Residual monomer of reline acrylic resins - Effect of water-bath and microwave post-polymerization treatments

Objectives. This study compared the residual monomer (RM) in four hard chair-side reline resins (Duraliner II-D, Kooliner-K, Tokuso Rebase Fast-TRF and Ufi Gel hard-UGH) and one heat-polymerized denture base resin (Lucitone 550-L), which was processed using two polymerization cycles (short-LS and long-LL). It was also investigated the effect of two after polymerization treatments on this RM content.Methods. Specimens (n = 18) of each material were produced following the manufacturers' instructions and then divided into three groups. Group I specimens were left untreated (GI-control). Specimens of group II (GII) were given post-polymerization treatment by microwave irradiation. In group III (GIII), specimens were submitted to immersion in water at 55 degrees C (reline resins-10 min; denture base resin L-60min). The RM was analyzed using high performance liquid chromatography (HPLC) and expressed as a percentage of RM. Data were analyzed by two-way ANOVA followed by Tukey's test (alpha = 0.05).Results. Comparing control specimens, statistical differences were found among all materials (p < 0.05), and the results can be arranged as K (1.52%) > D (0.85%) > UGH (0.45%) > LL (0.24%) > TRF (0.14%) > LS (0.08%). Immersion in hot water (GIII) promoted a significant (p < 0.05) reduction in the RM for all materials evaluated compared to control (GI), with the exception of LL specimens. Materials K, UGH and TRF exhibited significantly (p < 0.05) lower values of RM after microwave irradiation (GII) than in the control specimens.Significance. The reduction in RM promoted by water-bath and microwave post-polymerization treatments could improve the mechanical properties and biocompatibility of the relining and denture base materials. (c) 2006 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Small-angle X-ray and nuclear-magnetic resonance study of siloxane-PMMA hybrids prepared by the sol-gel process

Transparent siloxane-polymethylmethacrylate (PMMA) hybrids were synthesized by the sol-gel process through hydrolysis of methacryloxyproyltrimethoxysilane (TMSM), tetramethoxysilane (TMOS) and polymerization of methylmethacrylate (MMA) using benzol peroxide (BPO) as catalyst. These composites have a good chemical stability due to the presence of covalent bonds between the inorganic (siloxane) and organic (PMMA) phases. The effects of siloxane content, pH of the initial sol and BPO content on the structure of the dried gels were analyzed by small-angle X-ray scattering (SAXS). SAXS results revealed the presence of an interference (or correlation) peak at medium q-range for all compositions, suggesting that siloxane groups located at the ends of PMMA chains form isolated clusters that are spatially correlated. The average intercluster distance - estimated from the q-value corresponding to the maximum in SAXS spectra - decreases for samples prepared with increasing amount of TMSM-TMOS. This effect was assigned to the expected increase in the number density of siloxane groups for progressively higher siloxane content. The increase of BPO content promotes a more efficient polymerization of MMA monomers but has no noticeable effect on the average intercluster distance. High pH favors polycondensation reactions between silicon species of both TMOS and TMSM silicon alcoxides, leading to a structure in which all siloxane clusters are bonded to PMMA chains. This effect was confirmed by Si-29 nuclear-magnetic resonance (NMR) measurements.

Thermo-Reversible Sol-Gel Transition of Surface Modified Titanium Poly Oxo Building Blocks

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Corrosion protection of stainless steel by polysiloxane hybrid coatings prepared using the sol-gel process

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Improved Conductivity Induced by Photodesorption in SnO2 Thin Films Grown by a Sol-Gel Dip Coating Technique

Thin films of undoped and Sb-doped SnO2 have been prepared by a sol-gel dip-coating technique. For the high doping level (2-3 mol% Sb) n-type degenerate conduction is expected, however, measurements of resistance as a function of temperature show that doped samples exhibit strong electron trapping, with capture levels at 39 and 81 meV. Heating in a vacuum and irradiation with UV monochromatic light (305 nm) improve the electrical characteristics, decreasing the carrier capture at low temperature. This suggests an oxygen related level, which can be eliminated by a photodesorption process. Absorption spectral dependence indicates an indirect bandgap transition with Eg ≅ 3.5 eV. Current-voltage characteristics indicate a thermionic emission mechanism through interfacial states.

Degree of conversion and molecular weight of one denture base and three reline resins submitted post-polymerization treatments

The effect of post-polymerization treatments (MW-microwave irradiatron and WB-water-bath) on the degree of conversion (DC) of three reline resins (Ufi Gel hard-U, Kooliner-K, and Tokuso Rebase Fast-T) and one denture base resin (Lucitone 550-L), submitted to two polymerization cycles (LS-short and LL-long), was evaluated by using FT-Raman spectroscopy (n = 5). The molecular weight (Mw) of the powder of all materials and of K polymerized specimens (control; MW; and WB; n = 3) was analyzed using GPC. DC data were analyzed using Kruskal-Wallis test (α = .05). For control specimens, there were no significant differences between U (68%) and LL (77%) and among LL, K (81%), and T (84%). LS (92%) had the highest DC (P<0.05). Only material K exhibited an increased DC after WB (P<0.05). All powders had Mw from 4.0 × 105 to 6.5 × 105 and narrow Mw distributions (2.1 to 3.6). Polymerization and post-polymerization produced K specimens with Mw similar to that of K powder.

Effect of a post-polymerization treatments on the flexural strength and vickers hardness of reline and acrylic denture base resins

This study evaluated the effect of water-bath and microwave post-polymerization treatments on the flexural strength and Vickers hardness of four autopolymerizing reline resins (Duraliner II-D, Kooliner-K, Tokuso Rebase Fast-TR and Ufi Gel Hard C-UGH) and one heat-polymerized acrylic resin (Lucitone 550-L), processed using two polymerization cycles (short cycle - 90 minutes at 73°C and 100°C for 30 minutes; and long cycle - 9 hours at 71°C). For each material, thirty specimens (64 x 10 x 3.3 mm) were made and divided into 3 groups (n=10). Specimens were tested after: processing (control group); water-bath at 55°C for 10 minutes (reline materials) or 60 minutes (L); and microwave irradiation. Flexural strength tests were performed at a crosshead speed of 5 mm/min using a three-point bending device with a span of 50 mm. The flexural strengths values were calculated in MPa. One fragment of each specimen was submitted to Vickers hardness test. Data were analyzed by 2-way ANOVA followed by Tukey's HSD test (α=0.05). L microwaved specimens (short cycle) exhibited significantly higher flexural strength means than its respective control group (p<0.05). Water-bath promoted a significant increase (p<0.05) in flexural strength of K and L (long cycle). The hardness of the tested materials was not influenced by the post-polymerization treatments. Post-polymerization treatments could be used to improve the flexural strength of some materials tested.

Aplicação do processo sol-gel na produção de recobrimentos de hidroxiapatita sobre ligas a base de Ti empregadas em implantes odontológicos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Deterministic Solutions for a Step-growth Polymerization

Chain topology, including branch node, chain link and cross-link dynamics that contribute to the number of elastically active strands and junctions, are calculated using purely deterministic derivations. Solutions are not coupled to population density distributions. An eigenzeit transformation assists in the conversion of expressions derived by chemical reaction principles from time to conversion space, yielding transport phenomena type expressions where the rate of change in the molar concentrations of branch nodes with respect to conversion is expressed as functions of the fraction of reactive sites on precursors and reactants. Analogies are hypothesized to exist in cross-linking space that effectively distribute branch nodes with i reacted moieties between cross-links having j bonds extending to the gel. To obtain solutions, reacted sites on nodes or links with finite chain extensions are examined in terms of stoichiometry associated with covalent bonding. Solutions replicate published results based on Miller and Macosko’s recursive procedure and results obtained from truncated weighted sums of population density distributions as suggested by Flory.

A comparative study between crack analysis and a mechanical test for assessing the polymerization stress of restorative composites

Objectives. To verify the hypothesis that crack analysis and a mechanical test would rank a series of composites in a similar order with respect to polymerization stress. Also, both tests would show similar relationships between stress and composite elastic modulus and/or shrinkage. Methods. Soda-lime glass discs (2-mm thick) with a central perforation (3.5-mm diameter) received four Vickers indentations 500 mu m from the cavity margin. The indent cracks were measured (500x) prior and 10 min after the cavity was restored with one of six materials (Kalore/KL, Gradia/GR, Ice/IC, Wave/WV, Majesty Flow/MF, and Majesty Posterior/MP). Stresses at the indent site were calculated based on glass fracture toughness and increase in crack length. Stress at the bonded interface was calculated using the equation for an internally pressurized cylinder. The mechanical test used a universal testing machine and glass rods (5-mm diameter) as substrate. An extensometer monitored specimen height (2 mm). Nominal stress was calculated dividing the maximum shrinkage force by the specimen cross-sectional area. Composite elastic modulus was determined by nanoindentation and post-gel shrinkage was measured using strain gages. Data were subjected to one-way ANOVA/Tukey or Kruskal-Wallis/Mann-Whitney tests (alpha: 5%). Results. Both tests grouped the composites in three statistical subsets, with small differences in overlapping between the intermediate subset (MF, WV) and the highest (MP, IC) or the lowest stress materials (KL, GR). Higher stresses were developed by composites with high modulus and/or high shrinkage. Significance. Crack analysis demonstrated to be as effective as the mechanical test to rank composites regarding polymerization stress. (c) 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Counter-ion effect on surfactant-DNA gel particles as controlled DNA delivery systems

The ability to entrap drugs within vehicles and subsequently release them has led to new treatments for a number of diseases. Based on an associative phase separation and interfacial diffusion approach, we developed a way to prepare DNA gel particles without adding any kind of cross-linker or organic solvent. Among the various agents studied, cationic surfactants offered particularly efficient control for encapsulation and DNA release from these DNA gel particles. The driving force for this strong association is the electrostatic interaction between the two components, as induced by the entropic increase due to the release of the respective counter-ions. However, little is known about the influence of the respective counter-ions on this surfactant-DNA interaction. Here we examined the effect of different counter-ions on the formation and properties of the DNA gel particles by mixing DNA (either single-(ssDNA) or double-stranded (dsDNA)) with the single chain surfactant dodecyltrimethylammonium (DTA). In particular, we used as counter-ions of this surfactant the hydrogen sulfate and trifluoromethane sulfonate anions and the two halides, chloride and bromide. Effects on the morphology of the particles obtained, the encapsulation of DNA and its release, as well as the haemocompatibility of these particles are presented, using counter-ion structure and DNA conformation as controlling parameters. Analysis of the data indicates that the degree of counter-ion dissociation from the surfactant micelles and the polar/hydrophobic character of the counter-ion are important parameters in the final properties of the particles. The stronger interaction with amphiphiles for ssDNA than for dsDNA suggests the important role of hydrophobic interactions in DNA.

Photonen-Aufkonversion in Nanokapseln

Die vorliegende Dissertation zeigt eine erfolgreiche Verknüpfung der Triplett-Triplett-Annihilations-Aufkonversion (TTA-UC) mit möglichen biologischen Anwendungen. Die Grundlage für solche Anwendungen ist ein Transfer der TTA-UC aus seinem üblicherweise verwendeten organischen Medium in eine wässrige Umgebung. Um diesen Transfer zu realisieren, wurden, unter Anwendung der Technik des Miniemulsionsprozesses, in Wasser dispergierte Nanokapseln herstellt. Der Kern dieser Nanokapseln besteht aus einem flüssigen hydrophoben Medium (meist Hexadekan oder Phenylheptadekan), in dem die zur TTA-UC notwendigen Farbstoffe gelöst sind. Dieser flüssige Kern ist vollständig von einer festen Polymerhülle umschlossen und somit isoliert von seiner wässrigen Umgebung. Es wurden insgesamt drei Generationen solcher Nanokapseln hergestellt, die sich hauptsächlich im Herstellungsprozess, aber auch beim Material von Kern und Hülle unterscheiden. Mittels dieser Variationen konnten die Nanokapseln in Bezug auf Effizienz, Anregungswellenlänge und Sauerstoffempfindlichkeit optimiert werden. Bei der ersten Generation wurde die radikalische Miniemulsionspolymerisation zur Kapselbildung verwendet. Die zweite Generation wurde durch die Kombination des Lösungsmittelverdampfungsprozesses mit dem Miniemulsionsprozess entwickelt und liefert somit eine alternative Möglichkeit der Kapselbildung unter milden Reaktionsbedingungen, was eine uneingeschränkte Auswahl der UC-Farbstoffpaare ermöglicht. Durch den Einsatz unterschiedlicher Sensitizer konnte die Anregungswellenlänge der TTA-UC in den roten und in den nahen Infrarot-Bereich des sichtbaren Spektrums verschoben werden. Diese Verschiebung ist im biologischen Anwendungsbereich von enormer Bedeutung, da dort eine Überlappung mit dem natürlichen optischen Fenster von menschlicher Haut und Gewebe stattfindet. Dies reduziert die Streuung der Anregungsquelle im zu untersuchende Medium und ermöglicht hohe Eindringtiefen. Mit den Kapseln der zweiten Generation wurde zum ersten Mal TTA-UC in lebenden HeLa-Zellen (Krebszellen) und MSCs (Mesenchymale Stammzellen) nachgewiesen. Die verzögerte Fluoreszenz aus den Zellen wurde mit biologischen Standardverfahren, sowohl mit der Durchflusszytometrie (FACS) als auch am cLSM nachgewiesen. Besondere Vorteile gegenüber direkter Fluoreszenz konnten bei der Bildgebung von Zellen erreicht werden. Die relativ energiearme Anregungswellenlänge und die dazu anti-Stokes verschobene, detektierte verzögerte UC-Fluoreszenz lieferte eine bessere Bildqualität und eine sehr geringe Phototoxizität der Zellen. Die Kapseln der dritten Generation zeichnen sich durch ihre anorganische, tetraedrisch verknüpfte SiO2-Hülle aus und wurden mittels einer Grenzflächenreaktion (Sol-Gel-Prozess) in Miniemulsion hergestellt. Diese Kapseln weisen im Vergleich zu den Polymernanokapseln eine bessere UC-Effizienz auf und sind zusätzlich stabiler und robuster.

Saccharide based nanocapsules - From monomer building blocks to improved capsules properties

In dieser Arbeit wurde der vielfältige Nutzen von Kohlenhydraten in Nanokapsel Systemen untersucht. Drei verschiedene Nanokapsel-Typen wurden durch Reaktion an der Grenzfläche von inversen Miniemulsionen hergestellt. Es wurde gezeigt, dass die Kohlenhydrate nach Modifizierung als Monomer an der Kapselbildung teilnehmen können, oder zur Erhöhung der Sensitivität eines verkapselten Kontrastmittels beitragen können. Im Folgenden werden die Ergebnisse der einzelnen Projekte zusammengefasst. Eine neuartige Grenzflächen-Synthese zur Herstellung von Nanokapseln wurde entwickelt und untersucht. Bei der Reaktion handelt es sich um eine Ruthenium katalysierte Olefin-Kreuzmetathese, welche für die Reaktion an der Grenzfläche angepasst wurde. Als wasserlösliches Macromonomer wurde Dextranacrylat synthetisiert. Der Reaktionspartner war ein öl-löslichen Phosphoester (Phenyldi(undec-10-en-1-yl)phosphat). Anhand von NMR-Spektren wurde gezeigt, dass die Kapselbildung auf Olefin Kreuzmetathese beruht. Im Vergleich zu konventionellen Estern haben Phosphorester eine weitere Möglichkeit zur chemischen Funktionalisierung. Dies wurde exemplarisch durch die Verwendung von fluoreszenzmarkierten Phosphoestern gezeigt. Die Markierung wurde verwendet, um die pH-induzierte Abbaubarkeit der Nanokapseln mittels Fluoreszenz-Korrelations-Spektroskopie zu beobachten. Ziel des zweiten Projekts war es, Nanostrukturen zu entwickeln, um Infektionen mit Antibiotika-resistenten Bakterien lokal zu behandeln. Dazu wurden mit Dextranmethacrylat vernetzte Poly(acrylamid) basierte Nanogele synthetisiert und Zinknitrat zugesetzt. Die Synthese der Nanogele wurde erweitert, um durch Vernetzung freier Alkoholgruppen mit Toluoldiisocyanat eine Kapselschale zu erhalten. Die Schalenbildung spiegelte sich in einer geringeren Quellbarkeit der Gel- Schale-Hybride wieder. Die erhaltenen Gel-Schale-Hybride waren in der Lage das Wachstum von zwei Methicillin-resistenten Bakterienstämmen (S. aureus) zu unterdrücken und verzögern. Die synthetisierten Hybridstrukturen könnten in der Beschichtung von Wundauflagen Verwendung finden, um bakterielle Infektionen lokal und direkt nach Ausbruch zu behandeln. Ziel des dritten Projektes war es, die wichtigen Parameter in der Herstellung von Nanokapseln mit hoher Kontrastmittel Sensitivität zu identifizieren. Relaxivität/Signalsensitivität des Kontrastmittels ist von großer Bedeutung für die Bildgebung mittels MRI, dies kann durch die Begrenzung der Mobilität des Kontrastmittels erreicht werden. Aufgrund seiner hohen Komplexstabilität und seiner klinischen Bedeutung wurde das Kontrastmittel Gadobutrol für die Verkapselung verwendet. Das Kontrastmittel wurde in Polyharnstoff-Kapseln eingeschlossen, die durch einen inversen Miniemulsion-Prozess hergestellt wurden. Um die Viskosität im Inneren der Nanokapsel zu erhöhen, wurden zusätzlich Saccharose, Dextran und Polyacrylsäure verkapselt. In Gegenwart von Saccharose konnte die Relaxivität verdoppelt werden. Dies gründet sich vermutlich auf einem Second-sphere Effekt der Saccharose, einer auf Wasserstoffbrückenbindungen beruhende Interaktion von Kontrastmittel und Saccharose.

Raft miniemulsion (co)polymerization of methyl methacrylate and n-butyl acrylate

This thesis work is part of a larger synthesis project about alkyd resins from natural sources, copolymerized with methyl acrylate and n-butyl acrylates, which wil be used for coatings purpose. The aim is to control the copolymerization of methyl acrylate and n-butyl acrylate in RAFT miniemulsion. The research was divided into three parts. First the homopolymerization of methyl methacrylate and n-butyl acrylate was studied by varying different parameters such as the amount of surfactant, the amount of initiator, pH, and especially the RAFT agent. Then two macro RAFT agents were synthesized, as suggested by the existing literature. Finally, the two monomers were copolymerized using both the RAFT used for the homopolymerization and those synthesized in the second stage. To verify the obtained control over the polymerization, the synthesized polymers were analyzed by gel permeation chromatography, GPC, thus finding their molecular weight and its polydispersity.

One Pot, Two Step Sequence Converting Atom Transfer Radical Polymerization Directly to Radical Trap-Assisted Atom Transfer Radical Coupling

Monobrominated polystyrene (PStBr) chains were prepared using standard atom transfer radical polymerization (ATRP) procedures at 80 °C in THF, with monomer conversions allowed to proceed to approximately 40%. At this time, additional copper catalyst, reducing agent, and ligand were added to the unpurified reaction mixture, and the reaction was allowed to proceed at 50 °C in an atom transfer radical coupling (ATRC) phase. During this phase, polymerization continued to occur as well as coupling; expected due to the substantial amount of residual monomer remaining. This was confirmed using gel permeation chromatography (GPC), which showed increases in molecular weight not matching a simple doubling of the PStBr formed during ATRP, and an increase in monomer conversion after the second phase. When the radical trap 2-methyl-2-nitrosopropane (MNP) was added to the ATRC phase, no further monomer conversion occurred and the resulting product showed a doubling of peak molecular weight (Mp), consistent with a radical trap-assisted ATRC (RTA-ATRC) reaction.