Dynamics of femtosecond laser pulse induced damage in multilayers

We report the single-shot damage thresholds of MgF2/ZnS onmidirectional reflector for laser pulse durations from 50 A to 900 fs. A coupled dynamic model is applied to study the damage mechanisms, in which we consider not only the electronic excitation of the material, but also the influence of this excitation-induced changes in the complex refractive index of material on the laser pulse itself. The results indicate that this feedback effect plays a very important role during the damage of material. Based on this model, we calculate the threshold fluences and the time-resolved excitation process of the multiplayer. The theoretical calculations agree well with our experimental results. (c) 2005 Elsevier B.V. All rights reserved.

Investigation of laser-induced damage on multi-layer dielectric gratings

We investigate mechanisms of laser induced damage thresholds (LIDTs) of multi-layer dielectric gratings (AIDG,). It is found that the laser damage thresholds of MDGs and unstructured dielectric multi-layer coatings (the substrate of MDG) are 3.15J/cm(2) and 9.32 J/cm(2), respectively, at 1064nm (12ns) with the Littrow angle 51.2 degrees and the TEM00 mode. The laser-induced damage mechanism of multi-layer dielectric is presented with the analysis of the following factors: The dominant factor is the pollution on the corrugated surface, which is induced by the complex manufacture process of multi-layer dielectric gratings; another is the electric field distribution along the corrugated surface. The third reason is due to the reduction in stoichiometry of oxide films, resulting from the manufacture process of etching.

Mechanism initiated by nanoabsorber for UV nanosecond-pulse-driven damage of dielectric coatings

A model of plasma formation induced by UV nanosecond pulselaser interaction with SiO2 thin film based on nanoabsorber is proposed. The model considers the temperature dependence of band gap. The numerical results show that during the process of nanosecond pulsed-laser interaction with SiO2 thin film, foreign inclusion which absorbs a fraction of incident radiation heats the surrounding host material through heat conduction causing the decrease of the band gap and consequently, the transformation of the initial transparent matrix into an absorptive medium around the inclusion, thus facilitates optical damage. Qualitative comparison with experiments is also provided. (C) 2008 Optical Society of America.

A study on damage caused to crustacean and finfish larvae during collection of Penaeus monodon (Fab.) postlarvae in the estuaries of Barguna, Bangladesh

A year round investigation in the estuaries of Barguna district revealed that for each Penaeus monodon postlarvae (PL), about 37 larvae of other shrimp species, 12 finfishes and 10 macrozooplankters are destroyed during the process of shrimp seed collection. Although abundance of P. monodon PL was not recorded throughout the year, a significant number of other shrimp spp., fin fishes including macrozooplankters are being damaged by the shrimp seed collectors. This indiscriminate destruction of aquatic organisms during P. monodon PL collection is serious threat to aquatic biodiversity.

3D numerical analysis of tunnelling induced damage: the influence of the alignment of a masonry building with the tunnel axis.

The development of infrastructure in major cities often involves tunnelling, which can cause damage to existing structures. Therefore, these projects require a careful prediction of the risk of settlement induced damage. The simplified approach of current methods cannot account for three-dimensional structural aspects of buildings, which can result in an inaccurate evaluation of damage. This paper investigates the effect of the building alignment with the tunnel axis on structural damage. A three-dimensional, phased, fully coupled finite element model with non-linear material properties is used as a tool to perform a parametric study. The model includes the simulation of the tunnel construction process, with the tunnel located adjacent to a masonry building. Three different type of settlements are included (sagging, hogging and a combination of them), with seven different increasing angles of the building with respect to the tunnel axis. The alignment parameter is assessed, based on the maximum occurring crack width, measured in the building. Results show a significant dependency of the final damage on the building and tunnel alignment.

Realization of extremely broadband quantum-dot superluminescent light-emitting diodes by rapid thermal-annealing process

The first demonstration, to our knowledge, of the creation of ultrabroadband superluminescent light-emitting diodes using multiple quantum-dot layer structure by rapid thermal-annealing process is reported. The device exhibits a 3 dB emission bandwidth of 146 nm centered at 984 mm with cw output power as high as 15 mW at room temperature corresponding to an extremely small coherence length of 6.6 mu m. (C) 2008 Optical Society of America.

Evolution of Localized Damage Zone in Heterogeneous Media

Evolution of localized damage zone is a key to catastrophic rupture in heterogeneous materials. In the present article, the evolutions of strain fields of rock specimens are investigated experimentally. The observed evolution of fluctuations and autocorrelations of strain fields under uniaxial compression demonstrates that the localization of deformation always appears ahead of catastrophic rupture. In particular, the localization evolves pronouncedly with increasing deformation in the rock experiments. By means of the definition of the zone with high strain rate and likely damage localization, it is found that the size of the localized zone decreases from the sample size at peak load to an eventual value. Actually, the deformation field beyond peak load is bound to suffer bifurcation, namely an elastic unloading part and a continuing but localized damage part will co-exist in series in a specimen. To describe this continuous bifurcation and localization process observed in experiments, a model on continuum mechanics is developed. The model can explain why the decreasing width of localized zone can lead stable deformation to unstable, but it still has not provided the complete equations governing the evolution of the localized zone.

Raman Spectroscopy of Irradiation Effect in Three Carbon Allotropes Induced by Low Energy B Ions

Irradiation efect in three carbon allotropes C60, diamond and highly oriented pyrolytic graphite (HOPG) induced by 170 keV B ions, mainly including the process of the damage creation, is investigated by means of Raman spectroscopy technique. The diferences on irradiation sensitivity and structural stability for C60, HOPG and diamond are compared. The analysis results indicate that C60 is the most sensitive for B ions irradiation,diamond is the second one and the structure of HOPG is the most stable under B ion irradiation. The damage cross sections ? of C60, diamond and HOPG deduced from the Raman spectra are 7.78×10−15 , 6.38×10−15 and1.31 × 10−15cm2, respectively.

Stress transfer and damage evolution simulations of fiber-reinforced polymer-matrix composites

The stress transfer from broken fibers to unbroken fibers in fiber-reinforced thermosetting polymer-matrix composites and thermoplastic polymer-matrix composites was studied using a detailed finite element model. In order to check the validity of this approach, an epoxy-matrix monolayer composite was used as thermosetting polymer-matrix composite and a polypropylene (PP)-matrix monolayer composite was used as thermoplastic polymer-matrix composite, respectively. It is found that the stress concentrations near the broken fiber element cause damage to the neighboring epoxy matrix prior to the breakage of other fibers, whereas in the case of PP-matrix composites the fibers nearest to the broken fiber break prior to the PP matrix damage, because the PP matrix around the broken fiber element yields. In order to simulate composite damage evolution, a Monte Carlo technique based on a finite element method has been developed in the paper. The finite element code coupled with statistical model of fiber strength specifically written for this problem was used to determine the stress redistribution. Five hundred samples of numerical simulation were carried out to obtain statistical deformation and failure process of composites with fixed fiber volume fraction.

Predicting impact damage, residual strength and crashworthiness of composite structures

The development of the latest generation of wide-body carbon-fibre composite passenger aircraft has heralded a new era in the utilisation of these materials. The premise of superior specific strength and stiffness, corrosion and fatigue resistance, is tempered by high development costs, slow production rates and lengthy and expensive certification programmes. Substantial effort is currently being directed towards the development of new modelling and simulation tools, at all levels of the development cycle, to mitigate these shortcomings. One of the primary challenges is to reduce the extent of physical testing, in the certification process, by adopting a ‘certification by simulation’ approach. In essence, this aspirational objective requires the ability to reliably predict the evolution and progression of damage in composites. The aerospace industry has been at the forefront of developing advanced composites modelling tools. As the automotive industry transitions towards the increased use of composites in mass-produced vehicles, similar challenges in the modelling of composites will need to be addressed, particularly in the reliable prediction of crashworthiness. While thermoset composites have dominated the aerospace industry, thermoplastics composites are likely to emerge as the preferred solution for meeting the high-volume production demands of passenger road vehicles. This keynote presentation will outline recent progress and current challenges in the development of finite-element-based predictive modelling tools for capturing impact damage, residual strength and energy absorption capacity of thermoset and thermoplastic composites for crashworthiness assessments.

Co-production and co-creation using self-service technology: the application of service-dominant logic

Research on how customers engage in the co-creation processes envisaged by the Servicedominant logic paradigm is currently limited and even less work has been published on frameworks for organizations to manage the co-creation process. This conceptual paper examines a particular aspect of co-creation: co-production as a result of the application of self-service technology (SST). We propose a conceptual framework for co-production, which emphasizes the need to understand productivity from the point of view of the customer, and demonstrate how this can be applied in both consumer (b2c) and interorganizational(b2b) contexts. We conclude that service organizations might benefit from clearly identifying co-production with task-performance, and co-creation with the valueattributing aspects of the customer service experience. Both aspects generate a range of design and management challenges for suppliers particularly the need to understand the cocreation process 'outputs' desired by customers and the full costs of moving away from person to person interaction.

The creation of euro area financial safety nets. Bruegel Working Paper 2012/09, July 2012

The financial crisis has exposed the need to devise stronger and broader international and regional safety nets in order to deal with economic and financial shocks and allow for countries to adjust. The euro area has developed several such mechanisms over the last couple of years through a process of trial and error and gradual enhancement and expansion. Their overall architecture remains imperfect and leaves areas of vulnerabilities. This paper provides an overview of the recent financial stability mechanisms and their various shortcomings and tries to brush the outline of a more comprehensive safety net architecture that would coherently address the banking, sovereign and external imbalances crises against both transitory and more permanent shocks. It aims to provide a roadmap for further improvements of the current mechanism and the creation of new devices including a banking resolution mechanism and amore powerfulmechanismto provide financial assistance addressing both the sovereign and external dimensions of the shocks thereby reducing the need for the ECB to fill the current void.

Opening the Windows of the Church to the World: The Creation of Nostra Aetate and Its Impact on the Christian-Jewish relationship

It is important to assert that this study is not a work to inflict guilt on the Catholics or Catholicism for their silence and indifference during the Holocaust. Instead, this study is about the process of moving on from the Catholic Church's past to where the Jewish community's theological existence was finally recognized and the Jewish people were no longer seen as the Others who killed Christ. This was, achieved through a church declaration titled Nostra Aetate (In Our Time). This study records the journey traversed by this declaration, the insurmountable odds it faced in its creation until its promulgation and the impact it has on the Jewish-Christian relationship.

Growth process in business and social entrepreneurship: the case of Brazil

The purpose of the dissertation is to investigate in depth the difference between the challenges social and business entrepreneurs face in the growth phase of their business in the particular environment of Brazil. This objective has been achieved through a two-steps methodology. The first step is a set of in-depth interviews carried out with industry experts such as professors, venture capitalists, consultants, fund managers or people involved in the support of growing startups (i.e. accelerators). These interviews allowed, first, to build a general perspective on the environment entrepreneurs operate into and to identify a list of challenges entrepreneurs face in the growth process of their business. This list was completed with the additional challenges identified in the previous literature. The second step of the methodology was to test the relevance of these challenges in the mind and experience of social and traditional entrepreneurs. A questionnaire was then submitted to 145 social and 286 traditional entrepreneurs. The results were statistically analyzed to test the relative relevance of these challenges for one group of entrepreneurs with respect to the other. The outcome of the analysis was significant. The most relevant challenges identified were, for both groups, taxation, bureaucracy, finding the right employees, creating effective teams, measuring firm performance and social value creation and obtaining funds. On the other side motivation, innovation, competition and lack of market space for growth represented the least relevant issues in the minds of entrepreneurs. This rank however did not differ significantly from social to traditional entrepreneurs. This testifies that in Brazil social and traditional entrepreneurs face the same set of challenges despite the widespread belief of the opposite.

Damages of spittlebug on sugarcane quality and fermentation process

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)