Tailoring the Structural Properties of PVDF and P(VDF-TrFE) by Using Natural Polymers as Additives

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Phytogenic additives and organic acids in broiler chicken diets

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Performance, carcass characteristics and gain cost of feedlot cattle fed a high level of concentrate and different feed additives

The objective of this study was to evaluate the effects of feeding cattle with isoprotein and isoenergetic diets, with and without the addition of polyclonal antibody preparation (PAP), yeasts (YST) or monensin sodium (MON) on performance, carcass characteristics and gain cost in feedlot. Ninety-five 20-month old bullocks (323.3±21.8 kg) were distributed in 25 pens. The completely randomized experimental design had a 2 × 2 + 1 factorial arrangement and the treatments were replicated 5 times. There was no effect of MON for DMI throughout the feedlot period; however, MON reduced the dry matter intake (DMI) in g/kg of BW in the first 28 days when compared with the other treatments. The gain cost decreased with MON addition in relation to the other treatments. Inclusion of YST decreased average daily gain (ADG), final body weight, hot carcass weight, carcass weight, gain to feed ratio and DMI in g/kg body weight, worsening feed conversion and increasing the gain cost in the feeding periods. Inclusion of PAP increased ADG and decreased the gain cost, besides improving feed conversion. For MON and PAP, a difference was found for kidney-pelvic fat and kidney-pelvic fat per 100 kg of hot carcass weight. For MON and YST, there was a difference in ADG, feed conversion, gain cost and carcass yield and kidney-pelvic fat per 100 kg of hot carcass. Treatment YST worsened performance in relation to the non-supplemented treatments. Feeding PAP to animals did not influence performance and carcass characteristics of bullocks in feedlot negatively. Thus, PAP shows potential to substitute MON in cattle feeding using isoprotein and isoenergetic diets.

Effects of organic and inorganic additives on flotation recovery of washed cells of Saccharomyces cerevisiae resuspended in water

Separation of microbial cells by flotation recovery is usually carried out in industrial reactors or wastewater treatment systems, which contain a complex mixture of microbial nutrients and excretion products. In the present study, the separation of yeast cells by flotation recovery was carried out using a simple flotation recovery systems containing washed yeast cells resuspended in water in order to elucidate the effects of additives (defined amounts of organic and inorganic acids, ethanol, surfactants and sodium chloride) on the cellular interactions at interfaces (cell/aqueous phase and cell/air bubble). When sodium chloride, organic acids (notably propionic, succinic and acetic acids) and organic surfactants (sodium dodecyl sulphate (SDS), cetyltrimethylammonium bromide (CTAB) and Nonidet P40) were added to the flotation recovery system, significant increases in the cell recovery of yeast hydrophobic cells (Saccharomyces cerevisiae, strain FLT-01) were observed. The association of ethanol to acetic acid solution (a minor by-product of alcoholic fermentation) in the flotation recovery system, containing washed cells of strain FLT-01 resuspended in water, leading to an increased flotation recovery at pH 5.5. Thus, the association among products of the cellular metabolism (e.g., ethanol and acetic acid) can improve yeast cell recovery by flotation recovery. (c) 2006 Elsevier B.V. All rights reserved.

Fermentation, losses, and aerobic stability of sugarcane silages treated with chemical or bacterial additives

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Water adsorption isotherms and isosteric sorption heat of spray-dried and freeze-dried dehydrated passion fruit pulp with additives and skimmed milk

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Si3N4 ceramic cutting tool sintered with CeO2 and Al2O3 additives with AlCrN coating

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sugarcane silage production treated with additives at different times post burning

Objetivou-se estudar a ação do tempo após a queima do canavial e o uso de aditivos sobre as características fermentativas, as perdas e a composição química de silagens de cana-de-açúcar. A cultivar utilizada foi a IAC 86-2480 colhida em cinco tempos (1, 4, 7, 10 e 14 dias) pós-queima. Os aditivos utilizados foram controle, sem aditivos, Lactobacillus buchneri, cal virgem micropulverizada e Lactobacillus buchneri + cal virgem micropulverizada. Antes da ensilagem em cada tempo, foram determinadas as populações de leveduras presentes na cana-de-açúcar. Decorridos 56 dias após a ensilagem, os silos experimentais foram abertos. O delineamento experimental utilizado foi o inteiramente casualizado em esquema fatorial, considerando os fatores aditivos e tempo pós-queima. Houve recontaminação da cana-de-açúcar pelas leveduras, elevando a população de 5,04 para 6,48 log ufc/g de forragem. Os teores de matéria seca (MS) após a abertura do silo reduziram em média 7,6 unidades percentuais em comparação aos observados na ensilagem. As silagens controle e com Lactobacillus buchneri tiveram menores recuperações da matéria seca (613 e 631 g/kg, respectivamente), em comparação às observadas nas silagens com cal e com a combinação Lactobacillus buchneri + cal (807 g/kg e 832 g/kg, respectivamente), fato que pode ser justificado pelo controle de levedura pela cal. Após a queima, as maiores variações foram na produção de gás e na recuperação de matéria seca: a produção de gás foi maior nos primeiros dias e diminuiu com o tempo após a queima, consequentemente, a recuperação de MS foi menor nos primeiros dias e aumentou com o tempo após a queima. O tempo após a queima altera o valor nutritivo da cana-de-açúcar fresca e das suas silagens, assim como a magnitude das perdas no processo de ensilagem.

Mechanical properties, hydrophilicity and water activity of starch-gum film: effect of additives and deacetylated xanthan gum

The effect of deacetylated xanthan gum, additives (sucrose, soybean oil, sodium phosphate and propylene glycol) and pH modifications on mechanical properties, hydrophilicity and water activity of cassava starch-xanthan gum films has been studied. Sucrose addition resulted in the highest effect observed on cassava starch films elongation at break. The deacetylated xanthan gum had higher effect on elongation at break when comparing to the acetylated gum, although both gums presented an inferior effect in relation to the obtained with sucrose. However, when comparing to the control and PVC films, lower tensile strength resistance values were observed when adding sucrose. Increased water activity was observed for films added with sucrose, thus, increasing the material biodegradation. Sucrose and deacetylated xanthan gum addition resulted in a slight hydrophilicity increase. (C) 2004 Elsevier Ltd. All rights reserved.

Structural effects of Li and K additives on the columbite precursor and 0.9PMN-0.1PT powders

Single-phase perovskite 0.9Pb(Mg1/3Nb2/3)O-3-0.1PbTiO(3) (PMN-PT) powders were prepared by using a Ti-modified columbite precursor (MNT) obtained by the polymeric precursor method. The innovation consists in the preparation of Ti-modified columbite in order to react directly with a stoichiometric amount of PbO to obtain pyrochlore-free PMN-PT powders. It has been shown that titanium oxide forms a solid solution with columbite (MN) and does not affect the obtaining of a single-phase columbite precursor. Thus, a high amount of perovskite phase can be obtained by reaction with PbO at 800 degreesC for 2 h. Effects of K and Li additives on the structure of MNT and PMN-PT were studied. X-ray diffraction studies were carried out to verify the phase formation at each processing step and these data were used for structural refinement by the Rietveld method. Both K and Li additives increase the crystallinity of MNT powders, being this effect more intense for the Li-doped samples. For PMN-PT samples the additives cause an insignificant decrease in the amount of perovskite phase. The morphology of the PMN-PT powder depends on the type of the additive. (C) 2003 Elsevier B.V All rights reserved.

Evaluation of the influences of solution path length and additives concentrations on the solar photo-Fenton degradation of 4-chlorophenol using multivariate analysis

This study reports the photodegradation of 4-chlorophenol (4-CP) in aqueous solution by the photo-Fenton process using solar irradiation. The influence of solution path length, and Fe(NO3)(3) and H2O2 concentrations on the degradation of 4-CP is evaluated by response surface methodology. The degradation process was monitored by the removal of total organic carbon (TOC) and the release of chloride ion. The results showed a very important role of iron concentration either for TOC removal or dechlorination. on the other hand, a negative effect of increasing solution path length on mineralization was observed, which can be compensated by increasing the iron concentration. This permits an adjustment of the iron concentration according to the irradiation exposure area and path length (depth of a tank reactor). Under optimum conditions of 1.5 mM Fe(NO3)(3), 20.0 mM H2O2 and 4.5 cm solution path length, 17 min irradiation under solar light were sufficient to reduce a 72 mg C L-1 solution of 4-CP by 91 (c) 2006 Elsevier B.V. All rights reserved.

Effect of additives and powder preparation techniques on PTCR properties of barium titanate

PTCR barium titanate has been prepared following two different powder preparation techniques: the solid-state reaction route and co-precipitation route for the comparison of results. The co-precipitation route produces better PTCR characteristics with low room temperature resistivity and better reproducibility of prepared samples. The effects of different concentrations of additives like donors, acceptors and excess titanium have been optimized to get good quality PTCR samples. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Spray Nozzles, Pressures, Additives and Stirring Time on Viability and Pathogenicity of Entomopathogenic Nematodes (Nematoda: Rhabditida) for Greenhouses

The objective of this study was to evaluate different strategies for the application of entomopathogenic nematodes (EPN). Three different models of spray nozzles with air induction (AI 11003, TTI 11003 and AD-IA 11004), three spray pressures (207, 413 and 720 kPa), four different additives for tank mixtures (cane molasses, mineral oil, vegetable oil and glycerin) and the influence of tank mixture stirring time were all evaluated for their effect on EPN (Steinernema feltiae) viability and pathogenicity. The different nozzles, at pressures of up to 620 kPa, were found to be compatible with S. feltiae. Vegetable oil, mineral oil and molasses were found to be compatible adjuvants for S. feltiae, and stirring in a motorized backpack sprayer for 30 minutes did not impact the viability or pathogenicity of this nematode. Appropriate techniques for the application of nematodes with backpack sprayers are discussed. © 2013 Moreira et al.

Corn silage inoculated with microbial additives

Pós-graduação em Zootecnia - FCAV