A comparison of worker risk of injury while working on fully automated side loaders and other residential collection trucks at a large solid waste collection company

The study aim was to determine whether using automated side loader (ASL) trucks in higher proportions compared to other types of trucks for residential waste collection results in lower injury rates (from all causes). The primary hypothesis was that the risk of injury to workers was lower for those who work with ASL trucks than for workers who work with other types of trucks used in residential waste collection. To test this hypothesis, data were collected from one of the nation’s largest companies in the solid waste management industry. Different local operating units (i.e. facilities) in the company used different types of trucks to varying degrees, which created a special opportunity to examine refuse collection injuries and illnesses and the risk reduction potential of ASL trucks.^ The study design was ecological and analyzed end-of-year data provided by the company for calendar year 2007. During 2007, there were a total of 345 facilities which provided residential services. Each facility represented one observation.^ The dependent variable – injury and illness rate, was defined as a facility’s total case incidence rate (TCIR) recorded in accordance with federal OSHA requirements for the year 2007. The TCIR is the rate of total recordable injury and illness cases per 100 full-time workers. The independent variable, percent of ASL trucks, was calculated by dividing the number of ASL trucks by the total number of residential trucks at each facility.^ Multiple linear regression models were estimated for the impact of the percent of ASL trucks on TCIR per facility. Adjusted analyses included three covariates: median number of hours worked per week for residential workers; median number of months of work experience for residential workers; and median age of residential workers. All analyses were performed with the statistical software, Stata IC (version 11.0).^ The analyses included three approaches to classifying exposure, percent of ASL trucks. The first approach included two levels of exposure: (1) 0% and (2) >0 - <100%. The second approach included three levels of exposure: (1) 0%, (2) ≥ 1 - < 100%, and (3) 100%. The third approach included six levels of exposure to improve detection of a dose-response relationship: (1) 0%, (2) 1 to <25%, (3) 25 to <50%, (4) 50 to <75%, (5) 75 to <100%, and (6) 100%. None of the relationships between injury and illness rate and percent ASL trucks exposure levels was statistically significant (i.e., p<0.05), even after adjustment for all three covariates.^ In summary, the present study shows that there is some risk reduction impact of ASL trucks but not statistically significant. The covariates demonstrated a varied yet more modest impact on the injury and illness rate but again, none of the relationships between injury and illness rate and the covariates were statistically significant (i.e., p<0.05). However, as an ecological study, the present study also has the limitations inherent in such designs and warrants replication in an individual level cohort design. Any stronger conclusions are not suggested.^

The relationship between hospital financial performance and information technology integration strategy selection

In light of the new healthcare regulations, hospitals are increasingly reevaluating their IT integration strategies to meet expanded healthcare information exchange requirements. Nevertheless, hospital executives do not have all the information they need to differentiate between the available strategies and recognize what may better fit their organizational needs. ^ In the interest of providing the desired information, this study explored the relationships between hospital financial performance, integration strategy selection, and strategy change. The integration strategies examined – applied as binary logistic regression dependent variables and in the order from most to least integrated – were Single-Vendor (SV), Best-of-Suite (BoS), and Best-of-Breed (BoB). In addition, the financial measurements adopted as independent variables for the models were two administrative labor efficiency and six industry standard financial ratios designed to provide a broad proxy of hospital financial performance. Furthermore, descriptive statistical analyses were carried out to evaluate recent trends in hospital integration strategy change. Overall six research questions were proposed for this study. ^ The first research question sought to answer if financial performance was related to the selection of integration strategies. The next questions, however, explored whether hospitals were more likely to change strategies or remain the same when there was no external stimulus to change, and if they did change, they would prefer strategies closer to the existing ones. These were followed by a question that inquired if financial performance was also related to strategy change. Nevertheless, rounding up the questions, the last two probed if the new Health Information Technology for Economic and Clinical Health (HITECH) Act had any impact on the frequency and direction of strategy change. ^ The results confirmed that financial performance is related to both IT integration strategy selection and strategy change, while concurred with prior studies that suggested hospital and environmental characteristics are associated factors as well. Specifically this study noted that the most integrated SV strategy is related to increased administrative labor efficiency and the hybrid BoS strategy is associated with improved financial health (based on operating margin and equity financing ratios). On the other hand, no financial indicators were found to be related to the least integrated BoB strategy, except for short-term liquidity (current ratio) when involving strategy change. ^ Ultimately, this study concluded that when making IT integration strategy decisions hospitals closely follow the resource dependence view of minimizing uncertainty. As each integration strategy may favor certain organizational characteristics, hospitals traditionally preferred not to make strategy changes and when they did, they selected strategies that were more closely related to the existing ones. However, as new regulations further heighten revenue uncertainty while require increased information integration, moving forward, as evidence already suggests a growing trend of organizations shifting towards more integrated strategies, hospitals may be more limited in their strategy selection choices.^

Performance of HbA1c for classifying diabetes and diagnostic threshold for diabetes among the Mexican American border community

Objective. In 2009, the International Expert Committee recommended the use of HbA1c test for diagnosis of diabetes. Although it has been recommended for the diagnosis of diabetes, its precise test performance among Mexican Americans is uncertain. A strong “gold standard” would rely on repeated blood glucose measurement on different days, which is the recommended method for diagnosing diabetes in clinical practice. Our objective was to assess test performance of HbA1c in detecting diabetes and pre-diabetes against repeated fasting blood glucose measurement for the Mexican American population living in United States-Mexico border. Moreover, we wanted to find out a specific and precise threshold value of HbA1c for Diabetes Mellitus (DM) and pre-diabetes for this high-risk population which might assist in better diagnosis and better management of patient diabetes. ^ Research design and methods. We used CCHC dataset for our study. In 2004, the Cameron County Hispanic Cohort (CCHC), now numbering 2,574, was established drawn from randomly selected households on the basis of 2000 Census tract data. The CCHC study randomly selected a subset of people (aged 18-64 years) in CCHC cohort households to determine the influence of SES on diabetes and obesity. Among the participants in Cohort-2000, 67.15% are female; all are Hispanic. ^ Individuals were defined as having diabetes mellitus (Fasting plasma glucose [FPG] ≥ 126 mg/dL or pre-diabetes (100 ≤ FPG < 126 mg/dL). HbA1c test performance was evaluated using receiver operator characteristic (ROC) curves. Moreover, change-point models were used to determine HbA1c thresholds compatible with FPG thresholds for diabetes and pre-diabetes. ^ Results. When assessing Fasting Plasma Glucose (FPG) is used to detect diabetes, the sensitivity and specificity of HbA1c≥ 6.5% was 75% and 87% respectively (area under the curve 0.895). Additionally, when assessing FPG to detect pre-diabetes, the sensitivity and specificity of HbA1c≥ 6.0% (ADA recommended threshold) was 18% and 90% respectively. The sensitivity and specificity of HbA1c≥ 5.7% (International Expert Committee recommended threshold) for detecting pre-diabetes was 31% and 78% respectively. ROC analyses suggest HbA1c as a sound predictor of diabetes mellitus (area under the curve 0.895) but a poorer predictor for pre-diabetes (area under the curve 0.632). ^ Conclusions. Our data support the current recommendations for use of HbA1c in the diagnosis of diabetes for the Mexican American population as it has shown reasonable sensitivity, specificity and accuracy against repeated FPG measures. However, use of HbA1c may be premature for detecting pre-diabetes in this specific population because of the poor sensitivity with FPG. It might be the case that HbA1c is differentiating the cases more effectively who are at risk of developing diabetes. Following these pre-diabetic individuals for a longer-term for the detection of incident diabetes may lead to more confirmatory result.^

CHARACTERIZATION OF THE COUNT RATE PERFORMANCE AND EVALUATION OF THE EFFECTS OF HIGH COUNT RATES ON MODERN GAMMA CAMERAS

CHARACTERIZATION OF THE COUNT RATE PERFORMANCE AND EVALUATION OF THE EFFECTS OF HIGH COUNT RATES ON MODERN GAMMA CAMERAS Michael Stephen Silosky, B.S. Supervisory Professor: S. Cheenu Kappadath, Ph.D. Evaluation of count rate performance (CRP) is an integral component of gamma camera quality assurance and measurement of system dead time (τ) is important for quantitative SPECT. The CRP of three modern gamma cameras was characterized using established methods (Decay and Dual Source) under a variety of experimental conditions. For the Decay method, input count rate was plotted against observed count rate and fit to the paralyzable detector model (PDM) to estimate τ (Rates method). A novel expression for observed counts as a function of measurement time interval was derived and the observed counts were fit to this expression to estimate τ (Counts method). Correlation and Bland-Altman analysis were performed to assess agreement in estimates of τ between methods. The dependencies of τ on energy window definition and incident energy spectrum were characterized. The Dual Source method was also used to estimate τ and its agreement with the Decay method under identical conditions and the effects of total activity and the ratio of source activities were investigated. Additionally, the effects of count rate on several performance metrics were evaluated. The CRP curves for each system agreed with the PDM at low count rates but deviated substantially at high count rates. Estimates of τ for the paralyzable portion of the CRP curves using the Rates and Counts methods were highly correlated (r=0.999) but with a small (~6%) difference. No significant difference was observed between the highly correlated estimates of τ using the Decay or Dual Source methods under identical experimental conditions (r=0.996). Estimates of τ increased as a power-law function with decreasing ratio of counts in the photopeak to the total counts and linearly with decreasing spectral effective energy. Dual Source method estimates of τ varied as a quadratic with the ratio of the single source to combined source activities and linearly with total activity used across a large range. Image uniformity, spatial resolution, and energy resolution degraded linearly with count rate and image distorting effects were observed. Guidelines for CRP testing and a possible method for the correction of count rate losses for clinical images have been proposed.

Assessing the relationship between board composition and nonprofit hospital financial performance from a multi-theoretic perspective

This dissertation assesses the relationship between board composition and financial performance for the top 71 major nonprofit hospitals in the United States during the period 2004-2009. The underlying data were collected from copies of IRS Form 990 available at http://www.guidestar.org . The dissertation investigates five factors: board size, board independence (percentage of outsiders), number of MDs, CEO succession and CEO compensation. And it evaluates the results within a multi-theoretic framework drawing on agency theory, resource dependence theory, institutional theory and social network theory. Corporate governance literature suggests that board composition has an important impact on firm financial performance. This dissertation examines whether the same may be true for nonprofit hospitals. The results should help hospital executives make better governance decisions during trying economic times.^

The association between academic achievement and health status among eighth -grade Hispanic students in Houston

This cross-sectional study examines the association between health and academic achievement among Hispanic eighth-grade students in the Houston Independent School District. As part of the district's 3 year Safe Schools/Healthy Students Initiative to enhance comprehensive educational programs, a brief anonymous questionnaire was administered in the classroom to 359 students in two schools during a one-month period in the early part of the 2001 school year. ^ The primary study questions are: Among this sample of Hispanic adolescents, is there a significant association between academic achievement and health status? and in this same population, is there a significant association between health risk behavior and health status? The specific aims of this research are: (1) to describe the association between academic achievement and health status; (2) to describe the association between health risk behaviors and health status; and (3) to describe the relative contribution of health risk behaviors and academic achievement to adolescent health status among this sample of Hispanic adolescents. ^ The survey instrument was a 32-item questionnaire that incorporated: several academic achievement questions measuring usual grades, school-related performance, attendance, student and perceived parental satisfaction with academic achievement, and educational aspirations; two health and quality of life scales measuring adolescent self-reported health; and specific measures of health risk behavior, e.g., frequency of tobacco cigarette smoking, alcohol and other drug use, aggression, and suicidal ideation and behavior that were incorporated from the national Youth Risk Behavior Survey. Questions pertaining to sexual behavior and pregnancy were omitted to comply with school district guidelines. ^ Analysis revealed that strong associations between academic achievement and health status and between health risk behaviors and health status were observed after controlling for the covariates. Eight factors were found to be significantly associated with poor health status: usual grades (low), academic performance (low), academic achievement beliefs (low), classroom and homework performance satisfaction (low), ever drinking alcohol (6 or more times), suicidality (ever thought about, planned for, or sought medical help after attempting suicide), gender (female), and age (15 years and older). (Abstract shortened by UMI.) ^

Optimización de la composición del hueco de fachada en materia de eficiencia energética. Propuesta de indicador como herramienta para el análisis integral del elemento acristalado = Energy performance optimization of window systems. Proposal of an indicator as a tool for an integrated analysis of glazing

La hipótesis de esta tesis es: "La optimización de la ventana considerando simultáneamente aspectos energéticos y aspectos relativos a la calidad ambiental interior (confort higrotérmico, lumínico y acústico) es compatible, siempre que se conozcan y consideren las sinergias existentes entre ellos desde las primeras fases de diseño". En la actualidad se desconocen las implicaciones de muchas de las decisiones tomadas en torno a la ventana; para que su eficiencia en relación a todos los aspectos mencionados pueda hacerse efectiva es necesaria una herramienta que aporte más información de la actualmente disponible en el proceso de diseño, permitiendo así la optimización integral, en función de las circunstancias específicas de cada proyecto. En la fase inicial de esta investigación se realiza un primer acercamiento al tema, a través del estado del arte de la ventana; analizando la normativa existente, los componentes, las prestaciones, los elementos experimentales y la investigación. Se observa que, en ocasiones, altos requisitos de eficiencia energética pueden suponer una disminución de las prestaciones del sistema en relación con la calidad ambiental interior, por lo que surge el interés por integrar al análisis energético aspectos relativos a la calidad ambiental interior, como son las prestaciones lumínicas y acústicas y la renovación de aire. En este punto se detecta la necesidad de realizar un estudio integral que incorpore los distintos aspectos y evaluar las sinergias que se dan entre las distintas prestaciones que cumple la ventana. Además, del análisis de las soluciones innovadoras y experimentales se observa la dificultad de determinar en qué medida dichas soluciones son eficientes, ya que son soluciones complejas, no caracterizadas y que no están incorporadas en las metodologías de cálculo o en las bases de datos de los programas de simulación. Por lo tanto, se plantea una segunda necesidad, generar una metodología experimental para llevar a cabo la caracterización y el análisis de la eficiencia de sistemas innovadores. Para abordar esta doble necesidad se plantea la optimización mediante una evaluación del elemento acristalado que integre la eficiencia energética y la calidad ambiental interior, combinando la investigación teórica y la investigación experimental. En el ámbito teórico, se realizan simulaciones, cálculos y recopilación de información de distintas tipologías de hueco, en relación con cada prestación de forma independiente (acústica, iluminación, ventilación). A pesar de haber partido con un enfoque integrador, resulta difícil esa integración detectándose una carencia de herramientas disponible. En el ámbito experimental se desarrolla una metodología para la evaluación del rendimiento y de aspectos ambientales de aplicación a elementos innovadores de difícil valoración mediante la metodología teórica. Esta evaluación consiste en el análisis comparativo experimental entre el elemento innovador y un elemento estándar; para llevar a cabo este análisis se han diseñado dos espacios iguales, que denominamos módulos de experimentación, en los que se han incorporado los dos sistemas; estos espacios se han monitorizado, obteniéndose datos de consumo, temperatura, iluminancia y humedad relativa. Se ha realizado una medición durante un periodo de nueve meses y se han analizado y comparado los resultados, obteniendo así el comportamiento real del sistema. Tras el análisis teórico y el experimental, y como consecuencia de esa necesidad de integrar el conocimiento existente se propone una herramienta de evaluación integral del elemento acristalado. El desarrollo de esta herramienta se realiza en base al procedimiento de diagnóstico de calidad ambiental interior (CAI) de acuerdo con la norma UNE 171330 “Calidad ambiental en interiores”, incorporando el factor de eficiencia energética. De la primera parte del proceso, la parte teórica y el estado del arte, se obtendrán los parámetros que son determinantes y los valores de referencia de dichos parámetros. En base a los parámetros relevantes obtenidos se da forma a la herramienta, que consiste en un indicador de producto para ventanas que integra todos los factores analizados y que se desarrolla según la Norma UNE 21929 “Sostenibilidad en construcción de edificios. Indicadores de sostenibilidad”. ABSTRACT The hypothesis of this thesis is: "The optimization of windows considering energy and indoor environmental quality issues simultaneously (hydrothermal comfort, lighting comfort, and acoustic comfort) is compatible, provided that the synergies between these issues are known and considered from the early stages of design ". The implications of many of the decisions made on this item are currently unclear. So that savings can be made, an effective tool is needed to provide more information during the design process than the currently available, thus enabling optimization of the system according to the specific circumstances of each project. The initial phase deals with the study from an energy efficiency point of view, performing a qualitative and quantitative analysis of commercial, innovative and experimental windows. It is observed that sometimes, high-energy efficiency requirements may mean a reduction in the system's performance in relation to user comfort and health, that's why there is an interest in performing an integrated analysis of indoor environment aspects and energy efficiency. At this point a need for a comprehensive study incorporating the different aspects is detected, to evaluate the synergies that exist between the various benefits that meet the window. Moreover, from the analysis of experimental and innovative windows, a difficulty in establishing to what extent these solutions are efficient is observed; therefore, there is a need to generate a methodology for performing the analysis of the efficiency of the systems. Therefore, a second need arises, to generate an experimental methodology to perform characterization and analysis of the efficiency of innovative systems. To address this dual need, the optimization of windows by an integrated evaluation arises, considering energy efficiency and indoor environmental quality, combining theoretical and experimental research. In the theoretical field, simulations and calculations are performed; also information about the different aspects of indoor environment (acoustics, lighting, ventilation) is gathered independently. Despite having started with an integrative approach, this integration is difficult detecting lack available tools. In the experimental field, a methodology for evaluating energy efficiency and indoor environment quality is developed, to be implemented in innovative elements which are difficult to evaluate using a theoretical methodology This evaluation is an experimental comparative analysis between an innovative element and a standard element. To carry out this analysis, two equal spaces, called experimental cells, have been designed. These cells have been monitored, obtaining consumption, temperature, luminance and relative humidity data. Measurement has been performed during nine months and results have been analyzed and compared, obtaining results of actual system behavior. To advance this optimization, windows have been studied from the point of view of energy performance and performance in relation to user comfort and health: thermal comfort, acoustic comfort, lighting comfort and air quality; proposing the development of a methodology for an integrated analysis including energy efficiency and indoor environment quality. After theoretical and experimental analysis and as a result of the need to integrate existing knowledge, a comprehensive evaluation procedure for windows is proposed. This evaluation procedure is developed according to the UNE 171330 "Indoor Environmental Quality", also incorporating energy efficiency and cost as factors to evaluate. From the first part of the research process, outstanding parameters are chosen and reference values of these parameters are set. Finally, based on the parameters obtained, an indicator is proposed as windows product indicator. The indicator integrates all factors analyzed and is developed according to ISO 21929-1:2011"Sustainability in building construction. Sustainability indicators. Part 1: Framework for the development of indicators and a core set of indicators for buildings".

Effect of type of dietary carbohydrates on digestion, intestinal barrier and growth performance in 25-d weaned rabbits

Los objetivos globales de esta tesis han sido estudiar el efecto que los carbohidratos de la dieta ejercen sobre los rendimientos productivos, la barrera intestinal, y la digestión de animales destetados a 25 días de edad. Además se ha estudiado cuál es el mejor periodo para determinar la digestibilidad fecal tras el destete a esta edad. En el primer experimento se estudió el efecto de la fibra neutro detergente soluble (FNDS) sobre la barrera intestinal, digestión, microbiota intestinal y rendimientos productivos de gazapos en gazapos en la fase post-destete. Se diseñaron tres piensos isonutritivos en los que la única fuente de variación fueron los niveles de fibra soluble. A partir de una dieta control (AH) con 103 g/kg de materia seca de FNDS y alfalfa como fuente principal de fibra, se sustituyó la mitad de esta alfalfa por una mezcla de pulpa de remolacha y pulpa de manzana (75:25) en el pienso B-AP y por una mezcla de cascarilla y concentrado de proteína de soja (88:12) en el pienso OH, obteniéndose 131 y 79 g/kg de FNDS sobre materia seca, respectivamente. Los conejos se destetaron a 25 días y fueron alimentados con los piensos experimentales hasta los 35 días de edad, momento en el que se sacrificaron para la determinación de la digestibilidad ileal aparente (DIA) de la materia seca (MS), proteína bruta (PB) y almidón, la morfología de la mucosa, y actividad enzimática en el yeyuno, el tejido linfoide asociado a la mucosa, así como la microbiota intestinal. Para la determinación de la morfología de la mucosa se utilizaron adicionalmente 19 animales lactantes de 35 días de edad. Para el estudio de la tasa de mortalidad, se utilizaron 118 animales más por tratamiento que recibieron los piensos experimentales durante las dos semanas post-destete y posteriormente un pienso comercial hasta los 60 días de edad. Los animales recibieron durante todo el experimento medicación en el agua de bebida (100 ppm de apramicina sulfato y 120 ppm de tilosina tartrato). El nivel de fibra soluble mejoró los parámetros que se utilizaron para la caracterización del estado de la barrera intestinal. Los conejos alimentados con el mayor nivel de FNDS en el pienso presentaron una mayor longitud de los villi (P=0.001), un mayor ratio longitud villi/profundidad de las criptas (8.14; P=0.001), una mayor actividad disacaridásica (8671 μmol de glucosa/g de proteína; P=0.019), así como una mayor digestibilidad ileal (96.8%; P=0.002), observándose una reducción en el flujo ileal de almidón a medida que se incrementó el nivel de fibra soluble en el pienso (1,2 vs 0,5 g/d; P=0.001). Los animales lactantes a 35 días de edad presentaron un ratio longitud de villi/profundidad de las criptas menor que el observado en aquéllos alimentados con el pienso B-AP (6.70), pero superior al de los piensos AH y OH. Niveles inferiores de NDFS tendieron (P=0.074) a incrementar la respuesta inmune de tipo celular (linfocitos CD8+). El pienso también afectó a la producción de IL2 (CD25+; P=0.029; CD5+CD25+; P=0.057), pero sin llegar a establecerse una clara relación con el nivel de fibra soluble. La diversidad de la microbiota intestinal no se vio afectada por el pienso (P ≥ 0.38). Los animales alimentados con las piensos B-AP y AH presentaron una reducción en la frecuencia de detección de Clostridium perfringens tanto en íleon (P=0.062) como en ciego (4.3 vs. 17.6%, P =0.047), comparado con el pienso OH. Además la tasa de mortalidad (118 gazapos/pienso) disminuyó de 14.4% en el pienso OH a 5.1% en el pienso B-AP. Entre los 32 y los 35 días de edad se determinó la digestibilidad fecal aparente (14/pienso) de la materia seca (MS), energía bruta (EB), proteína bruta (PB), fibra neutro detergente (FND), fibra ácido detergente (FAD) y almidón. Este grupo, junto con otros nueve animales por tratamiento se utilizaron para determinar el peso del estómago y el ciego, la concentración cecal de ácidos grasos volátiles (AGV) y amoniaco (NH3), así como las tasas de similitud de la microbiota intestinal. Además se estudiaron los rendimientos productivos (35 animales/tratamiento) de los gazapos durante todo el período de cebo, consumiendo los piensos experimentales desde el destete hasta los 35 días y posteriormente un pienso comercial hasta los 60 días de edad. Niveles crecientes de FNDS mejoraron la digestibilidad fecal de la materia seca (MS) y energía (P<0.001). La inclusión FNDS aumentó de manera lineal el peso del contenido cecal (P=0.001) y el peso del aparato digestivo completo (P=0.008), y en los días previos al sacrificio disminuyó de manera lineal el consumo medio diario (P=0.040). Se observó además, una disminución lineal (P≤0.041) del pH del estómago. No se encontró relación entre el pH, la concentración y proporciones molares de AGV y el nivel de FNDS. El pienso pareció tener un efecto, incluso superior al de la madre, sobre la tasa de similitud de la microbiota, y los efectos fueron mayores a nivel cecal que ileal. La eficacia alimenticia aumentó de manera lineal en un 12% entre piensos extremos tras el destete (25- 39d) y en un 3% en el período global de cebo con niveles mayores de NDFS. El consumo medio diario durante la fase post-destete y durante todo el período de cebo, tendió a aumen tar (P≤0.079) con niveles mayores de FNDS, sin embargo no se apreció efecto sobre la ganancia media diaria (P≥0.15). En conclusión, el incremento del nivel de fibra soluble en el pienso parece resultar beneficioso para la salud del animal ya que mejora la integridad de la mucosa, y reduce la frecuencia de detección de potenciales patógenos como C. perfringens y Campylobacter spp. Conforme a estos resultados, debería tenerse en cuenta el contenido en fibra soluble en la formulación de piensos de conejos en la fase post-destete. El objetivo del segundo experimento fue determinar el efecto de la fuente de almidón sobre la digestión, la microbiota intestinal y los rendimientos productivos en conejos destetados con 25 días de edad. Se formularon tres piensos isonutritivos en los que se modificaron las principales fuentes de almidón: trigo crudo, trigo cocido y una combinación de trigo y arroz cocido. Dos grupos de 99 y 193 animales se destetaron con 25 días de edad. El primero de ellos se utilizó para la determinación de los parámetros productivos conforme al mismo protocolo seguido en el experimento anterior. El segundo de los grupos se utilizó para la determinación de la digestibilidad fecal de 32 a 35 d, la digestibilidad ileal aparente (DIA) a 35 d, la morfología de la mucosa intestinal, los parámetros de fermentación cecal; así como, la caracterización de la microbiota intestinal. Se utilizaron además dos grupos adicionales de animales 384 (medicados) y 177 (no medicados) para estudiar el efecto de la suplementación con antibióticos en el agua de bebida sobre la mortalidad. El procesado térmico del trigo mejoró ligeramente la digestibilidad ileal del almidón (P=0.020) pero no modificó el flujo final de almidón que alcanzó el ciego, observándose una mayor frecuencia de detección de Campylobacter spp. y Ruminococcus spp. en ciego (P≤0.023), pero sin cambios a nivel ileal. El procesado térmico del trigo no afectó tampoco a los parámetros productivos, la mortalidad, la digestibilidad ileal y fecal o la morfología de la mucosa. La sustitución parcial del trigo cocido por arroz cocido, penalizó la digestibilidad ileal del almidón (P=0.020) e incrementó el flujo ileal de este nutriente al ciego (P=0.007). Sin embargo no afectó a la mortalidad, pese a que se detectaron cambios en la microbiota tanto a nivel ileal como cecal, disminuyendo la frecuencia de detección de Campylobacter spp. (en íleon y ciego), Helicobacter spp. (en íleon) y Ruminococcus spp (en ciego) e incrementando Bacteroides spp. (en ciego) (P≤0.046). El empleo de arroz cocido en las piensos post-destete no tuvieron efectos sobre los parámetros productivos, la mortalidad, la digestibilidad ileal y fecal a excepción del almidón, o la morfología de la mucosa. La suplementación con antibiótico redujo la fre cuencia de detección de la mayoría de las bacterias estudiadas (P≤0.048), sobre todo para Campylobacter spp., Clostridium perfringens y Propionibacterium spp. (P≤0.048), observándose un efecto mayor a nivel ileal que cecal, lo que se asoció a la bajada significativa (P<0.001) de la mortalidad. En conclusión, los resultados de este experimento indican que la fuente de almidón afecta a la microbiota intestinal pero no influiye sobre la salud del animal. En relación al procesado, el uso de trigo cocido junto con arroz cocido no mejora los resultados obtenidos con trigo duro, si bienserían necesarios más experimentos que confirmaran este punto. El último de los experimentos se centró en un aspecto metodológico. Dado que, los conejos destetados presentan un patrón digestivo diferente al de un animal adulto resultado de su inmadurez digestiva, el objetivo buscado era tratar de determinar el mejor procedimiento para la determinación de la digestibilidad fecal en los gazapos en la fase post-destete. Para tal fin se utilizaron 15 animales/tratamiento de tres camadas diferentes que se destetaron con 25 días, suministrándoles un pienso comercial de crecimiento-cebo. Se registró el consumo medio diario y la excreción diaria de heces desde el día 25 hasta el día 40 de edad para la determinación de la digestibilidad de la MS. La camada afectó al consumo medio diario y la excreción de heces (P=0.013 y 0.014, respectivamente), observándose una tendencia (P=0.061) en la digestibilidad. La edad afectó (P<0.001) a todos estos factores, incrementándose de manera más evidente la excreción que la ingestión de materia seca en la primera semana de vida, para aumentar de forma paralela a partir de la segunda. La correlación entre el consumo medio diario fue mayor con la excreción de heces del mismo día que con la del día siguiente, por lo que se utilizó el primero para la determinación de la digestibilidad de la MS (MSd). La MSd disminuyó de manera lineal hasta los 32 días de edad (2.17±0.25 unidades porcentuales por día), mientras que permaneció constante desde los 32 a los 40 días (69.4±0.47%). Por otro lado, la desviación estándar de la MSd se redujo cuando se incrementó el período de recogida de 2 a 6 días en un 54%. Conforme a los resultados obtenidos, se puede concluir que no es aconsejable comenzar las pruebas de digestibilidad antes de los 32 días de edad y que el número de animales necesario para detectar diferencias significativas entre tratamientos dependerá del período de recogida de heces. ABSTRACT The global aim of this thesis has been to study the effect of dietary carbohydrates on growth, performance, digestion and intestinal barrier in 25-d weaned rabbits. In addition there has also been studied which is the best period to determine the fecal digestibility after weaning. The first experiment focused on the effect of Neutral Detergent Soluble Fibre (NDSF) on gut barrier function, digestion, intestinal microbiota and growth performance n rabbits in the post-weaning period. Three isonutritive diets which only varied in the levels of soluble fiber were formulated such as it described as follows: a control diet (AH) containing 103 g of neutral detergent soluble fiber, including alfalfa as main source of fiber, was replaced by a mixture of beet and apple pulp (75-25) in the B-AP diet and, by a mix of oat hulls and soybean protein concentrate (88:12) in the OH diet, resulting 131 and 79 g of NDFS/kg of dry matter, respectively. Rabbits, weaned at 25 days of age, were fed the experimental diets up to 35 days of age, moment in which they were slaughtered for apparent ileal digestibility (AID) of dry matter (DM), crude protein (CP) and starch, mucosa morphology, sucrose activity, characterization of lamina propria lymphocytes and intestinal microbiota. To assess mucosal morphology, 19 suckling 35-d-old rabbits were also used. For mortality study, besides these animals, 118 additional rabbits per treatment were fed the experimental diets for two weeks period and thereafter received a commercial diet until 60 days of age. Rabbits were water medicated during the whole experimental period (100 ppm de apramicine sulphate and 120 ppm of tylosine tartrate). Level of soluble fiber improved all the parameters used for the characterization of the intestinal barrier condition. Villous height of the jejunal mucosa increased with dietary soluble fiber (P=0.001). Villous height of jejunal mucosa increased with dietary soluble fiber (P = 0.001). Rabbits fed the highest level of soluble fiber (BA-P diet) showed the highest villous height/crypth depth ratio (8.14; P = 0.001), sucrase specific activity (8671 μmol glucose/ g protein; P = 0.019), and the greatest ileal starch digestibility (96.8%; P = 0.002). The opposite effects were observed in rabbits fed decreased levels of soluble fiber (AH and OH diets; 4.70, 5,848 μmol of glucose/g of protein, as average, respectively). The lowest ileal starch digestibility was detected for animal fed OH diet (93.2%). Suckling rabbits of the same age showed a lower villous height/crypt depth ratio (6.70) compared with the B-AP diet group, but this ration was higher that the AH or OH diet groups. Lower levels of soluble fiber tended (P = 0.074) to increase the cellular immune response (CD8+ lymphocytes). Diet affected IL-2 production (CD25+, P = 0.029; CD5+CD25+, P = 0.057), with no clear relationship between soluble fiber and IL-2. The intestinal microbiota biodiversity was not affected by diets (P ≥ 0.38). Animals fed B-AP and AH diets had a reduced cecal frequency of detection compatible with Campylobacter spp. (20.3 vs. 37.8, P = 0.074), and Clostridium perfringens (4.3 vs. 17.6%, P = 0.047), compared with the OH diet group. Moreover, the mortality rates decreased from 14.4 (OH diet) to 5.1% (B-AP diet) with the increased presence of soluble fiber in the diet. Between 32 and 35 days of age, faecal apparent digestibility of dry matter (DM), gross energy (GE), crude protein (CP), neutral detergent fiber (NDF), acid detergent fiber (ADF) and starch was determined (14/diet). This group, plus another nine rabbits/diet were used to determine weight of stomach and caecum and their contents, cecal fermentation traits and similarity rate (SR) of intestinal microbiota. Besides, growth performance parameters (35 rabbits/diet) were studied during the whole fattening period, in animals consuming the experimental feed after the weaning up to 35 days of age and later on a commercial diet up animals reached 60 days of age. Increasing levels of Neutral Detergent Soluble Fiber improved faecal dry matter and energy digestibility (P<0.001). NDSF inclusion improved linearly weight of the caecal content (P=0.001) and the total gastrointestinal tract (P=0.008), and in the previous days to slaughter a linear decrease of daily feed intake in diet with highest level of soluble fiber was also observed. Stomach pH decreased linearly with increasing levels of NDFS (P≤0.041). No relation between NDSF level on pH, concentration and molar proportion of VFA was found. Treatments appeared to influence the similarity rate of microbiota, even higher to mother effect. These effects were higher in ileum than in caecum. A linear positive effect of feed efficiency was observed, which increased around 12% in the two weeks post-weaning (25-39d) and 3% in the whole fattening period between extreme diets with highest levels of soluble fiber. Average daily feed intake during the two weeks after weaning and in the whole fattening period, tended (P≤0.079) to increase with highest levels of NDSF; although there were no effect on daily weight gain (≥0.15). In conclusion, an increase of soluble fiber in the feed seems to be beneficial for animal health, due to improve mucose integrity and reduce detection frequency of those poten tial pathogens like C. perfringens and Campylobacter spp. According to these results, level of soluble fiber should be taking care in feed rabbit formulation in the post-weaning period. The objective of the second experiment was to determine the effect of source of starch on digestion, intestinal microbiota and growth performance in twenty-five-day old weaned rabbits. To accomplish with this aim three iso-nutritive diets were formulated with different source of starch: raw wheat, boiled wheat and a combination of boiled wheat and boiled rice. Two groups of 99 and 193 rabbits were weaned at 25 days of age. The first group was used for growth performance determination following the same protocol than in previous experiment. The second group was used to determine faecal digestibility from 32 to 35 d, apparent ileal digestibility (AID) at 35 d, jejunal mucosa morphology, caecal fermentation traits and characterization of intestinal microbiota. For mortality, two additional groups of 384 (medicated) and 177 (not medicated) were used in order to study the effect of antibiotic water supply supplementation. Heat processing of starch slightly improved ileal digestibility of starch (P=0.020) but did not modify the flow of starch to the caecum. An increase in frequency of detection of Campylobacter spp. y Ruminococcus spp. was observed in the caecum (P≤0.023), with no changes at ileal level. Heat processing of wheat did not modify growth performance, mortality, ileal or faecal digestibility and mucosa morphology. Partial substitution of boiled wheat for boiled rice in the diet impaired ileal starch digestibility (P=0.020) and increased the ileal flow of this nutrient to the caecum (P=0.007). However, it did not affect mortality rate, although changes in the ileal and caecal intestinal microbiota were detected, decreasing the frequency of detection of Campylobacter spp. (both ileum and caecum), Helicobacter spp. (at ileum) and Ruminococcus spp (at caecum) and increasing the Bacteroides spp. (at caecum) (P≤0.046). The effect of boiled rice supplementation did not alter growth performance, mortality, ileal or faecal digestibility of other nutrients than starch, and mucosa morphology. Medication of rabbits reduced the ileal frequency of detection of most bacteria studied (P≤0.048), especially for Campylobacter spp., Clostridium perfringens y Propionibacterium spp. (P≤0.048), resulting the effect higher at ileal than caecal level and relating it with a strong reduction of mortality rate (P<0.001). In conclusion, the results of this experiment make think that the source of starch affects the intestinal microbiota but they do not seem to influence animal health. In relation to the effect of heat processed the use of cooked wheat or cooked rice it does not seem to im prove the results obtained with hard wheat, but there would be necessary more experiments that were confirming this point. The last experiment focused on a methodological aspect. Considering that, weaned rabbits have a different digestive pattern than older animals due to their digestive immaturity; the fixed objective was to determine the best procedure for faecal digestibility determination in young rabbits in the post-weaning period. Fifteen rabbits from 5 different litters were weaned at 25 days of age and fed with a commercial feed. Feed intake and faeces excretion were recorded daily from 25 to 40 days of age for dry matter digestibility (DMd) determination. Litter affected daily DM intake and excretion (P=0.013 y 0.014, respectively) and tended to affect DMd (P=0.061). Age affected all these factors (P<0.001), but ingestion increased slowly than dry matter excretion during the first week buth they evolved similarly in the second week. The correlation between daily feed intakes was higher with the faeces excretion of the day than with faeces excretion of the next day, and the first values were used to determine daily DMd. The DMd decreased linearly from weaning to 32 d of age (2.17±0.25 percentage units per day), whereas from 32 to 40 d remained constant (69.4±0.47%). On the other hand, average standard deviation of DMd decreased by 54% when the length of collection period increased from 2 to 6d. Consequently to the obtained results, it could be concluded that it would not be advisable to start digestibility trials before the 32 days of age and that the number of animals required to detect a significant difference among means would depend on the collection period.

Descriptive study of production factors affecting performance traits in growing-finishing pgis in Spain.

The objective of this study was to build up a data set including productive performance and production factors data of growing-finishing (GF) pigs in Spain in order to perform a representative and reliable description of the traits of Spanish growing-finishing pig industry. Data from 764 batches from 452 farms belonging to nine companies (1,157,212 pigs) were collected between 2008 and 2010 through a survey including five parts: general, facilities, feeding, health status and performance. Most studied farms had only GF pigs on their facilities (94.7%), produced ‘industrial’ pigs (86.7%), had entire male and female (59.5%) and Pietrain-sired pigs (70.0%), housed between 13-20 pigs per pen (87.2%), had  50% of slatted floor (70%), single-space dry feeder (54.0%), nipple drinker (88.7%) and automatic ventilation systems (71.2%). A 75.0% of the farms used three feeding phases using mainly pelleted diets (91.0%), 61.3% performed three or more antibiotic treatments and 36.5% obtained water from the public supply. Continuous variables studied had the following average values: number of pigs placed per batch, 1,515 pigs; initial and final body weight, 19.0 and 108 kg; length of GF period, 136 days; culling rate, 1.4%; barn occupation, 99.7%; feed intake per pig and fattening cycle, 244 kg; daily gain, 0.657 kg; feed conversion ratio, 2.77 kg kg-1 and mortality rate, 4.3%. Data reflecting the practical situation of the Spanish growing and finishing pig production and it may contribute to develop new strategies in order to improve the productive and economic efficiency of GF pig units.

Feasibility of a wireless health monitoring system for prevention and health assessment of elderly people

The work presented in this paper comprises the methodology and results of a pilot study on the feasibility of a wireless health monitoring system designed under main EU challenges for the promotion of healthy and active ageing. The system is focused on health assessment, prevention and lifestyle promotion of elderly people. Over a hundred participants including elderly users and caregivers tested the system in four pilot sites across Europe. Tests covered several scenarios in senior centers and real home environments, including performance and usability assessment. Results indicated strong satisfactoriness on usability, usefulness and user friendliness, and the acceptable level of reliability obtained supports future investigation on the same direction for further improvement and transfer of conclusions to the real world in the healthcare delivery.

Effect of late weaning and use of alternative cages on performance of does, suckling and fattening rabbits under extensive reproductive management

The effects of the combined use of long lactation periods (46 days) with alternative cages on the reproductive and growth performance of 104 rabbit does and their litters during five consecutive reproductive cycles were studied. Half of does were housed in conventional polyvalent cages (39 cm×100 cm×30 cm) and the other half in alternative polyvalent cages (39 cm×100 cm×60 cm), with a raised platform. Half of the rabbit does in each type of cage were weaned at 32 and the other half at 46 days after parturition. Longer lactation negatively affected the body weight (P<0.001), fat and energy content (P<0.05) of rabbit does at the end of the lactation period, but this effect decreased with the number of parturitions. Fertility, prolificacy and doe mortality were not affected by lactation length. Late weaning led to higher litter size (by 8.9%) and litter weight (by 11.3%) at the end of growing period (P<0.001) and lower feed conversion ratio per cage during the experimental period (13.5%) than weaning at 32 day (P<0.001). These results were paralleled by lower mortality (12.6 vs. 17.6%; P<0.01) of young rabbits weaned later during the overall experimental period. Differences in performance as a result of different weaning ages were only observed during cycles with worst health status (third and fifth cycles) in which late weaning decreased mortality. Type of cage did not affect doe body weight and body condition, mortality, fertility, prolificacy and litter size during the five reproductive cycles. Nevertheless, at day 21 litter weight and feed conversion ratio between 3 and 21 day were 4.2% higher (P<0.01) and 5.0% lower (P<0.05), respectively, in animals housed in alternative rather than in conventional cages. Alternative cages also led to heavier litters at 59 days (P<0.01). It was concluded that the combined use of longer lactations and cages with higher available surface with a raised platform could be alternatives to improve animal welfare in farmed rabbit.

Effect of late weaning and use of alternative cages on performance of does, suckling and fattening rabbits under extensive reproductive management

The effects of the combined use of long lactation periods (46 days) with alternative cages on the reproductive and growth performance of 104 rabbit does and their litters during five consecutive reproductive cycles were studied. Half of does were housed in conven- tional polyvalent cages (39 cm x 100 cm x 30 cm) and the other half in alternative polyvalent cages (39 cm x 100 cm x 60 cm), with a raised platform. Half of the rabbit does in each type of cage were weaned at 32 and the other half at 46 days after parturition. Longer lactation negatively affected the body weight ( P o 0.001), fat and energy content ( P o 0.05) of rabbit does at the end of the lactation period, but this effect decreased with the number of parturitions. Fertility, prolificacy and doe mortality were not affected by lactation length. Late weaning led to higher litter size (by 8.9%) and litter weight (by 11.3%) at the end of growing period ( P o 0.001) and lower feed conversion ratio per cage during the experimental period (13.5%) than weaning at 32 day ( P o 0.001). These results were paralleled by lower mortality (12.6 vs. 17.6%; P o 0.01) of young rabbits weaned later during the overall experimental period. Differences in performance as a result of different weaning ages were only observed during cycles with worst health status (third and fifth cycles) in which late weaning decreased mortality. Type of cage did not affect doe body weight and body condition, mortality, fertility, prolificacy and litter size during the five reproductive cycles. Nevertheless, at day 21 litter weight and feed conversion ratio between 3 and 21 day were 4.2% higher ( P o 0.01) and 5.0% lower ( P o 0.05), respectively, in animals housed in alternative rather than in conventional cages. Alternative cages also led to heavier litters at 59 days ( P o 0.01). It was concluded that the combined use of longer lactations and cages with higher available surface with a raised platform could be alternatives to improve animal welfare in farmed rabbit.

Application of PZT and FBG impedance sensors for structural health monitoring of reinforced concrete beams strengthened with FRP composite materials

Esta Tesis tiene como objetivo principal el desarrollo de métodos de identificación del daño que sean robustos y fiables, enfocados a sistemas estructurales experimentales, fundamentalmente a las estructuras de hormigón armado reforzadas externamente con bandas fibras de polímeros reforzados (FRP). El modo de fallo de este tipo de sistema estructural es crítico, pues generalmente es debido a un despegue repentino y frágil de la banda del refuerzo FRP originado en grietas intermedias causadas por la flexión. La detección de este despegue en su fase inicial es fundamental para prevenir fallos futuros, que pueden ser catastróficos. Inicialmente, se lleva a cabo una revisión del método de la Impedancia Electro-Mecánica (EMI), de cara a exponer sus capacidades para la detección de daño. Una vez la tecnología apropiada es seleccionada, lo que incluye un analizador de impedancias así como novedosos sensores PZT para monitorización inteligente, se ha diseñado un procedimiento automático basado en los registros de impedancias de distintas estructuras de laboratorio. Basándonos en el hecho de que las mediciones de impedancias son posibles gracias a una colocación adecuada de una red de sensores PZT, la estimación de la presencia de daño se realiza analizando los resultados de distintos indicadores de daño obtenidos de la literatura. Para que este proceso sea automático y que no sean necesarios conocimientos previos sobre el método EMI para realizar un experimento, se ha diseñado e implementado un Interfaz Gráfico de Usuario, transformando la medición de impedancias en un proceso fácil e intuitivo. Se evalúa entonces el daño a través de los correspondientes índices de daño, intentando estimar no sólo su severidad, sino también su localización aproximada. El desarrollo de estos experimentos en cualquier estructura genera grandes cantidades de datos que han de ser procesados, y algunas veces los índices de daño no son suficientes para una evaluación completa de la integridad de una estructura. En la mayoría de los casos se pueden encontrar patrones de daño en los datos, pero no se tiene información a priori del estado de la estructura. En este punto, se ha hecho una importante investigación en técnicas de reconocimiento de patrones particularmente en aprendizaje no supervisado, encontrando aplicaciones interesantes en el campo de la medicina. De ahí surge una idea creativa e innovadora: detectar y seguir la evolución del daño en distintas estructuras como si se tratase de un cáncer propagándose por el cuerpo humano. En ese sentido, las lecturas de impedancias se emplean como información intrínseca de la salud de la propia estructura, de forma que se pueden aplicar las mismas técnicas que las empleadas en la investigación del cáncer. En este caso, se ha aplicado un algoritmo de clasificación jerárquica dado que ilustra además la clasificación de los datos de forma gráfica, incluyendo información cualitativa y cuantitativa sobre el daño. Se ha investigado la efectividad de este procedimiento a través de tres estructuras de laboratorio, como son una viga de aluminio, una unión atornillada de aluminio y un bloque de hormigón reforzado con FRP. La primera ayuda a mostrar la efectividad del método en sencillos escenarios de daño simple y múltiple, de forma que las conclusiones extraídas se aplican sobre los otros dos, diseñados para simular condiciones de despegue en distintas estructuras. Demostrada la efectividad del método de clasificación jerárquica de lecturas de impedancias, se aplica el procedimiento sobre las estructuras de hormigón armado reforzadas con bandas de FRP objeto de esta tesis, detectando y clasificando cada estado de daño. Finalmente, y como alternativa al anterior procedimiento, se propone un método para la monitorización continua de la interfase FRP-Hormigón, a través de una red de sensores FBG permanentemente instalados en dicha interfase. De esta forma, se obtienen medidas de deformación de la interfase en condiciones de carga continua, para ser implementadas en un modelo de optimización multiobjetivo, cuya solución se haya por medio de una expansión multiobjetivo del método Particle Swarm Optimization (PSO). La fiabilidad de este último método de detección se investiga a través de sendos ejemplos tanto numéricos como experimentales. ABSTRACT This thesis aims to develop robust and reliable damage identification methods focused on experimental structural systems, in particular Reinforced Concrete (RC) structures externally strengthened with Fiber Reinforced Polymers (FRP) strips. The failure mode of this type of structural system is critical, since it is usually due to sudden and brittle debonding of the FRP reinforcement originating from intermediate flexural cracks. Detection of the debonding in its initial stage is essential thus to prevent future failure, which might be catastrophic. Initially, a revision of the Electro-Mechanical Impedance (EMI) method is carried out, in order to expose its capabilities for local damage detection. Once the appropriate technology is selected, which includes impedance analyzer as well as novel PZT sensors for smart monitoring, an automated procedure has been design based on the impedance signatures of several lab-scale structures. On the basis that capturing impedance measurements is possible thanks to an adequately deployed PZT sensor network, the estimation of damage presence is done by analyzing the results of different damage indices obtained from the literature. In order to make this process automatic so that it is not necessary a priori knowledge of the EMI method to carry out an experimental test, a Graphical User Interface has been designed, turning the impedance measurements into an easy and intuitive procedure. Damage is then assessed through the analysis of the corresponding damage indices, trying to estimate not only the damage severity, but also its approximate location. The development of these tests on any kind of structure generates large amounts of data to be processed, and sometimes the information provided by damage indices is not enough to achieve a complete analysis of the structural health condition. In most of the cases, some damage patterns can be found in the data, but none a priori knowledge of the health condition is given for any structure. At this point, an important research on pattern recognition techniques has been carried out, particularly on unsupervised learning techniques, finding interesting applications in the medicine field. From this investigation, a creative and innovative idea arose: to detect and track the evolution of damage in different structures, as if it were a cancer propagating through a human body. In that sense, the impedance signatures are used to give intrinsic information of the health condition of the structure, so that the same clustering algorithms applied in the cancer research can be applied to the problem addressed in this dissertation. Hierarchical clustering is then applied since it also provides a graphical display of the clustered data, including quantitative and qualitative information about damage. The performance of this approach is firstly investigated using three lab-scale structures, such as a simple aluminium beam, a bolt-jointed aluminium beam and an FRP-strengthened concrete specimen. The first one shows the performance of the method on simple single and multiple damage scenarios, so that the first conclusions can be extracted and applied to the other two experimental tests, which are designed to simulate a debonding condition on different structures. Once the performance of the impedance-based hierarchical clustering method is proven to be successful, it is then applied to the structural system studied in this dissertation, the RC structures externally strengthened with FRP strips, where the debonding failure in the interface between the FRP and the concrete is successfully detected and classified, proving thus the feasibility of this method. Finally, as an alternative to the previous approach, a continuous monitoring procedure of the FRP-Concrete interface is proposed, based on an FBGsensors Network permanently deployed within that interface. In this way, strain measurements can be obtained under controlled loading conditions, and then they are used in order to implement a multi-objective model updating method solved by a multi-objective expansion of the Particle Swarm Optimization (PSO) method. The feasibility of this last proposal is investigated and successfully proven on both numerical and experimental RC beams strengthened with FRP.

Self-adaptive strategy based on fuzzy control systems for improving performance in wireless sensors networks

The solutions to cope with new challenges that societies have to face nowadays involve providing smarter daily systems. To achieve this, technology has to evolve and leverage physical systems automatic interactions, with less human intervention. Technological paradigms like Internet of Things (IoT) and Cyber-Physical Systems (CPS) are providing reference models, architectures, approaches and tools that are to support cross-domain solutions. Thus, CPS based solutions will be applied in different application domains like e-Health, Smart Grid, Smart Transportation and so on, to assure the expected response from a complex system that relies on the smooth interaction and cooperation of diverse networked physical systems. The Wireless Sensors Networks (WSN) are a well-known wireless technology that are part of large CPS. The WSN aims at monitoring a physical system, object, (e.g., the environmental condition of a cargo container), and relaying data to the targeted processing element. The WSN communication reliability, as well as a restrained energy consumption, are expected features in a WSN. This paper shows the results obtained in a real WSN deployment, based on SunSPOT nodes, which carries out a fuzzy based control strategy to improve energy consumption while keeping communication reliability and computational resources usage among boundaries.

Structural health monitoringby using transmissibility

El control del estado en el que se encuentran las estructuras ha experimentado un gran auge desde hace varias décadas, debido a que los costes de rehabilitación de estructuras tales como los oleoductos, los puentes, los edificios y otras más son muy elevados. En las últimas dos décadas, se han desarrollado una gran cantidad de métodos que permiten identificar el estado real de una estructura, basándose en modelos físicos y datos de ensayos. El ensayo modal es el más común; mediante el análisis modal experimental de una estructura se pueden determinar parámetros como la frecuencia, los modos de vibración y la amortiguación y también la función de respuesta en frecuencia de la estructura. Mediante estos parámetros se pueden implementar diferentes indicadores de daño. Sin embargo, para estructuras complejas y grandes, la implementación de metodologías basadas en la función de respuesta en frecuencia requeriría realizar hipótesis sobre la fuerza utilizada para excitar la estructura. Dado que el análisis modal operacional utiliza solamente las señales de respuesta del sistema para extraer los parámetros dinámicos estructurales y, por tanto, para evaluar el estado de una estructura, el uso de la transmisibilidad sería posible. En este sentido, dentro del análisis modal operacional, la transmisibilidad ha concentrado mucha atención en el mundo científico en la última década. Aunque se han publicado muchos trabajos sobre el tema, en esta Tesis se proponen diferentes técnicas para evaluar el estado de una estructura basándose exclusivamente en la transmisibilidad. En primer lugar, se propone un indicador de daño basado en un nuevo parámetro, la coherencia de transmisibilidad; El indicador se ha valido mediante resultados numéricos y experimentales obtenidos sobre un pórtico de tres pisos. En segundo lugar, la distancia de Mahalanobis se aplica sobre la transmisibilidad como procedimiento para detectar variaciones estructurales provocadas por el daño. Este método se ha validado con éxito sobre una viga libre-libre ensayada experimentalmente. En tercer lugar, se ha implementado una red neuronal basada en medidas de transmisibilidad como metodología de predicción de daño sobre una viga simulada numéricamente. ABSTRACT Structural health monitoring has experienced a huge development from several decades ago since the cost of rehabilitation of structures such as oil pipes, bridges and tall buildings is very high. In the last two decades, a lot of methods able to identify the real stage of a structure have been developed basing on both models and experimental data. Modal testing is the most common; by carrying out the experimental modal analysis of a structure, some parameters, such as frequency, mode shapes and damping, as well as the frequency response function of the structure can be obtained. From these parameters, different damage indicators have been proposed. However, for complex and large structures, any frequency domain approach that relies on frequency response function estimation would be of difficult application since an assumption of the input excitations to the system should be carried out. Operational modal analysis uses only output signals to extract the structural dynamic parameters and, therefore, to identify the structural stage. In this sense, within operational modal analysis, transmissibility has attracted a lot of attention in the scientific field in the last decade. In this work new damage detection approaches based on transmissibility are developed. Firstly, a new theory of transmissibility coherence is developed and it is tested with a three-floor-structure both in simulation and in experimental data analysis; secondly, Mahalanobis distance is taken into use with the transmissibility, and a free-free beam is used to test the approach performance; thirdly, neural networks are used in transmissibility for structural health monitoring; a simulated beam is used to validate the proposed method.