energy transfer based on the polymer doped with lanthanide organic complex was also proposed.

MICROSTRUCTURE ANALYSIS OF 3 SEGMENTED COPOLYMERS CONTAINING POLYDIMETHYLSILOXANE BY SOLID-STATE HIGH-RESOLUTION NMR

The microstructure of two bicomponent and one tricomponent segmented copolymers, based on polydimethylsiloxane, poly(p-hydroxystyrene) or/and polysulfone, were investigated using an extended Goldman-Shen pulse sequence, proton spin-spin relaxation measurements, and C-13 and Si-29 NMR spectra. The results indicate that there exist four phases with different sizes, components and morphological structure in the segmented copolymers studied in this work, i. e., a rigid-chain phase of very slow motion, a rigid-chain-rich phase of slow motion, a flexible-chain-rich phase of fast motion and a flexible-chain phase of faster motion. The sizes of different domains, calculated from the spin diffusion rates, are about 50-100 angstrom for the flexible-chain-rich phase of fast motion and 200-300 angstrom for the flexible-chain phase of faster motion. The relative quantities of polydimethylsiloxane in the flexible-chain phase of fast motion are slightly different in different kinds of segmented copolymers.

太湖表层沉积物中多磷酸盐检出的环境意义

在氮限制型富营养化湖泊中，沉积多磷酸盐（Poly-P）可以用来示踪营养盐磷的输入和湖泊的富营养化过程。太湖是一个典型的磷限制型富营养化湖泊，通过对太湖表层沉积物中总有机碳（TOC）、总氮（TN）、总磷（TP）、氢氧化钠可提取磷（NaOH-P）以及Poly-P 的提取分析，初步探讨了太湖营养盐磷输入的历史记录，并揭示了该湖Poly-P 的主要来源和保存机制。太湖Poly-P 的质量浓度较低，变化范围为0.004~0.065 mg·g-1。NaOH-P 占TP 组成的22%，是太湖沉积物总磷的主要组成部分之一。结果显示，在湖泊水体藻类生物量较大和NaOH-P 是沉积物TP 重要组成部分的磷限制型湖泊中，Poly-P 也是沉积物磷汇组成的一个重要部分，同时还是一个可以反映由人为磷输入增大导致湖泊富营养化程度加剧的敏感指标。

Caracterização e transformação de Lenhosulfonatos de Eucalyptus globulus

Os lenhosulfonatos representam um sub-produto formado durante o cozimento ao sulfito ácido, sendo queimados para a regeneração da base e recuperação de energia. No entanto, os lenhosulfonatos são também considerados uma importante matéria-prima para a produção de vários produtos de valor acrescentado. Os objectivos principais deste trabalho foram contribuir para uma melhor compreensão sobre a caracterização química e estrutural dos lenhosulfonatos do Eucalyptus globulus, assim como, para complementar a informação disponível sobre a síntese e a caracterização estrutural e térmica de materiais poliméricos obtidos a partir de compostos modelo dos produtos de oxidação dos lenhosulfonatos. O licor de cozimento ao sulfito foi analisado em termos do teor de cinzas, extractáveis, compostos voláteis, açúcares e lenhosulfonatos. O teor de cinzas e açúcares no licor de cozimento é muito elevado, tendo sido necessário purificar o mesmo (2,8-13,8 % e 3,2-9,1 %, respectivamente). A análise dos açúcares mostrou uma quantidade considerável de pentoses, sendo o açúcar predominante a xilose. Os lenhosulfonatos foram purificados, isolados e caracterizados por química molhada (titulação potenciométrica e oxidação com permanganato), análise elementar, espectroscopia de ultravioleta/visível (UV/Vis), espectroscopia de infravermelho de transformada de Fourier (FTIR), espectroscopia de ressonância magnética nuclear de protão (RMN de 1H) e carbono (RMN de 13C), espectrometria de massa de ionização por electrospray (ESI-MS), cromatografia de permeação em gel (GPC), termogavimetria (TGA) e calorimetria diferencial de varrimento (DSC). Os lenhosulfonatos são constituídos principalmente por unidades S, são parcialmente sulfonados e possuem um peso molecular relativamente baixo (Mw = 1250-2400 Da). A ruptura das ligações β-O-4 e α-O-4 da lenhina do Eucalyptus globulus após cozimento ao sulfito ácido originam olígomeros de baixo peso molecular cuja estrutura foi elucidada por RMN 1D/2D e ESI-MS. A degradação térmica dos lenhosulfonatos apresentou dois máximos de degradação a 188-190ºC e a 315-380ºC. As curvas de DSC mostraram um pico endotérmico para temperaturas inferiores a 130ºC e um pico exotérmico a 300-500ºC. Os lenhosulfonatos foram despolimerizados na presença de oxigénio molecular em meio alcalino. Os produtos de oxidação principais foram o aldeído siríngico, a vanilina, o ácido vanílico e o ácido siríngico. A adição do catalisador (sal de cobre) promoveu a oxidação dos lenhosulfonatos aumentando o rendimento dos aldeídos aromáticos (< 50%). A presença de açúcares nos lenhosulfonatos teve um efeito negativo no rendimento dos produtos de oxidação principais. Alguns compostos modelo dos produtos de oxidação dos lenhosulfonatos foram polimerizados por poliadição (catiónica e radicalar) e policondensação. Os monómeros e os polímeros foram caracterizados por espectroscopia de infravermelho de transformada de Fourier e reflectância total atenuada (FTIR-ATR), RMN em solução e no estado sólido, UV/Vis no estado sólido, GPC, difracção de raios-X (XRD), TGA e DSC. Os compostos modelo estudados foram os estirenos metoxi-substituídos (p-metoxiestireno e 3,4-dimetoxiestireno) e os ácidos hidroxi aromáticos metoxi-substituídos (ácido vanílico e ácido siríngico). O 3,4-dimetoxiestireno foi ainda copolimerizado com o éter isobutil vinílico e os seus copolímeros foram desmetilados, assim como, o poli(p-metoxiestireno) e o poli(3,4-dimetoxiestireno). A polimerização catiónica do p-metoxiestireno e 3,4-dimetoxiestireno é mais rápida e mais completa do que a polimerização radicalar produzindo polímeros com pesos moleculares elevados. O poli(p-metoxiestireno) (Mw = 235000 Da) possui um peso molecular maior do que o poli(3,4-dimetoxiestireno) (Mw = 18800 Da). A estabilidade térmica e a temperatura de transição vítrea diminuiram com a presença do segundo grupo metoxilo. A desmetilação dos homopolímeros foi bem sucedida, tendo sido corroborada por FTIR-ATR e RMN. A policondensação do ácido siríngico foi dificultada pela presença do segundo grupo metoxilo, tendo sido necessário adicionar uma maior quantidade do agente de condensação devido a factores estéricos. O poli(ácido vanílico) e poli(ácido siríngico) são insolúveis na maior parte dos solventes orgânicos, sendo parcialmente solúveis em clorofórmio, ácido triflúoracético, 1,1,2,2- tetracloroetano, dimetilsulfóxido, tetrahidrofurano, N,N’-dimetilformamida e 1,1,1,3,3,3-hexaflúor-2-propanol. A estabilidade térmica diminuiu com a presença do segundo grupo metoxilo e os dois polímeros não exibiram temperatura de transição vítrea. O poli(ácido vanílico) e poli(ácido siríngico) apresentaram uma estrutura muito cristalina (grau de cristalinidade 70% e 50%, respectivamente). O segundo grupo metoxilo aumentou o valor da absorvância, mas a forma do espectro de UV/Vis foi similar. A polimerização catiónica do éter isobutil vinílico resultou na produção de um polímero muito viscoso com peso molecular elevado (Mw = 20400 Da). A degradação térmica do polímero ocorreu em várias gamas de temperatura e foi completa (0% de resíduo a 800ºC). A copolimerização catiónica do 3,4-dimetoxiestireno com o éter isobutil vinílico foi realizada com proporções diferentes 80:20, 50:50 e 20:80. Os copolímeros apresentaram uma viscosidade elevada e um peso molecular baixo (Mw = 2000-4000 Da) que aumentou com a quantidade de éter isobutil vinílico. A degradação térmica dos copolímeros ocorreu também em várias gamas de temperatura, sendo a sua degradação completa (0,9-1,5% de resíduo a 800ºC). A desmetilação dos copolímeros não foi bem sucedida, tendo sido confirmada por FTIR-ATR e RMN.