Modelação molecular de associações entre aniões e receptores sintéticos

A aplicação de simulações de mecânica e dinâmica molecular ao estudo de sistemas supramoleculares tem adquirido, ao longo dos últimos anos, enorme relevância. A sua utilização não só tem levado a uma melhor compreensão dos mecanismos de formação desses mesmos sistemas, como também tem fornecido um meio para o desenvolvimento de novas arquitecturas supramoleculares. Nesta tese são descritos os trabalhos de mecânica e dinâmica molecular desenvolvidos no âmbito do estudo de associações supramoleculares entre aniões e receptores sintéticos do tipo [2]catenano, [2]rotaxano e pseudorotaxano. São ainda estudados complexos supramoleculares envolvendo receptores heteroditópicos do tipo calix[4]diquinona e pares iónicos formados por aniões halogeneto e catiões alcalinos e amónio. Os estudos aqui apresentados assentam essencialmente em duas vertentes: no estudo das propriedades dinâmicas em solução dos vários complexos supramoleculares considerados e no cálculo das energias livres de Gibbs de associação relativas dos vários iões aos receptores sintéticos. As metodologias utilizadas passaram por dinâmica molecular convencional e REMD (Replica Exchange Molecular Dynamics), para o estudo das propriedades em solução, e por cálculos de integração termodinâmica e MMPBSA (Molecular Mechanics – Poisson Boltzmann Surface Area), para a computação das energias livres de associação relativas. Os resultados obtidos, além de terem permitido uma visão mais detalhada dos mecanismos envolvidos no reconhecimento e associação dos vários receptores aos aniões e pares iónicos abordados, encontram-se, globalmente, de acordo com os análogos determinados experimentalmente, validando assim as metodologias empregadas. Em jeito de conclusão, investigou-se ainda a capacidade de um dos receptores heteroditópicos estudados para assistir favoravelmente na migração do par iónico KCl através da interface água-clorofórmio. Para tal, foram utilizadas simulações SMD (Steered Molecular Dynamics) para a computação do perfil de energia livre de Gibbs associada à migração do par iónico através da interface.

Fine structure in the time of flight distribution of C2 in laser produced plasma from graphite

Time resolved optical emission spectroscopy is employed to study the expansion dynamics of C2 species in a graphite plasma produced during the Nd : YAG ablation. At low laser fluences a single peak distribution with low kinetic energy is observed. At higher fluences a twin peak distribution is found. It has been noted that these double peak time of flight distribution splits into a triple peak structure at distances >_ 17mm from the target surface. The reason for the occurrence of multiple peak is due to different formation mechanisms of C2 species

Giant step bunching from self-organized coalescence of SrRuO3 islands

Step bunching develops in the epitaxy of SrRuO3 on vicinal SrTiO3(001) substrates. We have investigated the formation mechanisms and we show here that step bunching forms by lateral coalescence of wedgelike three-dimensional islands that are nucleated at substrate steps. After coalescence, wedgelike islands become wider and straighter with growth, forming a self-organized network of parallel step bunches with altitudes exceeding 30 unit cells, separated by atomically flat terraces. The formation mechanism of step bunching in SrRuO3, from nucleated islands, radically differs from one-dimensional models used to describe bunching in semiconducting materials. These results illustrate that growth phenomena of complex oxides can be dramatically different to those in semiconducting or metallic systems.

Single and multiple addition to C60. A computational chemistry study

Des del seu descobriment, a la molècula C60 se li coneixen una varietat de derivats segons el tipus de funcionalització amb propietats fisicoquímiques específiques de gran interès científic. Una sel·lecció de derivats corresponents a addicions simple o múltiple al C60 s'ha considerat en aquest treball d'investigació. L'estudi a nivell de química computacional de diversos tipus d'addició al C60 s'han portat a terme per tal de poder donar resposta a aspectes que experimentalment no s'entenen o són poc clars. Els sistemes estudiats en referència a l'addició simple al C60 han estat en primer lloc els monoiminoful·lerens, C60NR, (de les dues vies proposades per la seva síntesi, anàlisis cinètic i termodinàmic han ajudat a explicar els mecanismes de formació i justificar l'addició a enllaços tipus [5,6]), i en segon lloc els metanoful·lerens i els hidroful·lerens substituits, C60CHR i C60HR, (raons geomètriques, electròniques, energètiques i magnètiques justifiquen el diferent caràcter àcid ente ambdós derivats tenint en compte una sèrie de substituents R amb diferent caràcter electrònic donor/acceptor). Els fluoroful·lerens, C60Fn, i els epoxid ful·lerens, C60On, (anàlisi sistemàtic dels seus patrons d'addició en base a poder justificar la força que els governa han aportat dades complementàries a les poques que existeixen experimentalment al respecte).

Carbon nanotubes formed in graphite after mechanical grinding and thermal annealing

Multi-walled carbon nanotubes with cylindrical and bamboo-type structures are produced in a graphite sample after mechanical milling at ambient temperature and subsequent thermal annealing up to 1400 °C. The ball milling produces a precursor structure and the thermal annealing activates the nanotube growth. Different nanotubular structures indicate different formation mechanisms: multi-wall cylindrical carbon nanotubes are probably formed upon micropores and the bamboo tubes are produced because of the metal catalysts. A two-dimensional growth governed by surface diffusion is believed to be one important factor for the nanotube growth. A potential industrial production method is demonstrated with advantages of large production quantity and low cost.

Pure boron nitride nanowires produced from boron triiodide

A thick layer of pure boron nitride (BN) nanowires with a uniform diameter of 20 nm was synthesized for the first time using a CVD process with a new precursor of boron triiodide (BI3). Transmission electron microscopy revealed a nanocrystalline structure in the BN nanowires and the absence of any catalyst particle. Some BN nanowires self-assembled into thick threads up to several hundred micrometres long on top of the nanowire layer. The nitriding reactions and lack of catalyst suggest new formation mechanisms of the BN nanowires.

Characteristics of the deformed and recrystallised grains obtained after hot plane strain compression of a model Fe-30wt%Ni alloy

The development of physically-based models of microstructural evolution during hot deformation of metallic materials requires knowledge of the grain/subgrain structure and crystallographic texture characteristics over a range of processing conditions. A Fe-30wt%Ni based alloy, retaining a stable austenitic structure at room temperature, was used for modelling the development of austenite microstructure during hot deformation of conventional carbon-manganese steels. A series of plane strain compression tests was carried out at a temperature of 950 °C and strain rates of 10 s-1 and 0.1 s-1 to several strain levels. Evolution of the grain/subgrain structure and crystallographic texture was characterised in detail using quantitative light microscopy and highresolution electron backscatter diffraction. Crystallographic texture characteristics were determined separately for the observed deformed and recrystallised grains. The subgrain geometry and dimensions together with the misorientation vectors across sub-boundaries were quantified in detail across large sample areas and the orientation dependence of these characteristics was determined. Formation mechanisms of the recrystallised grains were established in relation to the deformation microstructure.

A representação social de educação tecnológica de docentes da Rede Federal de Educação Profissional e Tecnológica: CEFETs do Rio Grande do Norte

The aim of this study was to investigate the social representation of technological education teachers at the Federal Technological Education Network. The survey was conducted from 2007 to 2010, and the respondents were 275 teachers, 135 of the Federal Center for Technological Education (CEFET in portuguese) in the state of Amazonas, in Manaus unit headquarters; 140 of the CEFET in the state of Rio Grande do Norte, a unit based in Natal. We adopt the concept of technological education as the top level of professional education, that is to say, the undergraduate programs of short duration called technological courses. The Federal Technological Education Network gathers hundreds of related institutions, coordinated and supervised by the Office of Vocational and Technological Education of the Ministry of Education. Although many of these institutions offer courses in technology education, no research addressing this subject from the perspective of Social Representations Theory (SRT) was found in the literature. We seek to unravel the social representation of technological education of the teachers by adopting the procedural approach of SRT. This is a qualitative approach, focusing on significant aspects of the representative activity and the formation mechanisms of the representation. Therefore, we search the socio-genesis of the representation in the articulations between discourses, social institutions and practices. We initiated the research through applying critical reading and an analytical perspective on the historical and regulatory documents of technological education in Brazil, from the early twentieth century to the present day. We adopt the Procedure for Multiple Classifications (PMC) from the Free Words Association Technique (FWAT) to access the elements of representational content. For the analysis of the data obtained with FWAT and selection of major words / phrases pertinent to the semantic field of education technology, we used Hamlet II software. For the data analysis of PMC and Free Classification (FC) we used the SPSS ® (Statistical Package for the Social Sciences) version 17.0 and used the method of multidimensional scaling - Multidimensional scaling - (MDS). The output from the central MDS takes the form of a set of scatterplots - "perceptual maps" - of which the points are the elements of the representational content. For the FC data analysis we used the Scalogram Multidimensional Analysis (SMA) - which makes use of the original data in its raw form and allows categorical data to be interpreted in the map as measures of (di)similarity. In order to help with the understanding of the settings of the perceptual maps of FC, we used the Content Analysis of the discourse fragments of the teachers interviewed. The results confirm our initial hypothesis regarding the presence of a single plot among the socio-cognitive study subjects, which is the basis for a social representation of technological education in line with the historic assumption of the dichotomy between mental and manual labor. In spite of the three merging representational elements of the representational content, the perceptual maps compiled from the MSA statistics corroborates the dichotomy, with the exception of the map relating to the subgroup of teachers belonging to the humanities

Continuous production of metal matrix composites from the semisolid state

Continuous strip metal matrix composite (MMC) casting of 0.3 mm diameter hard-drawn stainless steel (316L) wire in a quasi-eutectic SnPb (64Sn36Pb) matrix was performed by a two-roll melt drag processing (TRMDping) method, with the wire being dragged through a semisolid puddle with a fibre contact time of approximately 0.2 s. A slag weir placed at the nozzle contained two wire guide holes: one located near the upper roll, and the other located between the rolls. A successful continuous composite strip casting with good fibre alignment was achieved by inserting and embedding the wire into the matrix using the guide hole between the rolls. Degeneration of eutectic/dendrite structures led to the formation of globular structures. The occurrence and formation mechanisms of cracks, de-lamination and voids in the matrix were discussed. TRMDping is economically viable and has significant benefits over other MMC fabrication methods. © (2013) Trans Tech Publications, Switzerland.

Nanoestruturas de GaN crescidas pelas técnicas de epitaxia por magnetron sputtering e epitaxia por feixe molecular

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Experimental and numerical analysis of dry contact in the pin on disc test

The reduction of friction and wear in systems presenting metal-to-metal contacts, as in several mechanical components, represents a traditional challenge in tribology. In this context, this work presents a computational study based on the linear Archard's wear law and finite element modeling (FEM), in order to analyze unlubricated sliding wear observed in typical pin on disc tests. Such modeling was developed using finite element software Abaqus® with 3-D deformable geometries and elastic–plastic material behavior for the contact surfaces. Archard's wear model was implemented into a FORTRAN user subroutine (UMESHMOTION) in order to describe sliding wear. Modeling of debris and oxide formation mechanisms was taken into account by the use of a global wear coefficient obtained from experimental measurements. Such implementation considers an incremental computation for surface wear based on the nodal displacements by means of adaptive mesh tools that rearrange local nodal positions. In this way, the worn track was obtained and new surface profile is integrated for mass loss assessments. This work also presents experimental pin on disc tests with AISI 4140 pins on rotating AISI H13 discs with normal loads of 10, 35, 70 and 140 N, which represent, respectively, mild, transition and severe wear regimes, at sliding speed of 0.1 m/s. Numerical and experimental results were compared in terms of wear rate and friction coefficient. Furthermore, in the numerical simulation the stress field distribution and changes in the surface profile across the worn track of the disc were analyzed. The applied numerical formulation has shown to be more appropriate to predict mild wear regime than severe regime, especially due to the shorter running-in period observed in lower loads that characterizes this kind of regime.

Pratiche del possibile: i Participatory Guarantee Systems e le scelte d'acquisto del consumatore brasiliano

Negli ultimi anni, parallelamente all’espansione del settore biologico, si è assistito a un crescente interesse per i modelli alternativi di garanzia dell’integrità e della genuinità dei prodotti biologici. Gruppi di piccoli agricoltori di tutto il mondo hanno iniziato a sviluppare approcci alternativi per affrontare i problemi connessi alla certificazione di terza parte. Queste pratiche sono note come Sistemi di Garanzia Partecipativa (PGS). Tali modelli: (i) si basano sugli standard di certificazione biologica dell’IFOAM, (ii) riguardano il complesso dei produttori di una comunità rurale, (iii) comportano l’inclusione di una grande varietà di attori e (iv) hanno lo scopo di ridurre al minimo burocrazia e costi semplificando le procedure di verifica e incorporando un elemento di educazione ambientale e sociale sia per i produttori sia per i consumatori. Gli obiettivi di questo lavoro di ricerca: • descrivere il funzionamento dei sistemi di garanzia partecipativa; • indicare i vantaggi della loro adozione nei Paesi in via di sviluppo e non; • illustrare il caso della Rede Ecovida de Agroecologia (Brasile); • offrire uno spunto di riflessione che riguarda il consumatore e la relativa fiducia nel modello PGS. L’impianto teorico fa riferimento alla Teoria delle Convenzioni. Sulla base del quadro teorico è stato costruito un questionario per i consumatori con lo scopo di testare l’appropriatezza delle ipotesi teoriche. I risultati finali riguardano la stima del livello di conoscenza attuale, la fiducia e la volontà d’acquisto dei prodotti PGS da parte dei consumatori nelle aree considerate. Sulla base di questa ricerca sarà possibile adattare ed esportare il modello empirico in altri paesi che presentano economie diverse per cercare di comprendere il potenziale campo di applicazione dei sistemi di garanzia partecipativa.

Chemistry of aerosol particles and fog droplets during fall-winter season in the Po Valley

Air quality represents a key issue in the so-called pollution “hot spots”: environments in which anthropogenic sources are concentrated and dispersion of pollutants is limited. One of these environments, the Po Valley, normally experiences exceedances of PM10 and PM2.5 concentration limits, especially in winter when the ventilation of the lower layers of the atmosphere is reduced. This thesis provides a highlight of the chemical properties of particulate matter and fog droplets in the Po Valley during the cold season, when fog occurrence is very frequent. Fog-particles interactions were investigated with the aim to determine their impact on the regional air quality. Size-segregated aerosol samples were collected in Bologna, urban site, and San Pietro Capofiume (SPC), rural site, during two campaigns (November 2011; February 2013) in the frame of Supersito project. The comparison between particles size-distribution and chemical composition in both sites showed the relevant contribution of the regional background and secondary processes in determining the Po Valley aerosol concentration. Occurrence of fog in November 2011 campaign in SPC allowed to investigate the role of fog formation and fog chemistry in the formation, processing and deposition of PM10. Nucleation scavenging was investigated with relation to the size and the chemical composition of particles. We found that PM1 concentration is reduced up to 60% because of fog scavenging. Furthermore, aqueous-phase secondary aerosol formation mechanisms were investigated through time-resolved measurements. In SPC fog samples have been systematically collected and analysed since the nineties; a 20 years long database has been assembled. This thesis reports for the first time the results of this long time series of measurements, showing a decrease of sulphate and nitrate concentration and an increase of pH that reached values close to neutrality. A detailed discussion about the occurred changes in fog water composition over two decades is presented.

Fabrication of nanoparticles by short-distance sputter deposition

During the past decades, tremendous research interests have been attracted to investigate nanoparticles due to their promising catalytic, magnetic, and optical properties. In this thesis, two novel methods of nanoparticle fabrication were introduced and the basic formation mechanisms were studied. Metal nanoparticles and polyurethane nanoparticles were separately fabricated by a short-distance sputter deposition technique and a reactive ion etching process. First, a sputter deposition method with a very short target-substrate distance is found to be able to generate metal nanoparticles on the glass substrate inside a RIE chamber. The distribution and morphology of nanoparticles are affected by the distance, the ion concentration and the process time. Densely-distributed nanoparticles of various compositions are deposited on the substrate surface when the target-substrate distance is smaller than 130mm. It is much less than the atoms’ mean free path, which is the threshold in previous research for nanoparticles’ formation. Island structures are formed when the distance is increased to 510mm, indicating the tendency to form continuous thin film. The trend is different from previously-reported sputtering method for nanoparticle fabrication, where longer distance between the target and the substrate facilitates the formation of nanoparticle. A mechanism based on the seeding effect of the substrate is proposed to interpret the experimental results. Secondly, in polyurethane nanoparticles’ fabrication, a mechanism is put forward based on the microphase separation phenomenon in block copolymer thin film. The synthesized polymers have formed dispersed and continuous phases because of the different properties between segments. With harder mechanical property, the dispersed phase is remained after RIE process while the continuous phase is etched away, leading to the formation of nanoparticles on the substrate. The nanoparticles distribution is found to be affected by the heating effect, the process time and the plasma power. Superhydrophilic property is found on samples with these two types of nanoparticles. The relationship between the nanostructure and the hydrophilicity is studied for further potential applications.

Quantitative morphometric analysis of lakes using GIS: rectangularity R , ellipticity E , orientation O , and the rectangularity vs. ellipticity index, REi

Quantitative measures of polygon shapes and orientation are important elements of geospatial analysis. These kinds of measures are particularly valuable in the case of lakes, where shape and orientation patterns can help identifying the geomorphological agents behind lake formation and evolution. However, the lack of built-in tools in commercial geographic information system (GIS) software packages designed for this kind of analysis has meant that many researchers often must rely on tools and workarounds that are not always accurate. Here, an easy-to-use method to measure rectangularity R, ellipticity E, and orientation O is developed. In addition, a new rectangularity vs. ellipticity index, REi, is defined. Following a step-by-step process, it is shown how these measures and index can be easily calculated using a combination of GIS built-in functions. The identification of shapes and estimation of orientations performed by this method is applied to the case study of the geometric and oriented lakes of the Llanos de Moxos, in the Bolivian Amazon, where shape and orientation have been the two most important elements studied to infer possible formation mechanisms. It is shown that, thanks to these new indexes, shape and orientation patterns are unveiled, which would have been hard to identify otherwise.