Graphene and graphene oxide as effective adsorbents toward anionic and cationic dyes

In the present study, exfoliated graphene oxide (EGO) and reduced graphene oxide (rGO) have been used for the adsorption of various charged dyes such as methylene blue, methyl violet, rhodamine B, and orange G from aqueous solutions. EGO consists of single layer of graphite decorated with oxygen containing functional groups such as carboxyl, epoxy, ketone, and hydroxyl groups in its basal and edge planes. Consequently, the large negative charge density available in aqueous solutions helps in the effective adsorption of cationic dyes on EGO while the adsorption is negligible for anionic dyes. On the other hand, rGO that has high surface area does not possess as high a negative charge and is found to be very good adsorbent for anionic dyes. The adsorption process is followed using UV-Visible spectroscopy, while the material before and after adsorption has been characterized using physicochemical and spectroscopic techniques. Various isotherms have been used to fit the data, and kinetic parameters were evaluated. Raman and FT-IR spectroscopic data yield information on the interactions of dyes with the adsorbent. (C) 2011 Elsevier Inc. All rights reserved.

A cascaded discharge plasma-adsorbent technique for engine exhaust treatment

A cascaded system of electrical discharges (non-thermal plasma) and adsorption process was investigated for the removal of oxides of Nitrogen (NOx) and total hydrocarbons (THC) from an actual diesel engine exhaust. The non-thermal plasma and adsorption processes were separately studied first and then the cascaded process was studied. In this study, different types of adsorbents were used. The NOx removal efficiency was higher with plasma-associated adsorption (cascaded) process compared to the individual processes and the removal efficiency was found almost invariant in time. When associated by plasma, among the adsorbents studied, activated charcoal and MS-13X were more effective for NOx and THC removal respectively. The experiments were conducted at no load and at 50% load conditions. The plasma reactor was kept at room temperature throughout the experiment, while the temperature of the adsorbent reactor was varied. A relative comparison of adsorbents was discussed at the end.

Electrochemical, gravimetric and quantum chemical analysis of mild steel corrosion inhibition by colchicine in 1 M HCl medium

The inhibition effect of colchicine (CC) on mild steel (MS) corrosion in 1 M HCl solution has been investigated by electrochemical techniques such as electrochemical impedance spectroscopy, potentiodynamic polarization, chronoamperometry and also by the gravimetric method. Polarization studies showed that CC acts as mixed type corrosion inhibitor. The inhibitor adsorption process in the MS/CC/HCl system was studied at different temperatures (303-333 K). The adsorption of CC on MS surface is an exothermic process and obeys the Langmuir adsorption isotherm. Based on potential of zero charge values and quantum chemical parameters, the mechanism of adsorption has been proposed.

Ab Initio Study Of Zno-Based Gas-Sensing Mechanisms: Surface Reconstruction And Charge Transfer

Density functional theory (DFT) calculations were employed to explore the gas-sensing mechanisms of zinc oxide (ZnO) with surface reconstruction taken into consideration. Mix-terminated (10 (1) over bar0) ZnO surfaces were examined. By simulating the adsorption process of various gases, i.e., H-2, NH3, CO, and ethanol (C2H5OH) gases, on the ZnO (10 (1) over bar0) surface, the changes of configuration and electronic structure were compared. Based on these calculations, two gas-sensing mechanisms were proposed and revealed that both surface reconstruction and charge transfer result in a change of electronic conductance of ZnO. Also, the calculations were compared with existing experiments.

Estudo de adsorção de ácidos naftênicos a partir de correntes de hidrocarbonetos

Ácidos naftênicos correspondem à complexa mistura de ácidos carboxílicos presentes no petróleo, responsáveis diretamente pela sua acidez e pela sua corrosividade em fase líquida durante o refino. Tais compostos também estão presentes nas frações destiladas do petróleo, causando diversos problemas na qualidade final do produto. Uma possível forma de remover esses ácidos das frações destiladas é através da adsorção em materiais porosos. Contudo, os resultados até então apresentados indicam que resinas trocadoras de íons seriam os melhores adsorventes destes compostos, o que poderia aumentar o custo do processo e diminuir sua viabilidade. Neste trabalho, dois adsorventes comerciais (argila e alumina ativada) foram caracterizados por diversas técnicas físico-químicas e avaliados quanto à sua capacidade de remover os ácidos naftênicos de frações médias e pesadas de petróleo. Avaliou-se, ainda, para fins de comparação, o comportamento de ácidos naftênicos comerciais em óleos sintéticos preparados com óleo mineral. Em complementação, a corrosividade do aço carbono nos meios estudados foi também verificada. A argila apresentou maior afinidade com os ácidos naftênicos, tendo capacidade de adsorção superior e cinética de processo ligeiramente mais rápida às da alumina para as cargas sintéticas. No entanto, em virtude da maior concorrência pelos sítios de adsorção, apresentada pelos outros componentes presentes em óleos reais, observou-se uma perda na eficiência para estas amostras. Neste caso, a alumina apresentou melhores resultados. Embora ambos adsorventes tenham apresentado boa capacidade de remoção do soluto, a resina trocadora de íons ainda apresentou resultado mais eficaz para as amostras reais. Nas condições desse estudo, a taxa de corrosão do aço nas amostras sintéticas e em duas das reais não foi significativa e apenas uma delas apresentou-se corrosiva (Óleo 1). No entanto, a remoção dos ácidos naftênicos por adsorção conseguiu reduzir a taxa de corrosão neste meio em até 99%

Degradação de corantes têxteis ácidos e reativos por fotocatálise heterogênea, usando TiO2 como fotocatalisador

A indústria têxtil tem como característica a geração de grandes volumes de resíduos, principalmente corantes oriundos do tingimento de fios e tecidos. Os tratamentos convencionais de efluentes têxteis são ineficazes na degradação da maioria dos corantes. A fotocatálise heterogênea vem surgindo como alternativa promissora no tratamento desses poluentes. Neste trabalho, estudou-se a degradação fotocatalítica de duas soluções, simuladas em laboratório, compostas pelos corantes ácidos Blue 74, Red 51 e Yellow 3 (efluente I) e pelos reativos Black 5, Red 239 e Yellow 17 (efluente II), além de outros produtos químicos. Testes preliminares foram realizados para otimizar o pH e a massa de catalisador (TiO2) utilizados. Além da fotocatálise, experimentos de fotólise e adsorção também foram realizados. Através de espectrofotometria UV-VIS, verificou-se um descoramento por fotocatálise de 96% em 240 min e 97% em 30 min dos efluentes I e II, respectivamente. A mineralização do efluente I foi baixa (37%) e a do efluente II desprezível, nos tempos utilizados. No banho com corantes ácidos, foram realizadas ainda análises de toxicidade com sementes de alface (Lactuca sativa). A CE50 inicial estimada foi igual a 19,28 %, sendo a toxicidade totalmente removida após 63 min de processo fotocatalítico. A fotólise não obteve a mesma eficiência da fotocatálise, mostrando a importância do catalisador na degradação. A adsorção não foi significativa para os efluentes estudados. As cinéticas de degradação fotocatalítica de todos os corantes seguiram um modelo de pseudo-primeira ordem

Self-assembled monolayer of polyoxometalate on gold surfaces: Quartz crystal microbalance, electrochemistry, and in-situ scanning tunneling microscopy study

A new kind of inorganic self-assembled monolayer (SAM) was prepared by spontaneous adsorption of polyoxometalate anion, AsMo11VO404-, onto a gold surface from acidic aqueous solution. The adsorption process, structure, and electrochemical properties of the AsMo11VO404- SAM were investigated by quartz crystal microbalance (QCM), electrochemistry, and scanning tunneling microscopy (STM). The QCM data suggested that the self-assembling process could be described in terms of the Langmuir adsorption model, providing the value of the free energy of adsorption at -20 KJ mol(-1). The maximum surface coverage of the AsMo11VO404- SAM on gold surface was determined from the QCM data to be 1.7 x 10(-10) mol cm(-2), corresponding to a close-packed monolayer of AsMo11VO404- anion. The analysis of the voltammograms of the AsMo11VO404- SAM on gold electrode showed three pairs of reversible peaks with an equal surface coverage of 1.78 x 10(-10) mol cm(-2) for each of the peaks, and the value was agreed well with the QCM data. In-situ STM image demonstrated that the AsMo11VO404- SAM was very uniform and no aggregates or multilayer could be observed. Furthermore, the high-resolution STM images revealed that the AsMo11VO404- SAM on Au(lll) surface was composed of square unit cells with a lattice space of 10-11 Angstrom at +0.7 V (vs Ag\AgCl). The value was quite close to the diameter of AsMo11VO404- anion obtained from X-ray crystallographic study. The surface coverage of the AsMo11VO404- SAM on gold electrode estimated from the STM image was around 1.8 x 10(-10) mol cm(-2), which was consistent with the QCM and electrochemical results.

Recovery of silver (I) using a thiourea-modified chitosan resin

This work describes the preparation of a chelating resin from chemically modified chitosan. The resin was synthesized by using O-carboxymethylated chitosan to cross-link a polymeric Schiffs base of thiourea/glutaraldehyde and characterized by IR. Batch method was applied for testing the resin's adsorption behavior. Adsorption experiments showed the resin had good adsorption capacity and high selectivity for Ag(I) in aqueous solution. The maximum uptake of Ag(I) exhibited was 3.77 mmol/g, at pH 4.0. The results also indicated that the adsorption process was exothermic and fit well with the pseudosecond-order kinetic model. Ag(I) desorption could reach 99.23% using 0.5 M thiourea-2.0 M HCl solution. (C) 2010 Elsevier B.V. All rights reserved.

Observation of C60 film formation on a highly oriented pyrolitic graphite substrate via scanning tunnelling microscopy

We have investigated the early stages in the adsorption process of C60 molecules on a highly oriented pyrolitic graphite (HOPG) substrate. C60 powder was thermally evaporated in UHV of 10−8 Pa conditions onto a freshly cleaved HOPG surface. We did not observe individual fullerenes on the substrate for the case of short deposition times and low evaporation rates. However, small islands of C60 molecules with an fcc structure could be observed when the deposition rate was about 0.2 nm/min and the total thickness was above 1 nm. The islands did not grow in the vicinity of the HOPG steps. The typical lateral dimensions of these islands were of the order of a few hundred square nanometers, having thickness of up to five monolayers. We modified the shapes and positions of these islands by the STM tip, using a small (less than 1 V) bias voltage.

Thermodynamical studies of irreversible sorption of CO2 by Wyodak coal

Differential scanning calorimetry (DSC), temperature programmed desorption mass spectrometry (TPD-MS) and small angle neutron scattering (SANS) were used to investigate CO2 uptake by the Wyodak coal. The adsorption of carbon dioxide on Wyodak coal was studied by DSC. The exotherms evident at low temperatures are associated with the uptake of CO2 suggesting that carbon dioxide interacts strongly with the coal surface. The reduction in the value of the exotherms between the first and second runs for the Wyodak coal suggests that some CO2 is irreversibly bound to the structure even after heating to 200 °C DSC results also showed that adsorption of CO2 on the coal surface is an activated process and presumably at the temperature of the exotherms there is enough thermal energy to overcome the activation energy for adsorption. The adsorption process is instantly pursued by much slower diffusion of the gas molecules into the coal matrix (absorption). Structural rearrangement in coal by CO2 is examined by change in the glass transition temperature of coal after CO2 uptake at different pressures. The amount of gas dissolved in the coal increases with increasing CO2 pressure. TPD-MS showed that CO2 desorption from the Wyodak coal follows a first order kinetic model. Increase in the activation energy for desorption with pre-adsorbed CO2 pressure suggests that higher pressures facilitate the transport of CO2 molecules through the barriers therefore the amount of CO2 uptake by the coal is greater at higher pressures and more attempts are required to desorb CO2 molecules sorbed at elevated pressures. These conclusions were further confirmed by examining the Wyodak coal structure in high pressure CO 2 by SANS.

Treatment of aqueous effluents contaminated with ionic liquids

Ionic liquids are a class of solvents that, due to their unique properties, have been proposed in the past few years as alternatives to some hazardous volatile organic compounds. They are already used by industry, where it was possible to improve different processes by the incorporation of this kind of non-volatile and often liquid solvents. However, even if ionic liquids cannot contribute to air pollution, due to their negligible vapour pressures, they can be dispersed thorough aquatic streams thus contaminating the environment. Therefore, the main goals of this work are to study the mutual solubilities between water and different ionic liquids in order to infer on their environmental impact, and to propose effective methods to remove and, whenever possible, recover ionic liquids from aqueous media. The liquid-liquid phase behaviour of different ionic liquids and water was evaluated in the temperature range between (288.15 and 318.15) K. For higher melting temperature ionic liquids a narrower temperature range was studied. The gathered data allowed a deep understanding on the structural effects of the ionic liquid, namely the cation core, isomerism, symmetry, cation alkyl chain length and the anion nature through their mutual solubilities (saturation values) with water. The experimental data were also supported by the COnductor-like Screening MOdel for Real Solvents (COSMO-RS), and for some more specific systems, molecular dynamics simulations were also employed for a better comprehension of these systems at a molecular level. On the other hand, in order to remove and recover ionic liquids from aqueous solutions, two different methods were studied: one based on aqueous biphasic systems, that allowed an almost complete recovery of hydrophilic ionic liquids (those completely miscible with water at temperatures close to room temperature) by the addition of strong salting-out agents (Al2(SO4)3 or AlK(SO4)2); and the other based on the adsorption of several ionic liquids onto commercial activated carbon. The first approach, in addition to allowing the removal of ionic liquids from aqueous solutions, also makes possible to recover the ionic liquid and to recycle the remaining solution. In the adsorption process, only the removal of the ionic liquid from aqueous solutions was attempted. Nevertheless, a broad understanding of the structural effects of the ionic liquid on the adsorption process was attained, and a final improvement on the adsorption of hydrophilic ionic liquids by the addition of an inorganic salt (Na2SO4) was also achieved. Yet, the development of a recovery process that allows the reuse of the ionic liquid is still required for the development of sustainable processes.

Valorização de resíduos carbonosos de gasificação como precursores de materiais para adsorção de poluentes em fase aquosa

Tese de doutoramento, Energia e Ambiente (Energia e Desenvolvimento Sustentável), Universidade de Lisboa, Faculdade de Ciências, 2014

Développement d’outils analytiques pour la détection de biomolécules directement dans des fluides sanguins

Cette thèse porte sur le développement de biocapteurs basés sur la technique de résonance des plasmons de surface (SPR) pour effectuer des analyses directement dans un fluide sanguin n’ayant subi aucune purification ou dilution. L’ensemble des biocapteurs discutés exploiteront un instrument SPR portable développé dans le groupe du professeur Masson. Le premier volet de la thèse portera sur le processus d’interférence lié à l’adsorption non spécifique du sérum à la surface du capteur. L’analyse des biomolécules adsorbées sera effectuée en combinant la SPR à la spectrométrie de masse. Les informations obtenues seront exploitées pour la construction de biocapteurs adaptés à l’analyse en milieu sanguin. Un premier biocapteur développé ciblera la protéine antigène prostatique spécifique (APS) contenue dans le sérum servant de biomarqueur pour dépister le cancer de la prostate. Pour détecter les faibles concentrations de cette protéine directement dans le sérum, un matériel plasmonique microstructuré sera utilisé pour amplifier les signaux obtenus et sera recouvert d’une monocouche peptidique minimisant l’adsorption non spécifique du sérum. L’instrument SPR aura été adapté pour permettre également la détection simultanée de fluorescence. Un test ELISA sera ainsi effectué en parallèle du test SPR. Chacune des techniques fournira un contrôle pour la deuxième, tout en permettant de détecter le biomarqueur au niveau requis pour dépister la maladie. La combinaison des deux méthodes permettra aussi d’élargir la gamme dynamique du test de dépistage. Pour terminer, l’instrument SPR portable sera utilisé dans le cadre de détection de petites biomolécules ayant un potentiel thérapeutique directement dans un échantillon de sang. Des peptides ayant une activité anti-athérosclérotique pourront ainsi être détectés à même un échantillon de sang ni purifié ni dilué, et ce à des concentrations de l’ordre du micromolaire. Une modification de la microfluidique via l’introduction d’une membrane poreuse au cœur de celle-ci sera la clé permettant d’effectuer de telles analyses. La présente thèse met de l’avant de nouvelles stratégies et des modifications instrumentales permettant d’analyser des protéines et des petites molécules directement dans un échantillon non purifié de sérum ou de sang. Les modifications apportées au système fluidique, à l’instrument SPR et au niveau du biocapteur employé permettront d’effectuer des biodétections dans des matrices aussi complexes que les fluides sanguins. Les présents travaux mettent en lumière la capacité d’un instrument SPR/fluorescence portable à faire en 12 minutes la biodétection d’un marqueur du cancer de la prostate directement dans un échantillon de sérum. Finalement, on rapporte ici un des premiers articles où un biocapteur SPR est utilisé à même un échantillon de sang non-purifié pour faire des biodétections.

Ecotoxic Metal Records and its Degree of Geochemical Symphony in the Niche of Cochin Estuarine System- A Theraptic Perspective

The heavy metal contamination in the environment may lead to circumstances like bioaccumulation and inturn biomagnification. Hence cheaper and effective technologies are needed to protect the precious natural resources and biological lives. A suitable technique is the one which meets the technical and environmental criteria for dealing with a particular remediation problem and should be site-specific due to spatial and climatic variations and it may not economically feasible everywhere. The search for newer technologies for the environmental therapy, involving the removal of toxic metals from wastewaters has directed attention to adsorption, based on metal binding capacities of various adsorbent materials. Therefore, the present study aim to identify and evaluate the most current mathematical formulations describing sorption processes. Although vast amount of research has been carried out in the area of metal removal by adsorption process using activated carbon few specific research data are available in different scientific institutions. The present work highlights the seasonal and spatial variations in the distribution of some selected heavy metals among various geochemical phases of Cochin Estuarine system and also looked into an environmental theraptic/remedial approach by adsorption technique using activated charcoal and chitosan, to reduce and thereby controlling metallic pollution. The thesis has been addressed in seven chapters with further subdivisions. The first chapter is introductory, stating the necessity of reducing or preventing water pollution due to the hazardous impact on environment and health of living organisms and drawing it from a careful review of literature relevant to the present study. It provides a constricted description about the study area, geology, and general hydrology and also bears the major objectives and scope of the present study.