Bioremediation and lipid synthesis through mixotrophic algal consortia in municipal wastewater

Algae grown in outdoor reactors (volume: 10 L and depth: 20 cm) were fed directly with filtered and sterilised municipal wastewater. The nutrient removal efficiencies were 86%, 90%, 89%, 70% and 76% for TOC, TN, NH4-N, TP and OP, respectively, and lipid content varied from 18% to 28.5% of dry algal biomass. Biomass productivity of similar to 122 mg/l/d (surface productivity 24.4 g/m(2)/d) and lipid productivity of similar to 32 mg/l/d were recorded. Gas chromatography and mass spectrometry (GC-MS) analyses of the fatty acid methyl esters (FAME) showed a higher content of desirable fatty acids (bearing biofuel properties) with major contributions from saturates such as palmitic acid C16:0; similar to 40%] and stearic acid C18:0; similar to 34%], followed by unsaturates such as oleic acid C18:1(9); similar to 10%] and linoleic acid C18:2(9,12); similar to 5%]. The decomposition of algal biomass and reactor residues with an exothermic heat content of 123.4 J/g provides the scope for further energy derivation. (C) 2014 Elsevier Ltd. All rights reserved.

Tin-Incorporation Induced Changes in the Microstructural, Optical, and Electrical Behavior of Tungsten Oxide Nanocrystalline Thin Films Grown Via Spray Pyrolysis

Undoped and Sn-doped WO3 thin films were grown on cleaned glass substrates by chemical spray pyrolysis, using ammonium tungstate (NH4)(2)WO4 as the host precursor and tin chloride (SnCl4 center dot 5H(2)O) as the source of dopant. The XRD spectra confirm the monoclinic structure with a sharp narrow peak along (200) direction along with other peaks of low relative intensities for all the samples. On Sn doping, the films exhibit reduced crystallinity relative to the undoped film. The standard deviation for relative peak intensity with dopant concentration shows enhancement in heterogeneous nucleation growth. As evident from SEM images, on Sn doping, appearance of island-like structure (i.e., cluster of primary crystallites at few places) takes place. The transmittance has been found to decrease in all the Sn-doped films. The optical band gap has been calculated for both direct and indirect transitions. On Sn doping, the direct band gap shows a red shift and becomes 2.89 eV at 2 at.% doping. Two distinct peaks, one blue emission at 408 nm and other green emission at 533 nm, have been found in the PL spectra. Electrical conductivity has been found to increase with Sn doping.

Estimation of the components of municipal solid waste settlement

Estimation of the municipal solid waste settlements and the contribution of each of the components are essential in the estimation of the volume of the waste that can be accommodated in a landfill and increase the post-usage of the landfill. This article describes an experimental methodology for estimating and separating primary settlement, settlement owing to creep and biodegradation-induced settlement. The primary settlement and secondary settlement have been estimated and separated based on 100% pore pressure dissipation time and the coefficient of consolidation. Mechanical creep and biodegradation settlements were estimated and separated based on the observed time required for landfill gas production. The results of a series of laboratory triaxial tests, creep tests and anaerobic reactor cell setups were conducted to describe the components of settlement. All the tests were conducted on municipal solid waste (compost reject) samples. It was observed that biodegradation accounted to more than 40% of the total settlement, whereas mechanical creep contributed more than 20% towards the total settlement. The essential model parameters, such as the compression ratio (C-c'), rate of mechanical creep (c), coefficient of mechanical creep (b), rate of biodegradation (d) and the total strain owing to biodegradation (E-DG), are useful parameters in the estimation of total settlements as well as components of settlement in landfill.

Constitutive Model for Strength Characteristics of Municipal Solid Waste

This paper presents modification of the derivation of a previously proposed constitutive model for the prediction of stress-strain behavior of municipal solid waste (MSW) incorporating different mechanisms, such as immediate compression under loading, mechanical creep, and time-dependent biodegradation effect. The model is based on critical state soil mechanics incorporating increments in volumetric strains because of elastic, plastic, creep, and biodegradation effects. The improvement introduced in this paper is the modified critical state surface and considers five variable parameters for the estimation of stress-strain behavior of MSW under different loading conditions. In addition, an expression for the strain hardening rule is derived, with considerations of time-dependent mechanical creep and biodegradation effects. The model is validated using results from experimental studies and data from published literature. The results are also compared with the predictions of the stress-strain response obtained from a well-established hyperbolic model. (c) 2014 American Society of Civil Engineers.

Shear strength characteristics of mechanically biologically treated municipal solid waste (MBT-MSW) from Bangalore

Strength and stiffness properties of municipal solid waste (MSW) are important in landfill design. This paper presents the results of comprehensive testing of shear strength properties of mechanically biologically treated municipal solid waste (MBT-MSW) in laboratory. Changes in shear strength of MSW as a function of unit weight and particle size were investigated by performing laboratory studies on the MSW collected from Mavallipura landfill site in Bangalore. Direct shear tests, small scale and large scale consolidated undrained and drained triaxial tests were conducted on reconstituted compost reject MSW samples. The triaxial test results showed that the MSW samples exhibited a strain-hardening behaviour and the strength of MSW increased with increase in unit weight. Consolidated drained tests showed that the mobilized shear strength of the MSW increased by 40% for a unit weight increase from 7.3 kN/m(3) to 10.3 kN/m(3) at 20% strain levels. The mobilized cohesion and friction angle ranged from 5 to 9 kPa and 8 degrees to 33 degrees corresponding to a strain level of 20%. The consolidated undrained tests exhibited reduced friction angle values compared to the consolidated drained tests. The friction angle increased with increase in the unit weight from 8 degrees to 55 degrees in the consolidated undrained tests. Minor variations were found in the cohesion values. Relationships for strength and stiffness of MSW in terms of strength and stiffness ratios are developed and discussed. The stiffness ratio and the strength ratio of MSW were found to be 10 and 0.43. (c) 2015 Elsevier Ltd. All rights reserved.

Improving the Rigor and Consistency of the Thermodynamic Theory for Clathrate Hydrates through Incorporation of Movement of Water Molecules of Hydrate Lattice

Current applications of statistical thermodynamic theories for clathrate hydrates do not incorporate the translational and rotational movement of water molecules of the hydrate lattice,in a rigorous manner. Previous studies have shown that the movement of water molecules has a significant effect on the properties of clathrate hydrates. In this Article, a method is presented to incorporate the effect of water movement with as much rigor as possible. This method is then used to calculate the Langmuir constant of the guest species in a clathrate hydrate. Unlike previous studies on modeling of clathrate hydrate thermodynamics, the method presented in this paper does not regress either the intermolecular potentials or the properties of the empty hydrate from clathrate phase equilibria data. Also the properties of empty hydrate used in the theory do not depend on the nature and composition of the guest molecules. The predicted phase equilibria from the resulting theory are shown to be highly accurate and thermodynamically consistent by comparing them with the phase equilibria computed directly from molecular simulations.

Efficient Site-Specific Incorporation of Thioamides into Peptides on a Solid Support

Designing bioactive peptides containing thioamide functionality to modulate their pharmacological properties has been thwarted so far because of various synthetic challenges. The fast, efficient, and inexpensive synthesis and incorporation of a wide range of thionated amino acids into a growing peptide chain on a solid support is reported using standard Fmoc-based chemistry. The commonly employed methodology is comprehensively investigated and optimized with significant improvements regarding the quantity of reagents and reaction conditions. The utility of the protocol is further demonstrated in the synthesis of dithionated linear and monothionated cyclic peptides, which has been a daunting task.

Incorporation of Cr3+ ions in tuning the magnetic and transport properties of nano zinc ferrite

Cost effective and low temperature synthesis methods namely solution combustion and hydrothermal methods were used to prepare chromium incorporated nanocrystalline zinc ferrites. The effect of incorporation of low concentration Cr3+ ions on the structural, morphological, magnetic and transport properties of the zinc ferrite compounds were investigated. The crystalline nature and size variation with chromium content were valid from powder x-ray diffraction. Particles size and crystallite size variation were valid from scanning electron microscopy and transmission electron microscopy respectively. With the increase in chromium incorporation, the crystallite and particles sizes were decreased. Fourier transform infrared spectroscopy (FTIR) studies confirmed the presence of strong metal-oxygen bonds. The elastic properties of the materials in both the methods were estimated by FTIR studies. Magnetic properties namely saturation magentization, remanent magnetization and coercivity values were decreased with increase in Cr3+ ions concentration. The dielectric properties of the samples decreased with increase in the Cr3+ ions. The dielectric constant was observed to be of the order of 10(6) at low frequency and almost 1 at higher frequency range. The activation energy estimated using Arrhenius plots was of the order of 0.182 eV and 0.368 eV respectively for the compounds prepared by solution combustion and hydrothermal methods. The emission spectra of the samples excited at 344 nm were reported using photoluminescence (PL) spectroscopy. Further, the approximate energy band gap(E-g) was estimated from PL studies. The E-g of the materials were lie in the range of 2.11-1.98 eV. (C) 2015 Elsevier B.V. All rights reserved.

Seismic characterization and dynamic site response of a municipal solid waste landfill in Bangalore, India

Seismic design of landfills requires an understanding of the dynamic properties of municipal solid waste (MSW) and the dynamic site response of landfill waste during seismic events. The dynamic response of the Mavallipura landfill situated in Bangalore, India, is investigated using field measurements, laboratory studies and recorded ground motions from the intraplate region. The dynamic shear modulus values for the MSW were established on the basis of field measurements of shear wave velocities. Cyclic triaxial testing was performed on reconstituted MSW samples and the shear modulus reduction and damping characteristics of MSW were studied. Ten ground motions were selected based on regional seismicity and site response parameters have been obtained considering one-dimensional non-linear analysis in the DEEPSOIL program. The surface spectral response varied from 0.6 to 2g and persisted only for a period of 1s for most of the ground motions. The maximum peak ground acceleration (PGA) obtained was 0.5g and the minimum and maximum amplifications are 1.35 and 4.05. Amplification of the base acceleration was observed at the top surface of the landfill underlined by a composite soil layer and bedrock for all ground motions. Dynamic seismic properties with amplification and site response parameters for MSW landfill in Bangalore, India, are presented in this paper. This study shows that MSW has less shear stiffness and more amplification due to loose filling and damping, which need to be accounted for seismic design of MSW landfills in India.

Seismic characterization and dynamic site response of a municipal solid waste landfill in Bangalore, India

Seismic design of landfills requires an understanding of the dynamic properties of municipal solid waste (MSW) and the dynamic site response of landfill waste during seismic events. The dynamic response of the Mavallipura landfill situated in Bangalore, India, is investigated using field measurements, laboratory studies and recorded ground motions from the intraplate region. The dynamic shear modulus values for the MSW were established on the basis of field measurements of shear wave velocities. Cyclic triaxial testing was performed on reconstituted MSW samples and the shear modulus reduction and damping characteristics of MSW were studied. Ten ground motions were selected based on regional seismicity and site response parameters have been obtained considering one-dimensional non-linear analysis in the DEEPSOIL program. The surface spectral response varied from 0.6 to 2g and persisted only for a period of 1s for most of the ground motions. The maximum peak ground acceleration (PGA) obtained was 0.5g and the minimum and maximum amplifications are 1.35 and 4.05. Amplification of the base acceleration was observed at the top surface of the landfill underlined by a composite soil layer and bedrock for all ground motions. Dynamic seismic properties with amplification and site response parameters for MSW landfill in Bangalore, India, are presented in this paper. This study shows that MSW has less shear stiffness and more amplification due to loose filling and damping, which need to be accounted for seismic design of MSW landfills in India.

Analysis of ingredient and heating value of municipal solid waste

Great differences between municipal solid wastes(MSW)produced at different places and different times in terms of such parameters as physical ingredient and heating value lead to difficulty in effective handling of MSW. In this paper, ingredient, heating value and their temporal varying trends of typical MSW in Beijing were continuously measured and analyzed. With consideration of the process in pyrolysis and incineration, correlation between physical ingredients and heating values was induced, favorable for evaluation of heating value needed in handling of MSW from simple analysis of physical ingredients of it.

Diagnostico histopatologico de lesiones hepaticas en bovinos faenados en el rastro municipal de Esteli en el periodo de marzo a agosto de 2008

Con el presente trabajo se pretende conocer las lesiones de hígados bovinos decomisados (condenados) en el Rastro Municipal de Estelí del año 2008 y la realización de su diagnóstico histopatológico utilizando la técnica de tinción Hematoxilina. Eosina, además de ampliar los conocimientos de patología bovina en Nicaragua. El Rastro municipal está ubicado al norte de la ciudad en su periferia y en el actual límite del casco urbano. Los datos del presente estudio se obtuvieron de los registros de los animales faenados por mes y los datos de hígados decomisados (condena dos) se obtuvo de la inspección post-mortem del rastro municipal de Estelí lo cual es realizado por el médico veterinario oficial que depende de la alcaldía, dichos datos fueron recopilados en el período comprendido de marzo a agosto del año 2008. El presente estudio fue de tipo descriptivo donde se hicieron los análisis frecuenciales de las distintas variables evaluadas como categoría, clasificación macroscópica y microscópica, pérdidas económicas. Se encontró que de los 59 casos de hígados condenados representa el 4.16% de animales afectados por diversas patologías. Los resultados encontrados según categorías de los animales afectados fueron: 42 Vacas representaron el 71.18%, 16 Vaquillas el 27.11 % y e1 1.69% un Buey. A los cuales se le designó valor numérico 1-Vaquilla; 2-Vaca; 3-Buey. De los 59 bovinos afectados por Afecciones hepáticas, el 51% presentaron hepatitis, el 12% se refiere peri hepatitis, 10% a hepatitis telangiectasia, 5% a hepatitis pigmentación 3.4% hepatitis crónica, hepatitis absceso, peri hepatitis fibrinosa y absceso, y los rangos de 1.7% corresponden a hemorragia, adherencia, telangiectasia absceso, combina 1 y 9, (hepatitis focal crónica, degeneración, hiperplasia de canalículos biliares) 7 y 9 (degeneración, hemorragia, hiperplasia de canalículos biliares). Las pérdidas económicas por la cantidad hígados condenados fue de C$ 14, 160.00 córdobas que en dólares equivale a US$ 734.013.00 de acuerdo a la tasa de cambio del período estudiado.

Diagnostico situacional de cisticercosis porcina en el rastro municipal de Masaya, Nicaragua en el periodo Enero a Julio 2009

La cisticercosis y la teniasis, ocasionadas por Taenia solium, representan un problema de salud pública. Éstas se encuentran asociadas fuertemente con la crianza de cerdos y las deficientes condiciones sanitarias e higiénicas. Cuando una persona come carne de cerdo infectada, mal cocida o cruda, adquiere teniasis. La cisticercosis se adquiere al ingerir alimentos (verduras principalmente) o agua contaminada con materias fecales conteniendo huevecillos de Taenia solium, o por autoinfestación cuando la persona con teniasis no tiene hábitos de higiene adecuados. Con este estudio se propuso determinar el diagnóstico situacional de cisticercosis porcina en el Rastro Municipal de Masaya en el periodo de Enero-Julio 2009. Los cálculos correspondieron a los casos de cerdos infectados con cisticercosis de los diferentes patentados o dueños de cerdos faenados, además de cada uno de los siete meses de estudio y el porcentaje global de los siete meses evaluados. Los datos se tomaron de los registros que se realizaban durante la inspección postmortem por el médico veterinario autorizado por la Alcaldía de Masaya. El método de estudio fue observacional de tipo transversal. Los resultados obtenidos en base al hallazgo de cerdos infectados con cisticercosis es que éste no era disperso, ya que se mantuvo en cerdos faenados de 5 patentados. El mes con mayor afectación fue Marzo con 0.29% y el porcentaje global fue de 0.14% que equivale a 17 cerdos con cisticercos de 11,903 animales faenados. En este estudio no se lograron determinar pérdidas económicas ni las regiones anatómicas de mayor afectación, ya que en el rastro no se lleva control de peso de los animales y los procesos de matanza no se rigen por el Reglamento de Inspección Veterinaria de la carne para la República de Nicaragua, artículo 118, Ministerio Agropecuario y Forestal (MAGFOR).

Nitrogen incorporation into tetrahedral hydrogenated amorphous carbon

Structural changes induced by the incorporation of nitrogen into ta-C : H films have been studied by Electron Energy Loss Spectroscopy, X-Ray Photoelectron Spectroscopy, Fourier Transformed Infrared Spectroscopy and Ultraviolet-Visible Spectroscopy. ta-C:H films have been synthesised using a low pressure Electron Cyclotron Wave Resonance (ECWR) source which provides a plasma beam with a high degree of ionisation and dissociation. Nitrogen was incorporated by adding N2 to the C2H2 plasma used for the deposition of ta-C : H films. The N/C atomic ratio in the films rises rapidly until the N2/C2H2 gas ratio reaches three, and then increases more gradually, while the deposition rate decreases steeply. Chemical sputtering of the forming films and the formation of molecular nitrogen within the films limit the maximum nitrogen content to about N/C = 0.6. For low nitrogen content the films retain their diamond-like properties, however as N/C atomic ratio increases, a polymeric-like material is formed, with >C=N- structures and terminating C=N and NH groups that decrease the connectivity of the network.

Hay autonomía municipal : el caso de la Provincia de Buenos Aires

"Luego de señalar los antecedentes hispánicos de la autonomía municipal en la historia argentina, el trabajo se ocupa de fundamentar esta autonomía a partir de la Constitución Nacional reformada en 1994 y en las correspondientes Constituciones Provinciales. Destaca que las provincias de Santa Fe, Mendoza y Buenos Aires no han consagrado todavía la autonomía municipal en sus textos constitucionales. Se plantean estos problemas: ¿Qué sucedería si un municipio de la Provincia de Buenos Aires dictara su propia carta orgánica? ¿Resultaría constitucional? ¿Constitucional respecto a qué texto constitucional? ¿Se podría, eventualmente, hablar de inconstitucionalidad por omisión en el caso de la Constitución de la Provincia de Buenos Aires en lo que se refiere a la autonomía municipal?"