Continuous monitoring of concrete mechanical properties since an early age to support construction phasing

The assessment of concrete mechanical properties during construction of concrete structures is of paramount importance for many intrinsic operations. However many of the available non-destructive methods for mechanical properties have limitations for use in construction sites. One of such methodologies is EMM-ARM, which is a variant of classic resonant frequency methods. This paper aims to demonstrate the efforts towards in-situ applicability of EMMARM, as to provide real-time information about concrete mechanical properties such as E-modulus and compressive strength. To achieve the aforementioned objective, a set of adaptations to the method have been successfully implemented and tested: (i) the reduction of the beam span; (ii) the use of a different mould material and (iii) a new support system for the beams. Based on these adaptations, a reusable mould was designed to enable easier systematic use of EMMARM. A pilot test was successfully performed under in-situ conditions during a bridge construction.

Influence of the wood mechanical properties in the dovetail joint behavior

The force distribution inside a dovetail joint is complex. Wood is simultaneously loaded in different directions in the several connected surfaces. The analytical solutions available for the analysis of the behavior of those carpentry joints rely on the mechanical properties of wood. In particular, the stiffness properties of wood under compression are crucial for the forces equilibrium. Simulations showed that the stiffness values considered in each of the springs normally assumed in the analytical models, have great influence in the bearing capacity and stiffness of the dovetail joints, with important consequence on the stress distribution over the overall structure. In a wide experimental campaign, the properties under compression of the most common wood species of existing timber structures have been determined. Then, a solved example of a dovetail joint is presented assuming different wood species and the corresponding strength and stiffness properties values obtained in the tests.

Traditional timber frame walls: mechanical behavior analysis and retrofitting

Timber frame construction is characteristic of several historic city centres as well as of vernacular architecture in several countries around the world, either motivated by the availability of materials and construction traditions or by the need of reducing the seismic vulnerability of buildings, namely in south European countries, where this construction technique was adopted for seismic-resistance purposes. From past earthquakes, it has been seen that timber frame construction can be viewed as an interesting technology as it has exhibited a very reasonable behaviour when compared to other traditional construction techniques such as masonry walls. This chapter provides an overview of the main insights on the seismic performance of timber frame buildings from the evidences of past earthquakes and provides the main results of recent research focused on the in-plane cyclic behavior of timber frame walls with distinct geometrical configurations. Additionally, the main seismic performance indexes of timber frame walls, both unreinforced and retrofitted, are presented and discussed in detail.

Creep behaviour of cracked steel fibre reinforced self-compacting concrete laminar structures

Tese de Doutoramento - Civil Engineering

High strain rate constitutive modeling forhistorical structures subjected to blast loading

Doctoral Thesis Civil Engineering

Effect of butadiene/styrene ratio, block structure and carbon nanotube content on the mechanical and electrical properties of thermoplastic elastomers after UV ageing

Thermoplastic elastomers based on a triblock copolymer styrene-butadiene-styrene (SBS) with different butadiene/styrene ratios, block structure and carbon nanotube (CNT) content were submitted to accelerated weathering in a Xenontest set up, in order to evaluate their stability to UV ageing. It was concluded that ageing mainly depends on butadiene/styrene ratio and block structure, with radial block structures exhibiting a faster ageing than linear block structures. Moreover, the presence of carbon nanotubes in the SBS copolymer slows down the ageing of the copolymer. The evaluation of the influence of ageing on the mechanical and electrical properties demonstrates that the mechanical degradation is higher for the C401 sample, which is the SBS sample with the largest butadiene content and a radial block structure. On the other hand, a copolymer derivate from SBS, the styrene-ethylene/butadiene-styrene (SEBS) sample, retains a maximum deformation of ~1000% after 80 h of accelerated ageing. The hydrophobicity of the samples decreases with increasing ageing time, the effect being larger for the samples with higher butadiene content. It is also verified that cytotoxicity increases with increasing UV ageing with the exception of SEBS, which remains not cytotoxic up to 80 h of accelerated ageing time, demonstrating its potential for applications involving exposition to environmental conditions.

Mechanical performance of natural fiber-reinforced composites for the strengthening of masonry

The growing concerns regarding the environmental impact generated by the use of inorganic materials in different fields of application increased the interest towards products based on materials with low environmental impact. In recent years, researchers have turned their attention towards the development of materials obtained from renewable sources, easily recoverable or biodegradable at the end of use. In the field of civil structures, a few attempts have been done to replace the most common composites (e.g. carbon and glass fibers) by materials less harmful to the environment, as natural fibers. This work presents a comprehensive experimental research on the mechanical performance of natural fibers for the strengthening of masonry constructions. Flax, hemp, jute, sisal and coir fibers have been investigated both from physical and mechanical points of view. The fibers with better performance were tested together with three different matrices (two of organic nature) in order to produce composites. These experimental results represent a useful database for understanding the potentialities of natural fibers as strengthening systems.

Assessment of the mechanical performance of recycled unbound materials for pavement subbase layers

The cyclic load triaxial test is a laboratory test that allows studying the mechanical behaviour of unbound granular materials used in base/subbase layers of road pavements. The resilient modulus and permanent strains are required as inputs in structural pavement design. This paper presents some results obtained for recycled materials (crushed concrete aggregate and blended crushed waste aggregate), with a view to promoting their use in pavement structures. Results relating to a reference material (limestone) are also presented, for comparison. All the test results discussed in this paper were obtained in variable cyclic radial pressure (VCP) tests. The tests performed (VCP) aim to study the influence of water content on the resilient modulus of recycled materials, as well as on the resistance to permanent deformation. Using the experimental data as a basis, further modelling work was carried out to establish the stresses developing in base/capping layers in typical Belgian road pavements. These numerical results allow to propose some simplifications of the stress paths applied in the testing procedures and to establish a new test protocol that also considers compaction during construction works. The results of this research work provide an excellent set of findings for the mechanical characterization of unbound base materials through the cyclic triaxial test, and contribute to a better understanding and correct application of recycled materials under geotechnical engineering background

Novel auxetic structures from basalt braided composites for structural applications

Auxetic materials are a class of materials behaves unusual way compared to regular materials i.e. possess negative Poisson’s ratio. This paper reports, the development of auxetic structures based on re-entrant hexagon design from braided composite materials and testing of the mechanical properties (tensile property, auxetic property and work of rupture). The structure developed from glass and basalt braided composite rods and properties were compared between them. Later, the basic re-entrant hexagon design was modified with vertical straight rods to improve their mechanical behavior and their auxetic property was studied. Auxetic behavior of these structures was studied in a tensile testing machine taking video during testing by Digital camera, later the video converted into images to measure the strain values using simple software, ImageJ. Along with experimental work, analytical model was used to calculate the Poisson’s ratio of basic structure and results were compared

Resilience of concrete structures in the marine environment through microstructural innovation

Dissertação de mestrado integrado em Engenharia Civil

A multi–physics approach applied to masonry structures with non–hydraulic lime mortars

Tese de Doutoramento em Engenharia Civil (área de especialização em Engenharia de Estruturas).

Desarrollo sustentable de geoestructuras compuestas por suelo loéssico compactado mejorado con agregado de materiales estabilizantes. Sustainable development of compacted loess soil geo-structures with addition of stabilizing materials.

Los suelos estabilizados mediante compactación, permiten obtener materiales con ventajas ténicas y economicas en diferentes tipos de obras de ingeniería. Ejemplos de su uso se tiene en bases viales de autopistas, rutas o calles urbanas, pistas de aterrizaje, barreras de contención para enterramientos sanitarios o lagunas de estabilización, apoyos de plateas para fundación de edificios, losas industriales, entre otras aplicaciones. Las fallas en este tipo de construcciones pueden resultar en catástrofes ambientales, sociales y elevadas pérdidas económicas, por lo que resulta de gran importancia optimizar el diseño e incrementar la seguridad de este tipo de construcciones. Las obras con estas características involucran grandes volúmenes y/o superficies que requieren controles sistemáticos durante su desarrollo, a los fines de garantizar el cumplimiento de las propiedades de los materiales establecidos en la etapa de diseño. De esta forma, es necesario contar con ensayos de campo sencillos, confiables y eficientes que permitan identificar propiedades físicas, mecánicas e hidráulicas. Las geoestructuras generadas mediante la compactación del suelo próximo al sector de construcción pueden funcionar adecuadamente, con reducidos costos de material y transporte. Su estabilización puede ejecutarse en forma natural, o con la incorporación de agregados minerales como bentonita, cal o cemento. Estas incorporaciones mejoran las propiedades hidráulicas y mecánicas del material, optimizando el comportamiento requerido para la obra. Para establecer la forma en la que estos minerales modifican el comportamiento del suelo local compactado deben realizarse investigaciones especiales con los materiales involucrados. En el ámbito internacional existen numerosas investigaciones sobre comportamiento de suelos compactados, no obstante, si bien aportan antecedentes para la planificación de estudios locales, sus resultados no pueden trasladarse de manera directa. Las características propias del suelo local constituye la principal variable debido a la diversidad en las propiedades geotécnicas de cada Región. Esta investigación, se focaliza en el empleo de suelos limosos de la formación loéssica de la zona central de Argentina. Los suelos de la llanura cordobesa poseen comportamientos particulares, los cuales son contemplados en los diseños presentados como resutado de las investigaciones internacionales. Esta particularidad se relaciona con su inestabilidad, lo que los clasifica como suelos colapsables. Los resultados obtenidos en este trabajo podrán ser extendidos a una gran superficie de la Provincia de Córdoba y a la Región Pampeana en general, a los fines de establecer recomendaciones de diseño y construcción para la confección de Pliegos de Especificaciones Técnicas de diferentes tipos de obras públicas y privadas. El estudio contempla la ejecución de un plan experimental a escala de laboratorio y campo. Los materiales corresponden a suelo limosos puros, y diferentes agregados tales como bentonita, cal y cemento. Se planifican ensayos para evaluar el desempeño del material, a partir de la confección de muestras preparadas con diferentes condiciones de compactación (energía, humedad y método), y en forma de mezcla con los distintos tipos de agregados. Se realizarán ensayos de permeabilidad en celdas de pared rígida y flexible, junto a ensayos mecánicos de compresión confinada, simple y triaxial. Para el trabajo experimental de campo se prevé la ejecución de terraplenes de prueba instrumentados con tensiómetros e infiltrómetros para evaluar el comportamiento hidraúlico en el tiempo, junto con ensayos de penetración y plato de carga para la caracterización mecánica. En forma conjunta se propone el desarrollo de modelos numéricos de caracterización hidromecánica. Stabilized soils by compaction, produce materials technical and economic advantages in different types of engineering works. For example, road bases in highways, roads or city streets, containment barriers for sanitary landfill or stabilization ponds, foundation support of building, industrial flat, and other applications. Failures can result in environmental catastrophes, social, and economic loss, so it is important to optimize the design and increase the safety of such buildings. These works involve large surfaces that require systematic tests during construction, so it is necessary to have simple field tests, reliable and efficient to identify physical, mechanical and hydraulic properties. The geo-structures generated by local soil compaction have reduced material and transportation costs. Stabilization can be naturally, or with the addition of mineral aggregates as bentonite, lime and cement. These additions improve the hydraulic and mechanical properties of the material. So, special investigations should be conducted with the materials involved. There are many international studies on compacted soils behavior but their results can not be transferred directly due to the particularities of regional soils. For this research silty soils of central Argentina are the main focus. The soils of Córdoba plains are instability, so are classified as collapsible soils. The results obtained in this work may be extended to a large area of the Province of Cordoba and the Pampas region in general, in order to establish design and construction recommendations. The study includes laboratory and field tests. The materials are pure silty soil, and different aggregates such as bentonite, lime and cement. Tests are planned to evaluate the performance. Laboratory includes rigid and flexible wall cells, confined, triaxial and simple compression tests. For field experimental instrumented embankments will be constructed. A numerical hydromechanical model will be developed.

Superficial and deep changes of cellular mechanical properties following cytoskeleton disassembly.

The cytoskeleton, composed of actin filaments, intermediate filaments, and microtubules, is a highly dynamic supramolecular network actively involved in many essential biological mechanisms such as cellular structure, transport, movements, differentiation, and signaling. As a first step to characterize the biophysical changes associated with cytoskeleton functions, we have developed finite elements models of the organization of the cell that has allowed us to interpret atomic force microscopy (AFM) data at a higher resolution than that in previous work. Thus, by assuming that living cells behave mechanically as multilayered structures, we have been able to identify superficial and deep effects that could be related to actin and microtubule disassembly, respectively. In Cos-7 cells, actin destabilization with Cytochalasin D induced a decrease of the visco-elasticity close to the membrane surface, while destabilizing microtubules with Nocodazole produced a stiffness decrease only in deeper parts of the cell. In both cases, these effects were reversible. Cell softening was measurable with AFM at concentrations of the destabilizing agents that did not induce detectable effects on the cytoskeleton network when viewing the cells with fluorescent confocal microscopy. All experimental results could be simulated by our models. This technology opens the door to the study of the biophysical properties of signaling domains extending from the cell surface to deeper parts of the cell.

Modelling the mechanical aspects of the curing process of magneto-sensitive elastomeric materials

In this paper, a phenomenologically motivated magneto-mechanically coupled finite strain elastic framework for simulating the curing process of polymers in the presence of a magnetic load is proposed. This approach is in line with previous works by Hossain and co-workers on finite strain curing modelling framework for the purely mechanical polymer curing (Hossain et al., 2009b). The proposed thermodynamically consistent approach is independent of any particular free energy function that may be used for the fully-cured magneto-sensitive polymer modelling, i.e. any phenomenological or micromechanical-inspired free energy can be inserted into the main modelling framework. For the fabrication of magneto-sensitive polymers, micron-size ferromagnetic particles are mixed with the liquid matrix material in the uncured stage. The particles align in a preferred direction with the application of a magnetic field during the curing process. The polymer curing process is a complex (visco) elastic process that transforms a fluid to a solid with time. Such transformation process is modelled by an appropriate constitutive relation which takes into account the temporal evolution of the material parameters appearing in a particular energy function. For demonstration in this work, a frequently used energy function is chosen, i.e. the classical Mooney-Rivlin free energy enhanced by coupling terms. Several representative numerical examples are demonstrated that prove the capability of our approach to correctly capture common features in polymers undergoing curing processes in the presence of a magneto-mechanical coupled load.

Mechanical damage in cotton buds caused by the boll weevil

The boll weevil (Anthonomus grandis Boheman) causes high levels of bud abscission in cotton plants due to feeding or oviposition punctures. It has been reported that abscission is mainly due to enzymes present in the insect's saliva, but mechanical damage could also contribute to square abscission. The objective of this paper was to undertake an analysis of the morphological damages caused by the insect in cotton squares using microscopy. Anthers and ovules are the main target of boll weevil feeding. The process initiates by perforation of young sepal and petal tissues and proceeds with subsequent alimentation on stamen and ovary leading to abscission of floral structures.