Influence of iodine value on combustion and NOx emission characteristics of a DI diesel engine

Biodiesel is a renewable fuel that has been shown to reduce many exhaust emissions, except oxides of nitrogen (NOx), in diesel engine cars. This is of special concern in inner urban areas that are subject to strict environmental regulations, such as EURO norms. Also, the use of pure biodiesel (B100) is inhibited because of its higher NOx emissions compared to petroleum diesel fuel. The aim of this present work is to investigate the effect of the iodine value and cetane number of various biodiesel fuels obtained from different feed stocks on the combustion and NOx emission characteristics of a direct injection (DI) diesel engine. The biodiesel fuels were chosen from various feed stocks such as coconut, palm kernel, mahua (Madhuca indica), pongamia pinnata, jatropha curcas, rice bran, and sesame seed oils. The experimental results show an approximately linear relationship between iodine value and NOx emissions. The biodiesels obtained from coconut and palm kernel showed lower NOx levels than diesel, but other biodiesels showed an increase in NOx. It was observed that the nature of the fatty acids of the biodiesel fuels had a significant influence on the NOx emissions. Also, the cetane numbers of the biodiesel fuels are affected both premixed combustion and the combustion rate, which further affected the amount of NOx formation. It was concluded that NOx emissions are influenced by many parameters of biodiesel fuels, particularly the iodine value and cetane number.

AC/DC electrical characteristics of epoxy-multi wall carbon nanotube nanocomposites

Expoxy nanocomposites with multiwell carbon nanotubes (mwcnts) filler up to 0.3%wt were prepared by sheer mixing and good dispersion of the MWCNTS in the epoxy was successfully achieved. The electrical behaviour was characterized by measurements of the alternating current (ac) and direct current (dc) conductives at room temperature. Typical percolation behaviour was observed at a low percolation threshold of 0.055%. Frequency independent ac conductivity was observed at low frequencies but not at high frequencies. An equivalent circuit models was used to predict the impedence response in these nanocomposites.

Lateral shearing interferometry, dynamic wavefront sensing, and high-speed videokeratoscopy for noninvasive assessment of tear film surface characteristics : a comparitive study

There are several noninvasive techniques for assessing the kinetics of tear film, but no comparative studies have been conducted to evaluate their efficacies. Our aim is to test and compare techniques based on high-speed videokeratoscopy (HSV), dynamic wavefront sensing (DWS), and lateral shearing interferometry (LSI). Algorithms are developed to estimate the tear film build-up time TBLD, and the average tear film surface quality in the stable phase of the interblink interval TFSQAv. Moderate but significant correlations are found between TBLD measured with LSI and DWS based on vertical coma (Pearson's r2=0.34, p<0.01) and higher order rms (r2=0.31, p<0.01), as well as between TFSQAv measured with LSI and HSV (r2=0.35, p<0.01), and between LSI and DWS based on the rms fit error (r2=0.40, p<0.01). No significant correlation is found between HSV and DWS. All three techniques estimate tear film build-up time to be below 2.5 sec, and they achieve a remarkably close median value of 0.7 sec. HSV appears to be the most precise method for measuring tear film surface quality. LSI appears to be the most sensitive method for analyzing tear film build-up.

Phenothiazine UVA dosimeter : characteristics and performance

This paper provides an overview of the characteristics of a phenothiazine-mylar dosimeter which can be used as an effective solar UVA exposure assessment tool. This dosimeter is sensitive to UVA wavelengths (315–400 nm); its performance has been characterized in a series of tests such as (a) UVA exposure response (dose-response), (b) temperature stability of the response, (c) impact of long term storage, and (d) angular response. There is no effect of long term storage post-exposure and no effect of temperature up to 30 °C. For angles up to 70°, the cosine error of the normalized UVA is less than approximately 0.1. These characterizations have confirmed the reliability and reproducibility of a phenothiazine-mylar combined dosimeter as an effective solar UVA exposure tool for field-based studies of the UVA exposures to population groups.

Biomass burning influenced particles characteristics in Northern Territory Australia based on airborne measurements

Airborne measurements of particle number concentrations from biomass burning were conducted in the Northern Territory, Australia, during June and September campaigns in 2003, which is the early and the late dry season in that region. The airborne measurements were performed along horizontal flight tracks, at several heights in order to gain insight into the particle concentration levels and their variation with height within the lower boundary layer (LBL), upper boundary layer (UBL), and also in the free troposphere (FT). The measurements found that the concentration of particles during the early dry season was lower than that for the late dry season. For the June campaign, the concentration of particles in LBL, UBL, and FT were (685 ± 245) particles/cm3, (365 ± 183) particles/cm3, and (495 ± 45) particle/cm3 respectively. For the September campaign, the concentration of particles were found to be (1233 ± 274) particles/cm3 in the LBL, (651 ± 68) particles/cm3 in the UBL, and (568 ± 70) particles/cm3 in the FT. The particle size distribution measurements indicate that during the late dry season there was no change in the particle size distribution below (LBL) and above the boundary layer (UBL). This indicates that there was possibly some penetration of biomass burning particles into the upper boundary layer. In the free troposphere the particle concentration and size measured during both campaigns were approximately the same.

Damage localisation in beams and plates using vibration characteristics

Dynamic computer simulation techniques are used to develop and apply a multi-criteria procedure, incorporating changes in natural frequencies, modal flexibility and the modal strain energy, for damage localisation in beams and plates. Numerically simulated modal data obtained through finite element analyses are used to develop algorithms based on changes of modal flexibility and modal strain energy before and after damage and used as the indices for assessment of the state of structural health. The proposed procedure is illustrated through its application to flexural members under different damage scenarios and the results confirm its feasibility for damage assessment.

User characteristics of transit oriented developments : the case of Kelvin Grove Urban Village

Transit oriented developments are high density mixed use developments located within short and easily walkable distance of a major transit centre. These developments are often hypothesised as a means of enticing a mode shift from the private car to sustainable transport modes such as, walking, cycling and public transport. However, it is important to gather evidence to test this hypothesis by determining the travel characteristics of transit oriented developments users. For this purpose, travel surveys were conducted for an urban transit oriented development currently under development. This chapter presents the findings from the preliminary data analysis of the travel surveys. Kelvin Grove Urban Village, a mixed use development located in Brisbane, Australia, has been selected as the case for the transit oriented developments study. Travel data for all groups of transit oriented development users ranging from students to shoppers, and residents to employees were collected. Different survey instruments were used for different transit oriented development users to optimise their response rates, and the performance of these survey instruments are stated herein. The travel characteristics of transit oriented development users are reported in this chapter by explaining mode share, trip length distribution, and time of day of trip. The results of the travel survey reveal that Kelvin Grove Urban Village users use more sustainable modes of transport as compared to other Brisbane residents.

Self-service technology and the moderating effects of consumer characteristics

The incidence of self-service technology, where the consumer delivers the service themselves using technology, is increasing in the service encounter. One area that is under-explored is the potential impact of self-service technology on consumer satisfaction and affective commitment. Accordingly, this paper presents an empirical study that investigates the relative impact of self-service technology on consumer satisfaction (both overall and transaction-specific) and affective commitment, accounting for the moderating effects of consumer characteristics. The results highlight the importance of personal service for evaluations of satisfaction and commitment, and the importance of social competency as a moderator in this relationship. An understanding of these consumer perceptions will allow organisations to develop strategies to deliver the services expected by their consumers, improving consumer satisfaction and commitment.

The impacts of traffic and rainfall characteristics on heavy metals build-up and wash-off from urban roads

An investigation into the effects of changes in urban traffic characteristics due to rapid urbanisation and the predicted changes in rainfall characteristics due to climate change on the build-up and wash-off of heavy metals was carried out in Gold Coast, Australia. The study sites encompassed three different urban land uses. Nine heavy metals commonly associated with traffic emissions were selected. The results were interpreted using multivariate data analysis and decision making tools, such as principal component analysis (PCA), fuzzy clustering (FC), PROMETHEE and GAIA. Initial analyses established high, low and moderate traffic scenarios as well as low, low to moderate, moderate, high and extreme rainfall scenarios for build-up and wash-off investigations. GAIA analyses established that moderate to high traffic scenarios could affect the build-up while moderate to high rainfall scenarios could affect the wash-off of heavy metals under changed conditions. However, in wash-off, metal concentrations in 1-75µm fraction were found to be independent of the changes to rainfall characteristics. In build-up, high traffic activities in commercial and industrial areas influenced the accumulation of heavy metal concentrations in particulate size range from 75 - >300 µm, whereas metal concentrations in finer size range of <1-75 µm were not affected. As practical implications, solids <1 µm and organic matter from 1 - >300 µm can be targeted for removal of Ni, Cu, Pb, Cd, Cr and Zn from build-up whilst organic matter from <1 - >300 µm can be targeted for removal of Cd, Cr, Pb and Ni from wash-off. Cu and Zn need to be removed as free ions from most fractions in wash-off.

The impact of managers' characteristics on the use of public relations strategy : an exploratory study in Queensland schools

While previous positive and normative studies have focused on the role public relations should play in organisations and the need for management in all organisations to attend to public relations (Cutlip et al., 2006), there has been little discussion in the public relations literature on why or how managers choose to enact public relations strategies for their organisations. If the discipline of public relations is to cement itself as a management function, then researchers must gain a better understanding of managers themselves given that they are the ones who decide if and how public relations strategies should be employed in the organisation. This study has sought to explore evidence of a relationship between management characteristics and their impact on decisions managers make when choosing which public relations strategies to adopt in response to changes in the organisation’s operating environment. This exploratory research study has been conducted within a specific context of schools in Queensland, Australia. Queensland schools have been facing a number of changes within their operating environment due to changes in Federal funding models in Australia’s education system. This study used an exploratory, qualitative approach to understand the management characteristics demonstrated by managers in schools and how these have impacted on the selection of public relations strategies for responding to their changing and increasingly competitive environment. The unit of analysis for this research study was principals in State (government) schools and in non-government schools. Ten principals were interviewed from four different types of schools in Queensland – the more traditional, elite, private schools (GPS Schools); other Independent Schools; Catholic Schools; and State (or public) schools. These interviews were analysed for quantitative comparisons of the managers’ characteristics across the different schools (in terms of the number of principals in each age bracket, those holding postgraduate qualifications, years of experience etc.); and for qualitative data to provide a greater sense of their understanding of public relations. The 10 schools were selected within a geographic area from Brisbane’s inner city to its outer western suburbs to include an element of competition amongst those managers being interviewed. A detailed review of government, school and other public documents was also conducted to gain an insight into the environment in which principals made decisions about public relations strategy to respond to increasing competition. This study found support for the literature on the relationship between management characteristics and strategy. However, there was also variation in findings warranting further investigation of the literature on the relationship between management characteristics and strategy in a school setting. Key relationships found in this study were between: management characteristics themselves; age and the use of public relations strategies; and gender and the use of public relations strategies. There was also evidence of support for the literature linking the impact that the combination of managers’ age, education and experience had on the use of public relations strategies. While this study was exploratory in nature, it did reveal a number of areas that require further investigation to gain a deeper understanding of how and why managers choose public relations strategies as a response to changes in their operating environment. It also provided a different framework to gain a better understanding of managers’ understanding and support of public relations in schools, which, in conjunction with an analysis of their management characteristics, will hopefully allow public relations scholars and practitioners alike gain an understanding of how and why managers use public relations strategies.

Driver distractions: Characteristics underlying drivers' risk perceptions

Driver distraction is a research area that continues to receive considerable research interest but the drivers’ perspective is less well documented. The current research focuses on how drivers perceive the risks associated with a range of driver distractions with the aim of identifying features that contribute to their risk perception judgements. Multidimensional scaling analysis was employed to better understand drivers’ risk perceptions for 15 in-vehicle and external distractions. Results identify both salient qualitative characteristics that underpin drivers’ risk perceptions, such as the probability of a crash, as well as identify other features inherent in the distractions that may also contribute to risk perceptions. The implications of the results are discussed for better understanding drivers’ perceptions of distractions and the potential for improving road safety messages related to distracted driving.

Export decisions within Taiwanese electrical and electronic SMEs : the role of management characteristics and attitudes

In this globalized environment, Taiwanese firms have been very successful in achieving growth via international market expansion. In particular, the Taiwanese electronics industry has shown a dynamism lacking in comparable industries around the world. However, in recent years there has been a move by many of the larger Taiwanese manufacturing firms to outsource their manufacturing to low-cost producers such as China in order to remain competitive. Conversely, most Taiwanese small- to medium-sized enterprises (SMEs) have retained their production facilities in Taiwan. These SMEs seek to expand their sales beyond the domestic market by employing an export strategy, making a significant socioeconomic contribution to the domestic and regional economies. This paper highlights the key dimensions such as enhancing factors (benefits/advantages), inhibiting factors (barriers/costs), and managerial factors (characteristics/commitment) that play an important role in the internationalization of SMEs located within the Taiwanese electronics industry. A logistic regression model is used to predict the probability of a firm being an exporter.

The prevalence and characteristics of self-reported dangerous driving behaviours among a young cohort

Background: Young motorists engaging in anti-social and often dangerous driving manoeuvres (which is often referred to as “hooning” within Australia) is an increasing road safety problem. While anecdotal evidence suggests that such behaviour is positively linked with crash involvement, researchers have yet to examine whether younger drivers who deliberately break road rules and drive in an erratic manner (usually with peers) are in fact over represented in crash statistics. This paper outlines research that aimed to identify the characteristics of individuals most likely to engaging in hooning behaviours, as well as examine the frequency of such driving behaviours and if such activity is linked with self-reported crash involvement.---------- Methods: A total of 717 young drivers in Queensland voluntarily completed a questionnaire to investigate their driving behaviour and crash history.---------- Results: Quantitative analysis of the data revealed that almost half the sample reported engaging in some form of “hooning” behaviour at least once in their lifetime, although only 4% indicated heavy participation in the behaviour e.g., >50 times. Street racing was the most common activity reported by participants followed by “drifting” and then “burnouts”. Logistic regression analysis indicated that being younger and a male was predictive of reporting such anti-social driving behaviours, and importantly, a trend was identified between such behaviour and self-reported crash involvement.---------- Conclusions: This research provides preliminary evidence that younger male drivers are more likely to engage in dangerous driving behaviours, which ultimately may prove to increase their overall risk of becoming involved in a crash. This paper will further outline the study findings in regards to current enforcement efforts to deter such driving activity as well as provide direction for future research efforts in this area.---------- Research highlights: ► The self-reported driving behaviours of 717 younger Queensland drivers were examined to investigate the relationship between deliberately breaking road rules and self-reported crash involvement. ► Younger male drivers were most likely to engage in such aberrant driving behaviours and a trend was identified between such behaviour and self-reported crash involvement.

The impact of contractor’s characteristics in gauging level satisfaction

The outcomes of the construction projects can be evaluated in numerous ways. One method is to measure the satisfaction of participants as represented by the differences between their expectations and perceptions. This measurement is used widely in construction as it promises benefits, such as the improvement of product delivery, and enhances services quality by identifying some necessary changes. Commonly satisfaction measurement is gauged by evaluating the level of client satisfaction of construction performance. The measurement of customer satisfaction on the other hand, is based on the quality of the end product. This evaluation is used to encourage contractors to improve their performance to a required level and to ensure that the projects are delivered as expected- in terms of time, budget and quality. Several studies of performance measurement have indicated that contractor performance is still not satisfactory, as the outcome delivered is not as required (because of cost overruns, time overruns or because it is generally unsatisfactory). This drawback may be due to the contractors’ lack of expertise, motivation and/or satisfaction. The measurement of performance based on contractor satisfaction levels is still new and very few studies have yet taken place in the construction industry. This paper examines how the characteristics of a contracting organisation – namely its experience in the industry, background, past performance, size of organisation and financial stability- may influence its satisfaction levels with regards to project performance. Previous literature reviews and interviews are used as research tools in the preliminary investigation. The outcome is expected to present a basic understanding of contractor satisfaction measurement and its potential for improving the performance of project outcomes.

The effects of content presentation format and user characteristics on novice developers’ understanding of process models

Process models are used by information professionals to convey semantics about the business operations in a real world domain intended to be supported by an information system. The understandability of these models is vital to them being used for information systems development. In this paper, we examine two factors that we predict will influence the understanding of a business process that novice developers obtain from a corresponding process model: the content presentation form chosen to articulate the business domain, and the user characteristics of the novice developers working with the model. Our experimental study provides evidence that novice developers obtain similar levels of understanding when confronted with an unfamiliar or a familiar process model. However, previous modeling experience, the use of English as a second language, and previous work experience in BPM are important influencing factors of model understanding. Our findings suggest that education and research in process modeling should increase the focus on human factors and how they relate to content and content presentation formats for different modeling tasks. We discuss implications for practice and research.