A moored underwater energy conservation system for profiling measurement

There is a need to obtain the hydrologic data including ocean current, wave, temperature and so on in the South China Sea. A new profiling instrument which does not suffer from the damage due to nature forces or incidents caused by passing ships, is under development to acquire data from this area. This device is based on a taut single point mid-water mooring system. It incorporates a small, instrumented vertically profiling float attached via an electromechanical cable to a winch integral with the main subsurface flotation. On a pre-set schedule, the instrument float with sensors is winched up to the surface if there is no strip passing by, which is defined by an on-board miniature sonar. And it can be immediately winched down to a certain depth if the sonar sensor finds something is coming. Since, because Of logistics, the area can only be visited once for a long time and a minimum of 10 times per day profiles are desired, energy demands are severe. To respond to these concerns, the system has been designed to conserve a substantial portion of the potential energy lost during the ascent phase of each profile and subsequently use this energy to pull the instrument down. Compared with the previous single-point layered measuring mode, it is advanced and economical. At last the paper introduces the test in the South China Sea.

Specification of optimum holistic building environmental and energy performance information to support informed decision making

Political drivers such as the Kyoto protocol, the EU Energy Performance of Buildings Directive and the Energy end use and Services Directive have been implemented in response to an identified need for a reduction in human related CO2 emissions. Buildings account for a significant portion of global CO2 emissions, approximately 25-30%, and it is widely acknowledged by industry and research organisations that they operate inefficiently. In parallel, unsatisfactory indoor environmental conditions have proven to negatively impact occupant productivity. Legislative drivers and client education are seen as the key motivating factors for an improvement in the holistic environmental and energy performance of a building. A symbiotic relationship exists between building indoor environmental conditions and building energy consumption. However traditional Building Management Systems and Energy Management Systems treat these separately. Conventional performance analysis compares building energy consumption with a previously recorded value or with the consumption of a similar building and does not recognise the fact that all buildings are unique. Therefore what is required is a new framework which incorporates performance comparison against a theoretical building specific ideal benchmark. Traditionally Energy Managers, who work at the operational level of organisations with respect to building performance, do not have access to ideal performance benchmark information and as a result cannot optimally operate buildings. This thesis systematically defines Holistic Environmental and Energy Management and specifies the Scenario Modelling Technique which in turn uses an ideal performance benchmark. The holistic technique uses quantified expressions of building performance and by doing so enables the profiled Energy Manager to visualise his actions and the downstream consequences of his actions in the context of overall building operation. The Ideal Building Framework facilitates the use of this technique by acting as a Building Life Cycle (BLC) data repository through which ideal building performance benchmarks are systematically structured and stored in parallel with actual performance data. The Ideal Building Framework utilises transformed data in the form of the Ideal Set of Performance Objectives and Metrics which are capable of defining the performance of any building at any stage of the BLC. It is proposed that the union of Scenario Models for an individual building would result in a building specific Combination of Performance Metrics which would in turn be stored in the BLC data repository. The Ideal Data Set underpins the Ideal Set of Performance Objectives and Metrics and is the set of measurements required to monitor the performance of the Ideal Building. A Model View describes the unique building specific data relevant to a particular project stakeholder. The energy management data and information exchange requirements that underlie a Model View implementation are detailed and incorporate traditional and proposed energy management. This thesis also specifies the Model View Methodology which complements the Ideal Building Framework. The developed Model View and Rule Set methodology process utilises stakeholder specific rule sets to define stakeholder pertinent environmental and energy performance data. This generic process further enables each stakeholder to define the resolution of data desired. For example, basic, intermediate or detailed. The Model View methodology is applicable for all project stakeholders, each requiring its own customised rule set. Two rule sets are defined in detail, the Energy Manager rule set and the LEED Accreditor rule set. This particular measurement generation process accompanied by defined View would filter and expedite data access for all stakeholders involved in building performance. Information presentation is critical for effective use of the data provided by the Ideal Building Framework and the Energy Management View definition. The specifications for a customised Information Delivery Tool account for the established profile of Energy Managers and best practice user interface design. Components of the developed tool could also be used by Facility Managers working at the tactical and strategic levels of organisations. Informed decision making is made possible through specified decision assistance processes which incorporate the Scenario Modelling and Benchmarking techniques, the Ideal Building Framework, the Energy Manager Model View, the Information Delivery Tool and the established profile of Energy Managers. The Model View and Rule Set Methodology is effectively demonstrated on an appropriate mixed use existing ‘green’ building, the Environmental Research Institute at University College Cork, using the Energy Management and LEED rule sets. Informed Decision Making is also demonstrated using a prototype scenario for the demonstration building.

Burrow architecture and digging activity in the Cape dune mole rat

While females are traditionally thought to invest more time and energy into parental care than males, males often invest more resources into searching and displaying for mates, obtaining mates and in male-male conflict. Solitary subterranean mammals perform these activities in a particularly challenging niche, necessitating energetically expensive burrowing to both search for mates and forage for food. This restriction presumably affects males more than females as the former are thought to dig longer tunnels that cover greater distances to search for females. We excavated burrow systems of male and female Cape dune mole rats Bathyergus suillus the, largest truly subterranean mammal, to investigate whether male burrows differ from those of females in ways that reflect mate searching by males. We consider burrow architecture (length, internal dimensions, fractal dimension of tunnel systems, number of nesting chambers and mole mounds on the surface) in relation to mating strategy. Males excavated significantly longer burrow systems with higher fractal dimensions and larger burrow areas than females. Male burrow systems were also significantly farther from one another than females were from other females' burrow systems. However, no sex differences were evident in tunnel cross-sectional area, mass of soil excavated per mound, number of mounds produced per unit burrow length or mass of soil excavated per burrow system. Hence, while males may use their habitat differently from females, they do not appear to differ in the dimensions of the tunnels they create. Thus, exploration and use of the habitat differs between the sexes, which may be a consequence of sex differences in mating behaviour and greater demands for food.

Impact of sward type, cutting date and conditioning temperature on mass and energy flows in the integrated generation of solid fuel and biogas from semi-natural grassland

Energy production from biomass and the conservation of ecologically valuable grassland habitats are two important issues of agriculture today. The combination of a bioenergy production, which minimises environmental impacts and competition with food production for land with a conversion of semi-natural grasslands through new utilization alternatives for the biomass, led to the development of the IFBB process. Its basic principle is the separation of biomass into a liquid fraction (press fluid, PF) for the production of electric and thermal energy after anaerobic digestion to biogas and a solid fraction (press cake, PC) for the production of thermal energy through combustion. This study was undertaken to explore mass and energy flows as well as quality aspects of energy carriers within the IFBB process and determine their dependency on biomass-related and technical parameters. Two experiments were conducted, in which biomass from semi-natural grassland was conserved as silage and subjected to a hydrothermal conditioning and a subsequent mechanical dehydration with a screw press. Methane yield of the PF and the untreated silage was determined in anaerobic digestion experiments in batch fermenters at 37°C with a fermentation time of 13-15 and 27-35 days for the PF and the silage, respectively. Concentrations of dry matter (DM), ash, crude protein (CP), crude fibre (CF), ether extract (EE), neutral detergent fibre (NDF), acid detergent fibre (ADF), acid detergent ligning (ADL) and elements (K, Mg, Ca, Cl, N, S, P, C, H, N) were determined in the untreated biomass and the PC. Higher heating value (HHV) and ash softening temperature (AST) were calculated based on elemental concentration. Chemical composition of the PF and mass flows of all plant compounds into the PF were calculated. In the first experiment, biomass from five different semi-natural grassland swards (Arrhenaterion I and II, Caricion fuscae, Filipendulion ulmariae, Polygono-Trisetion) was harvested at one late sampling (19 July or 31 August) and ensiled. Each silage was subjected to three different temperature treatments (5°C, 60°C, 80°C) during hydrothermal conditioning. Based on observed methane yields and HHV as energy output parameters as well as literature-based and observed energy input parameters, energy and green house gas (GHG) balances were calculated for IFBB and two reference conversion processes, whole-crop digestion of untreated silage (WCD) and combustion of hay (CH). In the second experiment, biomass from one single semi-natural grassland sward (Arrhenaterion) was harvested at eight consecutive dates (27/04, 02/05, 09/05, 16/05, 24/05, 31/05, 11/06, 21/06) and ensiled. Each silage was subjected to six different treatments (no hydrothermal conditioning and hydrothermal conditioning at 10°C, 30°C, 50°C, 70°C, 90°C). Energy balance was calculated for IFBB and WCD. Multiple regression models were developed to predict mass flows, concentrations of elements in the PC, concentration of organic compounds in the PF and energy conversion efficiency of the IFBB process from temperature of hydrothermal conditioning as well as NDF and DM concentration in the silage. Results showed a relative reduction of ash and all elements detrimental for combustion in the PC compared to the untreated biomass of 20-90%. Reduction was highest for K and Cl and lowest for N. HHV of PC and untreated biomass were in a comparable range (17.8-19.5 MJ kg-1 DM), but AST of PC was higher (1156-1254°C). Methane yields of PF were higher compared to those of WCD when the biomass was harvested late (end of May and later) and in a comparable range when the biomass was harvested early and ranged from 332 to 458 LN kg-1 VS. Regarding energy and GHG balances, IFBB, with a net energy yield of 11.9-14.1 MWh ha-1, a conversion efficiency of 0.43-0.51, and GHG mitigation of 3.6-4.4 t CO2eq ha-1, performed better than WCD, but worse than CH. WCD produces thermal and electric energy with low efficiency, CH produces only thermal energy with a low quality solid fuel with high efficiency, IFBB produces thermal and electric energy with a solid fuel of high quality with medium efficiency. Regression models were able to predict target parameters with high accuracy (R2=0.70-0.99). The influence of increasing temperature of hydrothermal conditioning was an increase of mass flows, a decrease of element concentrations in the PC and a differing effect on energy conversion efficiency. The influence of increasing NDF concentration of the silage was a differing effect on mass flows, a decrease of element concentrations in the PC and an increase of energy conversion efficiency. The influence of increasing DM concentration of the silage was a decrease of mass flows, an increase of element concentrations in the PC and an increase of energy conversion efficiency. Based on the models an optimised IFBB process would be obtained with a medium temperature of hydrothermal conditioning (50°C), high NDF concentrations in the silage and medium DM concentrations of the silage.

CARBON CREDITS AND ENERGY EFFICIENCY

International carbon credit markets are based in differences between developing and developed countries greenhouse gases emissions mitigation costs and technological limits faced by developed countries. Potential of energy efficiency measures to reduce fossil fuel usage in Brazilian industrial segments is assessed, and analysis of such potentials singles out those segments and regions more apt to generate carbon credits through Clean Development Mechanism (CDM) projects. Though there are currently few Brazilian CDM projects, their number may be significantly increased, which is a positive outcome. For this purpose, it is crucial that energy conservation programs estimate how CDM may improve their economic competitiveness.

Mobile Architecture and Built Environment Laboratory (MABEL) - a building performance evaluation tool

This paper describes the Mobile Architecture and Built Environment Laboratory (MABEL) and its application for systematic building performance evaluation for compliance testing, commissioning, strategic and operational facility management and continuous improvement in the built environment.

The first part of the paper introduces the application areas of on-site building performance evaluation and discusses the shortcomings in this regard in current practice. It emphasises the need for on-site investigations to generate information on 'as built performance' for the 'feedback' loop between design, operation and occupancy of new buildings, retrofit or adjustment.

The second part introduces the Energy-Comfort-Behaviour Framework for 'across-the-board' building evaluation and discusses MABEL's role in this scheme. MABEL's objectives, procedures and the performance measurement matrix are explained and discussed.

A case for a mobile architecture and built environment laboratory

Deakin University and other research and industry partners have recently won a grant for the establishment of a Mobile Architecture and Built Environment Laboratory (MABEL). MABEL provides the first means of integrated, on-site measurement of the key aspects of the built environment (power, sound, light and comfort) using the latest instrument technology. There exists an ongoing need to establish a versatile and comprehensive in-situ testing facility for built internal environments, for the provision of research, education, training and technology diffusion. The ability to make on-site measurements across the environmental spectrum is unique and important. Individual measurements might demonstrate improved lighting performance, reduced power consumption, and improved ventilation or better building acoustics. More importantly, an integrated perspective will address an interaction in terms of energy efficiency and overall occupant comfort. H is recognised that many of the parameters we can measure with existing instrumentation remain unresolved regarding their diagnostic significance on occupant health, comfort and productivity. Also, developed standards for in-situ measurement are at an emerging state, in the delivery of reliable and useful assessment methods. This paper discusses the inception and role of the MABEL facility for building research, learning and teaching.

Incorporation of a hybrid cooling system in water cooled power stations to reduce water and energy consumptions

Water shortage is a major problem facing the power industry in many nations around the world. The largest consumer of water in most power plants is the wet cooling tower. To assist water and energy saving for thermal power stations using conventional evaporative wet cooling towers, a hybrid cooling system is proposed in this paper. The hybrid cooling system may consists of all or some of an air pre-cooler, heat pump, heat exchangers, and adsorption chillers together with the existing cooling tower. The hybrid cooling system described in the paper, consisting of a metal hydride heat pump operating in conjunction with the existing wet cooling tower, is capable of achieving water saving by reducing the temperature of warm water entering the cooling tower. Cooler inlet water temperatures effectively reduce the cooling load on existing towers. This will ultimately reduce the amount of water lost to the air by evaporation whilst still achieving the same cooling output. At the same time, the low grade waste energy upgraded by the metal hydride heat pump, in the process of cooling the water, can be used to replace the bleed of steam for the lower stage feed heaters which will increase overall cycle efficiency.

Climate change sensitivity of comfort and energy performance criteria for offices

The climate change scenarios of the Intergovernmental Panel on Climate Change (IPCC) predict a significant increase in temperatures over the next decades. Architecture and building occupants have to respond to this change, but little information is currently available in how far the predicted changes are likely to affect comfort and energy performance in buildings. This study therefore investigates the climate change sensitivity of the following parameters: adaptive thermal comfort according to Ashrae Standard 55 and EN 15251, energy consumption, heating and cooling loads, and length of heating and cooling periods. The study is based on parametric simulations of typical office room configurations in the context of Athens, Greece. They refer to different building design priorities and account for different occupant behaviour by using an ideal and worst case scenario. To evaluate the impact of the climate change, simulations are compared based on a common standard weather data set for Athens, and a generated climate change data set for the IPCC A2 scenario. The results show a significant impact of the climate change on all investigated parameters. They also indicate that in this context the optimisation of comfort and energy performance is likely to be related to finding the best possible balance between building (design) and occupant behaviour and other contextual influences, rather than a straightforward optimisation of separated single parameters.

Internal Architecture and Population Size of Acromyrmex subterraneus molestans (Hymenoptera, Formicidae) Nests: Comparison Between a Rural and an Urban Area

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Urban sprawl and energy use for transportation in the largest Brazilian cities

A study of the relationships between the amount of energy consumed for transportation purposes and a few selected variables related to urban form and socioeconomic characteristics of some of the largest Brazilian cities is conducted in this work. The studied cities include all 27 state capitals regardless of their size and population and 184 urban areas each with more than 20,000 inhabitants located in the state of São Paulo. Two different techniques were applied for data analyses: a more traditional regression analysis approach and artificial neural networks. In general, the results found in the analyses conducted here support the assumption that urban sprawl increases the energy use for transportation. In the case of the 27 state capitals, the analysis indicated that two spatial variables have a strong impact on the energy consumed for urban transportation: urban density and the ratio between the longest distances in the east-west and north-south directions. In the case of the 184 urbanized areas we also reached a similar conclusion. In that case, however, income and employment level apparently have a stronger influence on the amount of energy consumed. The results of the present study stress the importance of physical planning in developing country cities in order to reduce energy use for transportation. © 2007 International Energy Initiative, Inc.

Modeling of hydraulic and energy efficiency indicators for water supply systems

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)