927 resultados para Non-ionic surfactant. Cloud point. Flory-Huggins model. UNIQUAC model. NRTL model
Resumo:
Quantification of the effects of adjuvants on droplet behaviour on plant surfaces is needed to improve pesticide spray application efficiency for soybeans. Dispersion and evaporation of single 300-μm diameter droplets amended with each of four spray adjuvants at five concentrations were investigated for four soybean plant surfaces (abaxial and adaxial leaflet surfaces, petiole, basal stem). The four adjuvants were a crop oil concentrate (COC), a modified seed oil (MSO), a non-ionic surfactant (NIS) and an oil surfactant blend (OSB). A single-droplet generator was used to produce and deposit 300-μm diameter droplets on target surfaces under controlled environmental conditions. Adjuvants significantly increased the dispersion (or wetted area) of droplets on plant surfaces. Droplet-wetted areas increased with increased adjuvant concentrations but not in direct proportion. The average increases of wetted areas across the four soybean plant surfaces were 443, 462, 416, or 343% when the spray mixture was amended with COC, MSO, NIS or OSB at the manufacturer-recommended concentrations, respectively. Among the four surfaces, the largest wetted area was on the abaxial surface, followed by the adaxial surface, the petiole and then the basal stem. Droplet evaporation times were inversely proportional to the wetted areas. The evaporation time of 300-μm diameter droplets ranged from 36 to 142. s on the four surfaces when the spray mixture was amended with an adjuvant, whereas the water-only droplets ranged from 161 to 190. s. The results demonstrated that use of adjuvants offers great potential to improve the homogeneity of sprayed pesticides, to increase spray coverage and to reduce pesticide application rates on soybean plants. These effects could benefit farmers economically and reduce environmental contamination by pesticides. © 2012.
Resumo:
Die vorliegende Dissertation untersucht Nanopartikel und Nanokapseln aus verschiedenen Materialien mit verschiedenen Modifikationen für einen zielgerichteten Medikamententransport (Drug Targeting). Obwohl bisher zahlreiche Nanopartikel und -kapseln synthetisiert wurden, besteht nach wie vor hinsichtlich der zellulären Verträglichkeit, Biokompatibilität und Aufnahme kein allumfassendes Verständnis. Mit Hilfe der in dieser Arbeit vorgestellten Untersuchungen und Ergebnissen soll ein Beitrag zur Schließung dieser Lücke geleistet werden.rnIm Rahmen der vorliegenden Dissertation wurde der Einfluss der Herstellungsmaterialien PS, PLLA, PMMA, Biomakromoleküle (BSA, DNA), ggf. stabilisiert durch HPMA-LMA-Copolymere und neu-synthetisierte Surfmere, der Formmodifikationen Streckung und Kristallisierung, der Oberflächenmodifikationen mittels verschiedener Tenside und PEG auf die zelluläre Aufnahme und Verträglichkeit hin untersucht.rnZusammenfassend lässt sich die Aussage treffen, dass zahlreiche Materialien zur Herstellung von Trägersystemen geeignet sind und sich als biokompatibel und nicht-zytotoxisch erwiesen haben, sich jedoch stark hinsichtlich der Aufnahmeeffizienz in verschiedene Zelllinien unterscheiden. rnIm ersten Abschnitt (Kapitel 5.1) wurden in der ersten und zweiten Untersuchung auf allgemeine Parameter, die die Aufnahme von Nanopartikeln beeinflussen, eingegangen. Hier wurde der Einfluss des Alters von PLLA-Partikeln auf die zelluläre Aufnahme und Toxizität untersucht. Es konnte gezeigt werden, dass mit zunehmender Materialalterung die zelluläre Aufnahme abnimmt. Eine Zytotoxizität konnte nicht gezeigt werden.rnWeiterhin wurde der Einfluss des FCS-Gehalts des Zell-Mediums auf die zelluläre Aufnahme von PMMA-Partikeln untersucht. Es konnte gezeigt werden, dass mit einer steigenden FCS-Konzentration eine Abnahme der zellulären Aufnahme von PMMA-Partikeln einhergeht. Die höchste zelluläre Aufnahme konnte bei einem FCS-Gehalt des Zellmediums von 0,05% verzeichnet werden. rnIm zweiten Abschnitt (Kapitel 5.2) wurde die Stabilisierung von Nanopartikeln mittels neusynthetisierter Tenside und deren Einfluss auf die Zelle-Nanopartikel-Interaktionen untersucht. Dazu wurde zum einen die Oberflächenfunktionalisierung von Nanopartikeln mit Hilfe neu-synthetisierter „Surfmere“ und deren Einfluss auf die zelluläre Aufnahme und Toxizität untersucht. Die hergestellten Surfmere bewirken gleichzeitig eine Stabilisierung und Funktionalisierung der Nanopartikeloberfläche mit Phosphonatgruppen. Hier wurden kovalente „Surfmer“ stabilisierte Nanopartikel mit Tensid- (SDP) stabilisierten Nanopartikeln verglichen. Zudem wurden dialysierte Nanopartikel mit nicht-dialysierten verglichen. Bezüglich der zellulären Aufnahme konnte für die mittels Dialyse gereinigten Nanopartikel eine gute Aufnahme ohne Unterschiede zwischen den kovalent und nicht-kovalent Phosphonat-funktionalisierten Partikeln beobachtet werden. Die ungereinigten, SDP-stabilisierte, nicht-kovalent gebundene Nanopartikel zeigten hingegen eine bis zu 30% stärkere Aufnahme in die HeLa-Zellen und hMSCs.rnWeiterhin der Einsatz von mit HPMA-LMA-Copolymeren stabilisierte Polystyrol- und PLLA-Partikel, die den Einsatz von Tensiden während des Miniemulsionsprozesses überflüssig machen, untersucht. Auch hier konnte keine Zytotoxizität nachgewiesen werden. Die Aufnahme in HeLa-Zellen scheint mehr von der Größe der Nanopartikel als vom verwendeten Material und in hMSCs mehr von den Oberflächeneigenschaften der Nanopartikel abzuhängen.rnIm dritten Abschnitt (Kapitel 5.3) wird auf die Möglichkeit der Formmodifikation von Polystyrol-Partikeln und deren Einfluss auf die Nanopartikel-Zelle-Interaktionen eingegangen. Es geht dabei um die Aufnahme und Zytotoxizität von verstreckten (elongierten) Polystyrol-Partikeln im Vergleich zu sphärischen Nanopartikeln, sowie die Aufnahme und Zytotoxizität von kristallinen Polystyrol-Partikeln in verschiedene Zelllinien. Bei den verstreckten Partikeln nimmt die Aufnahme-Effizienz in HeLa-Zellen und hMSCs mit zunehmender Verstreckung ab. Eine Zytotoxizität konnte für keinen der erwähnten Nanopartikel nachgewiesen werden. Bei den Polystyrol-Partikeln unterschiedlicher Taktizität zeigen die kristallierten Polystyrol-Partikel eine geringfügig besser Aufnahme-Rate als die nicht-kristallierten Polystyrol-Partikel. Dabei zeigen die nach dem Herstellungsprozess mittels der Lösemittelverdampfungstechnik der wässrigen Phase entnommenen Partikel eine bessere Aufnahme als die nach der Verdampfung des Chloroforms verfügbaren Partikel. Insgesamt konnte jedoch für alle Polystyrol-Partikel trotz der unterschiedlichen Taktizitäten nach der Aufnahme in HeLa-Zellen und hMSCs mittels Durchflusszytometrie hohe Fluoreszenz-Intensitäten verzeichnet werden. Setzt man hohe Fluoreszenz-Intensitäten bei in Zellen aufgenommenen Partikeln mit guten Aufnahmeraten gleich, sind die hier dargestellten Aufnahmeraten als sehr gut zu bezeichnen. rnAuf Nanosysteme mit einer reduzierten zellulären Aufnahme wird im letzten Abschnitt (Kapitel 5.4) eingegangen. Dabei wird zum einen die unterschiedliche Oberflächenmodifikation von Polystyrol-Partikeln mit dem Co-Monomer PEG-MA und den Tensiden SDS und Lutensol AT50 untersucht. Von PEG-MA wurden zudem verschiedene Molekulargewichte (Mn=300 g•mol-1 und Mn=2080 g•mol-1) und verschiedene Konzentrationen (1,5%, 5%, 10%) eingesetzt. Ein Teil der Partikel wurde mit SDS und der andere Teil mit Lutensol AT50 hergestellt. In einem weiteren Schritt wurde das jeweilig gegenteilige Tensid (statt SDS Lutensol AT50 und umgekehrt) eingesetzt, um zu überprüfen, ob sich der zuvor beobachtete Effekt umkehren lässt. Anschließend wurde ein erst mit SDS stabilisierter Nanopartikel (BR01) mit verschiedenen Lutensol AT50-Anteilen (5%, 10%, 25%, 50%, 100%) redispergiert. Die effizienteste Aufnahme zeigte der unmodifizierte, mit SDS stabilisierte Nanopartikel BR01, die niedrigste der ebenfalls unmodifizierte, mit Lutensol AT50 stabilisierte Nanopartikel BR02. Eine steigende Konzentration des PEG-MA Mn=300 g•mol-1 hemmt die Aufnahme von mit SDS stabilisierten Partikeln konstant. Für PEG-MA Mn=2080 g•mol-1 konnte hingegen kein Einfluss nachgewiesen werden. Für die mit Lutensol AT50 stabilisierten Partikel konnte kein Einfluss von PEG-MA nachgewiesen werden. Daraus resultiert, dass der Einsatz von physikalisch adsorbiertem Lutensol AT50 die zelluläre Aufnahme effektiver hemmt als der Einsatz von kovalent gebundenem PEG-MA unterschiedlicher Kettenlänge.rnDer Einsatz von mit Biomakromolekülen hergestellten Nanokapseln, die mit zwei verschiedenen Tensiden (SDS und Lutensol AT50) stabilisiert wurden, wurde im Weiteren näher untersucht. Bei den mit SDS stabilisierten Kapseln erwiesen sich die mit ssDNA hergestellten Kapseln BN-54 und BN-55 als leicht toxisch für die HeLa-Zellen. Dagegen sind alle eingesetzten, mit Lutensol AT50 redispergierten Nanokapseln sowohl für HeLa-Zellen als auch für hMSCs zytotoxisch. Hier ist die toxische Wirkung auf das nicht-ionische Tensid Lutensol AT50 zurückzuführen. Eine zelluläre Aufnahme konnte für keine mit Biomakromolekülen hergestellten Nanokapsel nachgewiesen werden.rnDen Abschluss der Untersuchungen bildet die vergleichende Analyse der in dieser Arbeit mit dem Fluoreszenzfarbstoff PMI versehenen Partikeln hinsichtlich deren Aufnahme in HeLa-Zellen und hMSCs und deren zytotoxische Auswirkungen. In der vergleichenden Analyse werden die zuvor vorgestellten Ergebnisse für PMI-Partikeln nochmal im Kontext betrachtet. Dabei erwies sich sowohl für die HeLa-Zellen als auch für die hMSCs, dass die meisten Partikel eine geringe bis keine zelluläre Aufnahme zeigen. Eine gute Aufnahme konnte nur für wenige Nanopartikel (vor allem für die kristallinen Nanopartikel) verzeichnet werden. Eine Korrelation zwischen der Aufnahmeeffizienz und der Zytotoxizität konnte nicht nachgewiesen werden. rn
Resumo:
This thesis illustrates the development of tailor-made, partially hydrated skin adhesive hydrogels as a vehicle for the topical delivery of moisturising agents. Maintaining an optimum hydration level of the stratum corneum ensures that the barrier properties of the skin are preserved. An unsaturated ionic monomer 2-acrylamido-2-methylpropanesulfonic acid sodium salt, glycerol, water, a photoinitiator Irgacure 184 and crosslinker Ebacryl II facilitated the production of monophasic sheet skin adhesives using photopolymerisation. The exploration and modification of the hydrogel components coupled with their influence on the adhesive and dynamic mechanical behaviour led to the development of novel monophasic and biphasic hydrogels. Biphasic pregels comprising of a hydrophobic monomer (epoxidised soybean oil acrylate, lauryl acrylate or stearyl acrylate) micellised with a non ionic surfactant Tween 60 allowed a homogeneous distribution throughout a predominantly hydrophilic phase (2-acrylamido-2-methylpropanesulfonic acid sodium salt, 4-acryloylmorpholine, glycerol and water). Further development of biphasic hydrogel technology led to the incorporation of preformed commercial O/W emulsions (Acronal, Flexbond 150, DM137 or Texicryl 13056WB) allowing the hydrophobic component to be added without prior stabilisation. The topical release of moisturising agents 2-pyrrolidone-5-carboxylic acid, lactobionic acid and d-calcium pantothenate results in the deposition onto the skin by an initial burst mechanism. The hydration level of the stratum corneum was measured using a Comeometer CM 825, Skin Reader MY810 or FT-ATR. The use of hydrophilic actives in conjunction with lipophilic agents for example Vitamin E or Jojoba oil provided an occlusive barrier, which reduced the rate of transepidermal water loss. The partition coefficients of the release agents provided invaluable information which enabled the appropriate gel technology to be selected. In summary the synthetic studies led to the understanding and generation of transferable technology. This enabled the synthesis of novel vehicles allowing an array of actives with a range of solubilities to be incorporated.
Resumo:
The preparation of a steam-based hydrothermally stable transition alumina is reported. The gel was derived from a synthetic sol-gel route where Al-tri-sec-butoxide is hydrolysed in the presence of a non-ionic surfactant (EO20PO70EO20), HCl as the catalyst and water (H2O/Al = 6); the condensation was enhanced by treating the hydrolysed gel with tetrabutylammonium hydroxide (TBAOH), after which it was dried at 60 °C by solvent evaporation. The so-obtained mesophase was crystallized under argon at 1200 °C (1 h) producing a transition alumina containing δ/α, and possibly θ, alumina phases. Due to its surface acidity, the pyrolysis conditions transform the block copolymer into a cross-linked char structure that embeds the alumina crystallites. Calcination at 650 °C generates a fully porous material by burning the char; a residual carbon of 0.2 wt.% was found, attributed to the formation of surface (oxy)carbides. As a result, this route produces a transition alumina formed by nanoparticles of about 30 nm in size on average, having surface areas in the range of 59-76 m2 g-1 with well-defined mesopores centered at 14 nm. The material withstands steam at 900 °C with a relative surface area rate loss lower than those reported for δ-aluminas, the state-of-the-art MSU-X γ-alumina and other pure γ-aluminas. The hydrothermal stability was confirmed under relevant CH4 steam reforming conditions after adding Ni; a much lower surface area decay and higher CH4 conversion compared to a state-of-the-art MSU-X based Ni catalyst were observed. Two effects are important in explaining the properties of such an alumina: the char protects the particles against sintering, however, the dominant effect is provided by the TBAOH treatment that makes the mesophase more resistant to coarsening and sintering. This journal is © the Partner Organisations 2014.
Resumo:
Abstract - This study investigates the effect of solid dispersions prepared from of polyethylene glycol (PEG) 3350 and 6000 Da alone or combined with the non-ionic surfactant Tween 80 on the solubility and dissolution rate of a poorly soluble drug eprosartan mesylate (ESM) in attempt to improve its bioavailability following its oral administration.
INTRODUCTION
ESM is a potent anti-hypertension [1]. It has low water solubility and is classified as a Class II drug as per the Biopharmaceutical Classification Systems (BCS) leading to low and variable oral bioavailability (approximately 13%). [2]. Thus, improving ESM solubility and/or dissolution rate would eventually improve the drug bioavailability. Solid dispersion is widely used technique to improve the water solubility of poorly water-soluble drugs employing various biocompatible polymers. In this study, we aimed to enhance the solubility and dissolution of EMS employing solid dispersion (SD) formulated from two grades of poly ethylene glycol (PEG) polymers (i.e. PEG 3350 & PEG 6000 Da) either individually or in combination with Tween 80.
MATERIALS AND METHODS
ESM SDs were prepared by solvent evaporation method using either PEG 3350 or PEG 6000 at various (drug: polymer, w/w) ratios 1:1, 1:2, 1:3, 1:4, 1:5 alone or combined with Tween 80 added at fixed percentage of 0.1 of drug by weight?. Physical mixtures (PMs) of drug and carriers were also prepared at same ratios. Drug solid dispersions and physical mixtures were characterized in terms of drug content, drug dissolution using dissolution apparatus USP II and assayed using HPLC method. Drug dissolution enhancement ratio (ER %) from SD in comparison to the plain drug was calculated. Drug-polymer interactions were evaluated using Differential Scanning Calorimetry (DSC) and FT-IR.
RESULTS AND DISCUSSION
The in vitro solubility and dissolution studies showed SDs prepared using both polymers produced a remarkable improvement (p<0.05) in comparison to the plain drug which reached around 32% (Fig. 1). The dissolution enhancement ratio was polymer type and concentration-dependent. Adding Tween 80 to the SD did not show further dissolution enhancement but reduced the required amount of the polymer to get the same dissolution enhancement. The DSC and FT-IR studies indicated that using SD resulted in transformation of drug from crystalline to amorphous form.
CONCLUSIONS
This study indicated that SDs prepared by using both polymers i.e. PEG 3350 and PEG 6000 improved the in-vitro solubility and dissolution of ESM remarkably which may result in improving the drug bioavailability in vivo.
Acknowledgments
This work is a part of MSc thesis of O.M. Ali at the Faculty of Pharmacy, Aleppo University, Syria.
REFERENCES
[1] Ruilope L, Jager B: Eprosartan for the treatment of hypertension. Expert Opin Pharmacother 2003; 4(1):107-14
[2] Tenero D, Martin D, Wilson B, Jushchyshyn J, Boike S, Lundberg, D, et al. Pharmacokinetics of intravenously and orally administered Eprosartan in healthy males: absolute bioavailability and effect of food. Biopharm Drug Dispos 1998; 19(6): 351- 6.
Resumo:
Natural rubber latex, an aqueous colloidal dispersion of polyisoprene is widely used in production of gloves, catherers, rubber bands etc. The natural rubber latex content present in products such as gloves causes allergic problems. Of the different types of allergies reported, latex is known to produce Type I and Type IV allergies. Type I is called immediate hypersensitivity and type IV is called delayed hypersensitivity. It has been reported that some of the proteins present in the latex are mainly responsible for the allergic reactions type I. Significant reduction in the allergic response (type I) of natural rubber latex can be achieved by the reduction in its protein content, however out of the total proteins present in the latex or latex film only a fraction is extractable. The major techniques employed to reduce protein content of latex include leaching, autoclaving, chlorination, use of proteolytic enzymes and use of non ionic surfactants. Sulphur vulcanization of dipped products is responsible for Type IV allergy. N-nitrosamine, a carcinogenic substance is produced as a result of sulphur vulcanization. Radiation vulcanization can be used as an alternative for sulphur vulcanization. The current research deals with techniques to reduce the allergy associated with latex products. To reduce the type I allergy, low protein latex is developed using polyethylene glycol, a non- ionic surfactant. The present study employs radiation vulcanization to eliminate type IV allergy. The effect of different cure systems and fillers on the properties of low protein latex is also investigated as a part of the study.
Resumo:
The use of surfactants to improve enzymatic hydrolysis of the macroalgae Sargassum muticum has been investigated. Visible absorption spectroscopy has been used to quantify the solubilization of both polysaccharides and phlorotannins in the hydrolysates. After total extraction, results showed that Sargassum muticum contained 2.74% (expressed in percent of the dry weight of the algae) of phlorotannins whose 32 % were in the cell wall. This result shows that it is important to access to the parietal phlorotannins. To reach this objective, we chose the enzymatic approach for destructurating the cell wall of the algae. The use of 5% dry weight (DW - 5% by weight of hydrolyzed algae) of an enzymatic mix containing a commercial beta-glucanase, a commercial protease and an alginate lyase extracted from Pseudomonas alginovora led after 3 hours of hydrolysis to the solubilization of 2.43% DW polysaccharides and 0.52% DW phlorotannins. The use of 0.5% volume of the surfactant Triton® X-100 with 10% DW of the enzymatic mix has allowed to reaching the value of 2.63% DW of solubilized phlorotannins, that is 96% of the total phenolic content. The use of non-ionic surfactant, combined to enzymatic hydrolysis, showed an increased efficiency in disrupting cell wall and solubilizing phlorotannins in Sargassum muticum.
Resumo:
The nonionic surfactants are composed of substances whose molecules in solution, does not ionize. The solubility of these surfactants in water due to the presence of functional groups that have strong affinity for water. When these surfactants are heated is the formation of two liquid phases, evidenced by the phenomenon of turbidity. This study was aimed to determine the experimental temperature and turbidity nonilfenolpoliethoxyled subsequently perform a thermodynamic modeling, considering the models of Flory-Huggins and the empirical solid-liquid equilibrium (SLE). The method used for determining the turbidity point was the visual method (Inoue et al., 2008). The experimental methodology consisted of preparing synthetic solutions of 0,25%, 0,5%, 1%, 2%, 3%, 4%, 5%, 6%, 7%, 8%, 9%, 10%, 12,5%, 15%, 17% and 20% by weight of surfactant. The nonionic surfactants used according to their degree of ethoxylation (9.5, 10, 11, 12 and 13). During the experiments the solutions were homogenized and the bath temperature was gradually increased while the turbidity of the solution temperature was checked visually Inoue et al. (2003). These temperature data of turbidity were used to feed the models evaluated and obtain thermodynamic parameters for systems of surfactants nonilfenolpoliethoxyled. Then the models can be used in phase separation processes, facilitating the extraction of organic solvents, therefore serve as quantitative and qualitative parameters. It was observed that the solidliquid equilibrium model (ESL) was best represented the experimental data.
Resumo:
Flory-Huggins interaction parameters and thermal diffusion coefficients were measured for aqueous biopolymer solutions. Dextran (a water soluble polysaccharide) and bovine serum albumin (BSA, a water soluble protein) were used for this study. The former polymer is representative for chain macromolecules and the latter is for globular macromolecules. The interaction parameters for the systems water/dextran and water/BSA were determined as a function of composition by means of vapor pressure measurements, using a combination of headspace sampling and gas chromatography (HS-GC). A new theoretical approach, accounting for chain connectivity and conformational variability, describes the observed dependencies quantitatively for the system water/dextran and qualitatively for the system water/BSA. The phase diagrams of the ternary systems water/methanol/dextran and water/dextran/BSA were determined via cloud point measurements and modeled by means of the direct minimization of the Gibbs energy using the information on the binary subsystems as input parameters. The thermal diffusion of dextran was studied for aqueous solutions in the temperature range 15 < T < 55 oC. The effects of the addition of urea were also studied. In the absence of urea, the Soret coefficient ST changes its sign as T is varied; it is positive for T > 45.0 oC, but negative for T < 45.0 oC. The positive sign of ST means that the dextran molecules migrate towards the cold side of the fluid; this behavior is typical for polymer solutions. While a negative sign indicates the macromolecules move toward the hot side; this behavior has so far not been observed with any other binary aqueous polymer solutions. The addition of urea to the aqueous solution of dextran increases ST and reduces the inversion temperature. For 2 M urea, the change in the sign of ST is observed at T = 29.7 oC. At higher temperature ST is always positive in the studied temperature range. To rationalize these observations it is assumed that the addition of urea opens hydrogen bonds, similar to that induced by an increase in temperature. For a future extension of the thermodynamic studies to the effects of poly-dispersity, dextran was fractionated by means of a recently developed technique called Continuous Spin Fractionation (CSF). The solvent/precipitant/polymer system used for the thermodynamic studies served as the basis for the fractionation of dextran The starting polymer had a weight average molar mass Mw = 11.1 kg/mol and a molecular non-uniformity U= Mw / Mn -1= 1.0. Seventy grams of dextran were fractionated using water as the solvent and methanol as the precipitant. Five fractionation steps yielded four samples with Mw values between 4.36 and 18.2 kg/mol and U values ranging from 0.28 to 0.48.
Resumo:
The use of non-heart-beating donor (NHBD) lungs may help to overcome the shortage of lung grafts in clinical lung transplantation, but warm ischaemia and ischaemia/reperfusion injury (I/R injury) resulting in primary graft dysfunction represent a considerable threat. Thus, better strategies for optimized preservation of lung grafts are urgently needed. Surfactant dysfunction has been shown to contribute to I/R injury, and surfactant replacement therapy is effective in enhancing lung function and structural integrity in related rat models. In the present study we hypothesize that surfactant replacement therapy reduces oedema formation in a pig model of NHBD lung transplantation. Oedema formation was quantified with (SF) and without (non-SF) surfactant replacement therapy in interstitial and alveolar compartments by means of design-based stereology in NHBD lungs 7 h after cardiac arrest, reperfusion and transplantation. A sham-operated group served as control. In both NHBD groups, nearly all animals died within the first hours after transplantation due to right heart failure. Both SF and non-SF developed an interstitial oedema of similar degree, as shown by an increase in septal wall volume and arithmetic mean thickness as well as an increase in the volume of peribron-chovascular connective tissue. Regarding intra-alveolar oedema, no statistically significant difference could be found between SF and non-SF. In conclusion, surfactant replacement therapy cannot prevent poor outcome after prolonged warm ischaemia of 7 h in this model. While the beneficial effects of surfactant replacement therapy have been observed in several experimental and clinical studies related to heart-beating donor lungs and cold ischaemia, it is unlikely that surfactant replacement therapy will overcome the shortage of organs in the context of prolonged warm ischaemia, for example, 7 h. Moreover, our data demonstrate that right heart function and dysfunctions of the pulmonary vascular bed are limiting factors that need to be addressed in NHBD.
Resumo:
This work is the first attempt to apply aqueous two-phase mixed micellar systems (ATPMS) of the nonionic surfactant Triton X-114 and the anionic one AOT to extract clavulanic acid (CA) from broth fermented by Streptomyces clavuligerus. Cloud points were determined in McIlvane buffer pH 6.5 with or without NaCl, and diagram phases/coexistence curves were constructed. CA partition was investigated following a 2(4)-full factorial design in which AOT (0.022, 0.033 and 0.044% w/w), Triton X-114 (1.0, 3.0 and 5.0% w/w) and NaCl (0, 2.85 and 5.70% w/w) concentrations and temperature (24,26 and 28 degrees C) were selected as independent variables, and CA partition coefficient (K(CA)) and yield in the top phase (eta(CA)) as responses. CA partitioned always to the top, micelle-poor phase. The regression analysis pointed out that NaCl concentration and interaction between temperature and Triton X-114 concentration had statistically significant effects on K(CA), while eta(CA) was mainly influenced by temperature, Triton X-114 concentration and their interaction. Different ATPMS compositions were then needed to maximize these responses, specifically 0.022% (w/w) AOT, 5% (w/w) Triton X-114 for K(CA) (2.08), and 0.044% (w/w) AOT, 1% (w/w) Triton X-114 for eta(CA) (98.7%), both at 24 degrees C without NaCl. Since at 0.022% (w/w) AOT, 1% (w/w) Triton X-114 and 28 degrees C without NaCl the system was able to ensure satisfactory intermediate results (K(CA) = 1.48; eta(CA) = 86.3%), these conditions were selected as the best ones. These preliminary results are of concern for possible industrial application, because CA partition to the dilute phase can simplify the subsequent purification protocol. (C) 2011 Elsevier B.V. All rights reserved.
Resumo:
Dissertação apresentada para a obtenção do grau de Doutor em Engenharia Química, especialidade Engenharia da Reacção Química, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia
Resumo:
Direct methanol fuel cell, DMFC, model, mass transport, Maxwell-Stefan, Flory-Huggins, crossover, polymer electrolyte membrane, Nafion
Resumo:
Escherichia coli is commonly involved in infections with a heavy bacterial burden. Piperacillin-tazobactam and carbapenems are among the recommended empirical treatments for health care-associated complicated intra-abdominal infections. In contrast to amoxicillin-clavulanate, both have reduced in vitro activity in the presence of high concentrations of extended-spectrum β-lactamase (ESBL)-producing and non-ESBL-producing E. coli bacteria. Our goal was to compare the efficacy of these antimicrobials against different concentrations of two clinical E. coli strains, one an ESBL-producer and the other a non-ESBL-producer, in a murine sepsis model. An experimental sepsis model {~5.5 log10 CFU/g [low inoculum concentration (LI)] or ~7.5 log(10) CFU/g [high inoculum concentration (HI)]} using E. coli strains ATCC 25922 (non-ESBL producer) and Ec1062 (CTX-M-14 producer), which are susceptible to the three antimicrobials, was used. Amoxicillin-clavulanate (50/12.5 mg/kg given intramuscularly [i.m.]), piperacillin-tazobactam (25/3.125 mg/kg given intraperitoneally [i.p.]), and imipenem (30 mg/kg i.m.) were used. Piperacillin-tazobactam and imipenem reduced spleen ATCC 25922 strain concentrations (-2.53 and -2.14 log10 CFU/g [P < 0.05, respectively]) in the HI versus LI groups, while amoxicillin-clavulanate maintained its efficacy (-1.01 log10 CFU/g [no statistically significant difference]). Regarding the Ec1062 strain, the antimicrobials showed lower efficacy in the HI than in the LI groups: -0.73, -1.89, and -1.62 log10 CFU/g (P < 0.05, for piperacillin-tazobactam, imipenem, and amoxicillin-clavulanate, respectively, although imipenem and amoxicillin-clavulanate were more efficacious than piperacillin-tazobactam). An adapted imipenem treatment (based on the time for which the serum drug concentration remained above the MIC obtained with a HI of the ATCC 25922 strain) improved its efficacy to -1.67 log10 CFU/g (P < 0.05). These results suggest that amoxicillin-clavulanate could be an alternative to imipenem treatment of infections caused by ESBL- and non-ESBL-producing E. coli strains in patients with therapeutic failure with piperacillin-tazobactam.
Resumo:
BACKGROUND: Workers with persistent disabilities after orthopaedic trauma may need occupational rehabilitation. Despite various risk profiles for non-return-to-work (non-RTW), there is no available predictive model. Moreover, injured workers may have various origins (immigrant workers), which may either affect their return to work or their eligibility for research purposes. The aim of this study was to develop and validate a predictive model that estimates the likelihood of non-RTW after occupational rehabilitation using predictors which do not rely on the worker's background. METHODS: Prospective cohort study (3177 participants, native (51%) and immigrant workers (49%)) with two samples: a) Development sample with patients from 2004 to 2007 with Full and Reduced Models, b) External validation of the Reduced Model with patients from 2008 to March 2010. We collected patients' data and biopsychosocial complexity with an observer rated interview (INTERMED). Non-RTW was assessed two years after discharge from the rehabilitation. Discrimination was assessed by the area under the receiver operating curve (AUC) and calibration was evaluated with a calibration plot. The model was reduced with random forests. RESULTS: At 2 years, the non-RTW status was known for 2462 patients (77.5% of the total sample). The prevalence of non-RTW was 50%. The full model (36 items) and the reduced model (19 items) had acceptable discrimination performance (AUC 0.75, 95% CI 0.72 to 0.78 and 0.74, 95% CI 0.71 to 0.76, respectively) and good calibration. For the validation model, the discrimination performance was acceptable (AUC 0.73; 95% CI 0.70 to 0.77) and calibration was also adequate. CONCLUSIONS: Non-RTW may be predicted with a simple model constructed with variables independent of the patient's education and language fluency. This model is useful for all kinds of trauma in order to adjust for case mix and it is applicable to vulnerable populations like immigrant workers.