Modelagem e otimização por metodologia de superfícies de resposta: um estudo em arames de aço SAE 9254 para molas automobilísticas

Pós-graduação em Engenharia Mecânica - FEG

Desenvolvimento de vasos digestores de amostra para microondas doméstico

The application of microwave radiation on the sample preparation has been expanding increasingly in areas involving decomposition by wet and dry roads, fusion, extraction, acceleration of chemical reactions, for example. Currently, the use of microwave ovens for analytical purposes are recognized for having excellent performance for organic and inorganic samples. In the international market there are several kinds of microwaves oven which adapt the varied purposes, however yet with elevated prices which incapacitate your use as routine equipment in laboratory. Thus, many researchers have been choosing for developing own projects of microwaves oven production or to use domestic oven for the laboratory, with or without adaptations. For the evaluation of the proposed method was used in the Kjeldahl methodology for determining total nitrogen in samples of crude protein, using a domestic microwave oven and a digester pot made up in TeflonTM and distillation by steam. Were made to adapt and characterization of a domestic microwave oven, the confeccion vessel digester and the metal support for the vessel. The accuracy of the proposed method was confirmed by comparison of two methods, the standard method for conventional heating and by the proposed method, with heating by microwave radiation through the calculated values of relative standard deviation analysis

Short steel and concrete columns under high temperatures

The growing demand for knowledge about the effect of high temperatures on structures has stimulated increasing research worldwide. This article presents experimental results for short composite steel and concrete columns subjected to high temperatures in ovens with or without an axial compression load, numerically analyzes the temperature distribution in these columns after 30 and 60 minutes and compares them with experimental results. The models consist of concrete-filled tubes of three different thicknesses and two different diameters, and the concrete fill has conventional properties that remained constant for all of the models. The stress-strain behavior of the composite columns was altered after exposure to high temperatures relative to the same columns at room temperature, which was most evident in the 60-minute tests due to the higher temperatures reached. The computational analysis adopted temperature rise curves that were obtained experimentally.

B3a km 19 - ein linienbandkeramischer Fundplatz bei Friedberg, Wetteraukreis

Durch den Straßenbau an der Bundesstraße B3a veranlasst, wurden im Zeitraum vom 13.08.2007 bis zum 07.12.2007 archäologische Untersuchungen im Bereich der Streckenkilometer 19 bis 22 durch die Firma Archbau Essen, unter Kontrolle des Landesamtes für Denkmalpflege Hessen und der Kreisarchäologie Wetteraukreis durchgeführt. Bei km 19 wurde dabei eine Siedlung mit angrenzendem Gräberfeld aus der Linienbandkeramik (im Folgenden als LBK bezeichnet) festgestellt. Daneben ergaben sich eine Bestattung und ein Erdwerk der Michelsberger Kultur, Grubenkomplexe und ein Bronzehort aus der Urnenfelderkultur sowie eine mittelalterliche Straße.Heute liegt die Fundstelle Friedberg B3a km 19 in der südlichen Wetterau 30 km nördlich von Frankfurt am Main in Hessen an der Wetter 140 m über NN und gehört zum Wetteraukreis. rnDie 21 ha messende Ausgrabungsfläche umfasste insgesamt 344 Befunde. Die Identifikation der bandkeramischen Strukturen erfolgte hierbei vorwiegend durch die vergesellschaftete Keramik. Von zentraler Bedeutung sind die fünf Hausgrundrisse A bis E im nördlichen Sektor der Fundstelle, wobei die Präsenz zahlreicher „Dreipfostenriegel“ sowie die Nordost-Südwest Ausrichtung der Strukturen als Belege für eine Zeitstellung innerhalb der LBK angesehen werden. Über die Korrespondenzanalyse der bei den Siedlungsstrukturen angetroffenen Keramik konnte darüber hinaus eine Abfolge von Hausgenerationen erstellt werden. Daneben existierten eine Reihe weiterer Befunde von LBK-zeitlichen Pfostenstellungen, bei denen es sich um Zäune oder Palisaden gehandelt haben könnte. Südwestlich dieser Hausgrundrisse wurde bei den Ausgrabungen eine Grabenstruktur geschnitten, für die eine Funktion als Einfassung der bandkeramischen Siedlungsstrukturen möglich ist. Südlich dieser Grabenstruktur konnten sechs Hockerbestattungen der LBK festgestellt werden. Die räumliche Anordnung im Bereich der westlichen Grabungsgrenze lässt den Schluss zu, dass es sich hierbei um ein Gräberfeld handelt, welches bisher nur zu einem geringen Teil ergraben wurde. Ein Zusammenhang zu den Hausgrundrissen A bis E kann erwogen werden. Der nördliche Sektor der Fundstelle umfasste außerdem zahlreiche Grubenbefunde der LBK sowie einige Grubenkomplexe, wobei letztere als Lehmentnahmegruben anzusprechen sind. Abschließend soll hier noch auf die Existenz zweier bandkeramischer Öfen, darunter ein Grubenofen, im Südosten von Friedberg B3a km 19 hingewiesen werden. rnDen mit Abstand größten Anteil am bandkeramischen Fundmaterial aus Friedberg B3 km 19 hatte die Keramik mit 3428 Elementen. An Steingeräten konnten nur 12 Silices sowie 4 Beile und 14 Mahlsteine über die Typologie und die vergesellschaftete Keramik in die LBK eingeordnet werden. Bei den Knochengeräten zeigte sich ein einzelner beschädigter Kamm. Der Fokus der Analysen des bandkeramischen Fundmaterials aus Friedberg B3a km 19 lag auf der Keramik und deren Auswertung innerhalb von Seriation und Korrespondenzanalyse. Um den Untersuchungen mehr Validität zu verleihen und eine optimale Einordnung zu erreichen, wurden die Keramik-Daten aus Friedberg B3a km 19 mit anderen Datensätzen aus Südhessen kombiniert. Dabei war nicht nur die räumliche Nähe der Fundstellen entscheidend, sondern auch die stilistisch-typologische Nähe der Inventare. In Friedberg B3a km 19 waren die Phasen nach Meier-Arendt von einem frühen III bis zum Ende der Phase V anwesend. Phase II kann nur als marginal angesprochen werden. Es ließ sich kein Übergang zum Mittelneolithikum fassen. Nach der Interpretation aller relativchronologischer Daten könnte es sich in Friedberg B3a km 19 um eine Hausentwicklung mit sieben Phasen à 25 Jahren über 175 bis zu 200 Jahren handeln, die eine kontinuierliche Belegung des Platzes von der mittleren bis zum Ende der jüngsten LBK beschreibt. Insgesamt pflegt sich die Fundstelle Friedberg B3a km 19 so in die bandkeramische Siedlungslandschaft der südlichen Wetterau ein.

Desarrollo de un sistema automático de medida para el control del consumo en sistemas empotrados

El Grupo de Diseño Electrónico y Microelectrónico de la Universidad Politécnica de Madrid -GDEM- se dedica, entre otras cosas, al estudio y mejora del consumo en sistemas empotrados. Es en este lugar y sobre este tema donde el proyecto a exponer ha tomado forma y desarrollo. Según un artículo de la revista online Revista de Electrónica Embebida, un sistema empotrado o embebido es aquel “sistema controlado por un microprocesador y que gracias a la programación que incorpora o que se le debe incorporar, realiza una función específica para la que ha sido diseñado, integrando en su interior la mayoría de los elementos necesarios para realizar dicho función”. El porqué de estudiar sobre este tema responde a que, cada vez, hay mayor presencia de sistemas empotrados en nuestra vida cotidiana. Esto es debido a que se está tendiendo a dotar de “inteligencia” a todo lo que puedan hacer nuestra vida un poco más fácil. Nos podemos encontrar dichos sistemas en fábricas, oficinas de atención a los ciudadanos, sistemas de seguridad de hogar, relojes, móviles, lavadoras, hornos, aspiradores y un largo etcétera en cualquier aparato que nos podamos imaginar. A pesar de sus grandes ventajas, aún hay grandes inconvenientes. El mayor problema que supone a día de hoy es la autonomía del mismo sistema, ya que hablamos de aparatos que muchas veces están alimentados por baterías -para ayudar a su portabilidad–. Por esto, se está intentando dotar a dichos sistemas de una capacidad de ahorro de energía y toma de decisiones que podrían ayudar a duplicar la autonomía de dicha batería. Un ejemplo claro son los Smartphones de hoy en día, unos aparatos casi indispensables que pueden tener una autonomía de un día. Esto es poco práctico para el usuario en caso de viajes, trabajo u otras situaciones en las que se le dé mucho uso y no pueda tener acceso a una red eléctrica. Es por esto que surge la necesidad de investigar, sin necesidad de mejorar el hardware del sistema, una manera de mejorar esta situación. Este proyecto trabajará en esa línea creando un sistema automático de medida el cual generará las corrientes que servirán como entrada para verificar el sistema de adquisición que junto con la tarjeta Beagle Board permitirá la toma de decisiones en relación con el consumo de energía. Para realizar este sistema, nos ayudaremos de diferentes herramientas que podremos encontrar en el laboratorio del GDEM, como la fuente de alimentación Agilent y la Beagle Board –como principales herramientas de trabajo- . El objetivo principal será la simulación de unas señales que, después de pasar un proceso de conversión y tratado, harán la función de representación del consumo de cada una de las partes que pueden formar un sistema empotrado genérico. Por lo tanto, podemos decir que el sistema hará la funcionalidad de un banco de pruebas que ayudará a simular dicho consumo para que el microprocesador del sistema pueda llegar a tomar alguna decisión. ABSTRACT. The Electronic and Microelectronic Design Group of Universidad Politécnica de Madrid -GDEM- is in charge, between other issues, of improving the embedded system’s consumption. It is in this place and about this subject where the exposed project has taken shape and development. According to an article from de online magazine Revista de Electronica Embebida, an embedded system is “the one controlled by a microprocessor and, thanks to the programing that it includes, it carries out a specific function what it has been designed for, being integrated in it the most necessary elements for realizing the already said function”. The because of studying this subject, answers that each time there is more presence of the embedded system in our daily life. This is due to the tendency of providing “intelligence” to all what can make our lives easier. We can find this kind of systems in factories, offices, security systems, watchers, mobile phones, washing machines, ovens, hoovers and, definitely, in all kind of machines what we can think of. Despite its large vantages, there are still some inconveniences. Nowadays, the most important problem is the autonomy of the system itself when machines that have to be supplied by batteries –making easier the portability-. Therefore, this project is going after a save capacity of energy for the system as well as being able to take decisions in order to duplicate batteries’ autonomy. Smartphones are a clear example. They are a very successful product but the autonomy is just one day. This is not practical for users, at all, if they have to travel, to work or to do any activity that involves a huge use of the phone without a socket nearby. That is why the need of investigating a way to improve this situation. This project is working on this line, creating an automatic system that will generate the currents for verifying the acquisition system that, with the beagle board, will help taking decisions regarding the energy’s consumption. To carry out this system, we need different tools that we can find in the laboratory of the group previously mentioned, like power supply Agilent and the Beagle Board – as main working tools –. The main goal is the simulation of some signals that, after a conversion process, will represent de consumption of each of the parts in the embedded generic system. Therefore, the system will be a testing ground that simulate the consumption, once sent to the processor, to be processed and so the microprocessor system might take some decision.

Allgemeine deutsche Biographie ... : Auf Veranlassung ... /

"Generalregister" by Fritz Gerlich: v. 56.

The development of heat recovery equipment from conception to commercialisation

A comprehensive survey of industrial sites and heat recovery products revealed gaps between equipment that was required and that which was available. Two heat recovery products were developed to fill those gaps: a gas-to-gas modular heat recovery unit; a gas-to-liquid exhaust gas heat exchanger. The former provided an entire heat recovery system in one unit. It was specifically designed to overcome the problems associated with existing component system of large design commitment, extensive installation and incompatibility between parts. The unit was intended to recover heat from multiple waste gas sources and, in particular, from baking ovens. A survey of the baking industry defined typical waste gas temperatures and flow rates, around which the unit was designed. The second unit was designed to recover heat from the exhaust gases of small diesel engines. The developed unit differed from existing designs by having a negligible effect on engine performance. In marketing terms these products are conceptual opposites. The first, a 'product-push' product generated from site and product surveys, required marketing following design. The second, a 'market-pull' product, resulted from a specific user need; this had a captive market and did not require marketing. Here marketing was replaced by commercial aspects including the protection of ideas, contracting, tendering and insurance requirements. These two product development routes are compared and contrasted. As a general conclusion this work suggests that it can be beneficial for small companies (as was the sponsor of this project) to undertake projects of the market-pull type. Generally they have a higher probability of success and are less capital intensive than their product-push counterparts. Development revealed shortcomings in three other fields: British Standards governing heat exchangers; financial assessment of energy saving schemes; degree day procedure of calculating energy savings. Methods are proposed to overcome these shortcomings.

Estudo comparativo da capacidade de assamento de dois fornos solares com diferentes configurações

This research is presented as a comparative study about the baking capacity of two box type ovens, produced from a packing case used to equipment transportation. The two ovens have different internal settings, with the greenhouse effect and the concentration of incident solar radiation as the main parameters of differentiation. The main features of the ovens are the low cost, the reuse of materials, the manufacturing and assembly processes simplified, the easy management and the ability of baking a variety of foods simultaneously. The manufacturing and operation of the ovens can be handled by any social and intellectual level of people. The feasibility of the ovens to bake the tested foods was proved with success, ensuring the supremacy of the mirrored oven. The results obtained for both ovens were competitive even with the conventional gas oven, producing the baking of three cakes with 750g in just 80 minutes.

Caracterização de superfícies seletivas de frequência de periódicas e não-periódicas

The past years have seen a great interest in the use of frequency selective surfaces (FSS), as spatial filters, in many microwave applications. Among these, we highlight applications in telecommunication systems (such as satellite communications and radar), high gain antennas (combined with planar antennas) and (home and industrial) microwave ovens. The FSS is usually composed of two-dimensional periodic arrays, with equally spaced elements, which may be metallic patches (printed on dielectric substrates) or aperture (holes in thin metal surfaces). Using periodic arrays, the FSS have been able to meet the demands of the telecommunications industry. However, new demands are finding technological limitations. In this context, adverse filtering requirements have forced designers to use FSS optimization methods to find specific formats of FSS elements. Another alternative that has been used to increase the selectivity of the FSS is the cascaded FSS, a simple technique that has as main drawback the increased dimensions of the structure, as well as its weight. This work proposes the development of a new class of selective surfaces frequency (FSS) composed of quasi-periodic (or non-periodic) arrangements. The proposed FSS have no array periodicity, in relation with the spatial position of their elements. The frequency responses of these structures were simulated using commercial softwares that implement full-wave methods. For the purpose of validation of this study, FSS prototypes were built and measured, being possible to observe a good agreement between simulated and measured results. The main conclusions of this work are presented, as well as suggestions for future works.

Fabricação e estudo de um forno solar com dispositivo de transporte

It presents a solar oven manufactured from MDF boards intended for the baking of foods such as pizza, cakes, breads, hamburgers and the like. They will be given the manufacturing processes and assembly of such an oven which has features of low cost manufacturing. The main feature of the proposed furnace and can be transported to any locations because it is seated on a device for carrying case / backpack. Tests will be conducted for the baking of various foods and their results will be compared with the various types of existing solar ovens shown by the literature. They will analyze the thermal and economic feasibility of such an oven that can provide socialization of the use of solar energy for poor communities and can become a source of generation of employment and income. The proposed solar oven baking has capacity for two foods and can be manufactured to allow multiple simultaneous baking of food.

Obtenção e caracterização de um compósito de matriz polimérica com carga de resíduos vegetal proveniente do sabugo de milho

The feasibility of using the corn cob to obtain a polymer matrix composite was studied. To obtain the bran, corncob passed the drying process in a solar dryer, and was subsequently triturated in forage and to obtain the different particle sizes, by sieving. Three different grain sizes were used: fine particles (FP) size between 0,10 and 2mm; sized particles (PM) with sizes between 2,10 and 3,35 mm; large particles (PG) sizes between 3,45 and 4,10 mm. Using 20% of residue relative to the resin, the test samples were constructed for characterization of the composite, taking into account thermal and mechanical parameters. The main advantage of the proposed composite is that it has a low density, below the relative resin, about 1.06 kg / m³ for the PG. The composite showed a mechanical behavior less than of the resin to the grain sizes and for all formulations studied. Showed better results for the bending, reaching 25.3 MPa for the PG. The composite also showed be feasible for thermal applications, with thermal conductivity less than 0.21 W / m, ranking as insulation. In terms of homogeneity of the mixture, the most viable grain size is the PF, which also showed improved aesthetics and better processability. This composite can be used to make structures that do not require significant mechanical strength, such as tables, chairs, planks, and solar and wind prototypes, such as ovens and cookers and turbines blades.

Obtenção e caracterização de um compósito de matriz polimérica com carga de resíduos vegetal proveniente do sabugo de milho

The feasibility of using the corn cob to obtain a polymer matrix composite was studied. To obtain the bran, corncob passed the drying process in a solar dryer, and was subsequently triturated in forage and to obtain the different particle sizes, by sieving. Three different grain sizes were used: fine particles (FP) size between 0,10 and 2mm; sized particles (PM) with sizes between 2,10 and 3,35 mm; large particles (PG) sizes between 3,45 and 4,10 mm. Using 20% of residue relative to the resin, the test samples were constructed for characterization of the composite, taking into account thermal and mechanical parameters. The main advantage of the proposed composite is that it has a low density, below the relative resin, about 1.06 kg / m³ for the PG. The composite showed a mechanical behavior less than of the resin to the grain sizes and for all formulations studied. Showed better results for the bending, reaching 25.3 MPa for the PG. The composite also showed be feasible for thermal applications, with thermal conductivity less than 0.21 W / m, ranking as insulation. In terms of homogeneity of the mixture, the most viable grain size is the PF, which also showed improved aesthetics and better processability. This composite can be used to make structures that do not require significant mechanical strength, such as tables, chairs, planks, and solar and wind prototypes, such as ovens and cookers and turbines blades.

Obtenção e caracterização de um compósito de matriz polimérica com carga de bucha vegetal luffa cylindrica

Composite materials arise from the need for lighter materials and with bigger mechanical and thermal resistance. The difficulties of discard, recycling or reuse are currently environmental concerns and, therefore, they are study object of much researches. In this perspective the feasibility of using loofahs (Luffa Cylindrica) for obtainment of a polymeric matrix composite was studied. Six formulations, with 4, 5 and 6 treated layers and untreated, were tested. The loofahs were treated in boiling water to remove lignins, waxes and impurities present in the fibers. After that, they were dried in a direct exposure solar dryer. For the characterization of the composite, thermal (thermal conductivity, thermal capacity, thermal diffusivity and thermal resistivity), mechanical (tensile and bending resistance) and physicochemical (SEM, XRD, density, absorption and degradation) properties were determined. The proposed composite has as advantage the low fiber density, which is around 0.66 g/cm³ (almost half of the polyester resin matrix), resulting in an average composite density of around 1.17g/cm³, 6.0 % lower in relation to the matrix. The treatment carried out in the loofahs increased the mechanical strength of the composite and decreased the humidity absorption. The composite showed lower mechanical behavior than the matrix for all the formulations. The composite also demonstrated itself to be feasible for thermal applications, with a value of thermal conductivity of less than 0.159 W/m.K, ranking it as a good thermal insulator. For all formulations/settings a low adherence between fibers and matrix occurred, with the presence of cracks, showing the fragility due to low impregnation of the fiber by the matrix. This composite can be used to manufacture structures that do not require significant mechanical strength, such as solar prototypes, as ovens and stoves.