Catalytic asymmetric transfer hydrogenation of ketones: recent advances

In this review, we consider the main processes for the asymmetric transfer hydrogenation of ketones from 2008 up today. The most effective organometallic compounds (derived from Ru, Rh, Ir, Fe, Os, Ni, Co, and Re) and chiral ligands (derived from amino alcohols, diamines, sulfur- and phosphorus-containing compounds, as well as heterocyclic systems) will be shown paying special attention to functionalized substrates, tandem reactions, processes under non-conventional conditions, supported catalysts, dynamic kinetic resolutions, the use of water as a green solvent, theoretical and experimental studies on reaction mechanisms, enzymatic processes, and finally applications to the total synthesis of biologically active organic molecules.

Structural characterisation of kaolinite : NaCl intercalate and its derivatives

Kaolinite:NaCl intercalates with basal layer dimensions of 0.95 and 1.25 nm have been prepared by direct reaction of saturated aqueous NaCl solution with well-crystallized source clay KGa-1. The intercalates and their thermal decomposition products have been studied by XRD, solid-state 23Na, 27Al, and 29Si MAS NMR, and FTIR. Intercalate yield is enhanced by dry grinding of kaolinite with NaCl prior to intercalation. The layered structure survives dehydroxylation of the kaolinite at 500°–600°C and persists to above 800°C with a resultant tetrahedral aluminosilicate framework. Excess NaCl can be readily removed by rinsing with water, producing an XRD ‘amorphous’ material. Upon heating at 900°C this material converts to a well-crystallized framework aluminosilicate closely related to low-camegieite, NaAlSiO4, some 350°C below its stability field. Reaction mechanisms are discussed and structural models proposed for each of these novel materials.

Synthesis and characterisation of titanium sol-gels in varied gravity environments

Sol-gel synthesis in varied gravity is only a relatively new topic in the literature and further investigation is required to explore its full potential as a method to synthesise novel materials. Although trialled for systems such as silica, the specific application of varied gravity synthesis to other sol-gel systems such as titanium has not previously been undertaken. Current literature methods for the synthesis of sol-gel material in reduced gravity could not be applied to titanium sol-gel processing, thus a new strategy had to be developed in this study. To successfully conduct experiments in varied gravity a refined titanium sol-gel chemical precursor had to be developed which allowed the single solution precursor to remain un-reactive at temperatures up to 50oC and only begin to react when exposed to a pressure decrease from a vacuum. Due to the new nature of this precursor, a thorough characterisation of the reaction precursors was subsequently undertaken with the use of techniques such as Nuclear Magnetic Resonance, Infra-red and UV-Vis spectroscopy in order to achieve sufficient understanding of precursor chemistry and kinetic stability. This understanding was then used to propose gelation reaction mechanisms under varied gravity conditions. Two unique reactor systems were designed and built with the specific purpose to allow the effects of varied gravity (high, normal, reduced) during synthesis of titanium sol-gels to be studied. The first system was a centrifuge capable of providing high gravity environments of up to 70 g’s for extended periods, whilst applying a 100 mbar vacuum and a temperature of 40-50oC to the reaction chambers. The second system to be used in the QUT Microgravity Drop Tower Facility was also required to provide the same thermal and vacuum conditions used in the centrifuge, but had to operate autonomously during free fall. Through the use of post synthesis characterisation techniques such as Raman Spectroscopy, X-Ray diffraction (XRD) and N2 adsorption, it was found that increased gravity levels during synthesis, had the greatest effect on the final products. Samples produced in reduced and normal gravity appeared to form amorphous gels containing very small particles with moderate surface areas. Whereas crystalline anatase (TiO2), was found to form in samples synthesised above 5 g with significant increases in crystallinity, particle size and surface area observed when samples were produced at gravity levels up to 70 g. It is proposed that for samples produced in higher gravity, an increased concentration gradient of water is forms at the bottom of the reacting film due to forced convection. The particles formed in higher gravity diffuse downward towards this excess of water, which favours the condensation reaction of remaining sol gel precursors with the particles promoting increased particle growth. Due to the removal of downward convection in reduced gravity, particle growth due to condensation reaction processes are physically hindered hydrolysis reactions favoured instead. Another significant finding from this work was that anatase could be produced at relatively low temperatures of 40-50oC instead of the conventional method of calcination above 450oC solely through sol-gel synthesis at higher gravity levels. It is hoped that the outcomes of this research will lead to an increased understanding of the effects of gravity on chemical synthesis of titanium sol-gel, potentially leading to the development of improved products suitable for diverse applications such as semiconductor or catalyst materials as well as significantly reducing production and energy costs through manufacturing these materials at significantly lower temperatures.

Synthesis and properties of fullerene C60 and C70 spin probes containing isoindoline nitroxides

Three fullerene isoindoline nitroxides N-methyl-3,4-fulleropyrrolidine-2-spiro-5′- (1′,1′,3′,3′-tetramethylisoindolin-2′-yloxyl), (C60-(TMIO)m, and C70-(TMIO)n) were synthesized by the covalent bonding of 5-formyl-1,1,3,3-tetramethyl isoindolin-2-yloxyl to the fullerenes C60 and C70. Significantly, the X-ray photoelectron spectra indicated the characteristic N 1s signals of NO. at 402 eV. The atomic force microscope morphologies showed that the average particle sizes of C60-(TMIO)m and C70-(TMIO)n were 38 and 15 nm. The electrochemical experiments indicated that fullerene bound isoindoline nitroxides retained similar electrochemical properties and redox reaction mechanisms as the parent nitroxides. The electron paramagnetic resonance spectra of the fullerene isoindoline nitroxides all exhibited the hyperfine splittings and characteristic spectra of tetramethyl isoindoline nitroxides, with typical nitroxide g-values and nitrogen isotropic hyperfine coupling constants. Therefore, these fullerene isoindoline nitroxides may be considered as potential candidates for novel biological spin probes using electron paramagnetic resonance spectroscopy.

Protein cross-linking with oxidative enzymes and transglutaminase : Effects in meat protein systems

The effects of tyrosinase, laccase and transglutaminase (TG) were studied in different meat protein systems. The study was focused on the effects of the enzymes on the gel formation properties of myofibrils, and on the textural and water-holding properties of the heated meat systems. The cross-linking efficiency of a novel Trichoderma reesei tyrosinase was compared to that of the commercial Agaricus bisporus tyrosinase. Trichoderma tyrosinase was found to be superior compared to the Agaricus enzyme in its protein cross-linking efficiency and in the incorporation of a small molecule into a complex proteinaceous substrate. Tyrosinase, laccase and TG all polymerised myofibrillar proteins, but laccase was also found to cause protein fragmentation. A positive connection between covalent cross-link and gel formation was observed with tyrosinase and TG. Laccase was able to increase the gel formation only slightly. With an excessive laccase dosage the gel formation declined due to protein fragmentation. Tyrosinase, laccase and TG had different effects on the texture and water-holding of the heated chicken breast meat homogenates. Tyrosinase improved the firmness of the homogenate gels free of phosphate and with a low amount of meat. TG improved the firmness of all studied homogenates. Laccase weakened the gel firmness of the low-meat, low-salt and low-salt/phosphate homogenates and maintained the firmness on the control level in the homogenate free of phosphate. Tyrosinase was the only enzyme capable of reducing the weight loss in the homogenates containing a low amount of meat and a low amount of NaCl. TG was the only enzyme that could positively affect the firmness of the homogenate gel containing both low NaCl and phosphate amounts. In pilot scale the test products were made of coarsely ground chicken breast fillet with a moderate amount of salt. Increasining the amount of meat, salt and TG contents favoured the development of firmness of the test products. The evaporation loss decreased slightly along with increasing TG and NaCl amounts in the experimental conditions used, indicating a positive interaction between these two factors. In this work it was shown that tyrosinase, laccase and TG affected the same myofibrillar proteins, i.e. myosin and troponin T. However, these enzymes had distinguishable effects on the gel formation of a myofibril system as well as on the textural and water-holding properties of the finely ground meat homogenates, reflecting distinctions at least in the reaction mechanisms and target amino acid availability in the protein substrates for these enzymes.

Kemian ylioppilaskokeen tehtävät summatiivisen arvioinnin välineenä

The main purpose of the research was to illustrate chemistry matriculation examination questions as a summative assessment tool, and represent how the questions have evolved over the years. Summative assessment and its various test item classifications, Finnish goal-oriented curriculum model, and Bloom’s Revised Taxonomy of Cognitive Objectives formed the theoretical framework for the research. The research data consisted of 257 chemistry questions from 28 matriculation examinations between 1996 and 2009. The analysed test questions were formulated according to the national upper secondary school chemistry curricula 1994, and 2003. Qualitative approach and theory-driven content analysis method were employed in the research. Peer review was used to guarantee the reliability of the results. The research was guided by the following questions: (a) What kinds of test item formats are used in chemistry matriculation examinations? (b) How the fundamentals of chemistry are included in the chemistry matriculation examination questions? (c) What kinds of cognitive knowledge and skills do the chemistry matriculation examination questions require? The research indicates that summative assessment was used diversely in chemistry matriculation examinations. The tests included various test item formats, and their combinations. The majority of the test questions were constructed-response items that were either verbal, quantitative, or experimental questions, symbol questions, or combinations of the aforementioned. The studied chemistry matriculation examinations seldom included selected-response items that can be either multiple-choice, alternate choice, or matching items. The relative emphasis of the test item formats differed slightly depending on whether the test was a part of an extensive general studies battery of tests in sciences and humanities, or a subject-specific test. The classification framework developed in the research can be applied in chemistry and science education, and also in educational research. Chemistry matriculation examinations are based on the goal-oriented curriculum model, and cover relatively well the fundamentals of chemistry included in the national curriculum. Most of the test questions related to the symbolism of chemical equation, inorganic and organic reaction types and applications, the bonding and spatial structure in organic compounds, and stoichiometry problems. Only a few questions related to electrolysis, polymers, or buffer solutions. None of the test questions related to composites. There were not any significant differences in the emphasis between the tests formulated according to the national curriculum 1994 or 2003. Chemistry matriculation examinations are cognitively demanding. The research shows that the majority of the test questions require higher-order cognitive skills. Most of the questions required analysis of procedural knowledge. The questions that only required remembering or processing metacognitive knowledge, were not included in the research data. The required knowledge and skill level varied slightly between the test questions in the extensive general studies battery of tests in sciences and humanities, and subject-specific tests administered since 2006. The proportion of the Finnish chemistry matriculation examination questions requiring higher-order cognitive knowledge and skills is very large compared to what is discussed in the research literature.

In-situ one-step hydrothermal synthesis of a lead germanate-graphene composite as a novel anode material for lithium-ion batteries

Lead germanate-graphene nanosheets (PbGeO3-GNS) composites have been prepared by an efficient one-step, in-situ hydrothermal method and were used as anode materials for Li-ion batteries (LIBs). The PbGeO3 nanowires, around 100–200 nm in diameter, are highly encapsulated in a graphene matrix. The lithiation and de-lithiation reaction mechanisms of the PbGeO3 anode during the charge-discharge processes have been investigated by X-ray diffraction and electrochemical characterization. Compared with pure PbGeO3 anode, dramatic improvements in the electrochemical performance of the composite anodes have been obtained. In the voltage window of 0.01–1.50 V, the composite anode with 20 wt.% GNS delivers a discharge capacity of 607 mAh g−1 at 100 mA g−1 after 50 cycles. Even at a high current density of 1600 mA g−1, a capacity of 406 mAh g−1 can be achieved. Therefore, the PbGeO3-GNS composite can be considered as a potential anode material for lithium ion batteries.

Vapour phase synthesis of salol over solid acids via transesterification

The transesterification of methyl salicylate with phenol has been studied in vapour phase over solid acid catalysts such as ZrO2, MoO3 and SO42- or Mo(VI) ions modified zirconia. The catalytic materials were prepared and characterized for their total surface acidity, BET surface area and powder XRD patterns. The effect of mole-ratio of the reactants, catalyst bed temperature, catalyst weight, flow-rate of reactants, WHSV and time-on-stream on the conversion (%) of phenol and selectivity (%) of salol has been investigated. A good yield (up to 70%) of salol with 90% selectivity was observed when the reactions were carried out at a catalyst bed temperature of 200 degrees C and flow-rate of 10 mL/h in presence of Mo(VI)/ZrO2 as catalyst. The results have been interpreted based on the variation of acidic properties and powder XRD phases of zirconia on incorporation of SO42- or Mo(VI) ions. The effect of poisoning of acid sites of SO42- or Mo(VI) ions modified zirconia on total surface acidity, powder XRD phases and catalytic activity was also studied. Possible reaction mechanisms for the formation of salol and diphenyl ether over acid sites are proposed.

Bicyclic Phosphazenes Derived from (Amino) Cyclotetraphosphazenes

Amination reactions of 2,6-bis(primary amino)cyclotetraphosphazenes yield not only the expected (amino)cyclotetraphosphazenes but also novel trans-annular bridged bicyclic phosphazenes by an intramolecular substitution pathway. In addition, resins are formed in some reactions by an intermolecular condensation. The effect of substituents attached to the phosphazene ring, the attacking nucleophile and solvent on the formation of the trans-annular P-N-P bridge is considered in detail in relation to plausible reaction mechanisms. Analytical separation of bicyclic phosphazenes by high performance liquid chromatography (HPLC) on a reverse phase silica column is demonstrated. Structural features of bicyclic phosphazenes and salient aspects of their NVR spectroscopic data are discussed.

Time-Resolved Resonance Raman Spectroscopy: Exploring Reactive Intermediates

The study of reaction mechanisms involves systematic investigations of the correlation between structure, reactivity, and time. The challenge is to be able to observe the chemical changes undergone by reactants as they change into products via one or several intermediates such as electronic excited states (singlet and triplet), radicals, radical ions, carbocations, carbanions, carbenes, nitrenes, nitrinium ions, etc. The vast array of intermediates and timescales means there is no single ``do-it-all'' technique. The simultaneous advances in contemporary time-resolved Raman spectroscopic techniques and computational methods have done much towards visualizing molecular fingerprint snapshots of the reactive intermediates in the microsecond to femtosecond time domain. Raman spectroscopy and its sensitive counterpart resonance Raman spectroscopy have been well proven as means for determining molecular structure, chemical bonding, reactivity, and dynamics of short-lived intermediates in solution phase and are advantageous in comparison to commonly used time-resolved absorption and emission spectroscopy. Today time-resolved Raman spectroscopy is a mature technique; its development owes much to the advent of pulsed tunable lasers, highly efficient spectrometers, and high speed, highly sensitive multichannel detectors able to collect a complete spectrum. This review article will provide a brief chronological development of the experimental setup and demonstrate how experimentalists have conquered numerous challenges to obtain background-free (removing fluorescence), intense, and highly spectrally resolved Raman spectra in the nanosecond to microsecond (ns-mu s) and picosecond (ps) time domains and, perhaps surprisingly, laid the foundations for new techniques such as spatially offset Raman spectroscopy.

A detailed numerical study of NOx kinetics in low calorific value H-2/CO syngas flames

The present study provides an extensive and detailed numerical analysis of NO chemical kinetics in low calorific value H-2/CO syngas flames utilizing predictions by five chemical kinetic mechanisms available out of which four deal with H-2/CO while the fifth mechanism (GRI 3.0) additionally accounts for hydrocarbon chemistry. Comparison of predicted axial NO profiles in premixed flat flames with measurements at 1 bar, 3.05 bar and 9.15 bar shows considerably large quantitative differences among the various mechanisms. However, at each pressure, the quantitative reaction path diagrams show similar NO formation pathways for most of the mechanisms. Interestingly, in counterflow diffusion flames, the quantitative reaction path diagrams and sensitivity analyses using the various mechanisms reveal major differences in the NO formation pathways and reaction rates of important reactions. The NNH and N2O intermediate pathways are found to be the major contributors for NO formation in all the reaction mechanisms except GRI 3.0 in syngas diffusion flames. The GRI 3.0 mechanism is observed to predict prompt NO pathway as the major contributing pathway to NO formation. This is attributed to prediction of a large concentration of CH radical by the GRI 3.0 as opposed to a relatively negligible value predicted by all other mechanisms. Also, the back-conversion of NNH into N2O at lower pressures (2-4 bar) was uniquely observed for one of the five mechanisms. The net reaction rates and peak flame temperatures are used to correlate and explain the differences observed in the peak NO] at different pressures. This study identifies key reactions needing assessment and also highlights the need for experimental data in syngas diffusion flames in order to assess and optimize H-2/CO and nitrogen chemistry. Copyright (C) 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

Laminar Burning Velocities and Markstein Lengths of Premixed Methane/Air Flames near the Lean Flammability Limit in Microgravity

Effects of flame stretch on the laminar burning velocities of near-limit fuel-lean methane/air flames have been studied experimentally using a microgravity environment to minimize the complications of buoyancy. Outwardly propagating spherical flames were employed to assess the sensitivities of the laminar burning velocity to flame stretch, represented by Markstein lengths, and the fundamental laminar burning velocities of unstretched flames. Resulting data were reported for methane/air mixtures at ambient temperature and pressure, over the specific range of equivalence ratio that extended from 0.512 (the microgravity flammability limit found in the combustion chamber) to 0.601. Present measurements of unstretched laminar burning velocities were in good agreement with the unique existing microgravity data set at all measured equivalence ratios. Most of previous 1-g experiments using a variety of experimental techniques, however, appeared to give significantly higher burning velocities than the microgravity results. Furthermore, the burning velocities predicted by three chemical reaction mechanisms, which have been tuned primarily under off-limit conditions, were also considerably higher than the present experimental data. Additional results of the present investigation were derived for the overall activation energy and corresponding Zeldovich numbers, and the variation of the global flame Lewis numbers with equivalence ratio. The implications of these results were discussed. 2010 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Mechanistic and reactivity studies of bent metallocene complexes of niobium and tantalum

A variety of olefin hydride complexes of niobium and tantalum has been prepared in order to study their reactivity and to gain insight into organometallic reaction mechanisms. Examination of a series of ethylene and propylene complexes of niobocene (CP_2Nb; Cp = η^5-C_5H_5), permethylniobocene (Cp*_2Nb; Cp* = η^5-C_5(CH_3)_5), tantalocene, and permethyltantalocene has indicated that there are both large electronic and steric effects deriving from the metal (and its ancillary ligands) in the olefin insertion (β-migratory insertion) process. Furthermore, a thermodynamic and kinetic analysis has been completed for a series of substituted styrene complexes of niobocene in order to better understand the important electronic properties of the olefin. The results are in accord with a concerted four-center process with only moderate charge development.

The special case of β-migratory insertion of a hydride ligand into coordinated benzyne has also been studied for the permethyltantalocene system. The coordinatively unsaturated (sixteen electron) phenyl tautomer, which is made accessible by the facile benzyne hydride insertion reaction, readily reacts with a variety of ligands, L, to afford Cp*_2 Ta(C_6H_5)L complexes (L = CO, O_2, NC≡R, :CH_2, H_2, etc.). This family of compounds exhibits interesting reactivity (a-migratory insertion, O_2 activation, and reductive elimination) which is discussed in some detail.

Finally a series of paramagnetic seventeen electron Cp*_2 TaX_2 (X = halide, alkyl, hydride) complexes, and the corresponding cationic and anionic species, have been prepared and studied. The odd electron neutral complexes exhibit surprising thermal stability and undergo very little reactivity. While the chemistry of the anionic compounds is almost completely dominated by their potent reducing power, that of the cations is quite diverse and amenable for study. Therefore the syntheses and reactivity (1 ,2-eliminations, ligand insertions, and deprotonation reactions) of these coordinatively unsaturated sixteen electron species are presented.

Bis(thiophenolate)pyridine pincer ligands and trivalent zirconocene complexes relevant to early transition metal polymerization catalysts

Two major topics are covered: the first chapter is focused on the development of post-metallocene complexes for propylene polymerization. The second and third chapters investigate the consequences of diisobutylaluminum hydride (HAlⁱBu₂) additives in zirconocene based polymerization systems.

The synthesis, structure, and solution behavior of early metal complexes with a new tridentate LX₂ type ligand, bis(thiophenolate)pyridine ((SNS) = (2-C₆H₄S)₂-2,6-C₅H₃N) are investigated. SNS complexes of Ti, Zr, and Ta having dialkylamido coligands were synthesized and structurally characterized. The zirconium complex, (SNS)Zr(NMe₂)₂, displays C₂ symmetry in the solid state. Solid-state structures of tantalum complexes (SNS)Ta(NMe₂)₃ and (SNS)TaCl(NEt₂)₂ also display pronounced C₂ twisting of the SNS ligand. 1D and 2D NMR experiments show that (SNS)Ta(NMe₂)₃ is fluxional with rotation about the Ta N(amide) bonds occurring on the NMR timescale. The fluxional behavior of (SNS)TaCl(NEt₂)₂ in solution was also studied by variable temperature ¹H NMR. Observation of separate signals for the diastereotopic protons of the methylene unit of the diethylamide indicates that the complex remains locked on the NMR timescale in one diastereomeric conformation at temperatures below -50 °C.

Reduction of Zr(IV) metallocenium cations with sodium amalgam (NaHg) produces EPR signals assignable to Zr(III) metallocene complexes. Thus, chloro-bridged heterobinuclear ansa-zirconocenium cation [((SBI))Zr(μ-Cl)₂AlMe₂]⁺B(C₆F₅)_4¯ (SBI = rac-dimethylsilylbis(1-indenyl)), gives rise to an EPR signal assignable to the complex (SBI)Zr^III(μ-Cl)₂AlMe₂, while (SBI)Zr^III-Me and (SBI)Zr^III(-H)2AlⁱBu₂ are formed by reduction of [(SBI)Zr(μ-Me)₂AlMe₂]⁺B(C₆F₅)_4¯ and [(SBI)Zr(μ-H)₃(AlⁱBu₂)₂]⁺B(C₆F₅)4¯, respectively. These products are also formed, along with (SBI)Zr^III-ⁱBu and [(SBI)Zr^III]⁺ AlR4¯ when (SBI)ZrMe₂ reacts with HAlⁱBu₂, eliminating isobutane en route to the Zr(III) complex. Studies concerning the interconversion reactions between these and other (SBI)Zr(III) complexes and reaction mechanisms involved in their formation are also reported.

The addition of HAlⁱBu₂ to precatalyst [(SBI)Zr(µ-H)₃(AlⁱBu₂)₂]⁺ significantly slows the polymerization of propylene and changes the kinetics of polymerization from 1st to 2nd order with respect to propylene. This is likely due to competitive inhibition by HAlⁱBu₂. When the same reaction is investigated using [(ⁿBuCp)₂Zr(μ-H)₃(AlⁱBu₂)₂]⁺, hydroalumination between propylene and HAlⁱBu₂ is observed instead of propylene polymerization.

Autoignition of alcohols and ethers in a rapid compression machine

The autoignition characteristics of methanol, ethanol and MTBE (methyl tert-butyl ether) have been investigated in a rapid compression machine at pressures in the range 20-40 atm and temperatures within 750-1000 K. All three oxygenated fuels tested show higher autoignition temperatures than paraffins, a trend consistent with the high octane number of these fuels. The autoignition delay time for methanol was slightly lower than predicted values using reported reaction mechanisms. However, the experimental and measured values for the activation energy are in very good agreement around 44 kcal/mol. The measured activation energy for ethanol autoignition is in good agreement with previous shock tube results (31 kcal/mol), although ignition times predicted by the shock tube correlation are a factor of three lower than the measured values. The measured activation energy for MTBE, 41.4 kcal/mol, was significantly higher than the value previously observed in shock tubes (28.1 kcal/mol). The onset of preignition, characterized by a slow energy release prior to early ignition was observed in some instances. Possible reasons for these ocurrences are discussed. © Copyright 1993 Society of Automotive engineers, Inc.