Wind plant interaction with series-compensated power systems

Wind power based generation has been rapidly growing world-wide during the recent past. In order to transmit large amounts of wind power over long distances, system planners may often add series compensation to existing transmission lines owing to several benefits such as improved steady-state power transfer limit, improved transient stability, and efficient utilization of transmission infrastructure. Application of series capacitors has posed resonant interaction concerns such as through subsynchronous resonance (SSR) with conventional turbine-generators. Wind turbine-generators may also be susceptible to such resonant interactions. However, not much information is available in literature and even engineering standards are yet to address these issues. The motivation problem for this research is based on an actual system switching event that resulted in undamped oscillations in a 345-kV series-compensated, typical ring-bus power system configuration. Based on time-domain ATP (Alternative Transients Program) modeling, simulations and analysis of system event records, the occurrence of subsynchronous interactions within the existing 345-kV series-compensated power system has been investigated. Effects of various small-signal and large-signal power system disturbances with both identical and non-identical wind turbine parameters (such as with a statistical-spread) has been evaluated. Effect of parameter variations on subsynchronous oscillations has been quantified using 3D-DFT plots and the oscillations have been identified as due to electrical self-excitation effects, rather than torsional interaction. Further, the generator no-load reactance and the rotor-side converter inner-loop controller gains have been identified as bearing maximum sensitivity to either damping or exacerbating the self-excited oscillations. A higher-order spectral analysis method based on modified Prony estimation has been successfully applied to the field records identifying dominant 9.79 Hz subsynchronous oscillations. Recommendations have been made for exploring countermeasures.

Visual Fixation for 3D Video Stabilization

Visual fixation is employed by humans and some animals to keep a specific 3D location at the center of the visual gaze. Inspired by this phenomenon in nature, this paper explores the idea to transfer this mechanism to the context of video stabilization for a handheld video camera. A novel approach is presented that stabilizes a video by fixating on automatically extracted 3D target points. This approach is different from existing automatic solutions that stabilize the video by smoothing. To determine the 3D target points, the recorded scene is analyzed with a stateof- the-art structure-from-motion algorithm, which estimates camera motion and reconstructs a 3D point cloud of the static scene objects. Special algorithms are presented that search either virtual or real 3D target points, which back-project close to the center of the image for as long a period of time as possible. The stabilization algorithm then transforms the original images of the sequence so that these 3D target points are kept exactly in the center of the image, which, in case of real 3D target points, produces a perfectly stable result at the image center. Furthermore, different methods of additional user interaction are investigated. It is shown that the stabilization process can easily be controlled and that it can be combined with state-of-theart tracking techniques in order to obtain a powerful image stabilization tool. The approach is evaluated on a variety of videos taken with a hand-held camera in natural scenes.

Language Learning in 3D Virtual World

Second Life (SL) is an ideal platform for language learning. It is called a Multi-User Virtual Environment, where users can have varieties of learning experiences in life-like environments. Numerous attempts have been made to use SL as a platform for language teaching and the possibility of SL as a means to promote conversational interactions has been reported. However, the research so far has largely focused on simply using SL without further augmentations for communication between learners or between teachers and learners in a school-like environment. Conversely, not enough attention has been paid to its controllability which builds on the embedded functions in SL. This study, based on the latest theories of second language acquisition, especially on the Task Based Language Teaching and the Interaction Hypothesis, proposes to design and implement an automatized interactive task space (AITS) where robotic agents work as interlocutors of learners. This paper presents a design that incorporates the SLA theories into SL and the implementation method of the design to construct AITS, fulfilling the controllability of SL. It also presents the result of the evaluation experiment conducted on the constructed AITS.

Chiral Templating Activity of Tris(bipyridine)ruthenium(II) Cation in the Design of Three-Dimensional (3D) Optically Active Oxalate-Bridged {[Ru(bpy) 3 ][Cu 2 x Ni 2(1 - x ) (C 2 O 4 ) 3 ]} n (0 ≤ x ≤ 1; bpy = 2,2‘-bipyridine): Structural, Optical, and Magnetic Studies

Three-dimensional oxalate-based {[Ru(bpy)3][Cu2xNi2(1-x)(ox)3]}n (0≤ x ≤ 1, ox = C2O42-, bpy = 2,2‘bipyridine) were synthesized. The structure was determined for x = 1 by X-ray diffraction on single crystal. The compound crystallizes in the cubic space group P4132. It shows a three-dimensional 10-gon 3-connected (10,3) anionic network where copper(II) has an unusual tris(bischelated) environment. X-ray powder diffraction patterns and their Rietveld refinement show that all the compounds along the series are isostructural and single-phased. According to X-ray absorption spectroscopy, copper(II) and nickel(II) have an octahedral environment, respectively elongated and trigonally distorted. As shown by natural circular dichroism, the optically active forms of {[Ru(bpy)3][CuxNi2(1-x)(ox)3]}n are obtained starting from resolved Δ- or Λ-[Ru(bpy)3]2+. The Curie−Weiss temperatures range between −55 (x = 1) and −150 K (x = 0). The antiferromagnetic exchange interaction thus decreases when the copper contents increases in agreement with the crystallographic structure of the compounds and the electronic structure of the metal ions. At low temperature, the compounds exhibit complex long-range ordered magnetic behavior.

3D-modeling of Mercury's solar wind sputtered surface-exosphere environment

The efficiency of sputtered refractory elements by H+ and He++ solar wind ions from Mercury's surface and their contribution to the exosphere are studied for various solar wind conditions. A 3D solar wind-planetary interaction hybrid model is used for the evaluation of precipitation maps of the sputter agents on Mercury's surface. By assuming a global mineralogical surface composition, the related sputter yields are calculated by means of the 2013 SRIM code and are coupled with a 3D exosphere model. Because of Mercury's magnetic field, for quiet and nominal solar wind conditions the plasma can only precipitate around the polar areas, while for extreme solar events (fast solar wind, coronal mass ejections, interplanetary magnetic clouds) the solar wind plasma has access to the entire dayside. In that case the release of particles form the planet's surface can result in an exosphere density increase of more than one order of magnitude. The corresponding escape rates are also about an order of magnitude higher. Moreover, the amount of He++ ions in the precipitating solar plasma flow enhances also the release of sputtered elements from the surface in the exosphere. A comparison of our model results with MESSENGER observations of sputtered Mg and Ca elements in the exosphere shows a reasonable quantitative agreement. (C) 2015 Elsevier Ltd. All rights reserved.

A multimodal tablet-based interface for designing and reviewing 3D engineering models

The ability to view and interact with 3D models has been happening for a long time. However, vision-based 3D modeling has only seen limited success in applications, as it faces many technical challenges. Hand-held mobile devices have changed the way we interact with virtual reality environments. Their high mobility and technical features, such as inertial sensors, cameras and fast processors, are especially attractive for advancing the state of the art in virtual reality systems. Also, their ubiquity and fast Internet connection open a path to distributed and collaborative development. However, such path has not been fully explored in many domains. VR systems for real world engineering contexts are still difficult to use, especially when geographically dispersed engineering teams need to collaboratively visualize and review 3D CAD models. Another challenge is the ability to rendering these environments at the required interactive rates and with high fidelity. In this document it is presented a virtual reality system mobile for visualization, navigation and reviewing large scale 3D CAD models, held under the CEDAR (Collaborative Engineering Design and Review) project. It’s focused on interaction using different navigation modes. The system uses the mobile device's inertial sensors and camera to allow users to navigate through large scale models. IT professionals, architects, civil engineers and oil industry experts were involved in a qualitative assessment of the CEDAR system, in the form of direct user interaction with the prototypes and audio-recorded interviews about the prototypes. The lessons learned are valuable and are presented on this document. Subsequently it was prepared a quantitative study on the different navigation modes to analyze the best mode to use it in a given situation.

An attitude-based reasoning strategy to enhance interaction with augmented objects

This paper describes a mobile-based system to interact with objects in smart spaces, where the offer of resources may be extensive. The underlying idea is to use the augmentation capabilities of the mobile device to enable it as user-object mediator. In particular, the paper details how to build an attitude-based reasoning strategy that facilitates user-object interaction and resource filtering. The strategy prioritizes the available resources depending on the spatial history of the user, his real-time location and orientation and, finally, his active touch and focus interactions with the virtual overlay. The proposed reasoning method has been partially validated through a prototype that handles 2D and 3D visualization interfaces. This framework makes possible to develop in practice the IoT paradigm, augmenting the objects without physically modifying them.

Experimental Prototype Merging Stereo Panoramic Video and Interactive 3D Content in a 5-sided CAVETM

Immersion and interaction have been identified as key factors influencing the quality of experience in stereoscopic video systems. An experimental prototype designed to explore the influence of these factors in 3D video applications is described here1. The focus is on the real-time insertion algorithm of new 3D models into the original video streams. Using this algorithm, our prototype is aimed to explore a new interaction paradigm ? similar to the augmented reality approach ? with 3D video applications.

MEDVIR: 3D visual interface applied to gene profile analisys.

The origins for this work arise in response to the increasing need for biologists and doctors to obtain tools for visual analysis of data. When dealing with multidimensional data, such as medical data, the traditional data mining techniques can be a tedious and complex task, even to some medical experts. Therefore, it is necessary to develop useful visualization techniques that can complement the expert’s criterion, and at the same time visually stimulate and make easier the process of obtaining knowledge from a dataset. Thus, the process of interpretation and understanding of the data can be greatly enriched. Multidimensionality is inherent to any medical data, requiring a time-consuming effort to get a clinical useful outcome. Unfortunately, both clinicians and biologists are not trained in managing more than four dimensions. Specifically, we were aimed to design a 3D visual interface for gene profile analysis easy in order to be used both by medical and biologist experts. In this way, a new analysis method is proposed: MedVir. This is a simple and intuitive analysis mechanism based on the visualization of any multidimensional medical data in a three dimensional space that allows interaction with experts in order to collaborate and enrich this representation. In other words, MedVir makes a powerful reduction in data dimensionality in order to represent the original information into a three dimensional environment. The experts can interact with the data and draw conclusions in a visual and quickly way.

User experience with immersive and interactive media = Experiencia de usuario en entornos 3D inmersivos e interactivos

Estudios recientes promueven la integración de estímulos multisensoriales en activos multimedia con el fin de mejorar la experiencia de usuario mediante la estimulación de nuevos sentidos, más allá de la tradicional experiencia audiovisual. Del mismo modo, varios trabajos proponen la introducción de componentes de interacción capaces de complementar con nuevas características, funcionalidades y/o información la experiencia multimedia. Efectos sensoriales basados en el uso de nuevas técnicas de audio, olores, viento, vibraciones y control de la iluminación, han demostrado tener un impacto favorable en la sensación de Presencia, en el disfrute de la experiencia multimedia y en la calidad, relevancia y realismo de la misma percibidos por el usuario. Asimismo, los servicios basados en dos pantallas y la manipulación directa de (elementos en) la escena de video tienen el potencial de mejorar la comprensión, la concentración y la implicación proactiva del usuario en la experiencia multimedia. El deporte se encuentra entre los géneros con mayor potencial para integrar y explotar éstas soluciones tecnológicas. Trabajos previos han demostrado asimismo la viabilidad técnica de integrar éstas tecnologías con los estándares actualmente adoptados a lo largo de toda la cadena de transmisión de televisión. De este modo, los sistemas multimedia enriquecidos con efectos sensoriales, los servicios interactivos multiplataforma y un mayor control del usuario sobre la escena de vídeo emergen como nuevas formas de llevar la multimedia immersiva e interactiva al mercado de consumo de forma no disruptiva. Sin embargo, existen numerosas interrogantes relativas a los efectos sensoriales y/o soluciones interactivas más adecuadas para complementar un contenido audiovisual determinado o a la mejor manera de de integrar y combinar dichos componentes para mejorar la experiencia de usuario de un segmento de audiencia objetivo. Además, la evidencia científica sobre el impacto de factores humanos en la experiencia de usuario con estas nuevas formas de immersión e interacción en el contexto multimedia es aún insuficiente y en ocasiones, contradictoria. Así, el papel de éstos factores en el potencial de adopción de éstas tecnologías ha sido amplia-mente ignorado. La presente tesis analiza el impacto del audio binaural, efectos sensoriales (de iluminación y olfativos), interacción con objetos 3D integrados en la escena de vídeo e interacción con contenido adicional utilizando una segunda pantalla en la experiencia de usuario con contenidos de deporte. La posible influencia de dichos componentes en las variables dependientes se explora tanto a nivel global (efecto promedio) como en función de las características de los usuarios (efectos heterogéneos). Para ello, se ha llevado a cabo un experimento con usuarios orientado a explorar la influencia de éstos componentes immersivos e interactivos en dos grandes dimensiones de la experiencia multimedia: calidad y Presencia. La calidad de la experiencia multimedia se analiza en términos de las posibles variaciones asociadas a la calidad global y a la calidad del contenido, la imagen, el audio, los efectos sensoriales, la interacción con objetos 3D y la interacción con la segunda pantalla. El posible impacto en la Presencia considera dos de las dimensiones definidas por el cuestionario ITC-SOPI: Presencia Espacial (Spatial Presence) e Implicación (Engagement). Por último, los individuos son caracterizados teniendo en cuenta los siguientes atributos afectivos, cognitivos y conductuales: preferencias y hábitos en relación con el contenido, grado de conocimiento de las tecnologías integradas en el sistema, tendencia a involucrarse emocionalmente, tendencia a concentrarse en una actividad bloqueando estímulos externos y los cinco grandes rasgos de la personalidad: extroversión, amabilidad, responsabilidad, inestabilidad emocional y apertura a nuevas experiencias. A nivel global, nuestro estudio revela que los participantes prefieren el audio binaural frente al sistema estéreo y que los efectos sensoriales generan un aumento significativo del nivel de Presencia Espacial percibido por los usuarios. Además, las manipulaciones experimentales realizadas permitieron identificar una gran variedad de efectos heterogéneos. Un resultado interesante es que dichos efectos no se encuentran distribuidos de forma equitativa entre las medidas de calidad y Presencia. Nuestros datos revelan un impacto generalizado del audio binaural en la mayoría de las medidas de calidad y Presencia analizadas. En cambio, la influencia de los efectos sensoriales y de la interacción con la segunda pantalla se concentran en las medidas de Presencia y calidad, respectivamente. La magnitud de los efectos heterogéneos identificados está modulada por las siguientes características personales: preferencias en relación con el contenido, frecuencia con la que el usuario suele ver contenido similar, conocimiento de las tecnologías integradas en el demostrador, sexo, tendencia a involucrarse emocionalmente, tendencia a a concentrarse en una actividad bloqueando estímulos externos y niveles de amabilidad, responsabilidad y apertura a nuevas experiencias. Las características personales consideradas en nuestro experimento explicaron la mayor parte de la variación en las variables dependientes, confirmando así el importante (y frecuentemente ignorado) papel de las diferencias individuales en la experiencia multimedia. Entre las características de los usuarios con un impacto más generalizado se encuentran las preferencias en relación con el contenido, el grado de conocimiento de las tecnologías integradas en el sistema y la tendencia a involucrarse emocionalmente. En particular, los primeros dos factores parecen generar un conflicto de atención hacia el contenido versus las características/elementos técnicos del sistema, respectivamente. Asimismo, la experiencia multimedia de los fans del fútbol parece estar modulada por procesos emociona-les, mientras que para los no-fans predominan los procesos cognitivos, en particular aquellos directamente relacionados con la percepción de calidad. Abstract Recent studies encourage the integration of multi-sensorial stimuli into multimedia assets to enhance the user experience by stimulating other senses beyond sight and hearing. Similarly, the introduction of multi-modal interaction components complementing with new features, functionalities and/or information the multimedia experience is promoted. Sensory effects as odor, wind, vibration and light effects, as well as an enhanced audio quality, have been found to favour media enjoyment and to have a positive influence on the sense of Presence and on the perceived quality, relevance and reality of a multimedia experience. Two-screen services and a direct manipulation of (elements in) the video scene have the potential to enhance user comprehension, engagement and proactive involvement of/in the media experience. Sports is among the genres that could benefit the most from these solutions. Previous works have demonstrated the technical feasibility of implementing and deploying end-to-end solutions integrating these technologies into legacy systems. Thus, sensorially-enhanced media, two-screen services and an increased user control over the displayed scene emerge as means to deliver a new form of immersive and interactive media experiences to the mass market in a non-disruptive manner. However, many questions remain concerning issues as the specific interactive solutions or sensory effects that can better complement a given audiovisual content or the best way in which to integrate and combine them to enhance the user experience of a target audience segment. Furthermore, scientific evidence on the impact of human factors on the user experience with these new forms of immersive and interactive media is still insufficient and sometimes, contradictory. Thus, the role of these factors on the potential adoption of these technologies has been widely ignored. This thesis analyzes the impact of binaural audio, sensory (light and olfactory) effects, interaction with 3D objects integrated into the video scene and interaction with additional content using a second screen on the sports media experience. The potential influence of these components on the dependent variables is explored both at the overall level (average effect) and as a function of users’ characteristics (heterogeneous effects). To these aims, we conducted an experimental study exploring the influence of these immersive and interactive elements on the quality and Presence dimensions of the media experience. Along the quality dimension, we look for possible variations on the quality scores as-signed to the overall media experience and to the media components content, image, audio, sensory effects, interaction with 3D objects and interaction using the tablet device. The potential impact on Presence is analyzed by looking at two of the four dimensions defined by the ITC-SOPI questionnaire, namely Spatial Presence and Engagement. The users’ characteristics considered encompass the following personal affective, cognitive and behavioral attributes: preferences and habits in relation to the content, knowledge of the involved technologies, tendency to get emotionally involved and tendency to get absorbed in an activity and block out external distractors and the big five personality traits extraversion, agreeableness, conscientiousness, neuroticism and openness to experience. At the overall level, we found that participants preferred binaural audio than standard stereo audio and that sensory effects increase significantly the level of Spatial Presence. Several heterogeneous effects were also revealed as a result of our experimental manipulations. Interestingly, these effects were not equally distributed across the quality and Presence measures analyzed. Whereas binaural audio was foud to have an influence on the majority of the quality and Presence measures considered, the effects of sensory effects and of interaction with additional content through the tablet device concentrate mainly on the dimensions of Presence and on quality measures, respectively. The magnitude of these effects was modulated by individual’s characteristics, such as: preferences in relation to the content, frequency of viewing similar content, knowledge of involved technologies, gender, tendency to get emotionally involved, tendency to absorption and levels of agreeableness, conscientiousness and openness to experience. The personal characteristics collected in our experiment explained most of the variation in the dependent variables, confirming the frequently neglected role of individual differences on the media experience. Preferences in relation to the content, knowledge of involved technologies and tendency to get emotionally involved were among the user variables with the most generalized influence. In particular, the former two features seem to present a conflict in the allocation of attentional resources towards the media content versus the technical features of the system, respectively. Additionally, football fans’ experience seems to be modulated by emotional processes whereas for not fans, cognitive processes (and in particular those related to quality judgment) prevail.

3D Maize Plant Reconstruction Based on Georeferenced Overlapping LiDAR Point Clouds

3D crop reconstruction with a high temporal resolution and by the use of non-destructive measuring technologies can support the automation of plant phenotyping processes. Thereby, the availability of such 3D data can give valuable information about the plant development and the interaction of the plant genotype with the environment. This article presents a new methodology for georeferenced 3D reconstruction of maize plant structure. For this purpose a total station, an IMU, and several 2D LiDARs with different orientations were mounted on an autonomous vehicle. By the multistep methodology presented, based on the application of the ICP algorithm for point cloud fusion, it was possible to perform the georeferenced point clouds overlapping. The overlapping point cloud algorithm showed that the aerial points (corresponding mainly to plant parts) were reduced to 1.5%–9% of the total registered data. The remaining were redundant or ground points. Through the inclusion of different LiDAR point of views of the scene, a more realistic representation of the surrounding is obtained by the incorporation of new useful information but also of noise. The use of georeferenced 3D maize plant reconstruction at different growth stages, combined with the total station accuracy could be highly useful when performing precision agriculture at the crop plant level.

Interacción combinada táctil 3D para manejo de colecciones de documentos

Actualmente existen varios dispositivos que aceptan gestos sobre superficies táctiles, sean celulares, tabletas, computadores, etc. a los cuales las personas se acostumbran rápidamente a su uso y los aceptan como herramientas necesarias en su vida. Del mismo modo existen algunas aplicaciones que manejan entornos en 3D, y permiten captar gestos realizados con las manos, cuerpo, cabeza. Estas técnicas se han desarrollado mucho por separado pero se ha podido evidenciar en base a los artículos revisados que no existen muchos estudios que combinen las aplicaciones táctiles con las 3D manejadas por gestos en el aire. El presente trabajo muestra un prototipo que permite la comunicación y coordinación entre dos aplicaciones, una que muestra documentos representados por esferas en una aplicación con interacción táctil desarrollada en Unity que funciona sobre Android, y una segunda aplicación desarrollada también en Unity que maneja un entorno 3D con el que se interactúa mediante gestos realizados en el aire. Luego de algunos intentos la interacción entre ambas aplicaciones fue lograda implementando comunicación por sockets entre la aplicación en el dispositivo Android y la aplicación 3D que se encuentra alojada en un computador con Windows 7. La captura de gestos en el aire se realiza mediante el sistema Tracking Tools desarrollado por la compañía Optitrack que captura los movimientos con cámaras infrarrojas y marcadores en los dedos. Este sistema envía los datos de los gestos a nuestra aplicación 3D. Estos equipos son de propiedad del laboratorio Decoroso Crespo de la Universidad Politécnica de Madrid. Una vez lograda la implementación e interacción entre las aplicaciones se han realizado pruebas de usabilidad con nueve estudiantes del Máster Universitario en Software y Sistemas de la Universidad Politécnica de Madrid. Cada uno ha respondido una serie de encuestas para poder obtener resultados sobre cuán usable es el prototipo, la experiencia del usuario y qué mejoras se podrían realizar sobre éste. En la parte final de este documento se presentan los resultados de las encuestas y se muestran las conclusiones y trabajo futuro.---ABSTRACT---Currently there are several devices that accept gestures on touch surfaces like phones, tablets, computers, etc. to which people quickly become accustomed to their use and accept them as necessary tools in their life. Similarly there are some applications that handle 3D environments and like televisions, holograms and allow capture gestures made with hands, body, and head. These techniques have been developed on a separated way but based on some research we may say that the are not many studies that combine touch with 3D applications handled by gestures in the air. This paper presents a prototype of the interaction of two issues of a 2D showing documents represented by spheres on a touch application developed in Unity that works on Android and allows communicating with the second application also developed in Unity that handles a 3D environment interaction of gestures made in air. After some attempts interaction was achieved by implementing communication sockets between the application on the Android device and 3D application that is hosted on a computer with windows 7, and gestures capturing in the air is done by the system Tracking Tools developed by the Optitrack company it captures movements with infrared cameras and markers on the fingers, which sends data to this application gestures, these equipment are owned by the Decoroso Crespo laboratory of the Polytechnic University of Madrid. Once achieved the interaction of applications has been conducted performance tests with ten students of the university master of the Universidad Politécnica de Madrid, each has answered a series of surveys to get results on how usable is the prototype, the user experience and that improvements could be made on this.

Detección automática con snakes y representación 3D sobre imágenes cerebrales

Comunicación presentada en la VI Conferencia de la Asociación Española para la Inteligencia Artificial (CAEPIA'95), Alicante, 15-17 noviembre 1995.

3D visual sensing of human hand for remote operation of a robotic hand

New low cost sensors and open free libraries for 3D image processing are making important advances in robot vision applications possible, such as three-dimensional object recognition, semantic mapping, navigation and localization of robots, human detection and/or gesture recognition for human-machine interaction. In this paper, a novel method for recognizing and tracking the fingers of a human hand is presented. This method is based on point clouds from range images captured by a RGBD sensor. It works in real time and it does not require visual marks, camera calibration or previous knowledge of the environment. Moreover, it works successfully even when multiple objects appear in the scene or when the ambient light is changed. Furthermore, this method was designed to develop a human interface to control domestic or industrial devices, remotely. In this paper, the method was tested by operating a robotic hand. Firstly, the human hand was recognized and the fingers were detected. Secondly, the movement of the fingers was analysed and mapped to be imitated by a robotic hand.

Towards a real-time 3D object recognition pipeline on mobile GPGPU computing platforms using low-cost RGB-D sensors

In this project, we propose the implementation of a 3D object recognition system which will be optimized to operate under demanding time constraints. The system must be robust so that objects can be recognized properly in poor light conditions and cluttered scenes with significant levels of occlusion. An important requirement must be met: the system must exhibit a reasonable performance running on a low power consumption mobile GPU computing platform (NVIDIA Jetson TK1) so that it can be integrated in mobile robotics systems, ambient intelligence or ambient assisted living applications. The acquisition system is based on the use of color and depth (RGB-D) data streams provided by low-cost 3D sensors like Microsoft Kinect or PrimeSense Carmine. The range of algorithms and applications to be implemented and integrated will be quite broad, ranging from the acquisition, outlier removal or filtering of the input data and the segmentation or characterization of regions of interest in the scene to the very object recognition and pose estimation. Furthermore, in order to validate the proposed system, we will create a 3D object dataset. It will be composed by a set of 3D models, reconstructed from common household objects, as well as a handful of test scenes in which those objects appear. The scenes will be characterized by different levels of occlusion, diverse distances from the elements to the sensor and variations on the pose of the target objects. The creation of this dataset implies the additional development of 3D data acquisition and 3D object reconstruction applications. The resulting system has many possible applications, ranging from mobile robot navigation and semantic scene labeling to human-computer interaction (HCI) systems based on visual information.