Kineettinen tarkastelu keskisakeusalueella toimivalle happivaiheelle

Työn tavoitteena oli tarkastella keskisakeudessa toimivan happidelignifioinnin kinetiikkaa ja vertailla sitä olemassa olevien kineettisten tutkimuksien kanssa. Lisäksi tutkittiin kuinka happivaiheen suodos vaikuttaa delignifiointiasteeseen sekä selektiivisyyteen. Työn kirjallisuusosassa perehdyttiin happidelignifioinnin kineettisiin malleihin, jotka on kehitetty ennustamaan alkalin, paineen, lämpötilan ja ajan vaikutusta ligniinin poistumiselle sekä hiilihydraattiketjujen katkeilulle. Delignifioituminen on nopeaa ensimmäisen kymmenen minuutin aikana ja hidastuu jäännösdelignifiointivaiheessa. Laboratoriotutkimuksissa selvitettiin kuinka prosessimuuttujat vaikuttavat kappaluvun ja viskositeetin muutokseen. Tuloksia tarkasteltiin lineaarisella regressioanalyysillä, jonka avulla muuttujien vaikutukset saadaan selkeästi esille. Happivaiheen ensimmäisessä vaiheessa suurin vaikutus delignifiointiasteeseen sekä viskositeetin alenemiseen on alkaliannoksella. Pienillä hapen annostuksella saavutettiin hyvä selektiivisyys, suurillakin alkaliannoksilla. Lämpötilan vaikutus on lähes olematon, kun paine on pieni. Kun paine kasvaa, kasvaa myös lämpötilan vaikutus delignifiointiasteeseen. Hiilihydraattien depolymerisoituminen lisääntyy lämpötilan kasvaessa lähes lineaarisesti, riippumatta paineesta. Hyvä loppuselektiivisyys saavutetaan kun ensimmäisen vaiheen selektiivisyys on hyvä. Ensimmäisessä vaiheessa saavutettiin hyvä selektiivisyys, kun alkali ei pääse kulumaan loppuun eikä delignifioituminen jatku liian pitkälle. Toisessa vaiheessa selektiivisyys säilyy parhaiten, kun lisättävä alkaliannos on pieni. Lämpötila ja paine vaikuttavat alkaliannokseen verrattuna hyvin vähän loppuselektiivisyyteen.

Platinum (II) and palladium (II) complexes with (N,N') and (C,N,N') ligands derived from pyrazole as anticancer and antimalarial agents: synthesis, characterization and in vitro activities

The study of the reactivity of three 1-(2-dimethylaminoethyl)-1H-pyrazole derivatives of general formula [1-(CH2)2NMe2}-3,5-R2-pzol] {where pzol represents pyrazole and Rdouble bond; length as m-dashH (1a), Me (1b) or Ph (1c)} with [MCl2(DMSO)2] (Mdouble bond; length as m-dashPt or Pd) under different experimental conditions allowed us to isolate and characterize cis-[M{κ2-N,N′-{[1-(CH2)2NMe2}-3,5-R2-pzol])}Cl2] {MMdouble bond; length as m-dashPtPt (2a-2c) or Pd (3a-3c)} and two cyclometallated complexes [M{κ3-C,N,N′-{[1-(CH2)2NMe2}-3-(C5H4)-5-Ph-pzol])}Cl] {Mdouble bond; length as m-dashPt(II) (4c) or Pd(II) (5c)}. Compounds 4c and 5c arise from the orthometallation of the 3-phenyl ring of ligand 1c. Complex 2a has been further characterized by X-ray crystallography. Ligands and complexes were evaluated for their in vitro antimalarial against Plasmodium falciparum and cytotoxic activities against lung (A549) and breast (MDA MB231 and MCF7) cancer cellular lines. Complexes 2a-2c and 5c exhibited only moderate antimalarial activities against two P. falciparum strains (3D7 and W2). Interestingly, cytotoxicity assays revealed that the platinacycle 4c exhibits a higher toxicity than cisplatin in the three human cell lines and that the complex 2a presents a remarkable cytotoxicity and selectivity in lung (IC50 = 3 μM) versus breast cancer cell lines (IC50 > 20 μM). Thus, complexes 2c and 4c appear to be promising leads, creating a novel family of anticancer agents. Electrophoretic DNA migration studies in presence of the synthesized compounds have been performed, in order to get further insights into their mechanism of action.

Koboltin ja nikkelin poisto sinkkisulfaattiliuoksesta ioninvaihdolla

Työssä tutkittiin kahden silikapohjaisen erotusmateriaalin soveltuvuutta nikkelin ja koboltin poistoon sinkkisulfaattiliuoksista. Suurin osa kokeista tehtiin ioninvaihtimella, jonka funktionaalinen ryhmä on iminodietikkahappo. Vertailuerotusmateriaalin toiminta perustui adsorptioon. Liuoksina käytettiin sekä autenttista prosessiliuosta että synteettistä ZnSO4-liousta. Ioninvaihtimen kestävyyskokeissa selvisi, että tutkittu ioninvaihdin kestää hyvin sekä 60 oC lämpötilan että happamia olosuhteita. Emäksisissä liuoksissa silikarunko ei kestä. Jo 0,1 M NaOH-liuos liuottaa merkittävästi hartsia vuorokauden aikana. Vaihtimen vetyionikapasiteetiksi saatiin titrauksella 2,3 mekv/g. Tasapainokokeilla saatiin selville, että ioninvaihdin on selektiivinen nikkelille sinkin suhteen ja että selektiivisyys kasvaa liuoksen pH:n laskiessa. Koboltille ioninvaihdin ei ole selektiivinen sinkin suhteen. Mikäli sinkin pitoisuus on tuhansia kertoja nikkelin pitoisuutta suurempi, ei ioninvaihtimen Ni-selektiivisyys riitä myöskään nikkelille. Synteettisillä ZnSO4-liuoksilla tehtyjen kolonnikokeiden perusteella havaittiin, että tutkitulla ioninvaihtimella voidaan laimeista ZnSO4-liuoksista poistaa nikkeliä selektiivisesti. Nikkelin eluointi onnistui helposti 1 M H2SO4:lla. Vertailukokeen perusteella oli ioninvaihtimen Ni/Zn-selektiivisyys referenssiadsorbentin Ni/Zn-selektiivisyyttä pienempi. Ioninvaihtokolonnin mallintaminen ei onnistunut riittävän hyvin kuvaamaan ioninvaihtimessa tapahtuvaa samanaikaista ioninvaihtoa ja adsorptiota. Sen sijaan kun kolonnissa oli vertailumateriaalina käytetty adsorbentti, saatiin kolonnikokeiden tulokset mallilla hyvin ennustettua.

Use of the dried blood spot sampling process coupled with fast gas chromatography and negative-ion chemical ionization tandem mass spectrometry: application to fluoxetine, norfluoxetine, reboxetine, and paroxetine analysis.

The objective of this work was to combine the advantages of the dried blood spot (DBS) sampling process with the highly sensitive and selective negative-ion chemical ionization tandem mass spectrometry (NICI-MS-MS) to analyze for recent antidepressants including fluoxetine, norfluoxetine, reboxetine, and paroxetine from micro whole blood samples (i.e., 10 microL). Before analysis, DBS samples were punched out, and antidepressants were simultaneously extracted and derivatized in a single step by use of pentafluoropropionic acid anhydride and 0.02% triethylamine in butyl chloride for 30 min at 60 degrees C under ultrasonication. Derivatives were then separated on a gas chromatograph coupled with a triple-quadrupole mass spectrometer operating in negative selected reaction monitoring mode for a total run time of 5 min. To establish the validity of the method, trueness, precision, and selectivity were determined on the basis of the guidelines of the "Société Française des Sciences et des Techniques Pharmaceutiques" (SFSTP). The assay was found to be linear in the concentration ranges 1 to 500 ng mL(-1) for fluoxetine and norfluoxetine and 20 to 500 ng mL(-1) for reboxetine and paroxetine. Despite the small sampling volume, the limit of detection was estimated at 20 pg mL(-1) for all the analytes. The stability of DBS was also evaluated at -20 degrees C, 4 degrees C, 25 degrees C, and 40 degrees C for up to 30 days. Furthermore, the method was successfully applied to a pharmacokinetic investigation performed on a healthy volunteer after oral administration of a single 40-mg dose of fluoxetine. Thus, this validated DBS method combines an extractive-derivative single step with a fast and sensitive GC-NICI-MS-MS technique. Using microliter blood samples, this procedure offers a patient-friendly tool in many biomedical fields such as checking treatment adherence, therapeutic drug monitoring, toxicological analyses, or pharmacokinetic studies.

Sulfaattimassan D/Q(EOP)D-valkaisimon optimointi

Työssä tutkittiin sulfaattisellutehtaan ECF-valkaisimon toimintaan vaikuttavia tekijöitä. Tavoitteena oli selvittää tekijöiden vaikutus massan laatuominaisuuksiin, valkaisimon kemikaalikustannuksiin ja klooridioksidin kulutukseen. Työn kirjallisuusosassa on tarkasteltu nykyaikaisen sulfaattisellutehtaan eri prosesseja. Erityistä huomiota on kiinnitetty sellun ECF-valkaisuun ja kyseisessä valkaisussa käytettäviin kemikaaleihin. Lisäksi on tarkasteltu TCF-valkaisua ja mahdollisuuksia sulkea sellutehtaan vesikiertoja. Kokeellisessa osassa selvitettiin Oy Metsä-Botnia Ab Joutsenon tehtaan kolmivaiheisen ECF-valkaisimon massan laatuominaisuuksiin, kustannuksiin ja klooridioksidin kulutukseen vaikuttavia tekijöitä. Tavoitteena oli vaikuttaa positiivisesti massan laatuominaisuuksiin valkaisun keinoin. Samalla pyrittiin minimoimaan valkaisusta aiheutuvia kemikaalikustannuksia ja vähentämään klooridioksidin kulutusta. Työssä käytettiin Taguchi-menetelmää. Tehdyn tutkimuksen myötä saatiin runsaasti tietoa mihin eri ominaisuuksiin tutkitut tekijät vaikuttivat. Metallien poistolla eli kelatoinnilla havaittiin olevan suuri merkitys hapettavan alkaliuuttovaiheen ja samalla koko valkaisimon toimintaan. Suurella kelatointiaineannoksella valkaisimon selektiivisyys ja tehokkuus paranivat. Muista tekijöistä happiannoksella havaittiin olevan vaikutusta vain massan paperiteknisiin ominaisuuksiin ja hiilihydraattien koostumukseen. Happiannoksen kasvattaminen paransi repäisyindeksiä ja vähensi massan jauhatustarvetta yli valkaisimon. Kyseisiin ominaisuuksiin vaikuttivat myös klooridioksidi ja sen toimintaolosuhteet. Kemikaalikustannuksiin vaikuttavista tekijöistä valkaisimon tulokapalla ja ensimmäisen klooridioksidivaiheen kemikaaliannoksella havaittiin olevan suuri merkitys. Samat tekijät vaikuttivat myös valkaisimon klooridioksidin kokonaiskulukseen.

Epäpuhtauksien poistaminen sinkkisulfaattiliuoksista käyttäen selektiivisiä ioninvaihtimia

Diplomityössä on tutkittu kuparin, koboltin, nikkelin ja kadmiumin poistamista sinkkisulfaattiliuoksista käyttäen uusia silikarunkoisia kelatoivia erotusmateriaaleja. Vertailukohteena on käytetty perinteisiä kaupallisia polymeerirunkoisia kelatoivia ioninvaihtohartseja. Laboratoriokokeissa selvitettiin erotusmateriaalien adsorptio- ja ioninvaihto-ominaisuuksia tasapaino- ja kolonnikokeilla. Silikarunkoisten erotusmateriaalien kemiallista kestävyyttä tutkittiin olosuhteissa, jotka vastaavat prosessisyklin eri vaiheita. Metallien adsorptiomekanismien selvittämiseksi erotusmateriaaleille tehtiin happo-emäs ja sulfaattititraukset. Tasapainokokeet osoittivat, että silikarunkoisilla erotusmateriaaleilla saatiin kupari erotettua väkevistä sinkkisulfaattiliuoksista polymeerirunkoisia kelatoivia ioninvaihtohartseja paremmin. Tutkituilla erotusmateriaaleilla ja ioninvaihtohartseilla ei havaittu merkittävää selektiivisyyttä koboltille, nikkelille tai kadmiumille sinkin ja kuparin läsnä ollessa. Kolonnikokeilla yritettiin löytää paras esikäsittely-lataus-eluointisykli kuparin talteenottoon väkevistä sinkkisulfaattiliuoksista silikarunkoisilla erotusmateriaaleilla. Kolonnikokeissa esikäsittely tehtiin laimealla NaOH:lla, jonka jälkeen petiin syötettiin hapanta sinkkisulfaattiliuosta. Eluointi onnistui hyvin laimealla rikkihapolla. Kolonnikokeiden tulokset osoittivat, että kupari on mahdollista erottaa väkevistä sinkkisulfaattiliuoksista. Silikarunkoisten erotusmateriaalien kemiallista kestävyyttä tutkittaessa havaittiin materiaalien kestävän hyvin happoja ja 60 oC:en lämpötilaa. Sitä vastoin alkaalisissa olosuhteissa tapahtui silikan liukenemista. Tutkituilla erotusmateriaaleilla havaittiin kuparin sitoutumista sekä ioninvaihtomekanismin avulla että sitoutuneena neutraalina suolana.

Estudi de noves estratègies encapsuladores d’antimalàrics i distribució de nanovectors polimèrics en Anopheles atroparvus

En aquest treball s’ha estudiat el comportament de compostos antimalàrics com els fàrmacs i els polímers en diferents situacions. Una de les barreres que ha estat identificada com a principal obstacle per a una millora de l’eficàcia dels compostos antimalàrics, és la limitació en la quantitat de fàrmac que pot ser encapsulada dins un liposoma, i que depèn de la seva solubilitat en medi aquós. Amb la inspiració de la descripció d’un nou tipus de nanocàpsules amb aplicacions oncològiques capaces d’encapsular grans quantitats de fàrmacs (protocells, Ashley et al., 2011). Els constructes formats per liposomes amb un nucli d’òxid de silici altament porós capaç de contenir el fàrmac, s’anomenen “protocells”, que en comparació als liposomes, tenen una major selectivitat i estabilitat, i permeten alliberar altes concentracions de droga directament al citosol de les cèl·lules cancerígenes. Aquest estudi es basa en la fabricació d’aquests nous nanovectors que continguin fàrmacs antimalàrics i té com a objectiu futur dirigir-los a eritròcits infectats per malària (pRBCs). Una altra part del treball és l’estudi de la distribució del polímer ISA-FITC en Anopheles atroparvus. Sabent que els polímers han estat utilitzats com a transportadors antimalàrics, es va pensar en l’opció d’eliminar el paràsit a dins del mateix mosquit, com una alternativa a tots el estudis realitzats fins ara centrats en les etapes d’infecció de l’hoste. Per aquest motiu es va idear l’experiment pensant en aquest polímer amb la intenció final de veure la seva localització en un mosquit Anopheles lliure del paràsit. OBJECTIUS: Determinació de la capacitat encapsuladora de tres tipus de nanopartícules, fabricades amb el mateix material però amb característiques de mida i càrrega diferents, incubant-les amb cinc fàrmacs antimalàrics. El blau de metilè, la primaquina, la cloroquina, la quinina i la curcumina, cadascun d’ells amb característiques de pH, solubilitat i estructura diferents. Alguns d’ells són fàrmacs que no s’han emprat en altres estudis degut a la seva toxicitat o elevada inespecificitat (la qual es pretén reduir un cop encapsulats en protocells). Construcció de “protocells” un cop determinada la millor nanopartícula encapsuladora i fàrmac candidat i determinació de la concentració de fàrmac que podien contenir, i el ritme d’alliberament d’aquest en PBS (simulant les condicions fisiològiques dels pRBCs). Estudi de la localització del polímer antimalàric ISA-FITC en l’anatomia del mosquit Anopheles Atroparvus. PROCEDIMENTS: Mètodes espectrofotomètrics Microscopia Cryo-electrònica de transmissió Microscopia confocal de fluorescència

Combined T2 -preparation and two-dimensional pencil-beam inner volume selection.

PURPOSE: To improve coronary magnetic resonance angiography (MRA) by combining a two-dimensional (2D) spatially selective radiofrequency (RF) pulse with a T2 -preparation module ("2D-T2 -Prep"). METHODS: An adiabatic T2 -Prep was modified so that the first and last pulses were of differing spatial selectivity. The first RF pulse was replaced by a 2D pulse, such that a pencil-beam volume is excited. The last RF pulse remains nonselective, thus restoring the T2 -prepared pencil-beam, while tipping the (formerly longitudinal) magnetization outside of the pencil-beam into the transverse plane, where it is then spoiled. Thus, only a cylinder of T2 -prepared tissue remains for imaging. Numerical simulations were followed by phantom validation and in vivo coronary MRA, where the technique was quantitatively evaluated. Reduced field-of-view (rFoV) images were similarly studied. RESULTS: In vivo, full field-of-view 2D-T2 -Prep significantly improved vessel sharpness as compared to conventional T2 -Prep, without adversely affecting signal-to-noise (SNR) or contrast-to-noise ratios (CNR). It also reduced respiratory motion artifacts. In rFoV images, the SNR, CNR, and vessel sharpness decreased, although scan time reduction was 60%. CONCLUSION: When compared with conventional T2 -Prep, the 2D-T2 -Prep improves vessel sharpness and decreases respiratory ghosting while preserving both SNR and CNR. It may also acquire rFoV images for accelerated data acquisition.

Regenerated cellulose ultrafiltration membranes in the treatment of pulp and paper mill process waters

Ultrafiltration (UF) is widely applied in different separation processes in the pulp and paper industry. The growing need to protect the environment, a lack of pure water and an interest in producing high-value chemicals from compounds present in process waters will probably lead to an increase in the use of UF in the pulp and paper industry. The efficiency and cost-effectiveness of a UF process depends on the applied membrane. The membrane should have a high and stable filtration capacity, a particular selectivity and a long operational lifetime. To meet these requirements a membrane should have a low fouling tendency. In addition, it should withstand the prevailing operational and chemical conditions. This thesis evaluates the performance and applicability of the regenerated cellulose (RC) membranes 00030T and C2 in the treatment of pulp and paper mill process waters based on the requirements above. The results demonstrated that both the tested RC membranes fulfilled well the requirement of high filtration capacity. In addition, in the filtration of a paper mill clear filtrate (CF) the RC membranes were not as greatly affected by variations in the CF quality as a polysulphone membrane. Furthermore, due to their extreme hydrophilicity and weak charge the fouling tendency of the membranes can be expected to be low in pulp and paper mill filtration applications. It is, however, known that fouling cannot be totally avoided even when the membrane is chosen very carefully. This study indicated that carbohydrates influenced negatively on permeability and caused fouling in the filtration of groundwood mill circulation water. Thus, a pre-treatment effectively reducing the amount of carbohydrates might help to maintain a stable capacity. However, the results of the thesis also showed that the removal of some of the possible foulants might just increase the harmful effect of others. Multivariate examination was useful in the understanding of the complicated factors causing the unstable capacity. The thesis also revealed that the 00030T and C2 membranes can be used at high pressure (max. tested pressure 12 bar). The C2 membrane, having a sponge-like substructure, was more pressure resistant, and its performance was more stable at high pressure compared to the UCO30T membrane containing macrovoids in its substructure. Both tested membranes can, according to the results, also be used at temperatures as high as 70°C in acidic, neutral and alkaline conditions. However, the use at extreme conditions might cause faster ageing of the membranes compared to ageing in neutral conditions. The thesis proved that both the tested RC membranes are very suitable for pulp and paper mill applications and that the membranes can be utilised in processes operating in challenging conditions. Thus, they could be used in more demanding applications than supposed earlier.

Rapid analysis of multiclass antibiotic residues and some of their metabolites in hospital, urban wastewater and river water by ultra-highperformance liquid chromatography coupled to quadrupole-linear ion trap tandem mass spectrometry

The present work describes the development of a fast and robust analytical method for the determination of 53 antibiotic residues, covering various chemical groups and some of their metabolites, in environmental matrices that are considered important sources of antibiotic pollution, namely hospital and urban wastewaters, as well as in river waters. The method is based on automated off-line solid phase extraction (SPE) followed by ultra-high-performance liquid chromatography coupled to quadrupole linear ion trap tandem mass spectrometry (UHPLC–QqLIT). For unequivocal identification and confirmation, and in order to fulfill EU guidelines, two selected reaction monitoring (SRM) transitions per compound are monitored (the most intense one is used for quantification and the second one for confirmation). Quantification of target antibiotics is performed by the internal standard approach, using one isotopically labeled compound for each chemical group, in order to correct matrix effects. The main advantages of the method are automation and speed-up of sample preparation, by the reduction of extraction volumes for all matrices, the fast separation of a wide spectrum of antibiotics by using ultra-high-performance liquid chromatography, its sensitivity (limits of detection in the low ng/L range) and selectivity (due to the use of tandem mass spectrometry) The inclusion of β-lactam antibiotics (penicillins and cephalosporins), which are compounds difficult to analyze in multi-residue methods due to their instability in water matrices, and some antibiotics metabolites are other important benefits of the method developed. As part of the validation procedure, the method developed was applied to the analysis of antibiotics residues in hospital, urban influent and effluent wastewaters as well as in river water samples

Distinct contributions of Brodmann areas 1 and 2 to body ownership.

Although body ownership-i.e. the feeling that our bodies belong to us-modulates activity within the primary somatosensory cortex (S1), it is still unknown whether this modulation occurs within a somatotopically defined portion of S1. We induced an illusory feeling of ownership for another person's finger by asking participants to hold their palm against another person's palm and to stroke the two joined index fingers with the index and thumb of their other hand. This illusion (numbness illusion) does not occur if the stroking is performed asynchronously or by the other person. We combined this somatosensory paradigm with ultra-high field functional magnetic resonance imaging finger mapping to study whether illusory body ownership modulates activity within different finger-specific areas of S1. The results revealed that the numbness illusion is associated with activity in Brodmann area (BA) 1 within the representation of the finger stroking the other person's finger and in BA 2 contralateral to the stroked finger. These results show that changes in bodily experience modulate the activity within certain subregions of S1, with a different finger-topographical selectivity between the representations of the stroking and of the stroked hand, and reveal that the high degree of somatosensory specialization in S1 extends to bodily self-consciousness.

Trigeminal Neuralgia Secondary to Intracranial Lesions: A Prospective Series of 17 Consecutive Cases

Object: The purpose of the study was to assess the role of Gamma Knife surgery (GKS) in secondary trigeminal neuralgia (TN) caused by space-occupying lesions. Methods: From July 2010 till January 2015, 17 patients had GKS for secondary TN caused by intracranial lesions. The primary outcome was tumor control. The secondary outcomes were the alleviation of pain and the eventual secondary effects. Covariates were the age, duration of symptoms, duration till alleviation etc. Results: The mean age in this series was 63.3 years (range 39-79). The mean follow-up period was 1.85 years (range 0.5-3). Nine (52.9%) were meningiomas, five (29.4%) trigeminal schwannomas, two (11.8%) brain metastases and one (5.9%) arteriovenous malformation (AVM). Eight were located on the right side and nine on the left side. The mean duration of TN was 13.5 months (range 0.5-160). Follow-up was available for 16 patients (94.1%). Pain alleviation appeared after a mean time of 4.6 months (1-11) in 15 patients (88.2%). Five (29.4%) patients completely stopped medication in a mean time of 7 months (range 1-13) and three (17.6%) decreased it at half of the initial doses. No patient developed new hypoesthesia or other cranial nerve complication. The marginal doses for meningiomas and trigeminal schwannomas were 12 Gy (12-14), for metastasis 20 (20-20) and for AVM 24 Gy. The mean target volume was 1.84 cc (range 0.12-8.10). The mean prescription isodose volume was 2.65 cc (0.19-11.90). The mean maximal diameter was 19.9 (range 9-36). The mean number of isocenters was 14.2 (4-27). The mean duration was 76.9 minutes (range 25-172). The mean conformity, selectivity, Paddick and gradient index were: 0.99 (range 0.955-1), 0.701 (range 0.525-0.885), 0.694 (range 0.525-0.885) and 2.904 (range 2.654-3.371). At last follow-up, tumor decreased in 10 (58.8%) patients, was stable in 6 (35.3%) and increased in one (5.9%), the latest at 6 months. Conclusions: Gamma Knife surgery is safe and effective in treating intracranial lesions presenting with secondary TN. The initial pain freedom response was close to 90%, while having no secondary effect. Pain alleviation is achieved even in the absence of a volume variation of the lesions.

Validació del mètode analític per la determinació d'aminoàcids i carbohidrats d'un producte farmacèutic per HPLC

Per poder desenvolupar un producte farmacèutic és necessari establir un mètode d’anàlisis que permeti determinar i quantificar totes aquelles substàncies que conté, ja sigui referent als principis actius; a les impureses i productes de degradació, conservants, antioxidants,... Grans entitats com la ICH remarquen la importància de validar els mètodes analítics ja que és la via per demostrar que aquell producte compleix les garanties de qualitat prèviament establertes. Així doncs, l’objectiu d’aquest Treball Final de Grau és poder desenvolupar i validar dos mètodes analítics per a la determinació d’aminoàcids i carbohidrats respectivament, d’un producte farmacèutic per cromatografia líquida (HPLC). Per tal de poder concloure que aquell mètode és adequat per la determinació per la qual ha estat desenvolupat, és necessari obtenir resultats que compleixin els criteris d’acceptació corresponents als paràmetres que han de ser avaluats en una validació analítica. Aquests paràmetres són: la precisió, la selectivitat, l’exactitud i la linealitat i el rang. Els resultats d’aquest projecte han demostrat que els dos mètodes desenvolupats són adequats per a la determinació de tres dels principis actius (aminoàcid 1, aminoàcid 2 i carbohidrat 1) que conté el producte farmacèutic d’ús veterinari analitzat; i poden ser validats ja que compleixen els criteris d’acceptació dels paràmetres avaluats que proposa la ICH. El mètode per la determinació de carbohidrats no és vàlid per el carbohidrat 2, ja que durant el desenvolupament es va detectar que una bona part d’aquest passava a carbohidrat 1 (desplaçament de l’equilibri ceto-enòlic que hi ha entre el carbohidrat 1 i el carbohidrat 2 a pHs alts). És per aquest motiu, que es pot concloure que aquest mètode no és vàlid i es recomana seguir investigant per a poder desenvolupar un mètode analític adient.

Systematic evaluation of matrix effects in hydrophilic interaction chromatography versus reversed phase liquid chromatography coupled to mass spectrometry.

Reversed phase liquid chromatography (RPLC) coupled to mass spectrometry (MS) is the gold standard technique in bioanalysis. However, hydrophilic interaction chromatography (HILIC) could represent a viable alternative to RPLC for the analysis of polar and/or ionizable compounds, as it often provides higher MS sensitivity and alternative selectivity. Nevertheless, this technique can be also prone to matrix effects (ME). ME are one of the major issues in quantitative LC-MS bioanalysis. To ensure acceptable method performance (i.e., trueness and precision), a careful evaluation and minimization of ME is required. In the present study, the incidence of ME in HILIC-MS/MS and RPLC-MS/MS was compared for plasma and urine samples using two representative sets of 38 pharmaceutical compounds and 40 doping agents, respectively. The optimal generic chromatographic conditions in terms of selectivity with respect to interfering compounds were established in both chromatographic modes by testing three different stationary phases in each mode with different mobile phase pH. A second step involved the assessment of ME in RPLC and HILIC under the best generic conditions, using the post-extraction addition method. Biological samples were prepared using two different sample pre-treatments, i.e., a non-selective sample clean-up procedure (protein precipitation and simple dilution for plasma and urine samples, respectively) and a selective sample preparation, i.e., solid phase extraction for both matrices. The non-selective pretreatments led to significantly less ME in RPLC vs. HILIC conditions regardless of the matrix. On the contrary, HILIC appeared as a valuable alternative to RPLC for plasma and urine samples treated by a selective sample preparation. Indeed, in the case of selective sample preparation, the compounds influenced by ME were different in HILIC and RPLC, and lower and similar ME occurrence was generally observed in RPLC vs. HILIC for urine and plasma samples, respectively. The complementary of both chromatographic modes was also demonstrated, as ME was observed only scarcely for urine and plasma samples when selecting the most appropriate chromatographic mode.

Quantitative performance of a quadrupole-orbitrap-MS in targeted LC-MS determinations of small molecules.

High-resolution mass spectrometry (HRMS) has been associated with qualitative and research analysis and QQQ-MS with quantitative and routine analysis. This view is now challenged and for this reason, we have evaluated the quantitative LC-MS performance of a new high-resolution mass spectrometer (HRMS), a Q-orbitrap-MS, and compared the results obtained with a recent triple-quadrupole MS (QQQ-MS). High-resolution full-scan (HR-FS) and MS/MS acquisitions have been tested with real plasma extracts or pure standards. Limits of detection, dynamic range, mass accuracy and false positive or false negative detections have been determined or investigated with protease inhibitors, tyrosine kinase inhibitors, steroids and metanephrines. Our quantitative results show that today's available HRMS are reliable and sensitive quantitative instruments and comparable to QQQ-MS quantitative performance. Taking into account their versatility, user-friendliness and robustness, we believe that HRMS should be seen more and more as key instruments in quantitative LC-MS analyses. In this scenario, most targeted LC-HRMS analyses should be performed by HR-FS recording virtually "all" ions. In addition to absolute quantifications, HR-FS will allow the relative quantifications of hundreds of metabolites in plasma revealing individual's metabolome and exposome. This phenotyping of known metabolites should promote HRMS in clinical environment. A few other LC-HRMS analyses should be performed in single-ion-monitoring or MS/MS mode when increased sensitivity and/or detection selectivity will be necessary.