Suctions, fracture energy, and plastic cracking of cement mortar and concrete

Plastic cracking of cement mortar and concrete is primarily attributable to desiccation by evaporation from unprotected surfaces. This causes high suctions (negative pressures) to develop in the pore water adjacent to these surfaces. Dissolved salts in the pore water can also contribute significantly to suctions. Quantitative expressions are available for all of the components of the total suction. The development of suctions over time is illustrated by the results of desiccation tests conducted on cement mortars, supplemented by data from the literature. It is shown that ambient conditions conducive to plastic cracking can arise almost anywhere, but that the extremely high suctions that develop in mature cement mortar and concrete do not imply that compression failures should occur A high value of fracture energy is derived from data from the desiccation tests that implies that plastic cracking is characterized by a significant zone of plastic straining or microcracking.

Rheology of fresh mortar

Resumen: Los materiales basados en cementos presentan una enorme importancia tecnológica. Para una correcta utilización es necesario que sea posible su transporte y conformado en un estado “fresco”, por lo que es fundamental controlar su comportamiento reológico. En esta conferencia se describe el comportamiento reológico de morteros y productos relacionados, en situaciones prácticas, donde se tratarán casos concretos, y se discutirán las principales características de cada comportamiento. Además, se presentarán los nexos de unión entre la reología y la tecnología de los materiales de la construcción. Abstract: Cement-based materials are of enormous technological importance and their satisfactory performance depends on being able to transport and mould them in the freshly mixed state. This conference describes the rheology of mortars and related products in the context of practical situations, and deals with testing and measurement, together with the main features of their behaviour. It explores the links between rheology and technology.

Dispersion and optimization of a calcium sulfoaluminate mortar prepared with superplasticizer

Calcium sulfoaluminate (CSA) cements/mortars are receiving increasing attention since their manufacture produces less CO2 than ordinary Portland cement (OPC) (up to 22% of decrease depending on its composition). These systems are complex and there are many parameters affecting their hydration mechanism, such as water-to-cement (w/c) ratio, type and amount of sulfate source, and so on. Low w/c ratios, within certain limits, may reduce the porosity and consequently, improve the mechanical strengths. However, it is accompanied by an increasing of viscosity and lack of both workability and homogeneity, with the consequent negative effect on the mechanical properties. The dispersion of the particles through the adsorption of the right amount and type of additives, such as superplasticizers, is a key point to improve the workability of mortars allowing both the preparation of homogeneous mixtures and the reduction of the amount of mixing water. This work deals with the preparation and optimization of homogeneous CSA-mortars with improved mechanical strengths. The optimum amount of superplasticizer was optimized through rheological measurements. The effect of different amounts of the superplasticizer on the viscosity of the mortars, its hydration mechanism and corresponding mechanical properties has been studied and will be discussed.

C-RAM (Counter Rocket, Artillery and Mortar)

Este trabalho de investigação aplicada visa estudar as principais capacidades do sistema C-RAM e a sua aplicabilidade no Exército Português, tendo por objetivo a caracterização e avaliação da possível constituição e modo de emprego de uma unidade C-RAM no Exército Português, de acordo com o poder de fogo, a capacidade radar e a mobilidade. A metodologia de investigação adotada consiste no método analítico e inquisitivo, concretizado pela realização de entrevistas a Oficiais de Artilharia. Como principais conclusões, constatamos que os sistemas Phalanx e Oerlikon se evidenciam como os sistemas C-RAM de eleição, por disporem de alcances e cadências de tiro mais adequadas às necessidades da Artilharia Antiaérea Portuguesa no âmbito da proteção da força, ou de pontos e áreas críticas, contra este tipo de ameaças.

The properties of fly ash based geopolymer mortars made with dune sand

Geopolymer cement utilises industrial by-products and is associated with low CO2 emissions. The use of dune sand as fine aggregate could reduce the environmental impact of mining activities. The present study is to examine the feasibility of using dune sand in geopolymer-based construction materials. The geopolymer mortars made with dune sand (DSM) were prepared by using alkali activators of different cations(Na, K and Na/K). In order to compare, the corresponding geopolymer mortars made with normal sand (NSM) were also prepared. It was found that dune sand has little influence on the strength of geopolymer mortars, especially for K based mortars. However, the alkali cation has significant influence on the compressive strength of geopolymer mortars. This influence was found to be correlated to porosity. Low compressive strength is associated with high porosity. For all investigated alkali cations, the tensile strengths of DSM compare favourably to those predicted by the relevant Standards for construction materials. Based on the experimental results, Australian dune sand can be used as fine aggregate for the production of geopolymer based construction materials.

Strain rate effects for strength of geopolymer concrete

The effects of strain rate on compressive and tensile strength of fly ash based geopolymer concrete were investigated experimentally. Four mixes of geopolymer concrete using different alkaline solutions and under vary curing conditions were prepared. One mix of ordinary Portland cement (OPC) concrete was prepared for comparison. Both Quasi-Static tests using standard MTS and dynamic tests using Split-Hopkinson pressures bar (SHPB) were conducted, which were giving varying strain rate loadings from 10‾⁷ to 103 per second. The strain rate effect is presented as the ratio of dynamic compressive strength to static compressive strength (DIF). Results show that DIFs of geopolymer concrete are generally higher than those of OPC concrete at strain range of 187/s to 346/s (compression tests) and 7/s to 13/s (splitting tensile tests), respectively. This tendency is independent on loading regimes (compression or tension). This suggests that geopolymer concrete can be used as an alternative construction material to OPC concrete for the structures which has a high risk of being subjected to impact loadings.

Damping capacity of fly ash-based geopolymer

As environmentally-friendly materials, geopolymers have the potential to replace ordinary Portland cement (OPC) for the construction of railway sleepers and multi-flue chimneys, where the vibration control capabilities of the material must be considered. The critical damping value (ξ) is the main parameter in relation to vibration reduction. In this study, the traditional logarithmic decrement technique was used to measure the ξ of geopolymers. Geopolymers were prepared by activating fly ash using alkali solutions with different SiO2/Na2O ratios. The results show that the ξ of the geopolymers is similar to that of the OPC counterpart. Finite element analysis (FEM) based on the Rayleigh damping model was conducted to replicate the test results, and scanning electron microscopy and mercury-intrusion porosimetry were used to study the microstructure of the geopolymers. A discussion of the possible damping mechanisms based on the microstructural investigation and the FEM analysis is presented.

An investigation of major factor of influence of strength gain or loss of geopolymer when exposed to 800° C

When fly ash based geopolymer mortars were exposed to an elevated temperature of 800oC, it was found that the strength after the exposure sometimes decreased, but at other times increased compared to the original strength. The aim of this investigation is to find the reason for this contrasting behaviour. Fol-lowing exposure to high temperature, residual strengths of specimens prepared with two different fly ashes, with initial strengths ranging from 5MPa to 60MPa, were investigated. The parameter that was found to have a major influence on the contrasting behaviour was the ductility of the mortars. The results indicate that the higher the ductility the lower the strength loss. This correlation is attributed to the fact that mortars with high ductility could provide higher capacity to accommodate thermal incompatibility than mortars with low ductil-ity. Beyond the particular threshold of ductility, some mortars even increased strength after the exposure, pos-sibly due to sintering.

The properties of fly ash based geopolymer mortars made with dune sand

This paper reports the properties of fly ash based geopolymer mortars made with dune sand. The geopolymer mortars of different cation type, namely sodium based (Na), potassium based (K) and a mixed Na/K, were prepared with dune sand (DS) and river sand (RS). The corresponding geopolymer pastes were also prepared. A series of tests including compressive strength, modulus of elasticity, splitting tensile strength, microanalysis (using scanning electron microscopy), porosity (using mercury intrusion porosimetry), sorptivity and air void (using section analysis method) were carried out. The results showed a strong correlation between strength and porosity of geopolymeric materials. The addition of DS had influences on the chemical compositions and physical properties of geopolymer mortars. These influences were dependent on the type of cation. Based on the results of mechanical properties, DS can be utilised as the fine aggregate for the production of geopolymer based construction material.

Synthesis of a porous sheet-like V₂O₅-CNT nanocomposite using an ice-templating 'bricks-and-mortar' assembly approach as a high-capacity, long cyclelife cathode material for lithium-ion batteries

Tailoring the nanostructures of electrode materials is an effective way to enhance their electrochemical performance for energy storage. Herein, an ice-templating "bricks-and-mortar" assembly approach is reported to make ribbon-like V2O5 nanoparticles and CNTs integrated into a two-dimensional (2D) porous sheet-like V2O5-CNT nanocomposite. The obtained sheet-like V2O5-CNT nanocomposite possesses unique structural characteristics, including a hierarchical porous structure, 2D morphology, large specific surface area and internal conducting networks, which lead to superior electrochemical performances in terms of long-term cyclability and significantly enhanced rate capability when used as a cathode material for LIBs. The sheet-like V2O5-CNT nanocomposite can charge/discharge at high rates of 5C, 10C and 20C, with discharge capacities of approximately 240 mA h g-1, 180 mA h g-1, and 160 mA h g-1, respectively. It also retains 71% of the initial discharge capacity after 300 cycles at a high rate of 5C, with only 0.097% capacity loss per cycle. The rate capability and cycling performance of the sheet-like V2O5-CNT nanocomposite are significantly better than those of commercial V2O5 and most of the reported V2O5 nanocomposite.

An Investigation of Waste Glass-Based Geopolymers Supplemented with Alumina

An increased consideration of sustainability throughout society has resulted in a surge of research investigating sustainable alternatives to existing construction materials. A new binder system, called a geopolymer, is being investigated to supplement ordinary portland cement (OPC) concrete, which has come under scrutiny because of the CO2 emissions inherent in its production. Geopolymers are produced from the alkali activation of a powdered aluminosilicate source by an alkaline solution, which results in a dense three-dimensional matrix of tetrahedrally linked aluminosilicates. Geopolymers have shown great potential as a building construction material, offering similar mechanical and durability properties to OPC. Additionally, geopolymers have the added value of a considerably smaller carbon footprint than OPC. This research considered the compressive strength, microstructure and composition of geopolymers made from two types of waste glass with varying aluminum contents. Waste glass shows great potential for mainstream use in geopolymers due to its chemical and physical homogeneity as well as its high content of amorphous silica, which could eliminate the need for sodium silicate. However, the lack of aluminum is thought to negatively affect the mechanical performance and alkali stability of the geopolymer system. Mortars were designed using various combinations of glass and metakaolin or fly ash to supplement the aluminum in the system. Mortar made from the high-Al glass (12% Al2O3) reached over 10,000 psi at six months. Mortar made from the low-Al glass (<1% Al2O3) did not perform as well and remained sticky even after several weeks of curing, most likely due to the lack of Al which is believed to cause hardening in geopolymers. A moderate metakaolin replacement (25-38% by mass) was found to positively affect the compressive strength of mortars made with either type of glass. Though the microstructure of the mortar was quite indicative of mechanical performance, composition was also found to be important. The initial stoichiometry of the bulk mixture was maintained fairly closely, especially in mixtures made with fine glass. This research has shown that glass has great potential for use in geopolymers, when care is given to consider the compositional and physical properties of the glass in mixture design.

Two main challenges in service description : Web service tunnel vision and semantic myopia

Through media such as newspapers, letterbox flyers, corporate brochures and television we are regularly confronted with descriptions for conventional (bricks 'n' mortar style) services. These representations vary in the terminology utilised, the depth of the description, the aspects of the service that are characterised and their applicability to candidate service requestors. Existing service catalogues (such as the Yellow Pages) provide little relief for service requestors from the burdensome task of discovering, comparing and substituting services. Add to this environment the rapidly evolving area of web services with its associated surfeit of standards, and the result is a considerably fragmented approach to the description of services. It leaves the reality of the Semantic Web somewhat clouded. --------- Let's consider service description briefly, before discussing our concerns with existing approaches to description. The act of describing is performed prior to advertising. This simple fact provides an interesting paradox as services cannot be described exactly before advertisement. This doesn't mean they can't be described comprehensively. By "exactly", we are referring to the fact that context provided by a service requestor (and their service needs) will alter the description of the service that is presented to the discoverer. For example, a service provider who operates a cinema wants to describe the price of their service. Let's say the advertised price is $15. They also want to state that a pensioner discount and a student discount is available which provides a 50% discount. A customer (i.e. service requestor) uses the cinema web site to purchase tickets online. They find the movie of their choice at a time that suits. However, its not until some context is provided by the requestor that the exact price is determined. The requestor might state that they are a pensioner. The same is applicable for a service requestor who purchases multiple tickets perhaps on behalf of other people. The disconnect between when the service is described and when a requestor provides context introduces challenges to the description process. A service provider would be ill-advised to offer independent descriptions that represent all the permutations possible for a single service. The descriptive effort would be prohibitive.