988 resultados para Condutividade eletrica


Relevância:

20.00% 20.00%

Publicador:

Resumo:

This dissertation focuses on rock thermal conductivity and its correlations with petrographic, textural, and geochemical aspects, especially in granite rocks. It aims at demonstrating the relations of these variables in an attempt to enlighten the behavior of thermal effect on rocks. Results can be useful for several applications, such as understanding and conferring regional thermal flow results, predicting the behavior of thermal effect on rocks based upon macroscopic evaluation (texture and mineralogy), in the building construction field in order to provide more precise information on data refinement on thermal properties emphasizing a rocky material thermal conductivity, and especially in the dimension stone industry in order to open a discussion on the use of these variables as a new technological parameter directly related to thermal comfort. Thermal conductivity data were obtained by using Anter Corporation s QuicklineTM -30 a thermal property measuring equipment. Measurements were conducted at temperatures ranging between 25 to 38 OC in samples with 2cm in length and an area of at least 6cm of diameter. As to petrography data, results demonstrated good correlations with quartz and mafics. Linear correlation between mineralogy and thermal conductivity revealed a positive relation of a quartz percentage increase in relation to a thermal conductivity increase and its decrease with mafic minerals increase. As to feldspates (K-feldspate and plagioclase) they show dispersion. Quartz relation gets more evident when compared to sample sets with >20% and <20%. Sets with more than 20% quartz (sienogranites, monzogranites, granodiorites, etc.), exhibit to a great extent conductivity values which vary from 2,5 W/mK and the set with less than 20% (sienites, monzonites, gabbros, diorites, etc.) have an average thermal conductivity below 2,5 W/mK. As to textures it has been verified that rocks considered thick/porphyry demonstrated in general better correlations when compared to rocks considered thin/medium. In the case of quartz, thick rocks/porphyry showed greater correlation factors when compared to the thin/medium ones. As to feldspates (K-feldspate and plagioclase) again there was dispersion. As to mafics, both thick/porphyry and thin/medium showed negative correlations with correlation factor smaller than those obtained in relation to the quartz. As to rocks related to the Streckeisen s QAP diagram (1976), they tend to fall from alcali-feldspates granites to tonalites, and from sienites to gabbros, diorites, etc. Thermal conductivity data correlation with geochemistry confirmed to a great extent mineralogy results. It has been seen that correlation is linear if there is any. Such behavior could be seen especially with the SiO2. In this case similar correlation can be observed with the quartz, that is, thermal conductivity increases as SiO2 is incremented. Another aspect observed is that basic to intermediate rocks presented values always below 2,5 W/mK, a similar behavior to that observed in rocks with quartz <20%. Acid rocks presented values above 2,5 W/mK, a similar behavior to that observed in rocks with quartz >20% (granites). For all the other cases, correlation factors are always low and present opposite behavior to Fe2O3, CaO, MgO, and TiO2. As to Al2O3, K2O, and Na2O results are not conclusive and are statistically disperse. Thermal property knowledge especially thermal conductivity and its application in the building construction field appeared to be very satisfactory for it involves both technological and thermal comfort aspects, which favored in all cases fast, cheap, and precise results. The relation between thermal conductivity and linear thermal dilatation have also shown satisfactory results especially when it comes to the quartz role as a common, determining phase between the two variables. Thermal conductivity studies together with rocky material density can function as an additional tool for choosing materials when considering structural calculation aspects and thermal comfort, for in the dimension stone case there is a small density variation in relation to a thermal conductivity considerable variation

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Relevância:

20.00% 20.00%

Publicador:

Resumo:

O teste de condutividade elétrica tem sido excelente ferramenta para avaliar a qualidade de sementes de diversas espécies e, mais recentemente, estudos têm sido conduzidos visando verificar sua aplicabilidade em sementes florestais. Assim este trabalho objetivou estabelecer metodologia específica do teste de condutividade elétrica para sementes de branquilho. Foram usados três lotes de sementes resultantes do armazenamento em embalagens de vidro (Lote I), pano (Lote II) e papel (Lote III), em câmara fria (10ºC e 60% UR), por cinco meses, os quais foram submetidos ao teste de germinação, avaliando-se a porcentagem e o índice de velocidade de germinação. No teste de condutividade elétrica foram estudadas três quantidades de sementes por repetição (25, 50 e 75 sementes), três volumes de água deionizada (50, 75 e 100mL) e 11 tempos de embebição das sementes (2, 4, 6, 12, 18, 24, 30, 36, 42, 48 e 72h), a 25ºC. O lote I apresentou maior porcentagem e velocidade de germinação. O teste de condutividade elétrica possibilitou a mesma discriminação dos lotes que o teste de germinação, em combinações variadas dos fatores estudados. Foi possível separar o lote de melhor qualidade fisiológica (Lote I) dos demais lotes, já a partir de 2 horas de embebição, utilizando-se amostras de 75 sementes embebidas em 50, 75 ou 100mL de água; ou amostras de 50 sementes embebidas em 50mL de água, a partir de 18 horas de embebição. Desta forma, pode-se recomendar o uso de 75 sementes, embebidas em 75mL de água, por 24 horas à temperatura de 25ºC, para a condução do teste de condutividade elétrica.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

A qualidade da semente na produção agrícola é um dos principais fatores a ser considerado na implantação da cultura, de forma que se torna importante a obtenção de informações sobre a germinação e o vigor das sementes, além da necessidade de avaliá-los. Dentro desse contexto, este trabalho teve como objetivo adequar a metodologia do teste de condutividade elétrica para a avaliação da qualidade fisiológica de sementes de Pisum sativum subsp. arvense. Para tanto, foram utilizados dez lotes de sementes da cultivar IAPAR 83, empregando-se períodos de condicionamento de 8, 16, 20, 24 e 28 horas, combinados às temperaturas de 20 e 25°C e volumes de 75 e 250mL de água. Além destes, foram conduzidos os testes de germinação, primeira contagem de germinação e emergência de plântulas. Para ambas as avaliações, foram utilizadas quatro repetições de 50 sementes. Os testes de vigor, assim como o teste de germinação foram sensíveis para avaliar a qualidade das sementes dos diferentes lotes estudados, porém houve variações na ordenação deles quanto ao vigor. O volume de água, o tempo e a temperatura de embebição influenciaram os valores de condutividade elétrica. Concluiu-se que o teste de condutividade elétrica utilizando 250mL de água, na temperatura de 25°C por 24 horas é promissor para a diferenciação de lotes de sementes de P. sativum subsp. arvense.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Sementes de tomate, sendo dois lotes comerciais do cultivar Petomech e dois lotes do cultivar Santa Clara, foram estudados com o objetivo de se avaliar as variações nos resultados de teste de condutividade elétrica, em função do período de embebição (6, 12, 18 e 24 horas) e do número de sementes utilizadas no teste (25, 50 e 100), procurando-se relacionar os resultados com a emergência das plântulas e o desempenho das sementes em outros testes, em tres épocas de avaliação. Os resultados obtidos mostraram comportamento diferenciado dos cultivares, com valores mais altos de condutividade elétrica para as sementes do cultivar Petomech. Observaram-se também diferenças acentuadas entre os dois lotes do cultivar Petomech em termos de condutividade. Os acréscimos dos valores de condutividade com o decorrer da embebição corresponderam a queda no vigor das sementes independentemente do cultivar.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

20.00% 20.00%

Publicador:

Resumo:

A água subterrânea é um importante recurso ao abastecimento público, principalmente para comunidades periféricas em grandes cidades ou pequenos municípios, onde a instalação ou prolongamento de sistemas de distribuição são economicamente inviáveis. Estudos voltados à análise da vulnerabilidade de aquíferos são relevantes para subsídio a políticas públicas em saneamento básico e preservação ambiental. Este estudo contou com o cadastro de 23 poços rasos localizados no município de Caçapava do Sul (RS), onde foram realizadas medidas de resistividade elétrica e cargabilidade por meio de geofísica, e medidas diretas de condutividade hidráulica e sólidos totais dissolvidos. A análise estatística dos dados demonstrou diversos graus de correlação entre parâmetros, basicamente condicionados a fatores geológicos como porosidade, permeabilidade e sólidos totais dissolvidos.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

During the period from October/92 to September/94 experiments were carried out at the Seed Laboratory, FCAV/UNESP, Jaboticabal, SP, Brazil, using soybean seeds of different genotypes in order to evaluate the effect of genotype on the electrical conductivity (bulk conductivity) of soaked seeds. Seed moisture content (105+/-3 degrees C, 24 h), standard germination (four 50-seed samples, paper towel, 30 degrees C), and vigor-accelerated aging (42 degrees C, 48 h) were first determined. Undamaged soybean seeds were soaked in deionized water (four 50-seed samples, 75 ml, 25 degrees C, 24 h) and electrical conductivity (mu mhos.cm(-1).g(-1)) was measured. Significant differences in conductivity were observed among genotypes having the same pattern of germination and vigor. The results have showed that electrical conductivity can be significantly influenced by genotype.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

This work presents an algorithm for the security control of electric power systems using control actions like generation reallocation, determined by sensitivity analysis (linearized model) and optimization by neural networks. The model is developed taking into account the dynamic network aspects. The preventive control methodology is developed by means of sensitivity analysis of the security margin related with the mechanical power of the system synchronous machines. The reallocation power in each machine is determined using neural networks. The neural network used in this work is of Hopfield type. These networks are dedicated electric circuits which simulate the constraint set and the objective function of an optimization problem. The advantage of using these networks is the higher speed in getting the solutions when compared to conventional optimization algorithms due to the great convergence rate of the process and the facility of the method parallelization. Then, the objectives are: formulate and investigate these networks implementations in determining. The generation reallocation in digital computers. Aiming to illustrate the proposed methodology an application considering a multi-machine system is presented.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The effects of salt concentration levels in electrical conductivity (EC) were evaluated in chrysanthemum root, cultivated in substrate using two sampling methods, under greenhouse conditions. The experiment was carried out in Paranapanema, São Paulo using the experimental design in randomized blocks and four replications. The treatments consisted of eight sampling periods of substrate solutions in pots: 7, 14, 21, 28, 35, 42, 49 and 56 days after strike root and five salt concentration levels of applied saline solution: 1.42; 1.65; 1.89; 2.13 and 2.36 dS m -1 in the vegetative period and during the reproduction period of flower budding: 1.71; 1.97; 2.28; 2.57 and 2.85 dS m -1. The substrate solution EC monitoring was done using two methods: solution extractors and 1:2 water diluted solution. The use of solution extractors and 1:2 water diluted solution allowed substrate solution EC monitoring along the culture cycle; the amount of salt concentration applied in the substrate caused the substrate salinity increase; the method using solution extractors presented higher EC values in the substrate.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Soil management measures that increase the efficiency of organic matter cycling and maintain favorable soil structure are needed for improving soil quality. On the other hand, soil structure degradation due to inadequate soil management systems is widespread. Among the indicators of soil physical quality, saturated hydraulic conductivity and penetration resistance are thought to be sensitive to soil management system. The aim of this work was to study the influence of soil tillage system and organic fertilization on selected soil physical properties after the first year of treatment. The field work was conducted in Selviria, MS, Brazil on an Oxisol. The experimental design was randomized complete blocks with split-plots, with 12 treatments and 4 repetitions. Tillage treatments included conventional ploughing (CT) and direct drilling (DD). Fertilizer treatments were: 1) manure, 2) manure plus mineral, 3) traditional mineral 4) plant residues of Crotalaria juncea, 5) plant residues of Pennisetum americanum and 6) control plot. The plots were cropped to bean in winter and to cotton in summer, and both cultures were irrigated. After one year no significant differences between treatments in mechanical resistance and porosity were found. However, saturated hydraulic conductivity and infiltration were higher in the conventional tillage treatment at the 0.00-0.10 m depth. Moreover, an improvement in soil physical condition by organic fertilizers was shown.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The study of growth and uptake of nutrients is important to determine the times of increased demand in order to schedule the fertigation. The present research was developed with the objective of evaluating the effects of different levels of electrical conductivity on growth and accumulation of nutrients in chrysanthemum plants under greenhouse conditions. The electrical conductivity levels on the applied solution were 1.42, 1.65, 1.89, 2.13 and 2.36 dS m-1 (bud vegetative stage); 1.71, 1.97, 2.28, 2.57 and 2.85 dS m-1 (bud stage). The dry mass of the aerial portion of the plant and the contents of macronutrients and micronutrients were determined every 14 days. The nutrient accumulation in chrysanthemum plant showed similar trend as compared to dry matter accumulation. The nutrients presented the following order of absorption: K>N>Ca>Mg>P>S (1425, 892, 184, 150, 110 and 59 mg plant-1) and Fe>Zn>B>Mn>Cu (2254, 2219, 1725, 1287, 210 μg plant-1). The content of most nutrients increased with increase in electrical conductivity of the solution, without salt effect up to EC of 2.85 dS m-1.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)