Impact of the fiber type and dispersion management on the performance of a NRZ 16 x 40 Gb/s DWDM transmission system

We examine the impact of the fiber type and dispersion management on the performance of a 16 × 40 Gb/s dense wavelength-division-multiplexing nonreturn-to-zero transmission system. The transmission line is composed of G.652 or G.655 fiber with periodic dispersion compensation and hybrid Raman erbium-doped fiber amplifier amplification.

Nonlinearity management in fiber transmission systems with hybrid amplification

Nonlinearity management in transmission lines with periodic dispersion compensation and hybrid Raman-Erbium doped fiber amplification is studied both analytically and numerically. Different transmission/compensating fiber pairs are considered, with particular focus on the SMF/DCF case. © 2004 Elsevier B.V. All rights reserved.

All-fiber normal-dispersion single-polarization passively mode-locked laser based on a 45°-tilted fiber grating

An all-fiber normal-dispersion Yb-doped fiber laser with 45- tilted fiber grating (TFG) isto the best of our knowledgeexperimentally demonstrated for the first time. Stable linearly-chirped pulses with the duration of 4 ps and the bandwidth of 9 nm can be directly generated from the laser cavity. By employing the 45 TFG with the polarization-dependent loss of 33 dBoutput pulses with high polarization extinction ratio of 26 dB are implemented in the experiment. Our result shows that the 45 TFG can work effectively as a polarizerwhich could be exploited to singlepolarization all-fiber lasers.

An optical pump controlled tunable phase-shifted fiber grating transmission filter

Optical pump controlled, remotely tunable phase-shifted fiber grating transmission filters were analyzed. The transmission peak had a full width hail maximum (FWHM) bandwidth. With increasing control pump power, the resonant peak shifted towards the longer wavelength side. The efficiency of the system was largely affected by the greater number of sections of doped fiber as well as the absence of recirculation of unabsorbed pump beam. The configuration, besides its simplicity and cost-effectiveness, exhibited wavelength-independent pump-induced phase shifts and no anisotropic effects during operation.

Actively mode-locked tunable dual-wavelength erbium-doped fibre laser

Abstract—We report an actively mode-locked tunable dual-wavelength erbium-doped fiber laser that uses parallel amplifiers in order to minimize gain cross-saturation effects. We obtain extremely stable, room-temperature dual-wavelength operation at a modulator drive frequency of 1035.38 MHz (corresponding pulsewidths of 115 and 130 ps). Furthermore, we can independently tune the power and wavelength of each lasing output signal without affecting overall output stability. In particular, we achieve a wavelength separation as narrow as 0.3 nm.

All-fiber 250 MHz fundamental repetition rate pulsed laser with tilted fiber grating polarizer

We demonstrated a high fundamental repetition-rate pulsed erbium-doped fiber laser with all-fiber-integrated configuration. A novel scheme using a 45°-tilted fiber grating as the in-fiber polarizing element was employed to shorten the total cavity length and, thus, increase the fundamental repetition rate of the laser. Dissipative soliton pulses mode-locked with a fundamental repetition rate of 251.3 MHz and pulse duration of 96.7 fs have been achieved from the compact and all-fiber ring cavity laser. Additionally, passively Q-switched pulses were observed from this high fundamental repetition-rate fiber laser, which is the first report on Q-switched fiber laser using a tilted fiber grating.

Polarization attractors in harmonic mode-locked fiber laser with carbon nanotubes

We study polarization dynamics of a harmonic mode-locked erbium-doped fiber laser with carbon nanotubes absorber. New types of vector solitons are shown for multi-pulse and harmonic mode-locked operation with locked, switching and precessing polarization states. © 2014 OSA.

Soliton mode locking fiber laser with an all-fiber polarization interference filter

An erbium doped fiber ring laser achieving soliton mode locking by the use of an intra-cavity all-fiber polarization interference filter (AFPIF) has been demonstrated. To incorporate an AFPIF with relative narrow transmission bandwidth, the laser has produced clean soliton pulses of 1.2 ps duration at a repetition rate of 14.98 MHz with a polarization extinction ratio up to 25.7 dB. Moreover, we have demonstrated that the operating wavelength of the mode locking laser can be tuned over 20 nm range from 1545 to 1565 nm by thermally tuning the AFPIF cavity. © 2012 Optical Society of America.

Flat-top supercontinuum and tunable femtosecond fiber laser sources at 1.9-2.5 μm

We report the high-energy flat-top supercontinuum covering the mid-infrared wavelength range of 1.9-2.5 μm as well as electronically tunable femtosecond pulses between 1.98-2.22 μm directly from the thulium-doped fiber laser amplifier. Comparison of experimental results with numerical simulations confirms that both sources employ the same nonlinear optical mechanism - Raman soliton frequency shift occurring inside the Tm-fiber amplifier. To illustrate that, we investigate two versions of the compact diode-pumped SESAM mode-locked femtosecond thulium-doped all-silica-fiber-based laser system providing either broadband supercontinuum or tunable Raman soliton output, depending on the parameters of the system. The first system operates in the Raman soliton regime providing femtosecond pulses tunable between 1.98-2.22 μm. Wide and continuous spectral tunability over 240 nm was realized by changing only the amplifier pump diode current. The second system generates high-energy supercontinuum with the superior spectral flatness of better than 1 dB covering the wavelength range of 1.9-2.5 μm, with the total output energy as high as 0.284 μJ, the average power of 2.1 W at 7.5 MHz repetition rate. We simulate the amplifier operation in the Raman soliton self-frequency shift regime and discuss the role of induced Raman scattering in supercontinuum formation inside the fiber amplifier. We compare this system with a more traditional 1.85-2.53 μm supercontinuum source in the external highly-nonlinear commercial chalcogenide fiber using the Raman soliton MOPA as an excitation source. The reported systems1 can be readily applied to a number of industrial applications in the mid-IR, including sensing, stand-off detection, medical surgery and fine material processing.

Fiber Bragg Gratings Strain Sensors for Railway Applications

Fiber optical sensors have played an important role in applications for monitoring the health of civil infrastructures, such as bridges, oil rigs, and railroads. Due to the reduction in cost of fiber-optic components and systems, fiber optical sensors have been studied extensively for their higher sensitivity, precision and immunity to electrical interference compared to their electrical counterparts. A fiber Bragg grating (FBG) strain sensor has been employed for this study to detect and distinguish normal and lateral loads on rail tracks. A theoretical analysis of the relationship between strain and displacement under vertical and horizontal strains on an aluminum beam has been performed, and the results are in excellent agreement with the measured strain data. Then a single FBG sensor system with erbium-doped fiber amplifier broadband source has been carried out. Force and temperature applied on the system have resulted in changes of 0.05 nm per 50 με and 0.094 nm per 10 oC at the center wavelength of the FBG. Furthermore, a low cost fiber-optic sensor system with a distributed feedback (DFB) laser as the light source has been implemented. We show that it has superior noise and sensitivity performances compared to strain gauge sensors. The design has been extended to accommodate multiple sensors with negligible cross talk. When two cascaded sensors on a rail track section are tested, strain readings of the sensor 20 inches away from the position of applied force decay to one seventh of the data of the sensor at the applied force location. The two FBG sensor systems can detect 1 ton of vertical load with a square wave pattern and 0.1 ton of lateral loads (3 tons and 0.5 ton, respectively, for strain gauges). Moreover, a single FBG sensor has been found capable of detecting and distinguishing lateral and normal strains applied at different frequencies. FBG sensors are promising alternatives to electrical sensors for their high sensitivity,ease of installation, and immunity to electromagnetic interferences.

Acousto-optic modulation of optical reflection properties in fiber Bragg gratings and the application in fiber lasers

This thesis aims to investigate the interaction of acoustic waves and fiber Bragg gratings (FBGs) in standard and suspended-core fibers (SCFs), to evaluate the influence of the fiber, grating and modulator design on the increase of the modulation efficiency, bandwidth and frequency. Initially, the frequency response and the resonant acoustic modes of a low frequency acousto-optic modulator (f < 1.2 MHz) are numerically investigated by using the finite element method. Later, the interaction of longitudinal acoustic waves and FBGs in SCFs is also numerically investigated. The fiber geometric parameters are varied and the strain and grating properties are simulated by means of the finite element method and the transfer matrix method. The study indicates that the air holes composing the SCF cause a significant reduction of the amount of silica in the fiber cross section increasing acousto-optic interaction in the core. Experimental modulation of the reflectivity of FBGs inscribed in two distinct SCFs indicates evidences of this increased interaction. Besides, a method to acoustically induce a dynamic phase-shift in a chirped FBG employing an optimized design of modulator is shown. Afterwards, a combination of this modulator and a FBG inscribed in a three air holes SCF is applied to mode-lock an ytterbium doped fiber laser. To improve the modulator design for future applications, two other distinct devices are investigated to increase the acousto-optic interaction, bandwidth and frequency (f > 10 MHz). A high reflectivity modulation has been achieved for a modulator based on a tapered fiber. Moreover, an increased modulated bandwidth (320 pm) has been obtained for a modulator based on interaction of a radial long period grating (RLPG) and a FBG inscribed in a standard fiber. In summary, the results show a considerable reduction of the grating/fiber length and the modulator size, indicating possibilities for compact and faster acousto-optic fiber devices. Additionally, the increased interaction efficiency, modulated bandwidth and frequency can be useful to shorten the pulse width of future all-fiber mode-locked fiber lasers, as well, to other photonic devices which require the control of the light in optical fibers by electrically tunable acoustic waves.

Fractional Photothermolysis for the Treatment of Hypertrophic Scars: Clinical Experience of Eight Cases

Hypertrophic scars are common problems and represent a challenging condition to treat. Fractional photothermolysis has been effective at resurfacing photodamaged skin, acne scars, and atrophic scars, but there are few reports on its use for hypertrophic scars. To evaluate the safety and efficacy of 1,550-nm erbium-doped fiber laser treatment of hypertrophic scars in eight patients. Eight patients (skin phototypes II-IV) with hypertrophic scars received monthly treatments with a 1,550-nm erbium-doped fiber laser. Energy settings ranged from 35 to 50 mJ, and eight to 10 passes were applied with treatment levels 6 to 8. An independent physician evaluator assessed the treatment response by comparing pre- and posttreatment clinical photographs using a quartile grading scale (grade 1, <= 25%=minimal to no improvement; grade 2, 26-50%=moderate improvement; grade 3, 51-75%=marked improvement; grade 4, > 75%=near total improvement. At four weeks after the last treatment session, a mean grade of 2.4 was achieved based on an independent physician`s clinical assessment. Improvement in pigmentation occurred in all hyperpigmented scars. Hypertrophic scars can be effectively and safely improved with 1,550-nm erbium-doped fiber laser treatment. The authors have indicated no significant interest with commercial supporters.

Studies on pulp propogation in single mode optical fibres

Studies on pulse propagation in single mode optical fibers have attracted interest from a wide area of science and technology as they have laid down the foundation for an in-depth understanding of the underlying physical principles, especially in the field of optical telecommunications. The foremost among them is discovery of the optical soliton which is considered to be one of the most significant events of the twentieth century owing to its fantastic ability to propagate undistorted over long distances and to remain unaflected after collision with each other. To exploit the important propertia of optical solitons, innovative mathematical models which take into account proper physical properties of the single mode optical fibers demand special attention. This thesis contains a theoretical analysis of the studies on soliton pulse propagation in single mode optical fibers.

Elimination of All-Optical Cycles in Wavelength-Routed Optical Networks

A transparent (wide-area) wavelength-routed optical network may be constructed by using wavelength cross-connect switches connected together by fiber to form an arbitrary mesh structure. The network is accessed through electronic stations that are attached to some of these cross-connects. These wavelength cross-connect switches have the property that they may configure themselves into unspecified states. Each input port of a switch is always connected to some output port of the switch whether or not such a connection is required for the purpose of information transfer. Due to the presence of these unspecified states, there exists the possibility of setting up unintended alloptical cycles in the network (viz., a loop with no terminating electronics in it). If such a cycle contains amplifiers [e.g., Erbium- Doped Fiber Amplifiers (EDFA’s)], there exists the possibility that the net loop gain is greater than the net loop loss. The amplified spontaneous emission (ASE) noise from amplifiers can build up in such a feedback loop to saturate the amplifiers and result in oscillations of the ASE noise in the loop. Such all-optical cycles as defined above (and hereafter referred to as “white” cycles) must be eliminated from an optical network in order for the network to perform any useful operation. Furthermore, for the realistic case in which the wavelength cross-connects result in signal crosstalk, there is a possibility of having closed cycles with oscillating crosstalk signals. We examine algorithms that set up new transparent optical connections upon request while avoiding the creation of such cycles in the network. These algorithms attempt to find a route for a connection and then (in a post-processing fashion) configure switches such that white cycles that might get created would automatically get eliminated. In addition, our call-set-up algorithms can avoid the possibility of crosstalk cycles.

Estudio de limitaciones en sistemas WDM

Los avances tecnológicos de los últimos años han modificado el panorama de las comunicaciones ópticas. Los amplificadores EDFA (Erbium-Doped Fiber Amplifier) han alterado dos aspectos fundamentales de los sistemas WDM (Wavelength Division Multiplexing): el aumento considerable de las distancias de regeneración y además, la tecnología WDM es un medio más económico de incrementar la capacidad de los sistemas que la tecnología TDM (Time Division Multiplexing). Sin embargo, la implementación de sistemas WDM con grandes tramos sin regeneración de señal óptica trae consigo la aparición de nuevos problemas, entre los que se encuentran las no-linealidades en fibra óptica. Estas no-linealidades en fibras de sílice se pueden clasificar en dos categorías: dispersión estimulada (de Raman y de Brillouin) y efectos debidos al índice no lineal de refracción (automodulación y modulación cruzada de fase y mezcla de cuatro ondas). Este Proyecto Fin de Carrera pretende ser un estudio teórico que refleje el actual Estado del Arte de los principales efectos no-lineales que se producen en los sistemas WDM: dispersión estimulada de Raman (SRS, Stimulated Raman Scattering), dispersión estimulada de Brillouin (SBS,Stimulated Brilfouin Scattering), automodulación de fase (SPM, Self-Phase Modulation), modulación cruzada de fase (XPM, Cross-Phase Modulation) y mezcla de cuatro ondas (FWM, Four-Wave Mixing).