Experimental Investigation of Performance of a Miniature Direct Methanol Fuel Cell in Short-Term Microgravity

Experimental study of a liquid fed direct methanol fuel cell has been conducted in different gravity environments. A small single cell with 5 cm x 5 cm active area has single serpentine channel on the graphite cathode polar plate and 11 parallel straight channels on the graphite anode flow bed. Cell voltage and current have been measured and two-phase flow in anode channels has been in situ visually observed. The experimental results indicate that the effect of gravity on power performance of the direct methanol fuel cell is large when the concentration polarization governs fuel cells operation. Gravitational effect becomes larger at higher current density. Increasing methanol feeding molarity is conducive to weaken the influence of gravity on performance of liquid fed direct methanol fuel cells. Increasing feeding flow rate of methanol solution from 6 to 15 ml/min could reduce the size of carbon dioxide bubbles, while the influence of gravity still exist. Transport phenomena inside direct methanol fuel cells in microgravity is also analyzed and discussed.

Numerical and Experimental Study of the Performance Effects of Varying Vaneless Space and Vane Solidity in Radial Inflow Turbine Stators.

An extensive experimental program has been carried out on a 135?mm tip diameter radial turbine using a variety of stator designs, in order to facilitate direct performance comparisons of varying stator vane solidity and the effect of varying the vaneless space. A baseline vaned stator was designed using commercial blade design software, having 15 vanes and a vane trailing edge to rotor leading edge radius ratio (Rte/rle) of 1.13. Two additional series of stator vanes were designed and manufactured; one series having varying vane numbers of 12, 18, 24, and 30, and a further series with Rte/rle ratios of 1.05, 1.175, 1.20, and 1.25. As part of the design process a series of CFD simulations were carried out in order to guide design iterations towards achieving a matched flow capacity for each stator. In this way the variations in the measured stage efficiency could be attributed to the stator passages only, thus allowing direct comparisons to be made. Interstage measurements were taken to capture the static pressure distribution at the rotor inlet and these measurements were then used to validate subsequent numerical models. The overall losses for different stators have been quantified and the variations in the measured and computed efficiency were used to recommend optimum values of vane solidity and Rte/rle.

A Theoretical and Experimental Study of Resonance in a High Performance Engine Intake System: Part 1

The unsteady gas dynamic phenomena in engine intake systems of the type found in racecars have been examined. In particular, the resonant tuning effects, including cylinder-to-cylinder power variations, which can occur as a result of the interaction between an engine and its airbox have been considered. Frequency analysis of the output from a Virtual 4-Stroke 1D engine simulation was used to characterise the forcing function applied by an engine to an airbox. A separate computational frequency sweeping technique, which employed the CFD package FLUENT, was used to determine the natural frequencies of virtual airboxes in isolation from an engine. Using this technique, an airbox with a natural frequency at 75 Hz was designed for a Yamaha R6 4-cylinder motorcycle engine. The existence of an airbox natural frequency at 75 Hz was subsequently confirmed by an experimental frequency sweeping technique carried out on the engine test bed. A coupled 1D/3D analysis which employed the engine simulation package Virtual 4-Stroke and the CFD package FLUENT, was used to model the combined engine and airbox system. The coupled 1D/3D analysis predicted a 75 Hz resonance of the airbox at an engine speed of 9000 rpm. This frequency was the induction frequency for a single cylinder. An airbox was fabricated and tested on the engine. Static pressure was recorded at a grid of points in the airbox as the engine was swept through a speed range of 3000 to 10000 rpm. The measured engine speed corresponding to resonance in the airbox agreed well with the predicted values. There was also good correlation between the amplitude and phase of the pressure traces recorded within the airbox and the 1D/3D predictions.

Experimental validation of the performance of a microreactor for the high-throughput screening of catalytic coatings

In this paper, the results of computational fluid dynamics simulations of flow, temperature, and concentration distributions used in the design of a microreactor for the high-throughput screening of catalytic coatings (Mies et al., Chem. Eng. J. 2004, 101, 225) are compared with experimental data, and good agreement is obtained in all cases. The experimental results on flow distribution were obtained from laser Doppler anemometry measurements in the range of Reynolds numbers from 6 to 113. The measured flow nonuniformity in the separate reactor compartments was below 2%. The temperature distribution was obtained from thermocouple measurements. The temperature nonuniformity between the reactor compartments was below 3 K at a maximum heat production rate of 1.3 W in ethylene oxidation at 425 degrees C over CuO/Al2O3/Al coatings. With respect to concentration gradients, a deviation from the average rate of reaction of only 2.3% was obtained at realistic process conditions in the ethylene ammoxidation process over identical Co-ZSM-5 coatings in all reactor compartments. The cross talking noise between separate compartments does not exceed 0.1% when the reactor parts have a smooth surface finish. This illustrates the importance of ultraprecision machining of surfaces in microtechnology, when interfaces cannot be avoided.

Experimental and Numerical Evaluation of Thermal Performance of Steered Fibre Composite Laminates

For Variable Stiffness (VS) composites with steered curvilinear tow paths, the fiber orientation angle varies continuously throughout the laminate, and is not required to be straight, parallel and uniform within each ply as in conventional composite laminates. Hence, the thermal properties (conduction), as well as the structural stiffness and strength, vary as functions of location in the laminate, and the associated composite structure is often called a “variable stiffness” composite structure. The steered fibers lead not only to the alteration of mechanical load paths, but also to the alteration of thermal paths that may
result in favorable temperature distributions within the laminate and improve the laminate performance. Evaluation of VS laminate performance under thermal loading is the focus of this chapter. Thermal performance evaluations require experimental and numerical analysis of VS laminates under different processing and loading conditions. One of the advantages of using composite materials in many applications is the tailoring capability of the laminate,
not only during the design phase but also for manufacturing. Heat transfer through variable conduction and chemical reaction (degree of cure) occurring during manufacturing (curing) plays an important role in the final thermal and mechanical performance, and shape of composite structures.

An Experimental and Numerical Study of the Static and Fatigue Performance of a Composite Adhesive Repair

Experimental static and fatigue tension-tension tests were carried out on 5HS/RTM6 composite intact coupons and coupons incorporating adhesively-bonded (FM300-2) stepped flush joints. The results show that the adhesive joint, which is widely used in repairs, significantly reduces the static strength as well as the fatigue life of the composite. Both, the static and the fatigue failure of the ‘repaired’ coupons occur at the adhesive joint and involve crack initiation and propagation. The latter is modelled using interface finite elements based on the decohezive zone approach. The material degradation in the interface constitutive law is described by a damage variable, which can evolve due to the applied loads as well as the number of fatigue cycles. The fatigue formulation, based on a published model, is adapted to fit the framework of the pseudotransient formulation that is used as a numerical tool to overcome convergence difficulties. The fatigue model requires three material parameters. Numerical tests show that a single set of these parameters can be used to recover, very accurately, the experimental S-N relationship. Sensitivity studies show that the results are not mesh dependent.

A Theoretical and Experimental Study of Resonance in a High Performance Engine Intake System: Part 2

The unsteady gas dynamic phenomena in a racecar airbox have been examined, and resonant tuning effects have been considered. A coupled 1D/3D analysis, using the engine simulation package Virtual 4-Stroke and the CFD package FLUENT, was used to model the engine and airbox. The models were experimentally validated. An airbox was designed with a natural frequency in the region of 75 Hz. A coupled 1D/3D analysis of the airbox and a Yamaha R6 4 cylinder engine predicted resonance at the single-cylinder induction frequency; 75 Hz at an engine speed of 9000 rpm.

An experimental and numerical investigation into the seismic performance of a multi-storey concentrically braced plan irregular structure

In this investigation, the seismic torsional response of a multi-storey concentrically braced frame (CBF) plan irregular structure is evaluated numerically and experimentally through a series of hybrid tests. CBF structures have become popular in seismic design because they are one of the most efficient types of steel structures to resist earthquake loading. However, their response under plan irregular conditions has received little focus mostly in part
due to their complex behaviour under seismic loading conditions. The majority of research on the seismic response of plan irregular structures is based purely on numerical investigations. This paper provides much needed experimental investigation of the seismic response of a CBF plan irregular structure with the aim of characterising the response of this class of structure. The effectiveness of the Eurocode 8 torsional effects provision as a method of designing for
low levels of mass eccentricity is evaluated. Results indicate that some of the observations made by purely numerical models are valid in that; torsionally stiff structures perform well and the stiff side of the structure is subjected to a greater ductility demand compared to the flexible side of the structure. The Eurocode 8 torsional effects provision is shown to be adequate in terms of ductility and interstorey drift however the structure performs poorly
in terms of floor rotation. Importantly, stiffness eccentricity occurs when the provision is applied to the structure when no mass eccentricity exists and results in a significant increase in floor rotations.

Gestualidade e expressão musical : estudo experimental sobre a aplicação da teoria do movimento de Rudolf Laban na aprendizagem da regência e seus efeitos na performance e na expressividade musical

A presente investigação teve como objectivo aplicar, em contexto experimental, alguns conceitos e técnicas da Teoria do Movimento de Rudolf Laban numa acção de formação em regência e avaliar os respectivos efeitos nas competências gestuais dos regentes nela participantes. O estudo teve como base teórica o principio de que a gestualidade do regente é uma “manifestação exterior de impulsos interiores…” (Laban, 1978:32) e que a música, na sua essência, é uma “forma simbólica do sentimento humano”, “um movimento sonoro”, “… um análogo da vida emotiva”. (Susanne Langer, 1980:28) Com a adopção destes pressupostos procurou dar-se coerência às diferentes componentes envolvidas na problemática desta investigação. A parte experimental do estudo teve quatro momentos distintos. No primeiro, foi realizada uma gravação-vídeo para documentar os desempenhos dos estagiários antes da realização das formações (gravação pre-test). No segundo momento, os estagiários tiveram ocasião de frequentar um curso de Movimento Laban ministrado por um especialista nesta matéria, convidado para o efeito. Esta acção de formação terminou com uma gravação-vídeo, efectuada nas mesmas condições técnicas e programáticas da anterior (gravação post-test). Em terceiro lugar, realizou-se, sob orientação do autor do presente estudo, uma segunda acção de formação com o objectivo de plasmar os conceitos e técnicas de Laban na gestualidade específica da regência. Como corolário desta formação, foi realizado o último registo-vídeo (gravação repost-test). Estas gravações foram posteriormente editadas sem alterações técnicas e de conteúdo. Os dados, nelas constantes, foram analisados e avaliados por dois especialistas em regência, a partir de questionários previamente concebidos e fornecidos para o efeito. Após leitura dos pareceres dos especialistas expressos nesses questionários, o autor do presente estudo concluiu que a aplicação dos princípios e técnicas de Laban ao ensino da regência podem contribuir para promover, extensivamente, as competências gestuais dos regentes, tanto no plano da sua funcionalidade, como na sua dimensão expressiva.

An experimental comparison between rival theories of rapid automatized naming performance and its relationship to reading

Two studies investigated the degree to which the relationship between rapid automatized naming (RAN) performance and reading development is driven by shared phonological processes. Study 1 assessed RAN, phonological awareness, and reading performance in 1010 7- to -10 year-olds. Results showed that RAN deficits occurred in the absence of phonological awareness deficits. These were accompanied by modest reading delays. In structural equation modeling, solutions where RAN was subsumed within a phonological processing factor did not provide a good fit to the data, suggesting that processes outside phonology may drive RAN performance and its association with reading. Study 2 investigated Kail’s proposal that speed of processing underlies this relationship. Children with single RAN deficits showed slower speed of processing than did closely matched controls performing normally on RAN. However, regression analysis revealed that RAN made a unique contribution to reading even after accounting for processing speed. Theoretical implications are discussed.

An experimental comparison between rival theories of rapid automatized naming performance and its relationship to reading

Two studies investigated the degree to which the relationship between Rapid Automatized Naming (RAN) performance and reading development is driven by shared phonological processes. Study 1 assessed RAN, phonological awareness and reading performance in 1010 children aged 7-10 years. Results showed that RAN deficits occurred in the absence of phonological awareness deficits. These were accompanied by modest reading delays. In structural equation modeling, solutions where RAN was subsumed within a phonological processing factor did not provide a good fit to the data, suggesting that processes outside phonology may drive RAN performance and its association with reading. Study 2 investigated Kail's (1991) proposal that speed of processing underlies this relationship. Children with single RAN deficits showed slower speed of processing than closely matched controls performing normally on RAN. However, regression analysis revealed that RAN made a unique contribution to reading even after accounting for processing speed. Theoretical implications are discussed.

The effects of flavonoid and other polyphenol consumption on cognitive performance: A systematic research review of human experimental and epidemiological studies

Literature reviews suggest flavonoids, a sub-class of polyphenols, are beneficial for cognition. This is the first review examining the effect of consumption of all polyphenol groups on cognitive function. Inclusion criteria were polyphenol vs. control interventions and epidemiological studies with an objective measure of cognitive function. Participants were healthy or mildly cognitively impaired adults. Studies were excluded if clinical assessment or diagnosis of Alzheimer’s disease, dementia, or cognitive impairment was the sole measure of cognitive function, or if the polyphenol was present with potentially confounding compounds such as caffeine (e.g. tea studies) or Ginkgo Biloba. 28 studies were identified; 4 berry juice studies, 4 cocoa studies, 13 isoflavone supplement studies, 3 other supplement studies, and 4 epidemiological surveys. Overall, 16 studies reported cognitive benefits following polyphenol consumption. Evidence suggests that consuming additional polyphenols in the diet can lead to cognitive benefits, however, the observed effects were small. Declarative memory and particularly spatial memory appear most sensitive to polyphenol consumption and effects may differ depending on polyphenol source. Polyphenol berry fruit juice consumption was most beneficial for immediate verbal memory, whereas isoflavone based interventions were associated with significant improvements for delayed spatial memory and executive function. Comparison between studies was hampered by methodological inconsistencies. Hence, there was no clear evidence for an association between cognitive outcomes and polyphenol dose response, duration of intervention, or population studied. In conclusion, however, the findings do imply that polyphenol consumption has potential to benefit cognition both acutely and chronically.

Effects of taper on swimming force and swimmer performance after an experimental ten-week training program

Papoti, M., L.E.B. Martins, S.A. Cunha, A.M. Zagatto, and C.A. Gobatto. Effects of taper on swimming force and swimmer performance after an experimental ten-week training program. J. Strength Cond. Res. 21(2):538-542. 2007.- The purpose of this research was to examine how an 11-day taper after an 8.5-week experimental training cycle affected lactate levels during maximal exercise, mean force, and performance in training swimmers, independent of shaving, psychological changes, and postcompetition effects. Fourteen competition swimmers with shaved legs and torsos were recruited from the São Paulo Aquatic Federation. The training cycle consisted of a basic training period (endurance and quality phases) of 8.5 weeks, with 5,800 m·d -1 mean training volume and 6 d·wk -1 frequency; and a taper period (TP) of 1.5 weeks' duration that incorporated a 48% reduction in weekly volume without altering intensity. Attained swimming force (SF) and maximal performance over 200m maximal swim (Pmax) before and after taper were measured. After taper, SF and Pmax improved 3.6 and 1.6%, respectively (p < 0.05). There were positive correlations (p < 0.05) between SF and Pmax before (r = 0.86) and after (r = 0.83) the taper phase. Peak lactate concentrations after SF were unaltered before (6.79 ± 1.2 mM) and after (7.15 ± 1.8 mM) TP. Results showed that TP improved mean swimming velocity, but not in the same proportion as force after taper, suggesting that there are other factors influencing performance in faster swimming. © 2007 National Strength & Conditioning Association.

Structural properties of beds packed with agro-industrial solid by-products applicable for solid-state fermentation: Experimental data and effects on process performance

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)