Numerical exploration of plastic deformation mechanisms of copper nanowires with surface defects

Based on the molecular dynamics simulation, plastic deformation mechanisms associated with the zigzag stress curves in perfect and surface defected copper nanowires under uniaxial tension are studied. In our previous study, it has found that the surface defect exerts larger influence than the centro-plane defect, and the 45o surface defect appears as the most influential surface defect. Hence, in this paper, the nanowire with a 45o surface defect is chosen to investigate the defect’s effect to the plastic deformation mechanism of nanowires. We find that during the plastic deformation of both perfect and defected nanowires, decrease regions of the stress curve are accompanied with stacking faults generation and migration activities, but during stress increase, the structure of the nanowire appears almost unchanged. We also observe that surface defects have obvious influence on the nanowire’s plastic deformation mechanisms. In particular, only two sets of slip planes are found to be active and twins are also observed in the defected nanowire.

Corporate governance mechanisms and earnings management in transitional countries – evidence from Chinese listed firms

The objective of this thesis is to investigate whether the corporate governance practices adopted by Chinese listed firms are associated with the quality of earnings information. Based on a review of agency and institutional theory, this study develops hypotheses that predict the monitoring effectiveness of the board and the audit committee. Using a combination of univariate and multivariate analyses, the association between corporate governance mechanisms and earnings management are tested from 2004 to 2008. Through analysing the empirical results, a number of findings are summarised as below. First, board independence is weakened by the introduction of government officials as independent directors on the boards. Government officials acting as independent directors, claim that they meet the definition of independent director set by the regulation. However, they have some connection with the State, which is the controlling shareholder in listed SOEs affiliated companies. Consequently, the effect of the independent director’s expertise in constraining earnings management is mitigated as demonstrated by an insignificant association between board expertise and earnings management. An alternative explanation for the inefficiency of board independence may point to the pre-selection of independent directors by the powerful CEO. It is argued that a CEO can manipulate the board composition and choose the "desirable" independent directors to monitor themselves. Second, a number of internal mechanisms, such as board size, board activities, and the separation of the roles of the CEO and chair are found to be significantly associated with discretionary accruals. This result suggests that there are advantages in having a large and active board in the Chinese setting. This can offset the disadvantages associated with large boards, such as increased bureaucracy, and hence, increase the constraining effects of a large and resourceful board. Third, factor analysis identifies two factors: CEO power and board power. CEO power is the factor which consists of CEO duality and turnover, and board power is composed of board size and board activity. The results of CEO power show that if a Chinese listed company has CEO duality and turnover at the same time, it is more likely to have a high level of earnings management. The significant and negative relationship between board power and accruals indicate that large boards with frequent meetings can be associated with low level of earnings management. Overall, the factor analysis suggests that certain governance mechanisms complement each other to become more efficient monitors of opportunistic earnings management. A combination of board characteristics can increase the negative association with earnings management. Fourth, the insignificant results between audit committees and earnings management in Chinese listed firms suggests that the Chinese regulator should strengthen the audit committee functions. This thesis calls for listed firms to disclose more information on audit committee composition and activities, which can facilitate future research on the Chinese audit committee’s monitoring role. Fifth, the interactive results between State ownership and board characteristics show that dominant State ownership has a moderating effect on board monitoring power as the State totally controls 42% of the issued shares. The high percentage of State ownership makes it difficult for the non-controlling institutional shareholders to challenge the State’s dominant status. As a result, the association between non-controlling institutional ownership and earnings management is insignificant in most situations. Lastly, firms audited by the international Big4 have lower abnormal accruals than firms audited by domestic Chinese audit firms. In addition, the inverse U-shape relationship between audit tenure and earnings quality demonstrates the changing effects of audit quality after a certain period of appointment. Furthermore, this thesis finds that listing in Hong Kong Stock Exchanges can be an alternative governance mechanism to discipline Chinese firms to follow strict Hong Kong listing requirements. Management of Hong Kong listed companies are exposed to the scrutiny of international investors and Hong Kong regulators. This in turn reduces their chances of conducting self-interested earnings manipulation. This study is designed to fill the gap in governance literature in China that is related to earnings management. Previous research on corporate governance mechanisms and earnings management in China is not conclusive. The current research builds on previous literature and provides some meaningful implications for practitioners, regulators, academic, and international investors who have investment interests in a transitional country. The findings of this study contribute to corporate governance and earnings management literature in the context of the transitional economy of China. The use of alternative measures for earnings management yields similar results compared with the accruals models and produces additional findings.

Deformation behaviours of coarse-grained and nanocrystalline Mg-5wt% Al alloys

Magnesium alloys have been of growing interest to various engineering applications, such as the automobile, aerospace, communication and computer industries due to their low density, high specific strength, good machineability and availability as compared with other structural materials. However, most Mg alloys suffer from poor plasticity due to their Hexagonal Close Packed structure. Grain refinement has been proved to be an effective method to enhance the strength and alter the ductility of the materials. Several methods have been proposed to produce materials with nanocrystalline grain structures. So far, most of the research work on nanocrystalline materials has been carried out on Face-Centered Cubic and Body-Centered Cubic metals. However, there has been little investigation of nanocrystalline Mg alloys. In this study, bulk coarse-grained and nanocrystalline Mg alloys were fabricated by a mechanical alloying method. The mixed powder of Mg chips and Al powder was mechanically milled under argon atmosphere for different durations of 0 hours (MA0), 10 hours (MA10), 20 hours (MA20), 30 hours (MA30) and 40 hours (MA40), followed by compaction and sintering. Then the sintered billets were hot-extruded into metallic rods with a 7 mm diameter. The obtained Mg alloys have a nominal composition of Mg–5wt% Al, with grain sizes ranging from 13 μm down to 50 nm, depending on the milling durations. The microstructure characterization and evolution after deformation were carried out by means of Optical microscopy, X-Ray Diffraction, Scanning Electron Microscopy, Transmission Electron Microscopy, Scanning Probe Microscopy and Neutron Diffraction techniques. Nanoindentaion, compression and micro-compression tests on micro-pillars were used to study the size effects on the mechanical behaviour of the Mg alloys. Two kinds of size effects on the mechanical behaviours and deformation mechanisms were investigated: grain size effect and sample size effect. The nanoindentation tests were composed of constant strain rate, constant loading rate and indentation creep tests. The normally reported indentation size effect in single crystal and coarse-grained crystals was observed in both the coarse-grained and nanocrystalline Mg alloys. Since the indentation size effect is correlated to the Geometrically Necessary Dislocations under the indenter to accommodate the plastic deformation, the good agreement between the experimental results and the Indentation Size Effect model indicated that, in the current nanocrystalline MA20 and MA30, the dislocation plasticity was still the dominant deformation mechanism. Significant hardness enhancement with decreasing grain size, down to 58 nm, was found in the nanocrystalline Mg alloys. Further reduction of grain size would lead to a drop in the hardness values. The failure of grain refinement strengthening with the relatively high strain rate sensitivity of nanocrystalline Mg alloys suggested a change in the deformation mechanism. Indentation creep tests showed that the stress exponent was dependent on the loading rate during the loading section of the indentation, which was related to the dislocation structures before the creep starts. The influence of grain size on the mechanical behaviour and strength of extruded coarse-grained and nanocrystalline Mg alloys were investigated using uniaxial compression tests. The macroscopic response of the Mg alloys transited from strain hardening to strain softening behaviour, with grain size reduced from 13 ìm to 50 nm. The strain hardening was related to the twinning induced hardening and dislocation hardening effect, while the strain softening was attributed to the localized deformation in the nanocrystalline grains. The tension–compression yield asymmetry was noticed in the nanocrystalline region, demonstrating the twinning effect in the ultra-fine-grained and nanocrystalline region. The relationship k tensions < k compression failed in the nanocrystalline Mg alloys; this was attributed to the twofold effect of grain size on twinning. The nanocrystalline Mg alloys were found to exhibit increased strain rate sensitivity with decreasing grain size, with strain rate ranging from 0.0001/s to 0.01/s. Strain rate sensitivity of coarse-grained MA0 was increased by more than 10 times in MA40. The Hall-Petch relationship broke down at a critical grain size in the nanocrystalline region. The breakdown of the Hall-Petch relationship and the increased strain rate sensitivity were due to the localized dislocation activities (generalization and annihilation at grain boundaries) and the more significant contribution from grain boundary mediated mechanisms. In the micro-compression tests, the sample size effects on the mechanical behaviours were studied on MA0, MA20 and MA40 micro-pillars. In contrast to the bulk samples under compression, the stress-strain curves of MA0 and MA20 micro-pillars were characterized with a number of discrete strain burst events separated by nearly elastic strain segments. Unlike MA0 and MA20, the stress-strain curves of MA40 micro-pillars were smooth, without obvious strain bursts. The deformation mechanisms of the MA0 and MA20 micro-pillars under micro-compression tests were considered to be initially dominated by deformation twinning, followed by dislocation mechanisms. For MA40 pillars, the deformation mechanisms were believed to be localized dislocation activities and grain boundary related mechanisms. The strain hardening behaviours of the micro-pillars suggested that the grain boundaries in the nanocrystalline micro-pillars would reduce the source (nucleation sources for twins/dislocations) starvation hardening effect. The power law relationship of the yield strength on pillar dimensions in MA0, MA20 supported the fact that the twinning mechanism was correlated to the pre-existing defects, which can promote the nucleation of the twins. Then, we provided a latitudinal comparison of the results and conclusions derived from the different techniques used for testing the coarse-grained and nanocrystalline Mg alloy; this helps to better understand the deformation mechanisms of the Mg alloys as a whole. At the end, we summarized the thesis and highlighted the conclusions, contributions, innovations and outcomes of the research. Finally, it outlined recommendations for future work.

Formation mechanisms of secondary organic aerosols in relation to laser printer emissions

Due to their large surface area, complex chemical composition and high alveolar deposition rate, ultrafine particles (UFPs) (< 0.1 ìm) pose a significant risk to human health and their toxicological effects have been acknowledged by the World Health Organisation. Since people spend most of their time indoors, there is a growing concern about the UFPs present in some indoor environments. Recent studies have shown that office machines, in particular laser printers, are a significant indoor source of UFPs. The majority of printer-generated UFPs are organic carbon and it is unlikely that these particles are emitted directly from the printer or its supplies (such as paper and toner powder). Thus, it was hypothesised that these UFPs are secondary organic aerosols (SOA). Considering the widespread use of printers and human exposure to these particles, understanding the processes involved in particle formation is of critical importance. However, few studies have investigated the nature (e.g. volatility, hygroscopicity, composition, size distribution and mixing state) and formation mechanisms of these particles. In order to address this gap in scientific knowledge, a comprehensive study including state-of-art instrumental methods was conducted to characterise the real-time emissions from modern commercial laser printers, including particles, volatile organic compounds (VOCs) and ozone (O3). The morphology, elemental composition, volatility and hygroscopicity of generated particles were also examined. The large set of experimental results was analysed and interpreted to provide insight into: (1) Emissions profiles of laser printers: The results showed that UFPs dominated the number concentrations of generated particles, with a quasi unimodal size distribution observed for all tests. These particles were volatile, non-hygroscopic and mixed both externally and internally. Particle microanalysis indicated that semi-volatile organic compounds occupied the dominant fraction of these particles, with only trace quantities of particles containing Ca and Fe. Furthermore, almost all laser printers tested in this study emitted measurable concentrations of VOCs and O3. A positive correlation between submicron particles and O3 concentrations, as well as a contrasting negative correlation between submicron particles and total VOC concentrations were observed during printing for all tests. These results proved that UFPs generated from laser printers are mainly SOAs. (2) Sources and precursors of generated particles: In order to identify the possible particle sources, particle formation potentials of both the printer components (e.g. fuser roller and lubricant oil) and supplies (e.g. paper and toner powder) were investigated using furnace tests. The VOCs emitted during the experiments were sampled and identified to provide information about particle precursors. The results suggested that all of the tested materials had the potential to generate particles upon heating. Nine unsaturated VOCs were identified from the emissions produced by paper and toner, which may contribute to the formation of UFPs through oxidation reactions with ozone. (3) Factors influencing the particle emission: The factors influencing particle emissions were also investigated by comparing two popular laser printers, one showing particle emissions three orders of magnitude higher than the other. The effects of toner coverage, printing history, type of paper and toner, and working temperature of the fuser roller on particle number emissions were examined. The results showed that the temperature of the fuser roller was a key factor driving the emission of particles. Based on the results for 30 different types of laser printers, a systematic positive correlation was observed between temperature and particle number emissions for printers that used the same heating technology and had a similar structure and fuser material. It was also found that temperature fluctuations were associated with intense bursts of particles and therefore, they may have impact on the particle emissions. Furthermore, the results indicated that the type of paper and toner powder contributed to particle emissions, while no apparent relationship was observed between toner coverage and levels of submicron particles. (4) Mechanisms of SOA formation, growth and ageing: The overall hypothesis that UFPs are formed by reactions with the VOCs and O3 emitted from laser printers was examined. The results proved this hypothesis and suggested that O3 may also play a role in particle ageing. In addition, knowledge about the mixing state of generated particles was utilised to explore the detailed processes of particle formation for different printing scenarios, including warm-up, normal printing, and printing without toner. The results indicated that polymerisation may have occurred on the surface of the generated particles to produce thermoplastic polymers, which may account for the expandable characteristics of some particles. Furthermore, toner and other particle residues on the idling belt from previous print jobs were a very clear contributing factor in the formation of laser printer-emitted particles. In summary, this study not only improves scientific understanding of the nature of printer-generated particles, but also provides significant insight into the formation and ageing mechanisms of SOAs in the indoor environment. The outcomes will also be beneficial to governments, industry and individuals.

The microRNA expression signature on modified titanium implant surfaces influences genetic mechanisms leading to osteogenic differentiation

Topographically and chemically modified titanium implants are recognized to have improved osteogenic properties; however, the molecular regulation of this process remains unknown. This study aimed to determine the microRNA profile and the potential regulation of osteogenic differentiation following early exposure of osteoprogenitor cells to sand-blasted, large-grit acid-etched (SLA) and hydrophilic SLA (modSLA) surfaces. Firstly, the osteogenic characteristics of the primary osteoprogenitor cells were confirmed using ALP activity and Alizarin Red S staining. The effect of smooth (SMO), SLA and modSLA surfaces on the TGF-β/BMP (BMP2, BMP6, ACVR1) and non-canonical WNT/Ca2+ (WNT5A, FZD6) pathways, as well as the integrins ITGB1 and ITGA2, was determined. It was revealed that the modified titanium surfaces could induce the activation of TGF-β/BMP and non-canonical WNT/Ca2+ signaling genes. The expression pattern of microRNAs (miRNAs) related to cell differentiation was evaluated. Statistical analysis of the differentially regulated miRNAs indicated that 35 and 32 miRNAs were down-regulated on the modSLA and SLA surfaces respectively, when compared with the smooth surface (SMO). Thirty-one miRNAs that were down-regulated were common to both modSLA and SLA. There were 10 miRNAs up-regulated on modSLA and nine on SLA surfaces, amongst which eight were the same as observed on modSLA. TargetScan predictions for the down-regulated miRNAs revealed genes of the TGF-β/BMP and non-canonical Ca2+ pathways as targets. This study demonstrated that modified titanium implant surfaces induce differential regulation of miRNAs, which potentially regulate the TGF-β/BMP and WNT/Ca2+ pathways during osteogenic differentiation on modified titanium implant surfaces.

The role of organisational culture, trust and mechanisms in inter-project knowledge sharing

Knowledge has been recognised as a powerful yet intangible asset, which is difficult to manage. This is especially true in a project environment where there is the potential to repeat mistakes, rather than learn from previous experiences. The literature in the project management field has recognised the importance of knowledge sharing (KS) within and between projects. However, studies in that field focus primarily on KS mechanisms including lessons learned (LL) and post project reviews as the source of knowledge for future projects, and only some preliminary research has been carried out on the aspects of project management offices (PMOs) and organisational culture (OC) in KS. This study undertook to investigate KS behaviours in an inter-project context, with a particular emphasis on the role of trust, OC and a range of knowledge sharing mechanisms (KSM) in achieving successful inter-project knowledge sharing (I-PKS). An extensive literature search resulted in the development of an I-PKS Framework, which defined the scope of the research and shaped its initial design. The literature review indicated that existing research relating to the three factors of OC, trust and KSM remains inadequate in its ability to fully explain the role of these contextual factors. In particular, the literature review identified these areas of interest: (1) the conflicting answers to some of the major questions related to KSM, (2) the limited empirical research on the role of different trust dimensions, (3) limited empirical evidence of the role of OC in KS, and (4) the insufficient research on KS in an inter-project context. The resulting Framework comprised the three main factors including: OC, trust and KSM, demonstrating a more integrated view of KS in the inter-project context. Accordingly, the aim of this research was to examine the relationships between these three factors and KS by investigating behaviours related to KS from the project managers‘ (PMs‘) perspective. In order to achieve the aim, this research sought to answer the following research questions: 1. How does organisational culture influence inter-project knowledge sharing? 2. How does the existence of three forms of trust — (i) ability, (ii) benevolence and (iii) integrity — influence inter-project knowledge sharing? 3. How can different knowledge sharing mechanisms (relational, project management tools and process, and technology) improve inter-project knowledge sharing behaviours? 4. How do the relationships between these three factors of organisational culture, trust and knowledge sharing mechanisms improve inter-project knowledge sharing? a. What are the relationships between the factors? b. What is the best fit for given cases to ensure more effective inter-project knowledge sharing? Using multiple case studies, this research was designed to build propositions emerging from cross-case data analysis. The four cases were chosen on the basis of theoretical sampling. All cases were large project-based organisations (PBOs), with a strong matrix-type structure, as per the typology proposed by the Project Management Body of Knowledge (PMBoK) (2008). Data were collected from project management departments of the respective organisations. A range of analytical techniques were used to deal with the data including pattern matching logic and explanation building analysis, complemented by the use of NVivo for data coding and management. Propositions generated at the end of the analyses were further compared with the extant literature, and practical implications based on the data and literature were suggested in order to improve I-PKS. Findings from this research conclude that OC, trust, and KSM contribute to inter-project knowledge sharing, and suggest the existence of relationships between these factors. In view of that, this research identified the relationships between different trust dimensions, suggesting that integrity trust reinforces the relationship between ability trust and knowledge sharing. Furthermore, this research demonstrated that characteristics of culture and trust interact to reinforce preferences for mechanisms of knowledge sharing. This means that cultures that facilitate characteristics of Clan type are more likely to result in trusting relationships, hence are more likely to use organic sources of knowledge for both tacit and explicit knowledge exchange. In contrast, cultures that are empirically driven, based on control, efficiency, and measures (characteristics of Hierarchy and Market types) display tendency to develop trust primarily in ability of non-organic sources, and therefore use these sources to share mainly explicit knowledge. This thesis contributes to the project management literature by providing a more integrative view of I-PKS, bringing the factors of OC, trust and KSM into the picture. A further contribution is related to the use of collaborative tools as a substitute for static LL databases and as a facilitator for tacit KS between geographically dispersed projects. This research adds to the literature on OC by providing rich empirical evidence of the relationships between OC and the willingness to share knowledge, and by providing empirical evidence that OC has an effect on trust; in doing so this research extends the theoretical propositions outlined by previous research. This study also extends the research on trust by identifying the relationships between different trust dimensions, suggesting that integrity trust reinforces the relationship between ability trust and KS. Finally, this research provides some directions for future studies.

IL-18 inhibits growth of murine orthotopic prostate carcinomas via both adaptive and innate immune mechanisms

Interleukin(IL)-18 is a pleiotrophic cytokine with functions in immune modulation, angiogenesis and bone metabolism. In this study, the potential of IL-18 as an immunotherapy for prostate cancer (PCa) was examined using the murine model of prostate carcinoma, RM1 and a bone metastatic variant RM1(BM)/B4H7-luc. RM1 and RM1(BM)/B4H7-luc cells were stably transfected to express bioactive IL-18. These cells were implanted into syngeneic immunocompetent mice, with or without an IL-18-neutralising antibody (αIL-18, SK113AE4). IL-18 significantly inhibited the growth of both subcutaneous and orthotopic RM1 tumors and the IL-18 neutralizing antibody abrogated the tumor growth-inhibition. In vivo neutralization of interferon-gamma (IFN-γ) completely eliminated the anti-tumor effects of IL-18 confirming an essential role of IFN-γ as a down-stream mediator of the anti-tumor activity of IL-18. Tumors from mice in which IL-18 and/or IFN-γ was neutralized contained significantly fewer CD4+ and CD8+ T cells than those with functional IL-18. The essential role of adaptive immunity was demonstrated as tumors grew more rapidly in RAG1−/− mice or in mice depleted of CD4+ and/or CD8+ cells than in normal mice. The tumors in RAG1−/− mice were also significantly smaller when IL-18 was present, indicating that innate immune mechanisms are involved. IL-18 also induced an increase in tumor infiltration of macrophages and neutrophils but not NK cells. In other experiments, direct injection of recombinant IL-18 into established tumors also inhibited tumor growth, which was associated with an increase in intratumoral macrophages, but not T cells. These results suggest that local IL-18 in the tumor environment can significantly potentiate anti-tumor immunity in the prostate and clearly demonstrate that this effect is mediated by innate and adaptive immune mechanisms.

Incentive mechanisms in infrastructure projects : A case-based comparison between Australia and the Netherlands

Despite a general belief that incentive mechanisms can improve value for money during procurement and performance during project execution, empirical research on the actual effects is nascent. This research focuses on the design and implementation of incentive mechanisms in four different infrastructure projects: two road reconstructions in the Netherlands and two building constructions in Australia. Based on an analytical framework of key motivation drivers, a cross cases analysis is conducted in view of performance on the contract assumptions, selection phase, execution phase and project contract performance. It was identified that despite significant differences in the project characteristics, results indicate that they experience similar contextual drivers on the incentive effectiveness. High value was placed on risk allocation and relationship building in the selection and construction phase. The differences can be explained from both contextual and project related characteristics. Although there are limitations with this research in drawing generalizations across two sets of case projects, the results provide a strong base to explore the nature of incentive systems across different geographical and contextual boundaries in future research.

Unravelling the mechanisms behind the invasion of an introduced and now undesirable grass species

The introduction of Eragrostis curvula (African Lovegrass, herafter Lovegrass) for pasture improvement across Australia has not been successful. Instead Lovegrass, a C4 perennial grass originating from Southern African, has proven unpalatable to stock and to have low nutritional value if stocks do eat it. It has spread prolifically along roadsides, stream banks, conservation areas and pastures. Because control efforts have not been effective, our aim was to determine the putative mechanisms responsible for the dominance of Lovegrass, specifically disturbance (selective grazing) and competition.

Signal transduction mechanisms underlying growth hormone receptor action

Our understanding of the mechanisms of action of GH and its receptor, the GHR, has advanced significantly in the last decade and has provided some important surprises. It is now clear that the GH-GHR axis activates a number of inter-related signalling pathways, not all of which are dependent on the intracellular tyrosine kinase, JAK2 as originally postulated. JAK2-independent pathways, mediated via the Src family kinases, together with a number of negative regulators of GH signalling and emerging cross-talk mechanisms with other growth factor receptors, provide a complex array of mechanisms that are capable of fine-tuning responses to GH in a cell context dependent manner. Additionally, it is also now clear that GH and the GHR can translocate to the nucleus of target cells and initiate, as yet not well defined, nuclear responses. Continued emphasis on elucidation of these complex mechanisms is critical to provide further insights into the diverse physiological and pathophysiological effects of GH.

Combinatorial design of key distribution mechanisms for wireless sensor networks

Secure communications in wireless sensor networks operating under adversarial conditions require providing pairwise (symmetric) keys to sensor nodes. In large scale deployment scenarios, there is no prior knowledge of post deployment network configuration since nodes may be randomly scattered over a hostile territory. Thus, shared keys must be distributed before deployment to provide each node a key-chain. For large sensor networks it is infeasible to store a unique key for all other nodes in the key-chain of a sensor node. Consequently, for secure communication either two nodes have a key in common in their key-chains and they have a wireless link between them, or there is a path, called key-path, among these two nodes where each pair of neighboring nodes on this path have a key in common. Length of the key-path is the key factor for efficiency of the design. This paper presents novel deterministic and hybrid approaches based on Combinatorial Design for deciding how many and which keys to assign to each key-chain before the sensor network deployment. In particular, Balanced Incomplete Block Designs (BIBD) and Generalized Quadrangles (GQ) are mapped to obtain efficient key distribution schemes. Performance and security properties of the proposed schemes are studied both analytically and computationally. Comparison to related work shows that the combinatorial approach produces better connectivity with smaller key-chain sizes.