Transient Ventilation Dynamics Following a Change in Strength of a Point Source of Heat

We investigate the transient ventilation flow within a confined ventilated space, with high- and low-level openings, when the strength of a low-level point source of heat is changed instantaneously. The steady-flow regime in the space involves a turbulent buoyant plume, which rises from the point source to a well-mixed warm upper layer. The steady-state height of the interface between this layer and the lower layer of exterior fluid is independent of the heat flux, but the upper layer becomes progressively warmer with heat flux. New analogue laboratory experiments of the transient adjustment between steady states identify that if the heat flux is increased, the continuing plume propagates to the top of the room forming a new, warmer layer. This layer gradually deepens, and as the turbulent plume entrains fluid from the original warm layer, the original layer is gradually depleted and disappears, and a new steady state is established. In contrast, if the source buoyancy flux is decreased, the continuing plume is cooler than the original plume, so that on reaching the interface it is of intermediate density between the original warm layer and the external fluid. The plume supplies a new intermediate layer, which gradually deepens with the continuing flow. In turn, the original upper layer becomes depleted, both as a result of being vented through the upper opening of the space, but also due to some penetrative entrainment of this layer by the plume, as the plume overshoots the interface before falling back to supply the new intermediate layer. We develop quantitative models which are in good accord with our experimental data, by combining classical plume theory with models of the penetrative entrainment for the case of a decrease in heating. Typically, we find that the effect of penetrative entrainment on the density of the intruding layer is relatively weak, provided the change in source strength is sufficiently large. However, penetrative entrainment measurably increases the rate at which the depth of the draining layer decreases. We conclude with a discussion of the importance of these results for the control of naturally ventilated spaces.

Numerical Simulation of Heat Transfer and Kinetics in the Bulk Growth of Silicon Carbide

The growth process of 2-inch silicon carbide (SiC) single crystals by the physical vapor transport method (or modified Lely method) has been modeled and simulated. The comprehensive process model incorporates the calculations of radio frequency (RF) induction heating, heat and mass transfer and growth kinetics. The transport equations for electromagnetic field, heat transfer, and species transport are solved using a finite volume-based numerical scheme called MASTRAPP (Multizone Adaptive Scheme for Transport and Phase Change Process). Temperature distribution for a 2-inch growth system is calculated, and the effects of induction heating frequency and current on the temperature distribution and growth rate are investigated. The predicted results have been compared with the experimental data.

Effect of chloral hydrate on metabolic rate of Labeo rohita (Ham) and Poecilia reticulata (Peters)

Comparative impact of chloral hydrate anaesthesia on the metabolic rate of Indian major carp Labeo rohita and larvivorous fish Poecilia reticulata was assessed. Observation on the Oxygen Consumption Rate (OCR) revealed that in common guppies OCR was substantially low (1.105 and 1.097 mg/g/hr) at 0.1 and 0.25 g/l concentrations of chloral hydrate as against OCR of 1.487 mg/g/hr in the control. Fry of L. rohita in group showed lower metabolic rates in the control as well as treated conditions as compared to the individuals of this fish. This may be due to sympathetic psychophysiological reflex of grouped fish. Higher dose of chloral hydrate (0.25 g/l) also caused higher OCR probably due to distress. Application of chloral hydrate also favoured lesser release of metabolic wastes (ammonia and carbon dioxide). There was significant positive correlation between time and oxygen consumption, whereas, for time and OCR this relationship was negative. Regression of chloral hydrate doses for OCR and time has also been calculated.

The behaviour of laminar stratified methane/air flames in counterflow

Flames propagating through a mixture with a gradient of equivalence ratio have been previously demonstrated to travel faster or slower than their equivalent premixed flames. The present study aims to numerically investigate the response of strained laminar methane-air flames to such gradients. The flames are simulated in a counterflow configuration where a premixed reactant stream at equivalence ratio φR opposes a hot equilibrium stream at equivalence ratio φP. Premixed and stratified flames are compared with respect to the equivalence ratio φ* and the corresponding gradient ∇φ* at the point of peak heat release rate, for three strain rates, a=50, 300 and 500s-1 and a range of φ*. The effect of different stratification levels is also investigated by varying the ratio of φP to φR, Θ. Results indicate that, as long as flames stabilize within the diffusion layer and Θ>1, increased heat release rate Q is seen throughout the progress variable space in comparison to the premixed state. In contrast, an attenuation of heat release rate is seen for Θ<1. The enhancement (or attenuation) of heat release varies monotonically with Θ. The effect of stratification on flame behavior becomes more pronounced as the strain rate increases. The present study reveals the mechanisms for the propagation of quasi-steady stratified flames under lean and rich conditions: stratified flames are primarily dominated by the diffusion of heat under lean conditions, and diffusion of H2 under rich conditions. Thanks to species and thermal support, stratified flames continue to burn beyond the premixed lean and rich flammability limits. Further investigation on the unsteady response of flames to the fluctuating equivalence ratio implies that the steady results represent the unsteady response well, as long as φ* and ∇φ* are similar in both steady and unsteady cases. © 2013 The Combustion Institute.

On Mixing and Shaking : Structure and Dynamics of Turbulent Stratified Flames

The drive for low emission combustion systems encourages applications using premixed flames. Yet in many applications, considerations of flame stability or mixing times lead to systems with neither premixed nor diffusion flames, which are often called technically premixed or stratified flames. In this talk we discuss the current state of understanding of the effect of mixing and extent of stratification on the structure, microstructure and dynamics of selected turbulent stratified flames. Over the past few years, a significant database of scalar and velocity data has been built to analyze the effects of unmixedness on local and global flame structure. Microscale studies of the flame structures show in detail how the effect of local stratification affects (or not!) the flame structure, flame surface density and scalar dissipation rates, and production of selected species. The experiments place exacting demands on current spectroscopic diagnostics, and reveal the progress and limits to our understanding of turbulent flames in general. The dynamics of stratified flames with respect to instabilities is also shown to be very rich, as the particular shape of the flames and the stabilization points are is significantly affected by the fuel distribution, modifying the rate and location of heat release, and thus the coupling with the surrounding acoustics and determining the onset of self-excitations.

Estimation of the natural purification rate of a eutrophic lake after pollutant removal

Pollution resulting from increased human activities is threatening Lake Donghu, its effects being characterized by serious eutrophication. A steady increase of phosphorus loading is the most important factor of the lake eutrophication. Pollution external control projects are being implemented and will be accomplished before the year 2010. In order to predict the restoration rate by the lake's self-purification after the projects of external control, a model of predicting the removal rate of total phosphorus (TP) from lake water is developed, and a brief method of estimating the release and export rate of sediment phosphorus is suggested. Results show that, on the premise of external loading fully controlled. The restoration needs about 55 years or more. Obviously, the great P pool in the sediment will be a limiting factor of preventing the improvement of water quality after the external loading is under control. Based on the estimation we conclude that after the external control projects before 2010, in order to restore the lake in a few years, although highly cost, the first step must be the sediment dredging to remove internal loading. The second step is diverting water of River Changjiang into the lake to accelerate the improvement of lake water. Otherwise, removal of pollutant sources will become meaningless. (c) 2006 Elsevier B.V. All rights reserved.

Combination of Carbon Nanotubes with Ni2O3 for Simultaneously Improving the Flame Retardancy and Mechanical Properties of Polyethylene

Effects of multiwalled carbon nanotubes (MWCNTs) and Ni2O3 on the flame retardancy of linear low density polyethylene (LLDPE) have been studied. A combination of MWCNTs and Ni2O3 showed a synergistic effect in improving the flame retardancy of LLDPE compared with LLDPE composites containing MWCNTs or Ni2O3 alone. As a result, the peak value of heat release rate measured by cone calorimeter was obviously decreased in the LLDPE/MWCNTs/Ni2O3 Composites. According to the results from rheological tests, carbonization experiments, and structural characterization of residual char, the improved flame retardancy was partially attributed to the formation of a networklike structure due to the good dispersion of MWCNTs in LLDPE matrix, and partially to the carbonization of degradation products of LLDPE catalyzed by Ni catalyst originated from Ni2O3, More importantly, both viscoelastic characteristics and catalytic carbonization behavior of LLDPE/MWCNTs/Ni2O3 composites acted in concert to result in a synergistic effect in improving the flame retardancy.

Boundary layer growth and advection of heat over snow and soil patches: Modelling and parametrization

Essery, RLH, RJ Granger and JW Pomeroy, 2006. Boundary layer growth and advection of heat over snow and soil patches: Modelling and parametrization. Hydrological Processes, 20, 953 - 967.

Ergodicity and Mixing Rate of One-Dimensional Cellular Automata

One-and two-dimensional cellular automata which are known to be fault-tolerant are very complex. On the other hand, only very simple cellular automata have actually been proven to lack fault-tolerance, i.e., to be mixing. The latter either have large noise probability ε or belong to the small family of two-state nearest-neighbor monotonic rules which includes local majority voting. For a certain simple automaton L called the soldiers rule, this problem has intrigued researchers for the last two decades since L is clearly more robust than local voting: in the absence of noise, L eliminates any finite island of perturbation from an initial configuration of all 0's or all 1's. The same holds for a 4-state monotonic variant of L, K, called two-line voting. We will prove that the probabilistic cellular automata Kε and Lε asymptotically lose all information about their initial state when subject to small, strongly biased noise. The mixing property trivially implies that the systems are ergodic. The finite-time information-retaining quality of a mixing system can be represented by its relaxation time Relax(⋅), which measures the time before the onset of significant information loss. This is known to grow as (1/ε)^c for noisy local voting. The impressive error-correction ability of L has prompted some researchers to conjecture that Relax(Lε) = 2^(c/ε). We prove the tight bound 2^(c1log^21/ε) ＜ Relax(Lε) ＜ 2^(c2log^21/ε) for a biased error model. The same holds for Kε. Moreover, the lower bound is independent of the bias assumption. The strong bias assumption makes it possible to apply sparsity/renormalization techniques, the main tools of our investigation, used earlier in the opposite context of proving fault-tolerance.

Cesarean section and rate of subsequent stillbirth, miscarriage and ectopic pregnancy: a Danish register-based cohort study

Background: With cesarean section rates increasing worldwide, clarity regarding negative effects is essential. This study aimed to investigate the rate of subsequent stillbirth, miscarriage, and ectopic pregnancy following primary cesarean section, controlling for confounding by indication. Methods and Findings: We performed a population-based cohort study using Danish national registry data linking various registers. The cohort included primiparous women with a live birth between January 1, 1982, and December 31, 2010 (n = 832,996), with follow-up until the next event (stillbirth, miscarriage, or ectopic pregnancy) or censoring by live birth, death, emigration, or study end. Cox regression models for all types of cesarean sections, sub-group analyses by type of cesarean, and competing risks analyses for the causes of stillbirth were performed. An increased rate of stillbirth (hazard ratio [HR] 1.14, 95% CI 1.01, 1.28) was found in women with primary cesarean section compared to spontaneous vaginal delivery, giving a theoretical absolute risk increase (ARI) of 0.03% for stillbirth, and a number needed to harm (NNH) of 3,333 women. Analyses by type of cesarean section showed similarly increased rates for emergency (HR 1.15, 95% CI 1.01, 1.31) and elective cesarean (HR 1.11, 95% CI 0.91, 1.35), although not statistically significant in the latter case. An increased rate of ectopic pregnancy was found among women with primary cesarean overall (HR 1.09, 95% CI 1.04, 1.15) and by type (emergency cesarean, HR 1.09, 95% CI 1.03, 1.15, and elective cesarean, HR 1.12, 95% CI 1.03, 1.21), yielding an ARI of 0.1% and a NNH of 1,000 women for ectopic pregnancy. No increased rate of miscarriage was found among women with primary cesarean, with maternally requested cesarean section associated with a decreased rate of miscarriage (HR 0.72, 95% CI 0.60, 0.85). Limitations include incomplete data on maternal body mass index, maternal smoking, fertility treatment, causes of stillbirth, and maternally requested cesarean section, as well as lack of data on antepartum/intrapartum stillbirth and gestational age for stillbirth and miscarriage. Conclusions: This study found that cesarean section is associated with a small increased rate of subsequent stillbirth and ectopic pregnancy. Underlying medical conditions, however, and confounding by indication for the primary cesarean delivery account for at least part of this increased rate. These findings will assist women and health-care providers to reach more informed decisions regarding mode of delivery.

Modulation of heat shock transcription factor 1 as a therapeutic target for small molecule intervention in neurodegenerative disease.

Neurodegenerative diseases such as Huntington disease are devastating disorders with no therapeutic approaches to ameliorate the underlying protein misfolding defect inherent to poly-glutamine (polyQ) proteins. Given the mounting evidence that elevated levels of protein chaperones suppress polyQ protein misfolding, the master regulator of protein chaperone gene transcription, HSF1, is an attractive target for small molecule intervention. We describe a humanized yeast-based high-throughput screen to identify small molecule activators of human HSF1. This screen is insensitive to previously characterized activators of the heat shock response that have undesirable proteotoxic activity or that inhibit Hsp90, the central chaperone for cellular signaling and proliferation. A molecule identified in this screen, HSF1A, is structurally distinct from other characterized small molecule human HSF1 activators, activates HSF1 in mammalian and fly cells, elevates protein chaperone expression, ameliorates protein misfolding and cell death in polyQ-expressing neuronal precursor cells and protects against cytotoxicity in a fly model of polyQ-mediated neurodegeneration. In addition, we show that HSF1A interacts with components of the TRiC/CCT complex, suggesting a potentially novel regulatory role for this complex in modulating HSF1 activity. These studies describe a novel approach for the identification of new classes of pharmacological interventions for protein misfolding that underlies devastating neurodegenerative disease.

Analysis of the utility of QuantiFERON-TB gold in tube and measurement of IFNgamma release by peripheral mononuclear cells in response to different mycobacterium antigen in the work-up of patients with uveitis.

Evaluation Studies

In vitro drug release studies of polymeric freeze-dried wafers and solvent-cast films using paracetamol as a model soluble drug

Drug dissolution and release characteristics from freeze-dried wafers and solvent-cast films prepared from sodium carboxymethylcellulose (CMC) have been investigated to determine the mechanisms of drug release from the two systems. The formulations were prepared by freeze-drying (wafers) or drying in air (films), the hydrated gel of the polymer containing paracetamol as a model soluble drug. Scanning electron microscopy (SEM) was used to examine differences between the physical structure of the wafers and films. Dissolution studies were performed using an exchange cell and drug release was measured by UV spectroscopy at 242 nm. The effects of drug loading, polymer content and amount of glycerol (films) on the release characteristics of paracetamol were investigated. The release profiles of paracetamol from the wafers and films were also compared. A digital camera was used to observe the times to complete hydration and dissolution of the wafers containing different amounts of CMC and how that impacts on drug release rates. Both formulations showed sustained type drug release that was modelled by the Korsmeyer–Peppas equation. Changes in the concentration of drug and glycerol (films) did not significantly alter the rate of drug release while increasing polymer content significantly decreased the rate of drug release from both formulations. The results show that the rate of paracetamol release was faster from the wafers than the corresponding films due to differences in their physical structures. The wafers which formed a porous network, hydrated faster than the more dense and continuous, (non-porous) sheet-like structure of the films.