Evaluation of wave drag reduction by flow control

An analytical expression is proposed to estimate the wave drag of an aerofoil equipped with shock control. The analysis extends the conventional approach for a single normal shock wave, based on the knowledge that all types of successful shock control on transonic aerofoils cause bifurcated λ-shock structures. The influence of surface curvature on the λ-shock structure has been taken into account. The extended method has been found to produce fairly good agreement with the results obtained by CFD methods while requiring negligible computational effort. This new formulation is expected to be beneficial in the industrial design process of transonic aerofoils and wings where a large number of computational simulations have to be performed.

Friction of sliding surfaces carrying adsorbed lubricant layers

In concentrated contacts the behaviour of lubricants is much modified by the high local pressures: changes can arise both from molecular ordering within the very thin film lubricant layers present at the interface as well as from the deposition on the component surfaces of more solid-like polymeric boundary layers. These 'third bodies' separating the solid surfaces may have rheological or mechanical properties very different from those observed in the bulk. Classical elasto-hydrodynamic theory considers the entrapped lubricant to exhibit a piezo-viscous behaviour while the conventional picture of more solid boundary lubricant layers views their shear strength r as being linearly dependent on local pressure p, so that T = TO + ap where TO and a are constants. If TO is relatively small, then the coefficient of friction \i = T Ip ~ a and so Amonton's laws are recovered. However, the properties of adsorbed or deposited surface films, or indeed other third bodies such as debris layers, may be more complex than this. A preliminary study has looked quantitatively at the influence of the pressure dependence of the shear strength of any surface layer on the overall friction coefficient of a contact which is made up of an array of asperities whose height varies in a Gaussian manner. Individual contact points may be elastic or plastic. The analysis results in plots of coefficient of friction versus the service or load parameter PIH&NRa where P is the nominal pressure on the contact, HS the hardness of the deforming surface, N the asperity density, R the mean radius of curvature of the asperities, and a is the standard deviation of their height distribution. In principle, any variation oft withp can be incorporated into the model; however, in this initial study we have used data on colloidal suspensions from the group at the Ecole Centrale de Lyon as well as examining the effect of functional relationships of somewhat greater complexity than a simple linear form. Results of the analysis indicate that variations in fj. are possible as the load is varied which depend on the statistical spread of behaviour at individual asperity contacts. The value of this analysis is that it attempts to combine the behaviour of films on the molecular scale with the topography of real engineering surfaces and so give an indication of the effects at the full-size or macro-scale that can be achieved by chemical or molecular surface engineering.

A new alternative for reduction of secondary flows in low pressure turbines

This paper describes a new flow mechanism for the reduction of secondary flows in Low Pressure Turbines using the benefit of contoured endwalls. The extensive application of contoured endwalls in recent years has provided a deeper understanding of the physical phenomenon that governs the reduction of secondary flows. Based on this understanding, the endwall geometry of a linear cascade of solid-thin profiles typical of Low Pressure Turbines has been redesigned. Experimental data are presented for the validation of this new solution. Based on these data, a reduction of 72% in the SKEH and 20% in the mixed-out endwall losses can be obtained. CFD simulations are also presented to illustrate the effect of the new endwall on the secondary flows. Furthermore, an explanation of the flow mechanism that governs the reduction of the SKEH and the losses is given. Copyright © 2006 by ASME.

A novel measurement of dynamic friction

A tribometer, based on a pin-on-disc machine, uses a PZT drive to produce small sinusoidal fluctuations of sliding speed. The frequency and amplitude of these fluctuations can be controlled, and the dynamic response measured. Preliminary test results show that the dynamic friction variation is influenced by the contact materials, normal force, oscillation frequency and steady sliding speed. The variation of friction force amplitude and phase with frequency gives clues about the underlying state variables determining the friction. Modelling studies illustrate the expected behaviour for idealized friction laws governed by, for example, sliding speed, contact temperature, and "rate-state" laws. © 2008 SAE International.

Experimental evidence of flutter and divergence instabilities induced by dry friction

Flutter and divergence instabilities have been advocated to be possible in elastic structures with Coulomb friction, but no direct experimental evidence has ever been provided. Moreover, the same types of instability can be induced by tangential follower forces, but these are commonly thought to be of extremely difficult, if not impossible, practical realization. Therefore, a clear experimental basis for flutter and divergence induced by friction or follower-loading is still lacking. This is provided for the first time in the present article, showing how a follower force of tangential type can be realized via Coulomb friction and how this, in full agreement with the theory, can induce a blowing-up vibrational motion of increasing amplitude (flutter) or an exponentially growing motion (divergence). In addition, our results show the limits of a treatment based on the linearized equations, so that nonlinearities yield the initial blowing-up vibration of flutter to reach eventually a steady state. The presented results give full evidence to potential problems in the design of mechanical systems subject to friction, open a new perspective in the realization of follower-loading systems and of innovative structures exhibiting 'unusual' dynamical behaviors. © 2011 Elsevier Ltd.

Assessing the potential of yield improvements, through process scrap reduction, for energy and CO2 abatement in the steel and aluminium sectors

Targets to cut 2050 CO2 emissions in the steel and aluminium sectors by 50%, whilst demand is expected to double, cannot be met by energy efficiency measures alone, so options that reduce total demand for liquid metal production must also be considered. Such reductions could occur through reduced demand for final goods (for instance by life extension), reduced demand for material use in each product (for instance by lightweight design) or reduced demand for material to make existing products. The last option, improving the yield of manufacturing processes from liquid metal to final product, is attractive in being invisible to the final customer, but has had little attention to date. Accordingly this paper aims to provide an estimate of the potential to make existing products with less liquid metal production. Yield ratios have been measured for five case study products, through a series of detailed factory visits, along each supply chain. The results of these studies, presented on graphs of cumulative energy against yield, demonstrate how the embodied energy in final products may be up to 15 times greater than the energy required to make liquid metal, due to yield losses. A top-down evaluation of the global flows of steel and aluminium showed that 26% of liquid steel and 41% of liquid aluminium produced does not make it into final products, but is diverted as process scrap and recycled. Reducing scrap substitutes production by recycling and could reduce total energy use by 17% and 6% and total CO 2 emissions by 16% and 7% for the steel and aluminium industries respectively, using forming and fabrication energy values from the case studies. The abatement potential of process scrap elimination is similar in magnitude to worldwide implementation of best available standards of energy efficiency and demonstrates how decreasing the recycled content may sometimes result in emission reductions. Evidence from the case studies suggests that whilst most companies are aware of their own yield ratios, few, if any, are fully aware of cumulative losses along their whole supply chain. Addressing yield losses requires this awareness to motivate collaborative approaches to improvement. © 2011 Elsevier B.V. All rights reserved.

Production of freshwater giant prawn using over-wintered juveniles for enhancement of farm income and reduction of rural poverty in Bangladesh

Freshwater giant prawn, Macrobrachium rosenbergii fry produced during late season can not withstand low temperature thus the prawn culture programme during winter is hampered. To overcome this problem, late season (August-September) prawn juveniles (0.9-6.8 g) were stocked at a density of 1.43 to 3.57/square meter in 350-476 square-meter ponds in Pabna and Mymensingh districts during October 2000 and cultured till May 2001. Monthly average water temperature during the winter months (December-February) varied from 16 to 22 °C and gradually increased to 32 °C in May. The prawn fry showed fast growth rate and attained an average weight of 60-70 g within eight months including three winter months. Growth compensation was observed during summer months. Survival rate was 60-79%. After extrapolation of the present growth rate more than 1,600 kg/ha production can be achieved in better-managed ponds. Extrapolated cost of production was Tk. 268,000 and 200,000 Tk./ha in two best ponds, sale value was Tk. 644,9146 [sic] and 528,466 and gross profit was Tk. 376,000-410,000, suggesting a higher economic feasibility of farming freshwater prawn with over-wintered juveniles.

The frequency response of dynamic friction: Model comparisons

Any linearised theory of the initiation of friction-excited vibration via instability of the state of steady sliding requires information about the dynamic friction force in the form of a frequency response function for sliding friction. Recent measurements of this function for an interface consisting of a nylon pin against a glass disc are used to probe the underlying constitutive law. Results are compared to linearised predictions from the simplest ratestate model of friction, and a ratetemperature model. In both cases the observed variation with frequency is not compatible with the model predictions, although there are some significant points of similarity. The most striking result relates to variation of the normal load: any theory embodying the Coulomb relation F∝N would predict behaviour entirely at variance with the measurements, even though the steady friction force obtained during the same measurements does follow the Coulomb law. © 2011 Elsevier Ltd. All rights reserved.

Reduction in Chaetoceros populations by furanace

One of the most promising prophylactic agents being tested to control Penaeus monodon larval diseases is furanace (6-hydroxymethyl-2 2(5-nitro-2-furyl) vinyl pyridine). To evaluate further its suitability as a chemotherapeutic agent, its effects on the population growth of Chaetoceros calcitrans, the diatom used as feed for the zoeal stages, was examined. Chaetoceros populations of uniform density (initial density in all runs: 130-141x10 SUP-3 cells /ml) were placed in nine white, circular (382 sq cm), plastic basins. The physio-chemical characteristics of the culture water were as follows: salinity, 28 . 5-30 . 0 ppt; pH, 8 . 62-8 . 72; temperature, 23-25 . 5 degree C; dissolved oxygen, 7 . 1-9 . 3 ppm; nitrate, 0 . 03-0 . 07 ppm; and ammonia, 0 . 005-0 . 03 ppm. Preweighed furanace granules were dissolved in the culture water, with resulting concentrations of 1 and 2 mg/l (3 replicates each). A set of replicates without furanace served as the control. Population counts of the diatom were taken after 2, 4, 6, 8, and 10 hr exposures. After 4 hr, the population decreased in all three levels. The population in 2 mg/l furanace showed the lowest count and that in control the highest. The population means are not statistically different from one another. The results of the study show that the furanace causes reductions in Chaetoceros population at all durations of exposure.

Application of combined effect of sodium acetate and nisin on reduction of contamination by Listeria monocytogenes in vacuum packaged grass carp (Ctenopharyngodon idella) fillets kept at 4°C

In this study microbiological , chemical quality and fatty acid composition of grass carp (Ctenopharyngodon idella) fillets treated by dipping in sodium acetate (%1 and %3), nisin (% 0.1 and % 0.2) and combination of sodium acetate and nisin was evaluated during 16 days of refrigerated of 4°C Antilisterial effect of nisin was enhanced with the increased concentration of sodium acetate. At day 12 post storage, Listeria monocytogenese count was higher in the control group than the recommended value, however in sodium acetate and nisin treated samples, the count was lower (5.17-5.91 log cfu/g). With increasing the concentrations of sodium acetate, mesophilic counts were lower. Regarding nisin, better results was obtained by applying %0.1 nisin. Greater inhibition of mesophile bacteria was observed when combination treatment was used. The number of lactobacillus was lower when higher concentrations of sodium acetate and nisin were used. Total Volatile Nitrogen values at the end of the experiment were lower in the samples treated with both nisin and sodium acetate and the better results were obtained in combination treatments. Peroxide (PV) at the end of the experiment was 1.9 meq/kg in control, and the lowest values were observed for the treatments 3(%0 sodium acetate +% 0.2 nisin) and 9(%3 sodium acetate +% 0.2 nisin) between 1.08 and 1.62 meq/kg without significant difference. Thiobarbituric acid (TBA) levels at the end of experiment have been shown to be 0.46 mg malonaldehyde per kg in the control. On the other hand treatments 9 had the TBA values of 0.19 mg malonaldehyde per kg which was significantly lower than that of control. Polyunsaturated fatty acids increased by increasing the sodium acetate doses and instead saturated fatty acids and n-6/n-3 ratio decreased. The ratio of UFA/SFA and also C22:6/C16:0 increased when a higher concentration of sodium acetate has been used. The best result obtained by using 3% of sodium acetate but no such relation with nisin was observed.