967 resultados para Nuclear saline water conversion plants.


Relevância:

100.00% 100.00%

Publicador:

Resumo:

A distinctive feature of the Nhecolandia, a sub-region of the Pantanal wetland in Brazil, is the presence of both saline and freshwater lakes. Saline lakes used to be attributed to a past and phase during the Pleistocene. However, recent studies have shown that saline and fresh water lakes are linked by a continuous water table, indicating that saline water could come from a contemporary concentration process. This concentration process could also be responsible for the large chemical variability of the waters observed in the area. A regional water sampling has been conducted in surface and sub-surface water and the water table, and the results of the geochemical and statistical analysis are presented. Based on sodium contents, the concentration shows a 1: 4443 ratio. All the samples belong to the same chemical family and evolve in a sodic alkaline manner. Calcite or magnesian calcite precipitates very early in the process of concentration, probably followed by the precipitation of magnesian silicates. The most concentrated solutions remain under-saturated with respect to the sodium carbonate salt, even if this equilibrium is likely reached around the saline lakes. Apparently, significant amounts of sulfate and chloride are lost simultaneously from the solutions, and this cannot be explained solely by evaporative concentration. This could be attributed to the sorption on reduced minerals in a green sub-surface horizon in the "cordilhieira" areas. In the saline lakes, low potassium, phosphate, magnesium, and sulfate are attributed to algal blooms. Under the influence of evaporation, the concentration of solutions and associated chemical precipitations are identified as the main factors responsible for the geochemical variability in this environment (about 92 % of the variance). Therefore, the saline lakes of Nhecolandia have to be managed as landscape units in equilibrium with the present water flows and not inherited from a past and phase. In order to elaborate hydrochemical tracers for a quantitative estimation of water flows, three points have to be investigated more precisely: (1) the quantification of magnesium involved in the Mg-calcite precipitation; (2) the identification of the precise stoichiometry of the Mg-silicate; and (3) the verification of the loss of chloride and sulfate by sorption onto labile iron minerals.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Reverse osmosis (RO) membranes have been used extensively in water desalination plants, waste water treatment in industries, agricultural farms and drinking water production applications. The objective of this work is to impart antibacterial and antifungal activities to commercially available RO membrane used in water purification systems by incorporating biogenic silver nanoparticles (AgNPs) synthesized using Rosa indica wichuriana hybrid leaf extract. The morphology and surface topography of uncoated and AgNPs-coated RO membrane were studied using Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Elemental composition of the AgNPs-coated RO membrane was analyzed by energy-dispersive X-ray spectroscopy (EDAX). The functional groups were identified by Fourier Transform Infrared spectroscopy (FT-IR). Hydrophilicity of the uncoated and AgNPs-coated RO membrane was analyzed using water contact angle measurements. The thermal properties were studied by thermogravimetric analysis (TGA). The AgNPs incorporated RO membrane exhibited good antibacterial and antifungal activities against pathogenic bacterial strains such as E. coli, S. aureus, M. luteus, K. pneumoniae, and P. aeruginosa and fungal strains such as Candida tropicalis, C. krusei, C. glabrata, and C. albicans.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Because the Stuart area is, at times, surrounded on three sides by saline water, the underlying fresh-water aquifer is vulnerable to salt-water encroachment. With progressively larger withdrawals of ground water for public and private supplies, the possibility of salt-water contamination of freshwater supplies is increased. (PDF contains 51 pages.)

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The direct measurement of in situ respiring bacteria using 5-cyano-2,3-ditolyl tetrazolium chloride (CTC) shows that, especially for Gram-negative bacteria, large numbers of viable but non-culturable (VBNC) bacteria are present in finished water from a conventional water treatment plant, and the regrowth of bacteria along distribution networks can be seen rapidly by using this very sensitive technique. The level of bacterial inactivation with chlorine is much less important than has been previously supposed (based on experiments with non-injured laboratory strains of bacteria and classical culture techniques). Threshold values of VBNC bacteria leaving water treatment plants or regrowing along distribution systems have to be determined for better control of coliform regrowth and health- risks associated with the consumption of drinking water.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

A study was conducted to investigate the survival of five Pseudomonas strains resistant to antibiotics in different types of water. The selected Pseudomonas strains were designated as strain P1 (CT-29), strain P2 (CT-25), strain P3 (CT-36), strain P4 (CT-20) and strain P5 (CT-27) which were only recovered from farmed fishes. Six types of water viz., distilled water, saline water, tap water, deionized water, pond water and river water were used. Among these experimental waters, river water was found to be the most suitable for long-term survival of these strains. Deionized water did not support survival of all these Pseudomonas strains. Pond water, tap water and distilled water were moderately suitable for strain P1 and strain P4. Saline water was also found to be highly suitable for long-term survival in case of the strain P3 and moderately suitable for normal survival of strain P2 and strain P5.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The characteristic of biodiesel fuel production from transesterification of soybean oil is studied. The reactant solution is the mixture of soybean oil, methanol, and solvent. A new lipase immobilization method, textile cloth immobilization, was developed in this study. Immobilized Candida lipase sp. 99-125 was applied as the enzyme catalyst. The effect of flow rate of reaction liquid, solvents, reaction time, and water content on the biodiesel yield is investigated. Products analysis shows that the main components in biodiesel are methyl sterate, methyl hexadecanoate, methyl oleate, methyl linoleate, and methyl linolenate. The test results indicate that the maximum yield of biodiesel of 92% was obtained at the conditions of hexane being the solvent, water content being 20 wt%, and reaction time being 24 h.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

A proactive risk management strategy seeks to prevent accidents from taking place and maintain the safety of a system. In this context, the task of identifying and disseminating early warning signs and signals is among the most important. The problem is that warning signs that are present before an accident takes place are often being overlooked and not picked up or identified as warning signs. If these warning signs were responded to, then an accident may be averted. Accidents occuring in the critical domain of a drinking water treatments works can have serious implications for the public health of consumers of the water supplied. Realising and comprehending early warning signs is a major challenge for the domain of systems safety and especially in the domain of a water treatment works. The approaches that are typically used to enhance the realisation, comprehension and dissemination of early warning signs in the water treatment domain in Ireland mainly involves the creation of accident scenarios, the use of monitoring data and procedures for the dissemination of warnings. While all of these approaches are all useful to inform the mental or process models of possible accident scenarios, nevertheless, accidents are still occurring in this domain. Therefore, a new approach to enhance the comprehension of and effective dissemination of early warning signs is required in order to improve safety and proactive risk management strategies. The contributions of this thesis is the provision of a set of attributes associated with the early warning sign concept that provides meaningful data on the early warning signs and allows recipients to better comprehend them. The values of these attributes were customised for application in the water treatment domain. This research proves that early warning signs at a water treatment works received with information on their attributes are comprehended and communicated more effectively and efficiently than the usual pragmatic approach and thereby improves the safety and proactive risk management strategies.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The valuation of ecosystem services such as drinking water provision is of growing national and international interest. The cost of drinking water provision is directly linked to the quality of its raw water input, which is itself affected by upstream land use patterns. This analysis employs the benefit transfer method to quantify the economic benefits of water quality improvements for drinking water production in the Neuse River Basin in North Carolina. Two benefit transfer approaches, value transfer and function transfer, are implemented by combining the results of four previously published studies with data collected from eight Neuse Basin water treatment plants. The mean net present value of the cost reduction estimates for the entire Neuse Basin ranged from $2.7 million to $16.6 million for a 30% improvement in water quality over a 30-year period. The value-transfer approach tended to produce larger expected benefits than the function-transfer approach, but both approaches produced similar results despite the differences in their methodologies, time frames, study sites, and assumptions. © 2010 ASCE.

Relevância:

100.00% 100.00%

Publicador:

Relevância:

100.00% 100.00%

Publicador:

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Monitoring of coastal and estuarine water quality has been traditionally performed by sampling with subsequent laboratory analysis. This has the disadvantages of low spatial and temporal resolution and high cost. In the last decades two alternative techniques have emerged to overcome this drawback: profiling and remote sensing. Profiling using multi-parameter sensors is now in a commercial stage. It can be used, tied to a boat, to obtain a quick “picture” of the system. The spatial resolution thus increases from single points to a line coincident with the boat track. The temporal resolution however remains unchanged since campaigns and resources involved are basically the same. The need for laboratory analysis was reduced but not eliminated because parameters like nutrients, microbiology or metals are still difficult to obtain with sensors and validation measurements are still needed. In the last years the improvement in satellite resolution has enabled its use for coastal and estuarine water monitoring. Although spatial coverage and resolution of satellite images in the present is already suitable to coastal and estuarine monitoring, temporal resolution is naturally limited to satellite passages and cloud cover. With this panorama the best approach to water monitoring is to integrate and combine data from all these sources. The natural tools to perform this integration are numerical models. Models benefit from the different sources of data to obtain a better calibration. After calibration they can be used to extend spatially and temporally the methods resolution. In Algarve (South of Portugal) a monitoring effort using this approach is being undertaken. The monitoring effort comprises five different locations including coastal waters, estuaries and coastal lagoons. The objective is to establish the base line situation to evaluate the impact of Waste Water Treatment Plants design and retrofitting. The field campaigns include monthly synoptic profiling, using an YSI 6600 multi-parameter system, laboratory analysis and fixed stations. The remote sensing uses ENVISAT\MERIS Level 2 Full Resolution data. This data is combined and used with the MOHID modelling system to obtain an integrate description of the systems. The results show the limitations of each method and the ability of the modelling system to integrate the results and to produce a comprehensive picture of the system.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Thesis (Ph.D.)--University of Washington, 2014

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Dissertação para a obtenção do grau de doutor em Biologia pelo Instituto de Tecnologia Química e Biológica. Universidade Nova de Lisboa

Relevância:

100.00% 100.00%

Publicador:

Resumo:

La demande croissante en carburants, ainsi que les changements climatiques dus au réchauffement planétaire poussent le monde entier à chercher des sources d’énergie capables de produire des combustibles alternatifs aux combustibles fossiles. Durant les dernières années, plusieurs sources potentielles ont été identifiées, les premières à être considérées sont les plantes oléagineuses comme source de biocarburant, cependant l’utilisation de végétaux ou d’huiles végétales ayant un lien avec l’alimentation humaine peut engendrer une hausse des prix des denrées alimentaires, sans oublier les questions éthiques qui s’imposent. De plus, l'usage des huiles non comestibles comme sources de biocarburants, comme l’huile de jatropha, de graines de tabac ou de jojoba, révèle un problème de manque de terre arable ce qui oblige à réduire les terres cultivables de l'industrie agricole et alimentaire au profit des cultures non comestibles. Dans ce contexte, l'utilisation de microorganismes aquatiques, tels que les microalgues comme substrats pour la production de biocarburant semble être une meilleure solution. Les microalgues sont faciles à cultiver et peuvent croitre avec peu ou pas d'entretien. Elles peuvent ainsi se développer dans des eaux douces, saumâtres ou salées de même que dans les terres non cultivables. Le rendement en lipide peut être largement supérieur aux autres sources de biocarburant potentiel, sans oublier qu’elles ne sont pas comestibles et sans aucun impact sur l'industrie alimentaire. De plus, la culture intensive de microalgues pour la production de biodiesel pourrait également jouer un rôle important dans l'atténuation des émissions de CO2. Dans le cache de ce travail, nous avons isolé et identifié morphologiquement des espèces de microalgues natives du Québec, pour ensuite examiner et mesurer leur potentiel de production de lipides (biodiesel). L’échantillonnage fut réalisé dans trois régions différentes du Québec: la région de Montréal, la gaspésie et le nord du Québec, et dans des eaux douces, saumâtres ou salées. Cent souches ont été isolées à partir de la région de Montréal, caractérisées et sélectionnées selon la teneur en lipides et leur élimination des nutriments dans les eaux usées à des températures différentes (10 ± 2°C et 22 ± 2°C). Les espèces ayant une production potentiellement élevée en lipides ont été sélectionnées. L’utilisation des eaux usées, comme milieu de culture, diminue le coût de production du biocarburant et sert en même temps d'outil pour le traitement des eaux usées. Nous avons comparé la biomasse et le rendement en lipides des souches cultivées dans une eau usée par apport à ceux dans un milieu synthétique, pour finalement identifié un certain nombre d'isolats ayant montré une bonne croissance à 10°C, voir une teneur élevée en lipides (allant de 20% à 45% du poids sec) ou une grande capacité d'élimination de nutriment (>97% d'élimination). De plus, nous avons caractérisé l'une des souches intéressantes ayant montré une production en lipides et une biomasse élevée, soit la microalgue Chlorella sp. PCH90. Isolée au Québec, sa phylogénie moléculaire a été établie et les études sur la production de lipides en fonction de la concentration initiale de nitrate, phosphate et chlorure de sodium ont été réalisées en utilisant de la méthodologie des surfaces de réponse. Dans les conditions appropriées, cette microalgue pourrait produire jusqu'à 36% de lipides et croitre à la fois dans un milieu synthétique et un milieu issu d'un flux secondaire de traitement des eaux usées, et cela à 22°C ou 10°C. Ainsi, on peut conclure que cette souche est prometteuse pour poursuivre le développement en tant que productrice potentielle de biocarburants dans des conditions climatiques locales.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Soil moisture plays a cardinal role in sustaining eclological balance and agricultural development – virtually the very existence of life on earth. Because of the growing shortage of water resources, we have to use the available water most efficiently by proper management. Better utilization of rainfall or irrigation management depends largely on the water retention characteristics of the soil.Soil water retention is essential to life and it provides an ongoing supply of water to plants between periods of irrigation so as to allow their continued growth and survival.It is essential to maintain readily available water in the soil if crops are to sustain satisfactory growth. The plant growth may be retarded if the soil moisture is either deficient or excessive. The optimum moisture content is that moisture which leads to optimum growth of plant. When watering is done, the amount of water supplied should be such that the water content is equal to the field capacity that is the water remained in the saturated soil after gravitational drainage. Water will gradually be utilized consumptively by plants after the water application, and the soil moisture will start falling. When the water content in the soil reaches the value known as permanent wilting point (when the plant starts wilting) fresh dose of irrigation may be done so that water content is again raised to the field capacity of soil.Soil differ themselves in some or all the properties depending on the difference in the geotechnical and environmental factors. Soils serve as a reservoir of the nutrients and water required for crops.Study of soil and its water holding capacity is essential for the efficient utilization of irrigation water. Hence the identification of the geotechnical parameters which influence the water retention capacity, chemical properties which influence the nutrients and the method to improve these properties have vital importance in irrigation / agricultural engineering. An attempt in this direction has been made in this study by conducting the required tests on different types of soil samples collected from various locations in Trivandrum district Kerala, with and without admixtures like coir pith, coir pith compost and vermi compost. Evaluation of the results are presented and a design procedure has been proposed for a better irrigation scheduling and management.