GREEN MACHINING ORIENTED TO DIMINISH DENSITY GRADIENT FOR MINIMIZATION OF DISTORTION IN ADVANCED CERAMICS

After sintering advanced ceramics, there are invariably distortions, caused in large part by the heterogeneous distribution of density gradients along the compacted piece. To correct distortions, machining is generally used to manufacture pieces within dimensional and geometric tolerances. Hence, narrow material removal limit conditions are applied, which minimize the generation of damage. Another alternative is machining the compacted piece before sintering, called the green ceramic stage, which allows machining without damage to mechanical strength. Since the greatest concentration of density gradients is located in the outer-most layers of the compacted piece, this study investigated the removal of different allowance values by means of green machining. The output variables are distortion after sintering, tool wear, cutting force, and the surface roughness of the green ceramics and the sintered ones. The following results have been noted: less distortion is verified in the sintered piece after 1mm allowance removal; and the higher the tool wear the worse the surface roughness of both green and sintered pieces.

Measurements of the Magnetic Permeabilities of the Iron-Manganese Alloy System Prepared by the Methods of Powder Metallurgy

Powder metallurgy is a branch of metallurgy which produces metallic compacts in their final forms by means of pressure and heat-treatment from the pow­ders. The products of powder metallurgy are being used in our daily lives quite often. For example, the tungsten wires in the electric bulbs to the silver-tin fillings of our teeth.

Microstructure, magnetic and mechanical properties of Ni-Zn ferrites prepared by Powder Injection Moulding

Nowadays, the electronic industry demands small and complex parts as a consequence of the miniaturization of electronic devices. Powder injection moulding (PIM) is an emerging technique for the manufacturing of magnetic ceramics. In this paper, we analyze the sintering process, between 900 °C and 1300 °C, of Ni–Zn ferrites prepared by PIM. In particular, the densification behaviour, microstructure and mechanical properties of samples with toroidal and bar geometry were analyzed at different temperatures. Additionally, the magnetic behaviour (complex permeability and magnetic losses factor) of these compacts was compared with that of samples prepared by conventional powder compaction. Finally, the mechanical behaviour (elastic modulus, flexure strength and fracture toughness) was analyzed as a function of the powder loading of feedstock. The final microstructure of prepared samples was correlated with the macroscopic behaviour. A good agreement was established between the densities and population of defects found in the materials depending on the sintering conditions. In general, the final mechanical and magnetic properties of PIM samples were enhanced relative those obtained by uniaxial compaction.

Negative ternary set-sharing

The Set-Sharing domain has been widely used to infer at compiletime interesting properties of logic programs such as occurs-check reduction, automatic parallelization, and flnite-tree analysis. However, performing abstract uniflcation in this domain requires a closure operation that increases the number of sharing groups exponentially. Much attention has been given to mitigating this key inefflciency in this otherwise very useful domain. In this paper we present a novel approach to Set-Sharing: we define a new representation that leverages the complement (or negative) sharing relationships of the original sharing set, without loss of accuracy. Intuitively, given an abstract state sh\> over the finite set of variables of interest V, its negative representation is p(V) \ shy. Using this encoding during analysis dramatically reduces the number of elements that need to be represented in the abstract states and during abstract uniflcation as the cardinality of the original set grows toward 2 . To further compress the number of elements, we express the set-sharing relationships through a set of ternary strings that compacts the representation by eliminating redundancies among the sharing sets. Our experiments show that our approach can compress the number of relationships, reducing signiflcantly the memory usage and running time of all abstract operations, including abstract uniflcation.

Nuevas arquitecturas de transpondedores de microondas = New transponder architectures at microwave frequencies = Nouvelles architectures des transpondeurs d’hyperfréquences

En la última década, los sistemas de telecomunicación de alta frecuencia han evolucionado tremendamente. Las bandas de frecuencias, los anchos de banda del usuario, las técnicas de modulación y otras características eléctricas están en constante cambio de acuerdo a la evolución de la tecnología y la aparición de nuevas aplicaciones. Las arquitecturas de los transceptores modernos son diferentes de las tradicionales. Muchas de las funciones convencionalmente realizadas por circuitos analógicos han sido asignadas gradualmente a procesadores digitales de señal, de esta manera, las fronteras entre la banda base y las funcionalidades de RF se difuminan. Además, los transceptores inalámbricos digitales modernos son capaces de soportar protocolos de datos de alta velocidad, por lo que emplean una elevada escala de integración para muchos de los subsistemas que componen las diferentes etapas. Uno de los objetivos de este trabajo de investigación es realizar un estudio de las nuevas configuraciones en el desarrollo de demostradores de radiofrecuencia (un receptor y un transmisor) y transpondedores para fines de comunicaciones y militares, respectivamente. Algunos trabajos se han llevado a cabo en el marco del proyecto TECRAIL, donde se ha implementado un demostrador de la capa física LTE para evaluar la viabilidad del estándar LTE en el entorno ferroviario. En el ámbito militar y asociado al proyecto de calibración de radares (CALRADAR), se ha efectuado una actividad importante en el campo de la calibración de radares balísticos Doppler donde se ha analizado cuidadosamente su precisión y se ha desarrollado la unidad generadora de Doppler de un patrón electrónico para la calibración de estos radares. Dicha unidad Doppler es la responsable de la elevada resolución en frecuencia del generador de “blancos” radar construido. Por otro lado, se ha elaborado un análisis completo de las incertidumbres del sistema para optimizar el proceso de calibración. En una segunda fase se han propuesto soluciones en el desarrollo de dispositivos electro-ópticos para aplicaciones de comunicaciones. Estos dispositivos son considerados, debido a sus ventajas, tecnologías de soporte para futuros dispositivos y subsistemas de RF/microondas. Algunas demandas de radio definida por software podrían cubrirse aplicando nuevos conceptos de circuitos sintonizables mediante parámetros programables de un modo dinámico. También se ha realizado una contribución relacionada con el diseño de filtros paso banda con topología “Hairpin”, los cuales son compactos y se pueden integrar fácilmente en circuitos de microondas en una amplia gama de aplicaciones destinadas a las comunicaciones y a los sistemas militares. Como importante aportación final, se ha presentado una propuesta para ecualizar y mejorar las transmisiones de señales discretas de temporización entre los TRMs y otras unidades de procesamiento, en el satélite de última generación SEOSAR/PAZ. Tras un análisis exhaustivo, se ha obtenido la configuración óptima de los buses de transmisión de datos de alta velocidad basadas en una red de transceptores. ABSTRACT In the last decade, high-frequency telecommunications systems have extremely evolved. Frequency bands, user bandwidths, modulation techniques and other electrical characteristics of these systems are constantly changing following to the evolution of technology and the emergence of new applications. The architectures of modern transceivers are different from the traditional ones. Many of the functions conventionally performed by analog circuitry have gradually been assigned to digital signal processors. In this way, boundaries between baseband and RF functionalities are diffused. The design of modern digital wireless transceivers are capable of supporting high-speed data protocols. Therefore, a high integration scale is required for many of the components in the block chain. One of the goals of this research work is to investigate new configurations in the development of RF demonstrators (a receiver and a transmitter) and transponders for communications and military purposes, respectively. A LTE physical layer demonstrator has been implemented to assess the viability of LTE in railway scenario under the framework of the TECRAIL project. An important activity, related to the CALRADAR project, for the calibration of Doppler radars with extremely high precision has been performed. The contribution is the Doppler unit of the radar target generator developed that reveals a high frequency resolution. In order to assure the accuracy of radar calibration process, a complete analysis of the uncertainty in the above mentioned procedure has been carried out. Another important research topic has been the development of photonic devices that are considered enabling technologies for future RF and microwave devices and subsystems. Some Software Defined Radio demands are addressed by the proposed novel circuit concepts based on photonically tunable elements with dynamically programmable parameters. A small contribution has been made in the field of Hairpin-line bandpass filters. These filters are compact and can also be easily integrated into microwave circuits finding a wide range of applications in communication and military systems. In this research field, the contributions made have been the improvements in the design and the simulations of wideband filters. Finally, an important proposal to balance and enhance transmissions of discrete timing signals between TRMs and other processing units into the state of the art SEOSAR/PAZ Satellite has been carried out obtaining the optimal configuration of the high-speed data transmission buses based on a transceiver network. RÉSUMÉ Les systèmes d'hyperfréquence dédiés aux télécommunications ont beaucoup évolué dans la dernière décennie. Les bandes de fréquences, les bandes passantes par utilisateur, les techniques de modulation et d'autres caractéristiques électriques sont en constant changement en fonction de l'évolution des technologies et l'émergence de nouvelles applications. Les architectures modernes des transcepteurs sont différentes des traditionnelles. Un grand nombre d’opérations normalement effectuées par les circuits analogiques a été progressivement alloué à des processeurs de signaux numériques. Ainsi, les frontières entre la bande de base et la fonctionnalité RF sont floues. Les transcepteurs sans fils numériques modernes sont capables de transférer des données à haute vitesse selon les différents protocoles de communication utilisés. C'est pour cette raison qu’un niveau élevé d'intégration est nécessaire pour un grand nombre de composants qui constitue les différentes étapes des systèmes. L'un des objectifs de cette recherche est d'étudier les nouvelles configurations dans le développement des démonstrateurs RF (récepteur et émetteur) et des transpondeurs à des fins militaire et de communication. Certains travaux ont été réalisés dans le cadre du projet TECRAIL, où un démonstrateur de la couche physique LTE a été mis en place pour évaluer la faisabilité de la norme LTE dans l'environnement ferroviaire. Une contribution importante, liée au projet CALRADAR, est proposée dans le domaine des systèmes d’étalonnage de radar Doppler de haute précision. Cette contribution est le module Doppler de génération d’hyperfréquence intégré dans le système électronique de génération de cibles radar virtuelles que présente une résolution de fréquence très élevée. Une analyse complète de l'incertitude dans l'étalonnage des radars Doppler a été effectuée, afin d'assurer la précision du calibrage. La conception et la mise en oeuvre de quelques dispositifs photoniques sont un autre sujet important du travail de recherche présenté dans cette thèse. De tels dispositifs sont considérés comme étant des technologies habilitantes clés pour les futurs dispositifs et sous-systèmes RF et micro-ondes grâce à leurs avantages. Certaines demandes de radio définies par logiciel pourraient être supportées par nouveaux concepts de circuits basés sur des éléments dynamiquement programmables en utilisant des paramètres ajustables. Une petite contribution a été apportée pour améliorer la conception et les simulations des filtres passe-bande Hairpin à large bande. Ces filtres sont compacts et peuvent également être intégrés dans des circuits à micro-ondes compatibles avec un large éventail d'applications dans les systèmes militaires et de communication. Finalement, une proposition a été effectuée visant à équilibrer et améliorer la transmission des signaux discrets de synchronisation entre les TRMs et d'autres unités de traitement dans le satellite SEOSAR/PAZ de dernière génération et permettant l’obtention de la configuration optimale des bus de transmission de données à grande vitesse basés sur un réseau de transcepteurs.

Design of a new neutron delivery system for high flux source

La construcción en la actualidad de nuevas fuentes para el uso de haces de neutrones así como los programas de renovación en curso en algunas de las instalaciones experimentales existentes han evidenciado la necesidad urgente de desarrollar la tecnología empleada para la construcción de guías de neutrones con objeto de hacerlas mas eficientes y duraderas. Esto viene motivado por el hecho de que varias instalaciones de experimentación con haces de neutrones han reportado un número de incidentes mecánicos con tales guías, lo que hace urgente el progresar en nuestro conocimiento de los susbtratos vítreos sobre los cuales se depositan los espejos que permiten la reflexión total de los neutrones y como aquellos se degradan con la radiación. La presente tesis se inscribe en un acuerdo de colaboración establecido entre el Institut Max von Laue - Paul Langevin (ILL) de Grenoble y el Consorcio ESS-Bilbao con objeto de mejorar el rendimiento y sostenibilidad de los sistemas futuros de guiado de neutrones. El caso de la Fuente Europea de Espalación en construcción en Lund sirve como ejemplo ya que se contempla la instalación de guías de neutrones de más de 100 metros en algunos de los instrumentos. Por otro lado, instalaciones como el ILL prevén también dentro del programa Endurance de rejuvenecimiento la reconstrucción de varias líneas de transporte de haz. Para el presente estudio se seleccionaron cuatro tipos de vidrios borosilicatados que fueron el Borofloat, N-ZK7, N-BK7 y SBSL7. Los tres primeros son bien conocidos por los especialistas en instrumentación neutrónica ya que se han empleado en la construcción de varias instalaciones mientras que el último es un candidato potencial en la fabricación de substratos para espejos neutrónicos en un futuro. Los cuatro vidrios tiene un contenido en óxido de Boro muy similar, approximadamente un 10 mol.%. Tal hecho que obedece a las regulaciones para la fabricación de estos dispositivos hace que tales substratos operen como protección radiológica absorbiendo los neutrones transmitidos a través del espejo de neutrones. Como contrapartida a tal beneficio, la reacción de captura 10B(n,_)7Li puede degradar el substrato vítreo debido a los 2.5 MeV de energía cinética depositados por la partícula _ y los núcleos en retroceso y de hecho la fragilidad de tales vidrios bajo radiación ha sido atribuida desde hace ya tiempo a los efectos de esta reacción. La metodología empleada en esta tesis se ha centrado en el estudio de la estructura de estos vidrios borosilicatados y como esta se comporta bajo condiciones de radiación. Los materiales en cuestión presentan estructuras que dependen de su composición química y en particular del ratio entre formadores y modificadores de la red iono-covalente. Para ello se han empleado un conjunto de técnicas de caracterización tanto macro- como microscópicas tales como estudios de dureza, TEM, Raman, SANS etc. que se han empleado también para determinar el comportamiento de estos materiales bajo radiación. En particular, algunas propiedades macroscópicas relacionadas con la resistencia de estos vidrios como elementos estructurales de las guías de neutrones han sido estudiadas así como también los cambios en la estructura vítrea consecuencia de la radiación. Para este propósito se ha diseñado y fabricado por el ILL un aparato para irradiación de muestras con neutrones térmicos en el reactor del ILL que permite controlar la temperatura alcanzada por la muestra a menos de 100 °C. Tal equipo en comparación con otros ya existences permite en cuestión de dias acumular las dosis recibidas por una guía en operación a lo largo de varios años. El uso conjunto de varias técnicas de caracterización ha llevado a revelar que los vidrios aqui estudiados son significativamente diferentes en cuanto a su estructura y que tales diferencias afectan a sus propiedades macroscópicas asi como a su comportamiento bajo radiación. Tal resultado ha sido sorprendente ya que, como se ha mencionado antes, algunos de estos vidrios eran bien conocidos por los fabricantes de guías de neutrones y hasta el momento eran considerados prácticamente similares debido a su contenido comparable en óxido de Boro. Sin embargo, los materiales N-BK7 and S-BSL7 muetran gran homogeneidad a todas las escalas de longitud, y más específicamente, a escalas nanométricas las subredes de Sílice y óxido de Boro se mezclan dando logar a estructuras locales que recuerdan a la del cristal de Reedmergnerita. Por el contrario, N-ZK7 y Borofloat muestran dominios separados ricos en Sílice o Boro. Como era de esperar, las importantes diferencias arriba mencionadas se traducen en comportamientos dispares de estos materiales bajo un haz de neutrones térmicos. Los resultados muestran que el N-BK7 y el S-BSL7 son los más estables bajo radiación, lo que macroscópicamente hace que estos materiales muestren un comportamiento similar expandiéndose lentamente en función de la dosis recibida. Por el contario, los otros dos materiales muestran un comportamiento mucho más reactivo, que hace que inicialmente se compacten con la dosis recibida lo que hace que las redes de Silicio y Boro se mezclen resultando en un incremento en densidad hasta alcanzar un valor límite, seguido por un proceso de expansión lenta que resulta comparable al observado para N-BK7 y SBSL7. Estos resultados nos han permitido explicar el origen de las notorias diferencias observadas en cuanto a las dosis límite a partir de las cuales estos materiales desarrollan procesos de fragmentación en superficie. ABSTRACT The building of new experimental neutron beam facilities as well as the renewal programmes under development at some of the already existing installations have pinpointed the urgent need to develop the neutron guide technology in order to make such neutron transport devices more efficient and durable. In fact, a number of mechanical failures of neutron guides have been reported by several research centres. It is therefore important to understand the behaviour of the glass substrates on top of which the neutron optics mirrors are deposited and how these materials degrade under radiation conditions. The case of the European Spallation Source (ESS) at present under construction at Lund is a good example. It previews the deployment of neutron guides having more than 100 metres of length for most of the instruments. Also, the future renovation programme of the ILL, called Endurance, foresees the refurbishment of several beam lines. This Ph.D. thesis was the result of a collaboration agreement between the ILL and ESS-Bilbao aiming to improve the performance and sustainability of future neutron delivery systems. Four different industrially produced alkali-borosilicate glasses were selected for this study: Borofloat, N-ZK7, N-BK7 and SBSL7. The first three are well known within the neutron instrumentation community as they have already been used in several installations whereas the last one is at present considered as a candidate for making future mirror substrates. All four glasses have a comparable content of boron oxide of about 10 mol.%. The presence of such a strong neutron absorption element is in fact a mandatory component for the manufacturing of neutron guides because it provides a radiological shielding for the environment. This benefit is however somewhat counterbalanced since the resulting 10B(n,_)7Li reactions degrade the glass due to the deposited energy of 2.5 MeV by the _ particle and the recoil nuclei. In fact, the brittleness of some of these materials has been ascribed to this reaction. The methodology employed by this study consisted in understanding the general structure of borosilicates and how they behave under irradiation. Such materials have a microscopic structure strongly dependent upon their chemical content and particularly on the ratios between network formers and modifiers. The materials have been characterized by a suite of macroscopic and structural techniques such as hardness, TEM, Raman, SANS, etc. and their behaviour under irradiation was analysed. Some macroscopic properties related to their resistance when used as guide structural elements were monitored. Also, changes in the vitreous structure due to radiation were observed by means of several experimental tools. For such a purpose, an irradiation apparatus has been designed and manufactured to enable irradiation with thermal neutrons within the ILL reactor while keeping the samples below 100 °C. The main advantage of this equipment if compared to others previously available was that it allowed to reach in just some days an equivalent neutron dose to that accumulated by guides after several years of use. The concurrent use of complementary characterization techniques lead to the discovery that the studied glasses were deeply different in terms of their glass network. This had a strong impact on their macroscopic properties and their behaviour under irradiation. This result was a surprise since, as stated above, some of these materials were well known by the neutron guide manufacturers, and were considered to be almost equivalent because of their similar boron oxide content. The N-BK7 and S-BSL7 materials appear to be fairly homogeneous glasses at different length scales. More specifically, at nanometre scales, silicon and boron oxide units seem to mix and generate larger structures somewhat resembling crystalline Reedmergnerite. In contrast, N-ZK7 and Borofloat are characterized by either silicon or boron rich domains. As one could expect, these drastic differences lead to their behaviour under thermal neutron flux. The results show that N-BK7 and S-BSL7 are structurally the most stable under radiation. Macroscopically, such stability results in the fact that these two materials show very slow swelling as a function or radiation dose. In contrast, the two other glasses are much more reactive. The whole glass structure compacts upon radiation. Specifically, the silica network, and the boron units tend to blend leading to an increase in density up to some saturation, followed by a very slow expansion which comes to be of the same order than that shown by N-BK7 and S-BSL7. Such findings allowed us to explain the drastic differences in the radiation limits for macroscopic surface splintering for these materials when they are used in neutron guides.

Trajectory of DNA in the RNA polymerase II transcription preinitiation complex

By using site-specific protein-DNA photocrosslinking, we define the positions of TATA-binding protein, transcription factor IIB, transcription factor IIF, and subunits of RNA polymerase II (RNAPII) relative to promoter DNA within the human transcription preinitiation complex. The results indicate that the interface between the largest and second-largest subunits of RNAPII forms an extended, ≈240 Å channel that interacts with promoter DNA both upstream and downstream of the transcription start. By using electron microscopy, we show that RNAPII compacts promoter DNA by the equivalent of ≈50 bp. Together with the published structure of RNAPII, the results indicate that RNAPII wraps DNA around its surface and suggest a specific model for the trajectory of the wrapped DNA.

Topologias maximais com respeito a algumas famílias de subconjuntos

Seja (X; t) um espaço topológico e seja F a família de todos os subconjuntos de X que satisfazem uma propriedade topológica dada P (invariante por homeomorfismos). Se acrescentarmos abertos novos à topologia e se F\' é a família de todos os subconjuntos do novo espaço que satisfazem a propriedade P, podemos ter que F ≠ F\'. Se isto sempre acontece, dizemos que o espaço (X; t) é maximal com respeito à família F. Neste trabalho estudaremos os espaços topológicos maximais com respeito a algumas famílias de subconjuntos: discretos, compactos, densos, conexos e das sequências convergentes.

Sinterização flash do condutor catiônico beta-alumina sintetizada pelo método dos precursores poliméricos.

A beta-alumina de sódio é uma cerâmica condutora de íons Na+ utilizada como eletrólito sólido em baterias de sódio para armazenamento de energias intermitentes como energia solar e eólica. Devido ao alto teor de sódio, esse material é instável a altas temperaturas, podendo sofrer variações de composição durante a etapa de sinterização convencional que utiliza altas temperaturas por longos períodos de tempo. A sinterização flash é uma técnica de sinterização ativada por corrente elétrica que proporciona a densificação de compactos cerâmicos em poucos segundos, a temperaturas notavelmente mais baixas que as convencionais. Uma vez obrigatória a passagem de corrente elétrica através da amostra, a sinterização flash de qualquer material condutor parece bastante razoável. Não obstante, até o presente momento a maioria dos trabalhos publicados sobre o assunto aborda apenas condutores de vacância de oxigênio ou semicondutores, materiais compatíveis com eletrodos de platina (Pt). Nesse trabalho a sinterização flash de um condutor catiônico foi estudada utilizando-se a beta-alumina como material modelo. A beta-alumina foi sintetizada pelo método dos precursores poliméricos, caracterizada e então submetida à sinterização flash. O material de eletrodo padrão (platina) provou ser um eletrodo bloqueador em contato com a beta-alumina. O sucesso da sinterização flash foi determinado pela troca do material de eletrodo por prata (Ag), o que possibilitou uma reação eletroquímica reversível nas interfaces eletrodo-cerâmica e possibilitou a obtenção de um material densificado com morfologia e composição química homogêneas. Devido à metaestabilidade da beta-alumina, a atmosfera dos experimentos precisou ser alterada para manter a integridade desse material rico em um metal alcalino (Na+). A sinterização flash de um condutor catiônico é apresentada pela primeira vez na literatura e ressalta a importância da reação de eletrodo, que é um fator limitante para o sucesso da sinterização flash e precisa ser estudada e adaptada para cada tipo de material.

Denver Water, Policy and Economics

An analysis of the Denver Water Department finds that it is charged with supplying water to over 1.1 million residents in the Denver Metropolitan area. With assets of over $1.2 billion dollars and a governing board of five appointed members who must make policy and financial decisions under unusual circumstances for most water districts. Those circumstances include; Colorado is the only State that has a single source of water, precipitation, State and Federal mandated water compacts that limits water resources further, and Colorado Constitutional mandated appropriation water laws. Combined together these circumstances create a difficult atmosphere for policy making and financial planning. When comparing the Denver Water Board with other water departments around the Country, the Denver Water Department seems to be competent in all areas.

Production of nanoTiC–graphite composites using Ti-doped self-sintering carbon mesophase powder

This work reports the synthesis of nanoTiC–graphite composites using mesophase pitch containing titanium as TiC or TiO2 nanoparticles. NanoTiC–graphite composites have been prepared using Ti-doped self-sintering mesophase powders as starting materials without using any binders or a metal carbide-carbon mixing stage. The effect of manufacture variables on the graphite compacts properties was studied. Graphites were characterised using XRD and Raman spectroscopy, SEM and TEM, as well as by their mechanical, electrical and thermal properties. The presence of TiC promotes graphitisation producing materials with larger crystal sizes. The kind of titanium source and mesophase content of the starting pitch affects to the final properties. Mesophase pitch with higher amount of mesophase content produces graphites with higher degree of graphitisation. The incorporation of TiC nanoparticles to the graphites composites improved thermal conductivity more than four times, and mechanical properties are not significantly modified by the presence of TiC.

The fiscal compact - Europe's "hard core" based on German economic conditions. OSW Commentary No. 71, 2012-03-07

On 2 March, the leaders of 25 EU member states signed the Treaty on stability, coordination and governance in the economic and monetary union. It will introduce new fiscal constraints and officially vest new competences in the eurozone countries. Thus, their right to coordinate economic policy among them will be sanctioned. So far, the Lisbon Treaty has only provided for organisation of informal Eurogroup meetings, to be attended by representatives of the European Commission. The principles introduced by the compact, if the eurozone countries are really determined to observe its provisions, will create a new way of managing the single currency. Within the next few years, the most indebted countries will have to carry out radical reforms to boost their competitiveness and adjust it to German standards. During this period the Federal Republic of Germany will most probably decide to offer higher loan guarantees to relieve these countries’ budgets. The compact’s political consequences are also of great significance, especially considering how the treaty was finalised. The eurozone states have in fact accepted that the direction for changes will be devised by France and Germany, and the role of European institutions such as the Commission or the Parliament may weaken. From the perspective of eurozone candidate countries, the introduction of the fiscal compact means expanding the scope of conditions they must meet to become members of the single currency area. In the future, a country, in order to adopt the single currency, will have to meet the structural deficit criterion, and also most probably carry out economic reforms such as unifying its fiscal system. These goals will be achieved across the eurozone gradually, in the subsequent stages of the economic governance reform.

Maastricht 2.0 - Proposed reform of EU sovereign debt rules. Policy Brief #2012/05

The European Union’s regulations governing sovereign debt are based on the principle of equal treatment of all member states. The recommendations we make here concerning changes in European Union sovereign-debt reduction rules take account of national particularities, but are by no means arbitrary in nature. According to the calculations we present here, such reformed regulations would do far more to promote economic growth than would be the case under the Fiscal Compact’s European debt brake. By 2030, real gains in growth will amount to more than 450 billion euros more than the outcome that would presumably be obtained under the European debt brake.

Beryllium--fabrication and joining : a literature search /

This search, containing 128 references, was prepared to serve as a guide to the report literature on the fabrication and joining of beryllium. Studies on compacts and powder metallurgy are included. Articles selected from scientific journals and which appear in Nuclear Science Abstracts (NSA) are included. Reports are listed alpha-numerically under the issuing agency.

Glucose affects monocarboxylate cotransporter (MCT) 1 expression during mouse preimplantation development

Cleavage-stage embryos have an absolute requirement for pyruvate and lactate, but as the morula compacts, it switches to glucose as the preferred energy source to fuel glycolysis. Substrates such as glucose, amino acids, and lactate are moved into and out of cells by facilitated diffusion. in the case of lactate and pyruvate, this occurs via H+-monocarboxylate cotransporter (MCT) proteins. To clarify the role of MCT in development, transport characteristics for DL-lactate were examined, as were mRNA expression and protein localisation for MCT1 and MCT3, using confocal laser scanning immunofluorescence in freshly collected and cultured embryos. Blastocysts demonstrated significantly higher affinity for DL-lactate than zygotes (K-m 20 +/- 10 vs 87 +/- 35 mmol lactate/l; P = 0.03 by linear regression) but was similar for all stages. For embryos derived in vivo and those cultured with glucose, MCT1 mRNA was present throughout preimplantation development, protein immunoreactivity appearing diffuse throughout the cytoplasm with brightest intensity in the outer cortical region of blastomeres. in expanding blastocysts, MCT1 became more prominent in the cytoplasmic cortex of blastomeres, with brightest intensity in the polar trophectoderm. Without glucose, MCT1 mRNA was not expressed, and immunoreactivity dramatically reduced in intensity as morulae died. MCT3 mRNA and immunoreactivity were not detected in early embryos. The differential expression of MCT1 in the presence or absence of glucose demonstrates that it is important in the critical regulation of pH and monocarboxylate transport during preimplantation development, and implies a role for glucose in the control of MCT1, but not MCT3, expression.