Prospecção geofísica em ocorrência de cobre localizada na bacia sedimentar do Camaquã (RS)

Estudos de pesquisa mineral são fundamentais para o reconhecimento e a incorporação de novas reservas. Esse trabalho apresenta os resultados de aplicação do método geofísico da eletrorresistividade numa ocorrência mineralizada em carbonatos de cobre, por meio da técnica de caminhamento elétrico em arranjo azimutal. A área de estudos está inserida na bacia sedimentar do Camaquã, formada por um conjunto de unidades estratigráficas sedimentares e vulcanogênicas, onde são descritas diversas ocorrências cupríferas. A presença de azurita e malaquita em fraturas e zonas de maior porosidade em arenito encaixante define a geologia local. Os modelos de inversão revelam anomalias circulares de resistividade moderada para até 25m abaixo da ocorrência aflorante e anomalias de baixa resistividade em profundidades abaixo de 25m, além de áreas adjacentes com alta resistividade. Indicadores de mineralização descritos para ocorrências de cobre estudadas, no âmbito da bacia sedimentar do Camaquã, ocorrem na área de estudos e permitem caracterização em termos de resistividade elétrica. Áreas com silicificação apresentam alta resistividade, enquanto que valores intermediários são atribuídos a zonas com carbonatação e, finalmente, áreas de baixa resistividade, provavelmente, indicam concentrações de sulfetos disseminados.

Seleção de métodos para avaliação do cobre disponível nos solos

Fez-se um estudo de seleção de métodos para cobre disponível, empregando-se trinta solos coletados na região de Jaboticabal, SP. Os solos utilizados pertencem aos seguintes grandes grupos: Solos Podzolizados de Lins e Marília, variação Lins e variação Marília, Latossolo Vermelho-Escuro fase arenosa, Latossolo Roxo, e Terra Roxa Estruturada. O cobre dos solos foi extraído através das seguintes soluções extratoras: CaCl2 0,5 M; Mg02 2,0 N; CH3COONH4 1,0 N1 pH 6,0 e pH 4,8; HCl 0,05 N e O,1 N; H2SO4 0,05 N; DTPA 0,005 M pH 7,3 e pH 6,0; EDTA 0,01 M + (NH4)2CO3 1,0 MpH 8,6; EDTA 0,02 M + CH3C0011 0,5 M + CH3COONH4 0,5 M pH 4,65 (AAAc-EDTA); e Na2EDTA 1,0%. Foi realizado ensaio em casa de vegetação, e o milho (Zea mays L.) foi empregado como planta teste. Excluindo-se o extrator CaCl2 0,5 M, todos os demais apresentaram coeficientes de correlação entre cobre extraído do solo e o absorvido pelo milho, significativos e próximos uns dos outros. Assim, com base também em parâmetros como o coeficiente de variação, o coeficiente angular e a praticidade do método, pode-se indicar um dos seguintes extratores para a avaliação do cobre disponível dos solos: DTPA 0,005 M pH 7,3, HCl 0,1 N e Na2EDTA 1,0%.

Teores de cobre, ferro, manganês e zinco no fígado e pâncreas de caprinos semi-confinados e confinados

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Biossorção de cobre, manganês e cádmio por biomassas de Saprolegnia subterranea(Dissmann) R.L. Seym. e Pythium torulosumCoker & P. Patt. (Oomycetes)

Dried biomass of the zoosporic fungi Saprolegnia subterranea and Pythium torulosum was evaluated for copper, manganese and cadmium biosorption from aqueous solutions using the "q" (mg of adsorbed metal per g of biomass) and the "R%" (percent removal) indices. The highest q values were observed when the biomass was placed in contact with high metal concentrations, whereas the highest R% values were observed at low concentrations (p< 0.05). S. subterranea SPC 1244 biomass surpassed the others for copper biosorption (q = 7.48 mg/ g; R% = 49.03), P. torulosum SPC 1425 biomass was the best for manganese biosorption (q = 4.13 mg/g; R% = 26.71), and S. subterranea SPC 1431 biomass was the best for cadmium biosorption (q = 6.75 mg/g; R% = 42.26). This is the first report on copper, manganese and cadmium biosorption by the biomass of these zoosporic fungi, indicating the potential to remove ions from diluted solutions.

Estudo das alterações lineares na região cervical de blocos M.O.D. fundidos em liga de cobre alumínio, segundo as técnicas de expansão higroscópica e térmica.

The authors studied linear alterations processed on copper-aluminum casten MOD blocks, obtained from two expansion techniques (termic and hygroscopic by immersion). UNITERMS: Investment expansion. Thermic expansion. Hygroscopic expansion. Casten Technique.

Rugosidade superficial de ligas com alto conteúdo de cobre, em função do aquecimento acima da temperatura de fusão.

Being the surface roughness a fundamental property in the fit of the castings, it was determined the roughness of 5 high-copper casting alloys, according to the heating over their melting temperature. That way, the specimens made with smooth plastic in the shape of a rectangular plate, 2 mm x 7 mm x 11 mm were invested into a cristobalite investment. After heating and elimination on the plastic, the molds were filled by 3 g of molten alloy, casted in a electrical casting machine at the casting temperature at 25 degrees C and 50 degrees C overheating. The surface roughness was measured in a roughness analyser, Talysurf. As a result, it was verified that there is a variation of surface roughness among the alloys tested, and the heating of the alloys until 50 degrees C over the melting temperature does not interfere in the roughness.

Efeito das técnicas de fusão sobre a fluidez de ligas do sistema cobre-alumínio.

It was evaluated the castability of four copper-aluminium alloy according the melting casting method used. The specimens were made using polyester mesh screen, with 11 x 11 filaments of 0.26 mm thick, fixed along of two adjacent edges in wax bar, with the sprue attached at their junction. The alloys were in an electrical casting machine and a centrifugal casting machine with an air/gas torch. The castability values were obtained by the percentage of completed segments of the resulting cast alloy screen. It was verified that the use of the electrical casting machine produced higher castability values to the copper-aluminium alloys than those produced by a centrifugal casting machine with an air/gas torch.

Determinação de dureza de ligas de cobre, na forma como são recebidas e após a fundição, em função das técnicas de fusão.

It was evaluated the Vickers hardness of five high-copper casting alloys, in their original package form and after casting, according to the casting method used. That way, ten ingots, supplied by the manufacturers of each alloy, were included in self-curing acrylic resin, polished, numerated and submitted to Vickers hardness test at load of 200 g during 30 seconds. Afterwards the numerated ingots were removed from the acrylic resin and five of those were cast in an electrical casting machine and the other five in a centrifugal casting machine with an air/gas torch. The specimens obtained were included in self-curing acrylic resin, polished and submitted to Vickers hardness test. As a result it was verified that there is a variation of hardness among the alloys tested, and the use of the electrical casting machine produced lower hardness values than those produced when used the centrifugal casting machine with an air/gas torch. Also, there is a decrease of hardness of the cast alloys when they are tested in their original form and after casting.

Estudio de los procesos de corrosion de una aleacion metalica de cobre usada en odontologia

Corrosion phenomena in a dental copper-based alloy are experimentally studied using electrochemical techniques. Two heating sources, torch and induction, were used in the casting experiments. In the corrosion essays, the optimum casting cycle and the polarization curves were obtained. It was found that the heating sources have little influence on the corrosion processes of the metallic alloys studied.

Borohidreto complexos de cobre (I) contendo difosfinas. Caracterização espectroscópica e comportamento térmico

Tetrahydroborate complexes of copper (I) with bidentate phosphines, [Cu(η 2-BH 4)(dppm)] (1), [Cu(η 2-BH 4)(dppe)] (2), [Cu(η 2-BH 4)(cis-dppet)] (3) and [Cu(η 2-BH 4)(dppb)] (4) (dppm = bis(diphenylphosphino)methane; dppe = 1,2-bis(diphenylphosphino) ethane; cis-dppet = 1,2-cis(diphenylphosphino)ethene; dppb = 1,4-bis(diphenylphosphino)butane) were prepared and characterized by elemental analysis, infrared spectroscopy, NMR and thermogravimetric analysis. The IR data for 1-4 showed bands typical of a bidentate coordination of BH 4 group to the copper atom and the 31P{ 1H} NMR spectra indicated that the phosphorous atoms are chelating the metal centre. The thermal behavior of the compounds was investigated and suggested that their thermal stability is influenced by the phosphines. Their thermal stability decreased as follows: [Cu(η 2-BH 4)(dppe)] (2) > [Cu(η 2-BH 4)(dppm)] (1) > [Cu(η 2-BH 4)(dppb)] (4) > [Cu(η 2-BH 4)(cis-dppet)] (3). According to thermal analysis and X-ray diffraction patterns all compounds decomposed giving Cu(BO 2) 2, CuO, CuO 2 and Cu as final products.

Alterações hematológicas e histopatológicas em pacu, Piaractus mesopotamicus Holmberg, 1887 (Osteichthyes, Characidae), tratado com sulfato de cobre (CuSo4)

This paper evaluated the haematological and glycaemic parameters in Piaractus mesopotamicus (Osteichthyes, Characidae) infected with Monogenea Anacanthorus penilabiatus Boeger, Husak & Martins, 1995 (Dactylogyridae) after treatment with 0.50 mg/L and 1.00 mg/L of copper sulphate (CuSO4). The efficacy of the CuSO4 was observed in the first day after administration but not after eight, fifteen or thirty days. The histopathological analyses showed hyperplasia of the epithelium and circulatory changes in the gills. In the first day after treatment significant changes (P<0.05) in the total count of erythrocyte, leucocyte, mean corpuscular haemoglobin concentration (MCHC) were observed. The fishes treated with 0.50 mg/L showed decrease in the haemoglobin levels and in the percentage of neutrophils (P<0.05). The dose of 1.00 mg/L provoked increase of glycaemia but reduction in the lymphocytes percentage when compared with 0.50 mg/L in the 8th day. Fifteen days after 1.00 mg/L treatment, values of mean corpuscular volume (MCV) and special granulocitic cells (S.G.C.) percentage decreased. Nevertheless, increase of total leucocyte number was observed. Thirty days after treatment with 0.50 mg/L showed increased S.G.C. and treatment with 1.00 mg/L showed increased lymphocyte.

Desenvolvimento de um dispositivo para obtenção de monocristais de ligas à base de cobre

This paper describes the drawing, construction and optimization of a device, which can be used to obtain single crystals of different metallic materials with melting point from 550 to 1050°C. Components of ease obtaining and of low cost were used. The device was based on the modified Bridgman technique and it was used to obtain single crystals of copper-based alloys. The temperature axial profiles and a difference less then 1% in the temperature between the wall and the center of the ceramic tube in the critical region for obtaining single crystals of good quality indicated that the oven presents a good thermal stability. Single crystals of CuZnAl and CuAlAg alloys of good quality were growth and characterized using optical microscopy and Laüe X-ray back reflection.

Toxicidade aguda do sulfato de cobre e do extrato aquoso de folhas secas de nim para o caramujo (Pomacea canaliculata)

Snails can become an environmental and economic problem, causing substantial losses. The objective of this work was to estimate the acute toxicity of copper sulfate pentahydrate (CuSO4.5H2O) and the aqueous extract of dried neem leaves on snails (P. canaliculata) under laboratory conditions. In order to estimate the lethal concentration 50% (LC (I)50;96h), snails were exposed to six increasing copper sulfate concentrations (0.0; 0.01; 0.03; 0.05; 0.07 and 0.1 mg L-1) and six increasing concentrations of aqueous extract of dried neem leaves 0.0; 100; 125; 150; 175 and 200 mL aqueous extract of dried neem leaves L-1 water, equivalent to (0.0; 1.18; 1.47; 1.77; 2.06 and 2.36 mg azadirachtin L -1), in triplicate and one control treatment in an entirely random delineation. Estimated LC (I)50;96h, of copper sulfate was 0.02 mg copper sulfate L-1, with a 0.01 mg L-1 lower limit and a 0.03 mg L-1 upper limit. Estimated lethal concentration 50% of the aqueous extract of dried neem leaves was 142.75 mL L-1, equivalent to 1.68 mg L-1 of azadirachtine, with a 130.89 mL L-1 (1.54 mg L-1) low limit and 155.69 mL L-1 (1.83 mg L -1) as the upper limit.

El complejo de cobre de la Southern Perú

Incluye Bibliografía

Aplicação da metodologia de superfície de resposta na remediação de um solo arenoso contaminado artificialmente com cobre

Soil flushing is an alternative remediation technology for soils contaminated with heavy metals, which the main contaminant removing process consists in percolating an extraction solution. This work aimed to use the response surface methodology to point out combinations among the parameters of the extraction solution (Na2EDTA concentration, volume e pH) in order to reduce the concentration of copper in a sandy soil to risk levels lower than the intervention levels for exposure scenarios adopted by the Environmental Company of Sao Paulo State. Thus, a series of tests in leaching columns were carried out using a Fluvisol artificially contaminated (1257,3 mg kg-1). The tests were conducted in triplicate and setup a central composite rotatable design with 15 different parameters combinations of the extraction solution and one replicate in the center point. Using 5% significance level, the adjusted model (R2 = 0,98) indicated combinations of Na2EDTA concentration, pH and volume of the extraction solution which allow reduction of copper concentration below levels reported by environmental agency of Sao Paulo State for industrial, residential, agricultural or maximum exposure scenarios.