Sola romani: morteros hidráulicos romanos en la Península Ibérica

En esta investigación se han analizado morteros de cal de cronología romana en el interior de la Península Ibérica. Para ello, se seleccionó una serie de muestras procedentes de diversos yacimientos, y de estructuras de carácter industrial. Estas muestras presentan aditivos cerámicos y conglomerantes de cal, como característica principal. Desde un principio el esfuerzo debía de centrarse en los fragmentos cerámicos presentes en los morteros. Para ello se documentaron varios morteros con aditivos cerámicos, a fin de conocer sus características básicas (componentes, distribución, micro-estratigrafía, granulometría, etc.). Por ello, y una vez tomadas las muestras, ésta fueron tratadas y procesadas para desarrollar una primera fase de estudio por medio de macroscopía. Se obtuvieron buenos resultados en cuanto a la caracterización visual de los morteros, localizando y documentando los fragmentos cerámicos. Durante la observación de dichos aditivos se observó que los fragmentos cerámicos tenían unas coronas o anillos de coloración que recorrían el borde, justo al contacto con la matriz de cal. Fueron seleccionados algunos fragmentos en los que eran más visibles dichos anillos. A fin de conocer la posible relación entre algunos yacimientos cercanos y la presencia de dicho anillo cromáticos se desarrolló una microscopía óptica polarizada, realizando láminas delgadas de las muestras y sobre los fragmentos cerámicos más determinantes, en concreto de una serie de enclaves del valle del Henares. Además de caracterizar microscópicamente los morteros, se observó que los anillos no eran un defecto visual ni una alteración física, producida tal vez por la extracción, la fase del corte o por la cocción de la cerámica. Tras analizar varios ejemplares se pudo apreciar que esos anillos eran habituales en todas las muestras y que se presentaban de diferente manera, es decir, que se observaban en granos cerámicos de diferentes características físicas (cochura, tamaño, situación con respecto del conglomerante, etc.). A fin de conocer los aspectos químicos de dicha alteración se seleccionó un grupo de muestras en las que los resultados macroscópicos habían sido muy claros, y en las que la microscopía óptica polarizada había determinado en los bordes, áreas adecuadas para otros análisis. Se realizó un mapeado o mapping de elementos químicos, a fin de saber qué podía estar sucediendo en esa interfaz entre el fragmento cerámico y la matriz de cal. Gracias a los resultados obtenidos se comprobó que existía una acumulación potencial de calcio tanto en el interior de los granos cerámicos como en el exterior, justo en la zona de contacto con el conglomerante, formando manchas que recorrían longitudinalmente el borde. Estos datos fueron muy útiles para llevar a cabo la siguiente fase de estudio, que permitiría conocer puntualmente qué estaba sucediendo químicamente en esa zona de contacto. Finalmente y con el objetivo de describir química y puntualmente este efecto en las adiciones cerámicas, se volvió a seleccionar una serie de muestras, escogidas esta vez en función de los granos cerámicos que cumpliesen unas variables estadísticas. Se eligieron granos con distintos tipos de cocciones, así como granos con tamaños diversos y granos con aditivo ceniciento en la matriz de cal, pensando que podrían ser las variables más útiles de interpretar de existir algún tipo de cambio químico entre la arcilla cocida y la matriz de cal. Tales variables se adaptaron a un sistema estadístico multi-varial y geométrico, con el objetivo de sintetizar los resultados y visualizar de forma óptima los datos en conjunto, como se ha comentado en varias ocasiones en este trabajo. Una vez seleccionados los granos por variables se procedió a realizar un análisis lineal y espectral semi-cuantitativo de SEM-EDX, con el que se caracterizaba químicamente una sección lineal del grano, desde la matriz de arcilla cocida de la cerámica hasta la matriz de cal –del interior al exterior del grano- pasando por el centro de la banda de reacción. Este análisis permitió determinar que se había producido una serie de cambios químicos porcentuales en los granos de cerámica. Dichos cambios se resumen en un incremento global de los porcentajes de calcio en el interior de las bandas de reacción de la cerámica, desde el borde mismo del anillo hasta el exterior. Así también se observaron picos porcentuales en el interfaz del fragmento cerámico con la matriz de cal, lo que confirmaba los resultados obtenidos por medio del mapping. Globalmente en todas las muestras se apreció un hombro en las gráficas de calcio a su paso por la zona de afección del anillo de reacción. Los restantes porcentajes de magnesio, silicio y aluminio se mantienen normales. En esta tesis se ha confirmado que dicho incremento global de calcio se acentúa en las muestras en donde no hay cenizas en la matriz de cal. Los casos correspondientes a estos granos sufren un incremento mayor que en el resto. La segunda variable que sufre un mayor incremento de calcio es la que corresponde a granos con buena cocción de la arcilla. Por lo tanto, parece que la tercera variable, la que corresponde con el tamaño del fragmento cerámico, no es decisiva. Por lo tanto, teniendo en cuenta la prueba visual de los anillos de reacción, y atendiendo a los resultados químicos, podríamos pensar que ese incremento de calcio en la banda de reacción de los fragmentos cerámicos se debió a una absorción de calcio en el interior de la arcilla cocida en la fase inmediatamente previa al fraguado, incluso durante el apagado de la cal. Es en este punto donde estaría la clave del cambio químico que se produce en esta interfaz, el calcio sílice-aluminato del que algunos autores ya han investigado. Esta absorción de calcio en el interior del grano no vendría sola, sino que generaría una costra de cal en el interfaz exterior de la cerámica, la cual ha sido observada químicamente por mapping y mineralógicamente por medio de microscopía óptica de polarización. La consecuencia de estos resultados es, primero, la mejora de nuestro conocimiento general acerca del factor hidráulico en los morteros. Asimismo se aprecia que la incorporación de materiales orgánicos como cenizas, puede alterar los porcentajes de calcio en el interior de los aditivos cerámicos, por lo que habría que sopesar, en trabajos futuros, si este tipo de material es adecuado o no en las mezclas destinadas a la restauración, así como seguir indagando en las propiedades de los morteros con la incorporación de aditivos orgánicos. Desde el punto de vista de la catalogación de los suelos industriales hidráulicos de época romana, además de mejorar la documentación incorporando micro-estratigrafías y granulometrías, la investigación de este material histórico constructivo mejora en cuanto a que se incorporan ensayos sencillos, que facilitan incluso la peritación de un estado de conservación por medio de una lupa binocular. Arqueológicamente hablando, es muy interesante correlacionar fábricas diferentes de estructuras situadas o bien en un mismo yacimiento, o bien en una misma área regional. Los estudios de caracterización y micro-estratigrafía no sólo aportan datos nuevos de cara a la restauración de morteros, sino que crean la posibilidad de generar patrones constructivos que sirvan de fósiles-guía para datar relativamente a unas estructuras o a otras. En lo referido a los resultados obtenidos en los diferentes complejos arqueológicos se ha observado una diferencia entre los morteros destinados a piletas y cubetas con respecto a los suelos industriales de uso indeterminado. La muestra correspondiente al yacimiento de Las Arenas no dispone de ninguna micro-estratigrafía, como sí por el contrario en las muestras obtenidas en Rotonda de Mejorada, Val de la Viña y La Magdalena. En estos enclaves las estructuras presentan grandes similitudes, con diferentes niveles constructivos empleando morteros de cal con áridos y gravas en las capas interiores, y áridos con adiciones cerámicas en las exteriores. En lo relativo a la granulometría las adiciones cerámicas de las muestras de Val de la Viña y La Magdalena presentan varias coincidencias en cuanto al tamaño de los granos y la distribución. Asimismo, de las muestras tomadas en La Magdalena, existe una gran diferencia entre las muestras MG1, MG2, MG3 y MG4 con respecto a las muestras MG5 y MG6, correspondientes éstas últimas a un mortero con fragmentos cerámicos de gran tamaño. Las estructuras EMG1 y EMG2, correspondientes a una cubeta y una pileta de La Magdalena, guardan similitud en lo referido a la micro-estratigrafía y a la granulometría. Se ha determinado que su función, así como su fabricación, debieron estar vinculadas a un mismo contexto cronocultural. Química y mineralógicamente, las muestras presentan características iguales, con presencia de un conglomerante de cal con áridos y aditivos cerámicos de diferentes cochuras. Destaca la muestra de Las Arenas, con un tamaño de los fragmentos cerámicos muy superior al resto, seguido de la estructura EMG3 de La Magdalena. Las muestras restantes de éste enclave, junto con las muestras recogidas en Val de la Viña y Rotonda de Mejorada presentan condiciones similares. En conclusión, los datos revelan que existían diferentes fábricas destinadas a distintas finalidades, y que las estructuras industriales empleaban aditivos cerámicos para la manipulación de productos con líquidos, de distintas densidades pero que requerían de cierto grado de hidraulicidad. ABSTRACT Lime Roman mortars from the Iberian Peninsula has been analyzed in this reesearch. A group of samples were selected from some sites and all the samples come from industrial structures. All this samples show ceramic additives. From the start, the effort was centered in the pieces of pottery that were found in the mortars. The samples were treated and processed to develop a first phase of the research using macroscopy. With this technique, great results were achieved in the characterization of mortars, the microstratigraphy and the location of the ceramic pieces. While observing these pieces, it was seen that the fragments of pottery had a ring bordering the piece. The pieces with the bigger and more vivid rings were chosen and they were analyzed by a polarized light microscope. The mortars were characterized microscopically and it also showed that the rings were not a physical alteration or a visual defect. After some more tests, the rings were a chemical change associated with the hydraulicity of the mortar. The best samples were selected and mappings of their chemical elements were performed in order to know what could be happening in the interface between the ceramic matrix fragment and lime. With the results obtained it was found that there was a potential; both calcium accumulation within the ceramic grains and outside, just in the area of contact with the binder, forming spots longitudinally along the edge. These data were very useful for carrying out the next phase of study, which would meet promptly what was happening chemically in the area of contact. Another group of samples were taken, and this time focused on ceramic grains that met a statistical variables. Grains were chosen with two types of cooking as well as grains with different sizes and grains with ash additive in the matrix of lime, thinking that might be the most logical to be some sort of chemical change between the baked clay and lime array variables . Such variables were adapted to a multi-varial and geometric statistical system in order to synthesize the results and optimally display the data together, as mentioned several times in this work. After selecting the variables grains proceeded to perform a linear and spectral analysis SEM-EDX. This analysis led to determine that the chemical changes were graduals. These changes are summarized in an increase in the percentages of calcium inside the reaction rim of ceramics, from the edge to the outer ring. So percentage increasing is also observed at the interface of the ceramic matrix fragment with lime, confirming the results obtained by the mapping. Overall in all samples can be seen a shoulder in graphic calcium through the area of the ring reaction condition. The remaining percentages of magnesium, silicon and aluminum are usual. We have promptly confirmed that the increase of calcium is accentuated in samples where there is no ash and lime matrix. Cases for these grains suffer a greater increase than the rest. The second variable suffering more calcium is increased corresponding to good cooking grains with clay. Therefore, it appears that the variable size of the fragment is not critical. Therefore, considering the visual tests to the rings and their response to chemical results, we might think that increasing calcium inside the ceramic fragments was due to an injection of calcium inside clay in the run-up to the setting phase. It is at this point that would be the key to the chemical change that occurs at this interface, silica-calcium aluminate some authors have already investigated. This injection of calcium into the grain does not come alone, but generate a lime crust on the outside interface of ceramics, which we tested for mapping is real in our samples. The consequence of these results is the improvement of our understanding of historical hydraulic factor in building materials, such as mortar. For example, knowing that the incorporation of organic materials such as ash powder, may be detrimental to the injection of calcium inside the ceramic additives. Archaeologically speaking, it's very interesting to correlate different factories or structures located on a single site, or in the same regional area. Characterization studies and microstratigraphy not only provide new information to help restore mortars, but create the possibility of generating constructive patterns that serve as guide fossils to determinate the age of the structures. With regard to the results obtained in different archaeological sites it has seen a difference between mortars of pools or sinks with respect to industrial floors of undetermined use. The sample of the site of Las Arenas does not have any micro-stratigraphy, as if instead in the samples obtained in Rotonda de Mejorada, Val de la Viña and La Magdalena sites. In these settlements the structures are really similar, with different construction levels using lime mortars with aggregates and gravel in the inner layers, and ceramic aggregates as external additions. With regard to the grain size of the ceramic additions Val de la Viña and La Magdalena samples has several coincidences about the size of grains and distribution. Also, samples taken at La Magdalena, there is a difference between the MG1, MG2, MG3 and MG4 samples and the MG5 and MG6 samples, so the last corresponding to a mortar samples with larger ceramic fragments. The EMG1 and EMG2 structures, corresponding to a bucket and a pool of La Magdalena settlement, have similarities with regard to micro-stratigraphy and grain size. It has been determined that the function and manufacturing must be linked with a same chronocultural context.

The durability of glass fibre reinforced cements made with new cementitious matrices

Widespread use of glass fibre reinforced cement (GRC) has been impeded by concerns over its durability. Three degradation mechanisms are proposed - fibre corrosion, Ca(OHh precipitation and matrix densification - although their relative importance is debated. Matrices with reduced alkalinities and Ca(OH)2 contents are being developed; the aim of this study was to investigate their hydration and interaction with alkali-resistant fibres to determine the factors controlling their long-term durability, and assess the relevancy of accelerated ageing. The matrices studied were: OPC/calcium-sulphoaluminate cement plus metakaolin (C); OPC plus metakaolin (M); blast-furnace slag cement plus a micro-silica based additive (D); and OPC (O). Accelerated ageing included hot water and cyclic regimes prior to tensile testing. Investigations included pore solution expression, XRD, DTA/TG, SEM and optical petrography. Bond strength was determined from crack spacings using microstructural parameters obtained from a unique image analysis technique. It was found that, for the new matrices - pore solution alkalinities were lower; Ca(OH)2 was absent or quickly consumed; different hydrates were formed at higher immersion temperatures; degradation under 65°C immersion was an order of magnitude slower, and no interfilamental Ca(OH)2 was observed .It was concluded that: fibre weakening caused by flaw growth was the primary degradation mechanism and was successfully modelled on stress corrosion/static fatigue principles. OPC inferiority was attributed partly to its higher alkalinity but chiefly to the growth of Ca(OH)2 aggravating the degradation; and hot water ageing although useful in model formulation and contrasting the matrices, changed the intrinsic nature of the composites rather than simply accelerating the degradation mechanisms.

The Influence of Calcium Chloride on the Setting Time, Solubility, Disintegration, and pH of Mineral Trioxide Aggregate and White Portland Cement with a Radiopacifier

This study evaluated the influence of addition of 10% calcium chloride (CaCl(2)) on the setting time, solubility, disintegration, and pH of white MTA (WMTA) and white Portland cement (WPC). A test of the setting time was performed following the #57 ADA specifications and a test of the final setting time according to the ASTM. For the solubility tests disintegration and pH, Teflon rings were filled with the cements and weighed after setting. After 24 h in a desiccator, they were once again weighed. Thereafter, they were immersed in MiliQ water for 24 and 72 h and 7, 14, and 28 days, with maintenance in the desiccator and weighing between periods. The pH of water in which the rings were immersed was measured immediately after contact with them and in the other periods. The addition of CaCl(2) provided a significant reduction (50%) in the initial setting time of cements. The final setting time of WMTA was reduced in 35.5% and the final setting time of WPC in 68.5%. The WMTA with CaCl(2) absorbed water and gained weight with time, except for in the 24-h period. The addition of CaCl(2) to the WPC reduced its solubility. The addition of CaCl(2) increased the pH of WMTA in the immediate period and at 24 and 72 h and for WPC in the immediate period and at 24 h. The addition of CaCl(2) to WMTA and WPC reduced the setting times and solubility of both and increased the pH of cements in the initial periods. (J Endod 2009;35:550-554)

The Influence of Calcium Chloride on the Setting Time, Solubility, Disintegration, and pH of Mineral Trioxide Aggregate and White Portland Cement with a Radiopacifier

This study evaluated the influence of addition of 10% calcium chloride (CaCl(2)) on the setting time, solubility, disintegration, and pH of white MTA (WMTA) and white Portland cement (WPC). A test of the setting time was performed following the #57 ADA specifications and a test of the final setting time according to the ASTM. For the solubility tests disintegration and pH, Teflon rings were filled with the cements and weighed after setting. After 24 h in a desiccator, they were once again weighed. Thereafter, they were immersed in MiliQ water for 24 and 72 h and 7, 14, and 28 days, with maintenance in the desiccator and weighing between periods. The pH of water in which the rings were immersed was measured immediately after contact with them and in the other periods. The addition of CaCl(2) provided a significant reduction (50%) in the initial setting time of cements. The final setting time of WMTA was reduced in 35.5% and the final setting time of WPC in 68.5%. The WMTA with CaCl(2) absorbed water and gained weight with time, except for in the 24-h period. The addition of CaCl(2) to the WPC reduced its solubility. The addition of CaCl(2) increased the pH of WMTA in the immediate period and at 24 and 72 h and for WPC in the immediate period and at 24 h. The addition of CaCl(2) to WMTA and WPC reduced the setting times and solubility of both and increased the pH of cements in the initial periods. (J Endod 2009;35:550-554)

Reaction of rat connective tissue to implanted dentin tube filled with mineral trioxide aggregate, Portland cement or calcium hydroxide.

The subject of this study was to observe the rat subcutaneous connective tissue reaction to implanted dentin tubes filled with mineral trioxide aggregate, Portland cement or calcium hydroxide. The animals were sacrificed after 7 or 30 days and the undecalcified specimens were prepared for histological analysis with polarized light and Von Kossa technique for mineralized tissues. The results were similar for the studied materials. At the tube openings, there were Von Kossa-positive granules that were birefringent to polarized light. Next to these granulations, there was an irregular tissue like a bridge that was Von Kossa-positive. The dentin walls of the tubes exhibited in the tubules a structure highly birefringent to polarized light, usually like a layer and at different depths. The mechanism of action of the studied materials has some similarity.

Influence of addition of calcium oxide on physicochemical properties of Portland cement with zirconium or niobium oxide

Context: Calcium oxide (CaO) may be added to mineral trioxide aggregate (MTA) or Portland cement (PC) to improve physicochemical and biological properties. Aims: To evaluate the physicochemical properties of PC associated with radiopacifiers and CaO. Materials and Methods: MTA Angelus, PC + 30% zirconium oxide (Zr), or 30% niobium oxide (Nb) associated with 10 or 20% of CaO were evaluated. Gilmore needles were used to evaluate initial and final setting time. Compressive strength was evaluated after the periods of 24 hours and 21 days. pH was analyzed after 3, 12, 24 hours, 7, 14, 21 days. Solubility and flow tests were performed based on the ISO 6876. The data obtained were submitted to analysis of variance and Tukey tests (P ≤ 0.05). Results: The associations with 10% CaO showed greater strength that the associations with 20% CaO. The shortest initial setting time was observed for the association PC + Zr + 20% CaO and MTA. All the cements presented alkaline pH. The flow of all cements was similar. The highest solubility was found in the associations with 20% CaO. Conclusion: The addition of CaO to PC favored the alkaline property and the PC + Zr + 20% CaO presented setting time similar to MTA.

Biocompatibility and setting time of CPM-MTA and white Portland cement clinker with or without calcium sulfate

To evaluate the biocompatibility and the setting time of Portland cement clinker with or without 2% or 5% calcium sulfate and MTA-CPM. Twenty-four mice (Rattus norvegicus) received subcutaneously polyethylene tubes filled with Portland cement clinker with or without 2% or 5% calcium sulfate and MTA. After 15, 30 and 60 days of implantation, the animals were killed and specimens were prepared for microscopic analysis. For evaluation of the setting time, each material was analyzed using Gilmore needles weighing 113.5 g and 456.5 g, according to the ASTM specification Number C266-08 guideline. Data were analyzed by ANOVA and Tukey's test for setting time and Kruskal-Wallis and Dunn test for biocompatibility at 5% significance level. Histologic observation showed no statistically significant difference of biocompatibility (p>0.05) among the materials in the subcutaneous tissues. For the setting time, clinker without calcium sulfate showed the shortest initial and final setting times (6.18 s/21.48 s), followed by clinker with 2% calcium sulfate (9.22 s/25.33 s), clinker with 5% calcium sulfate (10.06 s/42.46 s) and MTA (15.01 s/42.46 s). All the tested materials showed biocompatibility and the calcium sulfate absence shortened the initial and final setting times of the white Portland cement clinker

Cement stabilization of runoff residuals: A study of stabilization/solidification of urban rainfall-runoff residuals in type 1 Portland cement by XRD and Si-29 NMR analysis

Urban rainfall-runoff residuals contain metals such as Cr, Zn, Cu, As, Pb and Cd and are thus reasonable candidates for treatment using Portland cement-based solidification-stabilization (S/S). This research is a study of S/S of urban storm water runoff solid residuals in Portland cement with quicklime and sodium bentonite additives. The solidified residuals were analyzed after 28 days of hydration time using X-ray powder diffraction (XRD) and solid-state Si-29 nuclear magnetic resonance (NMR) spectroscopy. X-ray diffraction (XRD) results indicate that the main cement hydration products are ettringite, calcium hydroxide and hydrated calcium silicates. Zinc hydroxide and lead and zinc silicates are also present due to the reactions of the waste compounds with the cement and its hydration products. Si-29 NMR analysis shows that the coarse fraction of the waste apparently does not interfere with cement hydration, but the fine fraction retards silica polymerization.

Chemical interaction between EVA and Portland cement hydration at early-age

Ethylene/vinyl acetate (EVA) copolymer. as latex or redispersable powder, is added to mortars and concrete to improve the fracture toughness, impermeability and bond strength to various substrates. The physical and chemical interactions were already proved after one day of hydration but during the first hour just the physical interaction was identified and some evidences of a chemical interaction. The aim of this paper was to evaluate the chemical interaction between EVA and Portland cement during the first hours of hydration in the thermogravimetric analysis. The results confirmed that the EVA hydrolyses in pH alkaline and consumes calcium ions from the solution, forming an organic salt (calcium acetate). reducing the calcium hydroxide content. And, its interaction occurred in the first 15 min of hydration. (C) 2009 Elsevier Ltd. All rights reserved.

Alpha-Tricalcium Phosphate Bone Cement in the Surgical Treatment of Open Mastoid Cavity

Hypothesis: This study aimed to evaluate the biocompatibility of alpha-tricalcium phosphate bone cement in the obliteration of the mastoid cavity in guinea pigs. Background: Treatment with open cavity mastoidectomy can present poor functional results in chronic otitis media with cholesteatoma, especially if the cavity is large. Partial or total obliteration of the cavity can overcome these problems. Alpha-tricalcium phosphate bone cement has physicochemical characteristics that suggest its potential in mastoid cavity obliteration. Materials and Methods: Twenty guinea pigs were studied. All animals underwent surgery involving the dorsal tympanic bulla. In the study group animals (n = 10), mastoid cavity obliteration was performed with alpha-tricalcium phosphate bone cement. In the control group animals (n = 10), the cavity was left unfilled. On postoperative day 60, the animals were sacrificed and studied for signs of rejection of the material and other complications. Temporal bones were removed for histopathological study, in which the type and degree of inflammatory response, as well as the degree of ossification, were analyzed. Results: The mortality rate was the same in both groups. Deaths were attributed to anesthetic complications in the initial postoperative period. In the animals that survived, there were no complications, and there was good healing of the incision in both groups. There were no clinical signs of rejection of the material, and the histopathological analysis of the cement group revealed no signs of foreign body reaction (inflammatory response). Conclusion: Alpha-tricalcium phosphate bone cement is biocompatible in the mastoid cavity of guinea pigs.

pH, Calcium Ion Release, and Setting Time of an Experimental Mineral Trioxide Aggregate-based Root Canal Sealer

Introduction: An experimental mineral trioxide aggregate sealer (MTAS) has been developed for use as a root canal sealer. The aim of this study was to evaluate the setting time, pH, and calcium ion release of MTAS compared with white Portland cement (CPB-40; Votorantin Cimentos, Camargo Correa SA, Pedro Leopoldo, MG, Brazil), white MTA Angelus (MTA; Angelus, Londrina, PR, Brazil), and AH Plus (Dentsply DeTrey, Konstanz, Germany). Methods: For the evaluation of setting time, each material was analyzed using Gilmore-type needles. Polyethylene tubes with the materials were immersed in distilled water for the measurement of pH (digital pH meter) and calcium release (atomic absorption spectrophotometry). The evaluations were performed at 3, 6, 12, 24, and 48 hours and 7, 14, and 28 days. Data were analyzed by analysis of variance and the Tukey test at 5% significance level. Results: MTAS showed higher calcium release at all experimental periods, a greater increase in pH up to 48 hours and the longest setting time. Conclusions: MTAS presented favorable properties for its indication as a root canal sealer. (J Endod 2011;37:844-846)

Evaluation of pH and Calcium Ion Release of Root-end Filling Materials Containing Calcium Hydroxide or Mineral Trioxide Aggregate

Introduction: To evaluate calcium ion release and pH of Sealer 26 (S26) (Dentsply, Rio de Janeiro, RJ, Brazil), white mineral trioxide aggregate (MTA), Endo CPM Sealer (CPM1) (EGEO SRL Bajo licencia MTM Argentina SA, Buenos Aires, Argentina), Endo CPM Sealer in a thicker consistency (CPM 2), and zinc oxide and eugenol cement (ZOE). Methods: Material samples (n = 10) were placed in polyethylene tubes and immersed in 10 mL of distilled water. After 3, 6,12,24, and 48 hours and 7,14, and 28 days, the water pH was determined with a pH meter, and calcium release was assessed by atomic absorption spectrophotometry. An empty tube was used as the control group. Results: The control group presented a pH value of 6.9 at all studied periods and did not show the presence of calcium ion. S26 presented greater hydroxyl ion release up to 12 hours (p < 0.05). From 24 hours until 28 days, S26, MTA, CPM1, and CPM2 had similar results. in ail periods, ZOE presented the lowest hydroxyl ion release. CPM1, followed by CPM2, released the most calcium ions until 24 hours (p < 0.05). Between 48 hours and 7 days, CPM1 and CPM2 had the highest release. A greater calcium ion release was observed for CPM2, followed by CPM1 at 14 days and for S26, CPM1, and CPM2 at 28 days. ZOE released the least calcium ions in all periods. Conclusion: Sealer 26, MTA, and Endo CPM sealer at normal or thicker consistency release hydroxyl and calcium ions. Endo CPM sealer may be an alternative as root-end filling material. (J Endod 2009;35:1418-1421)

Evaluation of pH and calcium ion release of new root-end filling materials

Objective. The purpose of this study was to evaluate the pH and calcium ion release of 6 materials used for root-end filling and perforation repair. Study design. Gray ProRoot MTA, gray MTA-Angelus, white MTA-Angelus, and CPM were compared to 2 experimental ones: MTA-exp, also based in Portland cement with a modified mixing liquid, and MBPc, an epoxy-resin based cement containing calcium hydroxide. After 3, 24, 72, and 168 hours the water in which each sample had been immersed was tested to determine the ph and calcium ion release. Results. All the analyzed materials showed alkaline pH and capacity to release calcium ions; however, a tendency of reduction of these characteristics was noted for all the analyzed materials, except for the MBPc, which showed a slight increase of pH among the 3 initial periods. Conclusion. The results suggest that all materials investigated presented alkaline pH and ability of release of calcium ions. (Oral Surg Oral Med Oral Pathol Oral Radiol Endod 2009; 108: 135-139)

Radiopacity of Portland Cement Associated With Different Radiopacifying Agents

This study evaluated the radiopacity of Portland cement associated with the following radiopacifying agents: bismuth oxide, zinc oxide, lead oxide, bismuth subnitrate, bismuth carbonate, barium sulfate, iodoform, calcium tungstate, and zirconium oxide. A ratio of 20% radiopacifier and 80% white Portland cement by weight was used for analysis. Pure Portland cement and dentin served as controls. Cement/radiopacifier and dentin disc-shaped specimens were fabricated, and radiopacity testing was performed according to the ISO 6876/2001 standard for dental root sealing materials. Using Insight occlusal films, the specimens were radiographed near to a graduated aluminum stepwedge varying from 2 to 16 mm in thickness. The radiographs were digitized and radiopacity compared with the aluminum stepwedge using Digora software (Orion Corporation Soredex, Helsinki, Finland). The radiographic density data were converted into mmAl and analyzed statistically by analysis of variance and Tukey-Kramer test (alpha = 0.05). The radiopacity of pure Portland cement was significantly lower (p < 0.05) than that of dentin, whereas all cement/radiopacifier mixtures were significantly more radiopaque than dentin and Portland cement alone (p < 0.05). Portland cement/bismuth oxide and Portland cement/lead oxide presented the highest radiopacity values and differed significantly from the other materials (p < 0.05), whereas Portland cement/zinc oxide presented the lowest radiopacity values of all mixtures (p < 0.05). All tested substances presented higher radiopacity than that of dentin and may potentially be added to the Portland cement as radiopacifying agents. However, the possible interference of the radiopacifiers with the setting chemistry, biocompatibility, and physical properties of the Portland cement should be further investigated before any clinical recommendation can be done. (J Endod 2009,35:737-740)