Analysis and design of multirate synchronous sampling schemes for sparse multiband signals

We consider the problem of developing efficient sampling schemes for multiband sparse signals. Previous results on multicoset sampling implementations that lead to universal sampling patterns (which guarantee perfect reconstruction), are based on a set of appropriate interleaved analog to digital converters, all of them operating at the same sampling frequency. In this paper we propose an alternative multirate synchronous implementation of multicoset codes, that is, all the analog to digital converters in the sampling scheme operate at different sampling frequencies, without need of introducing any delay. The interleaving is achieved through the usage of different rates, whose sum is significantly lower than the Nyquist rate of the multiband signal. To obtain universal patterns the sampling matrix is formulated and analyzed. Appropriate choices of the parameters, that is the block length and the sampling rates, are also proposed.

Design of universal multicoset sampling patterns for compressed sensing of multiband sparse signals

Many problems in digital communications involve wideband radio signals. As the most recent example, the impressive advances in Cognitive Radio systems make even more necessary the development of sampling schemes for wideband radio signals with spectral holes. This is equivalent to considering a sparse multiband signal in the framework of Compressive Sampling theory. Starting from previous results on multicoset sampling and recent advances in compressive sampling, we analyze the matrix involved in the corresponding reconstruction equation and define a new method for the design of universal multicoset codes, that is, codes guaranteeing perfect reconstruction of the sparse multiband signal.

Hogar digital para servicios FTTH : dispositivos, tecnologías y QoE

FTTH (fibra hasta el hogar) es actualmente, junto con la banda ancha móvil, la principal evolución tecnológica en Redes y Servicios de Telecomunicaciones. Se prevé que en los próximos años, el despliegue de las redes FTTH se vea incrementado de manera significativa, gracias al interés creciente tanto de Operadores de Telecomunicaciones como de Organismos Gubernamentales. Este despliegue (que en el año 2013 ya se está haciendo realidad) llevará servicios de muy alta velocidad (superiores a 100 Mbps, incluso 1 Gbps) de manera masiva a los hogares, exigiendo nuevos requisitos y prestaciones en la red del hogar de los clientes. Se abre aquí, por tanto, un campo de exploración novedoso, incipiente y de requerimientos cada vez más exigentes. De hecho, sin duda, la red del hogar es uno de los elementos fundamentales para el éxito de las redes y servicios en FTTH. Debido a todo lo anterior, se convierte en una necesidad para el sector de las Telecomunicaciones el encontrar soluciones a los problemas anteriormente mencionados. Con objeto de contribuir al análisis de soluciones, este proyecto se enfoca en dos temas, ambos relacionados con la problemática ya mencionada en la red del hogar:  Prospección e identificación de soluciones tecnológicas avanzadas para la red del hogar. Descrito en capítulos 2, 3 y 4. En ellos se realiza un estudio detallado de la situación actual y tendencias futuras de los dispositivos utilizados en la red del hogar. Este estudio está enfocado en la distribución de señales de muy alto ancho de banda (en torno a los 100 Mbps por segundo) en el hogar.  Diseño y desarrollo de una aplicación que permita determinar la calidad de experiencia de cliente (QoE) de un servicio de televisión IP (IPTV). Descrito en capítulos 5 y 6. Se ha seleccionado este tipo de servicios debido a que son los que requieren mayores prestaciones tanto de la red de transporte como de la red del hogar y, al mismo tiempo, son los más complicados de medir debido a la fuerte componente de subjetividad del usuario final. Una red del hogar correctamente diseñada debe cumplir de manera equilibrada los requisitos demandados tanto por el operador como por el cliente o usuario final del servicio. Los requisitos del operador se centran principalmente en el control de la inversión (CAPEX) y del gasto de mantenimiento de la red del hogar (OPEX). El usuario, por otra parte, requiere sencillez en la instalación y mínimo número de elementos a instalar (cero intrusismo, ausencia de cableado). Para adaptarse a estos requerimientos, existe una serie de dispositivos y tecnologías que buscan encontrar el punto de equilibrio entre necesidades de operadores y de clientes finales. Las soluciones actualmente utilizadas pueden dividirse en soluciones cableadas e inalámbricas. También existen soluciones híbridas. Todas ellas se describen en detalle en los capítulos 3 y 4. Al final del estudio se concluye que, con la tecnología actual, es preferible el uso de soluciones cableadas tipo Ethernet o POF. Es recomendable no usar soluciones PLC de manera extensiva (G.hn puede ser una alternativa a futuro) y, en caso de no requerir cableado, utilizar WiFi 11n con frecuencias de 5 GHz, así como sus evoluciones, WiFi 11ac y 11ad. La aplicación desarrollada, explicada en los capítulos 5 y 6, permite capturar y medir en tiempo real la señal de televisión IP que se entrega al usuario. Esta aplicación estimará, a partir de dichas medidas, la calidad de la señal entregada. Para ello tendrá en cuenta el tipo de descodificador utilizado por el usuario así como la red empleada (red FTTH de Telefónica). Esta aplicación podría ser utilizada en los centros de atención técnica de las operadoras de telecomunicaciones, determinando así la relación existente entre reclamaciones recibidas y calidad de servicio medida por la aplicación. Asimismo, aparte de realizar medidas en tiempo real, la aplicación vuelca las medidas realizadas y alarmas detectadas en ficheros log, facilitando el análisis técnico de los problemas e incidencias registrados por dichos centros técnicos. Igualmente, esta aplicación puede ser utilizada para el proceso de certificación de equipamiento de red del hogar o incluso como herramienta para profundizar en parámetros teóricos y criterios de medida de calidad de servicio en IPTV. ABSTRACT. FTTH (Fiber To The Home) and mobile broadband are currently the main technological trend in the Network and Telecommunications Services area. In the next few years, the deployment of FTTH networks will experiment a significant increase, due to the growing interest of both telecommunications operators and government agencies. This deployment (that is becoming a reality) which will massively carry high-speed services to households (speeds of more than 100 Mbps, even 1 Gbps) will demand new requirements and features in the customer’s home network. It can be found here a new and emerging field of exploration, with increasingly demanding requirements. In fact, the home network is one of the key elements for the success of FTTH network and services. Due to the aforementioned, it is a necessity for the telecommunications industry to find solutions to these problems. In order to contribute into the solution analysis, this project focuses on two subjects, both related to the problems of home networking:  Exploratory research and identification of advanced technology solutions for the home network. Described in chapters 2, 3 and 4. These chapters show a detailed study of the current situation and future trends of the devices used at the home network. It focuses on the distribution of very high bandwidth signals (around 100 Mbps per second) in the customer’s home.  Design and development of an application to evaluate customer’s quality of experience (QoE) of an IP television service (IPTV). Described in chapters 5 and 6. IPTV service has been selected because it requires higher performance both from the transport and the home networks and, at the same time, it is the most difficult to measure due to the strong component of subjectivity of the end user. A correct design of the home network must meet the requirements demanded both by the network operator and the customer (end user of the service). Network operator requirements mainly focus on reduced capital expenditures (CAPEX) and operational expenditures (OPEX). Additionally, the final user requires a simple and easy installation and also the minimum number of items to install (zero intrusion, lack of wiring, etc.). Different devices and technologies seek to find a balance between these two requirements (network operators and final users requirements). Solutions available in the market can be divided into wired and wireless. There are also hybrid solutions. All of them are described thoroughly in the first part of the project. The conclusion at the end of the study recommends the use of wired technologies like Ethernet or POF. Additionally, the use of PLC is not advised (G.hn can be an alternative in the future) and, in the case of not requiring wiring, the use of 11ac and 11ad WiFi is advised. The application developed in the second part of the project allows capturing and measuring the real-time IPTV signal delivered to the user. This application will estimate the delivered signal quality from the captured measurements. For this purpose, it will also consider the type of decoder installed on the customer’s premises and the transport network (Telefonica’s FTTH network). This application could be used at the operator’s technical service centres, determining in this way the relationship between user’s complaints and the quality of service measured. Additionally, this application can write all the measurements and alarms in log files, making easier the technical analysis of problems and impairments recorded by the technical centres. Finally, the application can also be used for the certification process of home networking equipment (i.e. decoders) or even as a tool to deepen theoretical parameters and measuring criteria of quality of service in IPTV.

Optically programmable logic cells as basic units for transmission and synchronization of chaotic signals

We proposed an optical communications system, based on a digital chaotic signal where the synchronization of chaos was the main objective, in some previous papers. In this paper we will extend this work. A way to add the digital data signal to be transmitted onto the chaotic signal and its correct reception, is the main objective. We report some methods to study the main characteristics of the resulting signal. The main problem with any real system is the presence of some retard between the times than the signal is generated at the emitter at the time when this signal is received. Any system using chaotic signals as a method to encrypt need to have the same characteristics in emitter and receiver. It is because that, this control of time is needed. A method to control, in real time the chaotic signals, is reported.

Sight distance studies on roads: influence of digital elevation models and roadside elements

Sight distance plays an important role in road traffic safety. Two types of Digital Elevation Models (DEMs) are utilized for the estimation of available sight distance in roads: Digital Terrain Models (DTMs) and Digital Surface Models (DSMs). DTMs, which represent the bare ground surface, are commonly used to determine available sight distance at the design stage. Additionally, the use of DSMs provides further information about elements by the roadsides such as trees, buildings, walls or even traffic signals which may reduce available sight distance. This document analyses the influence of three classes of DEMs in available sight distance estimation. For this purpose, diverse roads within the Region of Madrid (Spain) have been studied using software based on geographic information systems. The study evidences the influence of using each DEM in the outcome as well as the pros and cons of using each model.

Rapid Scan Electron Paramagnetic Resonance (EPR) and Digital EPR Development

Rapid scan electron paramagnetic resonance (EPR) was developed in the Eaton laboratory at the University of Denver. Applications of rapid scan to wider spectra, such as for immobilized nitroxides, spin-labeled proteins, irradiated tooth and fingernail samples were demonstrated in this dissertation. The scan width has been increased from 55 G to 160 G. The signal to noise (S/N) improvement for slowly tumbling spin-labeled protein samples that is provided by rapid scan EPR will be highly advantageous for biophysical studies. With substantial improvement in S/N by rapid scan, the dose estimation for irradiated tooth enamels became more reliable than the traditional continuous wave (CW) EPR. An alternate approach of rapid scan, called field-stepped direct detection EPR, was developed to reconstruct wider EPR signals. A Mn2+ containing crystal was measured by field-stepped direct detection EPR, which had a spectrum more than 6000 G wide. Since the field-stepped direct detection extends the advantages of rapid scan to much wider scan ranges, this methodology has a great potential to replace the traditional CW EPR. With recent advances in digital electronics, a digital rapid scan spectrometer was built based on an arbitrary waveform generator (AWG), which can excite spins and detect EPR signals with a fully digital system. A near-baseband detection method was used to acquire the in-phase and quadrature signals in one physical channel. The signal was analyzed digitally to generate ideally orthogonal quadrature signals. A multiharmonic algorithm was developed that employed harmonics of the modulation frequencies acquired in the spectrometer transient mode. It was applied for signals with complicated lineshapes, and can simplify the selection of modulation amplitude. A digital saturation recovery system based on an AWG was built at X-band (9.6 GHz). To demonstrate performance of the system, the spin-lattice relaxation time of a fused quartz rod was measured at room temperature with fully digital excitation and detection.

Automatic control of attenuation in a digital communication network

This thesis describes the investigation of an adaptive method of attenuation control for digital speech signals in an analogue-digital environment and its effects on the transmission performance of a national telecommunication network. The first part gives the design of a digital automatic gain control, able to operate upon a P.C.M. signal in its companded form and whose operation is based upon the counting of peaks of the digital speech signal above certain threshold levels. A study was ma.de of a digital automatic gain control (d.a.g.c.) in open-loop configuration and closed-loop configuration. The former was adopted as the means for carrying out the automatic control of attenuation. It was simulated and tested, both objectively and subjectively. The final part is the assessment of the effects on telephone connections of a d.a.g.c. that introduces gains of 6 dB or 12 dB. This work used a Telephone Connection Assessment Model developed at The University of Aston in Birmingham. The subjective tests showed that the d.a.g.c. gives advantage for listeners when the speech level is very low. The benefit is not great when speech is only a little quieter than preferred. The assessment showed that, when a standard British Telecom earphone is used, insertion of gain is desirable if speech voltage across the earphone terminals is below an upper limit of -38 dBV. People commented upon the presence of an adaptive-like effect during the tests. This could be the reason why they voted against the insertion of gain at level only little quieter than preferred, when they may otherwise have judged it to be desirable. A telephone connection with a d.a.g.c. in has a degree of difficulty less than half of that without it. The score Excellent plus Good is 10-30% greater.

Pulse compression applied to the detection of F.S.K. and P.S.K. signals

The matched filter detector is well known as the optimum detector for use in communication, as well as in radar systems for signals corrupted by Additive White Gaussian Noise (A.W.G.N.). Non-coherent F.S.K. and differentially coherent P.S.K. (D.P.S.K.) detection schemes, which employ a new approach in realizing the matched filter processor, are investigated. The new approach utilizes pulse compression techniques, well known in radar systems, to facilitate the implementation of the matched filter in the form of the Pulse Compressor Matched Filter (P.C.M.F.). Both detection schemes feature a mixer- P.C.M.F. Compound as their predetector processor. The Compound is utilized to convert F.S.K. modulation into pulse position modulation, and P.S.K. modulation into pulse polarity modulation. The mechanisms of both detection schemes are studied through examining the properties of the Autocorrelation function (A.C.F.) at the output of the P.C.M.F.. The effects produced by time delay, and carrier interference on the output A.C.F. are determined. Work related to the F.S.K. detection scheme is mostly confined to verifying its validity, whereas the D.P.S.K. detection scheme has not been reported before. Consequently, an experimental system was constructed, which utilized combined hardware and software, and operated under the supervision of a microprocessor system. The experimental system was used to develop error-rate models for both detection schemes under investigation. Performances of both F. S. K. and D.P. S. K. detection schemes were established in the presence of A. W. G. N. , practical imperfections, time delay, and carrier interference. The results highlight the candidacy of both detection schemes for use in the field of digital data communication and, in particular, the D.P.S.K. detection scheme, which performed very close to optimum in a background of A.W.G.N.

Detection of signals corrupted by the combination of Gaussian and Non-Gaussian noise

The detection of signals in the presence of noise is one of the most basic and important problems encountered by communication engineers. Although the literature abounds with analyses of communications in Gaussian noise, relatively little work has appeared dealing with communications in non-Gaussian noise. In this thesis several digital communication systems disturbed by non-Gaussian noise are analysed. The thesis is divided into two main parts. In the first part, a filtered-Poisson impulse noise model is utilized to calulate error probability characteristics of a linear receiver operating in additive impulsive noise. Firstly the effect that non-Gaussian interference has on the performance of a receiver that has been optimized for Gaussian noise is determined. The factors affecting the choice of modulation scheme so as to minimize the deterimental effects of non-Gaussian noise are then discussed. In the second part, a new theoretical model of impulsive noise that fits well with the observed statistics of noise in radio channels below 100 MHz has been developed. This empirical noise model is applied to the detection of known signals in the presence of noise to determine the optimal receiver structure. The performance of such a detector has been assessed and is found to depend on the signal shape, the time-bandwidth product, as well as the signal-to-noise ratio. The optimal signal to minimize the probability of error of; the detector is determined. Attention is then turned to the problem of threshold detection. Detector structure, large sample performance and robustness against errors in the detector parameters are examined. Finally, estimators of such parameters as. the occurrence of an impulse and the parameters in an empirical noise model are developed for the case of an adaptive system with slowly varying conditions.

Impact of signal-ASE four-wave mixing on the effectiveness of digital back-propagation in 112 Gb/s PM-QPSK systems

Limitations in the performance of coherent transmission systems employing digital back-propagation due to four-wave mixing impairments are reported for the first time. A significant performance constraint is identified, originating from four-wave mixing between signals and amplified spontaneous emission noise which induces a linear increase in the standard deviation of the received field with signal power, and linear dependence on transmission distance.

Asynchronous digital optical regenerator for 4 x 40 Gbit/s WDM to 160 Gbit/s OTDM conversion

We propose and numerically analyse an asynchronous digital optical regenerator using a single-EAM loop and a novel neighbor-combine approach. It effectively re-synchronizes input signals with arbitrary phases to the local clock, and regenerates signals with high amplitude fluctuation and polarization mode dispersion. We demonstrate the application of this regenerator for 4 x 40 Gbit/s WDM to 160 Gbit/s OTDM conversion.

Asynchronous digital optical regenerator for 4 x 40 Gbit/s WDM to 160 Gbit/s OTDM conversion

We propose and numerically analyse an asynchronous digital optical regenerator using a single-EAM loop and a novel neighbor-combine approach. It effectively re-synchronizes input signals with arbitrary phases to the local clock, and regenerates signals with high amplitude fluctuation and polarization mode dispersion. We demonstrate the application of this regenerator for 4 x 40 Gbit/s WDM to 160 Gbit/s OTDM conversion.

Photonic processing for wideband cancellation and spectral discrimination of RF signals

Photonic signal processing is used to implement common mode signal cancellation across a very wide bandwidth utilising phase modulation of radio frequency (RF) signals onto a narrow linewidth laser carrier. RF spectra were observed using narrow-band, tunable optical filtering using a scanning Fabry Perot etalon. Thus functions conventionally performed using digital signal processing techniques in the electronic domain have been replaced by analog techniques in the photonic domain. This technique was able to observe simultaneous cancellation of signals across a bandwidth of 1400 MHz, limited only by the free spectral range of the etalon. © 2013 David M. Benton.

Dual-polarization multi-band OFDM signals for next generation core networks

Dual-polarization multi-band orthogonal frequency-division multiplexing (DP-MB-OFDM) signals are optimized at data rates up to 500 Gb/s in dispersion compensation fiber (DCF)-free long-haul links. We compare different polarization crosstalk compensation techniques and explore the DP-MB-OFDM transmission distance limitations. In addition, the impact of the OFDM subcarrier number and high-level modulation format on the transmission performance are also investigated. Finally, a comparison is made between DP-MB-OFDM and the industrial solution of single-carrier DP quaternary phase-shift keying (DP-QPSK) at 1000 km.

Fibre impairment compensation using artificial neural network equalizer for high-capacity coherent optical OFDM signals

We propose an artificial neural network (ANN) equalizer for transmission performance enhancement of coherent optical OFDM (C-OOFDM) signals. The ANN equalizer showed more efficiency in combating both chromatic dispersion (CD) and single-mode fibre (SMF)-induced non-linearities compared to the least mean square (LMS). The equalizer can offer a 1.5 dB improvement in optical signal-to-noise ratio (OSNR) compared to LMS algorithm for 40 Gbit/s C-OOFDM signals when considering only CD. It is also revealed that ANN can double the transmission distance up to 320 km of SMF compared to the case of LMS, providing a nonlinearity tolerance improvement of ∼0.7 dB OSNR.