Investigation of thermal, mechanical and magnetic behaviors of the Cu-11%Al alloy with Ag and Mn additions

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Using Universal Line Model (ULM) for Representing Electromagnetic Transients in Three-Phase Transmission Lines

The second-order differential equations that describe the polyphase transmission line are difficult to solve due to the mutual coupling among them and the fact that the parameters are distributed along their length. A method for the analysis of polyphase systems is the technique that decouples their phases. Thus, a system that has n phases coupled can be represented by n decoupled single-phase systems which are mathematically identical to the original system. Once obtained the n-phase circuit, it's possible to calculate the voltages and currents at any point on the line using computational methods. The Universal Line Model (ULM) transforms the differential equations in the time domain to algebraic equations in the frequency domain, solve them and obtain the solution in the frequency domain using the inverse Laplace transform. This work will analyze the method of modal decomposition in a three-phase transmission line for the evaluation of voltages and currents of the line during the energizing process.

Wizard CD Plus and ProTaper Universal: analysis of apical transportation using new software

Objective: This study has two aims: 1) to evaluate the apical transportation of the Wizard CD Plus and ProTaper Universal after preparation of simulated root canals; 2) to compare, with Adobe Photoshop, the ability of a new software (Regeemy) in superposing and subtracting images. Material and Methods: Twenty five simulated root canals in acrylic-resin blocks (with 20 degrees curvature) underwent cone beam computed tomography before and after preparation with the rotary systems (70 kVp, 4 mA, 10 s and with the 8x8 cm FoV selection). Canals were prepared up to F2 (ProTaper) and 24.04 (Wizard CD Plus) instruments and the working length was established to 15 mm. The tomographic images were imported into iCAT Vision software and CorelDraw for standardization. The superposition of pre- and post-instrumentation images from both systems was performed using Regeemy and Adobe Photoshop. The apical transportation was measured in millimetres using Image J. Five acrylic resin blocks were used to validate the superposition achieved by the software. Student's t-test for independent samples was used to evaluate the apical transportation achieved by the rotary systems using each software individually. Student's t-test for paired samples was used to compare the ability of each software in superposing and subtracting images from one rotary system per time. Results: The values obtained with Regeemy and Adobe Photoshop were similar to rotary systems (P>0.05). ProTaper Universal and Wizard CD Plus promoted similar apical transportation regardless of the software used for image's superposition and subtraction (P>0.05). Conclusion: Wizard CD Plus and ProTaper Universal promoted little apical transportation. Regeemy consists in a feasible software to superpose and subtract images and appears to be an alternative to Adobe Photoshop.

The potential of novel primers and universal adhesives to bond to zirconia

Objectives: To investigate the adhesive potential of novel zirconia primers and universal adhesives to surface-treated zirconia substrates.Methods: Zirconia bars were manufactured (3.0 mm x 3.0 mm x 9.0 mm) and treated as follows: no treatment (C); air abrasion with 35 mu m alumina particles (S); air abrasion with 30 mu m silica particles using one of two systems (Rocatec or SilJet) and; glazing (G). Groups C and S were subsequentially treated with one of the following primers or adhesives: ZP (Z-Prime Plus), AZ (AZ Primer); MP (Monobond Plus); SU (ScotchBond Universal) and; EA (an Experimental Adhesive). Groups Rocatec and SilJet were silanized prior to cementation. Samples form group G were further etched and silanized. Bars were cemented (Multilink) onto bars of a silicate-based ceramic (3.0 mm x 3.0 mm x 9.0 mm) at 90 degrees angle, thermocycled (2.500 cycles, 5-55 degrees C, 30 s dwell time), and tested in tensile strength test. Failure analysis was performed on fractured specimens to measure the bonding area and crack origin.Results: Specimens from group C did not survive thermocycling, while CMP, CSU and CEA groups survived thermocycling but rendered low values of bond strength. All primers presented a better bond performance after air abrasion with Al2O3 particles. SilJet was similar to Rocatec, both presenting the best bond strength results, along with SMP, SSU and CEA. G promoted intermediate bond strength values. Failure mode was predominately adhesive on zirconia surface combined to cohesive of the luting agent.Conclusions: Universal adhesives (MP, SU, EA) may be a considerable alternative for bonding to zirconia, but air abrasion is still previously required. Air abrasion with silica particles followed by silane application also presented high bond strength values. (C) 2013 Elsevier Ltd. All rights reserved.

Prediction of the combustion process in fluidized bed based on physical-chemical properties of biomass particles and their hydrodynamic behaviors

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Universal or provincial? early reception of brian friel´s philadelphia, here I come!

This article, part of a larger research work that resulted in a Professorship Thesis, presents a survey and evaluation of the early reception of one of Brian Friel’s first plays: Philadelphia, Here I Come! (1964). The article also explores the question of emigration from Ireland in the 1950s and 1960s, considering British legislation on the matter, and comments on the eventual influence such issue, among other factors, may have had on criticism about the performance of the play at the time.

Sistema adesivo universal: influência da técnica de condicionamento e da pressão pulpar com soro fetal bovino ou água deionizada na resistência de união à dentina humana

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A característica universal de Leibniz: contextos, trajetórias e implicações

Pós-graduação em Educação Matemática - IGCE

Can Application of Universal Primers Alone Be a Substitute for Airborne-Particle Abrasion to Improve Adhesion of Resin Cement to Zirconia?

Purpose: To determine whether universal primers alone can deliver similar levels of adhesion of resin cement to zirconia ceramic when compared to their application in conjunction with airborne-particle abrasion.Materials and Methods: Sintered zirconia blocks (N = 160) (Lava, 3M ESPE), (5.25 x 5.25 x 3 mm(3)) were embedded in acrylic resin, polished, and randomly distributed into 16 groups (n = 10 per group), according to the factors "universal primer" (8 levels) and "air-particle abrasion" (2 levels): 1. ctr: control, without application of a universal primer; 2. AP: Alloy Primer; 3. MP: Monobond Plus; 4. MZP: Metal Zirconia Primer; 5. MZ: MZ Primer; 6. Sg: Signum Zirconia Bond; 7. SbU: Singlebond Universal; 8. ZP: Z Prime Plus. The universal primers were also used after air abrasion (A) of zirconia to form the following 8 groups: Ctr-A, AP-A, MP-A, MZP-A, MZ-A, Sg-A, SbU-A, and ZP-A. After ultrasonic cleaning, air abrasion was performed using Al2O3 particles (110 mu m, 2.5 bar, 20 s at 10 mm) in a chairside air-abrasion device. After ultrasonic cleaning again, universal primers were applied according to each manufacturer's recommendation. The resin cement (RelyX ARC, 3M ESPE) was built up incrementally and photo-polymerized on the zirconia surface using a silicone mold (empty set = 3.5, height = 3 mm). All specimens were stored in distilled water (60 days at 37 degrees C) and then subjected to shear bond strength testing (SBS) in a universal testing machine (1 mm/min). On a separate set of zirconia specimens, contact angle measurements were made using the sessile drop technique with a goniometer after the application of universal primers on control and air-abraded zirconia surfaces. Data (MPa) were analyzed using one-way ANOVA, Tukey's test, and Student's t-test (alpha = 0.05).Results: When universal primers were used alone, SbU presented significantly higher mean SBS (19.5 +/- 5.8) that did the other primers (0 to 9.9 +/- 6.6) (p = 0.001). When air abraded, the groups AP-A (14.1 +/- 6.1), MP-A (15.9 +/- 5.4), ZP-A (16.9 +/- 7.3), SG-A (19.1 +/- 2.1), SbU-A (12 +/- 1.5) showed significant differences (p = 0.03). Adhesive performance of all universal primers was enhanced after air abrasion, with the exception of the SbU and MZ primers. After air abrasion, contact angle measurements were lower for the each primer (without air abrasion: 28.9 to 83.9; with air abrasion: 27.1 to 63.0), except for MZP.Conclusion: Air abrasion with 110 mu m Al2O3 followed by universal primer application increased the bond strength of tested resin cement to zirconia, with the exception of SbU and MZ.

Cleaning capacity promoted by motor-driven or manual instrumentation using ProTaper Universal system: Histological analysis

The aim of this study was to assess the cleaning capacity of the Protaper system using motor-driven or manual instrumentation. Materials and Methods: Ten mandibular molars were randomly separated into 2 groups (n = 5) according to the type of instrumentation performed, as follows: Group 1 - instrumentation with rotary nickel-titanium (Ni-Ti) files using ProTaper Universal System (Dentsply/Maillefer); and, Group 2 - instrumentation with Ni-Ti hand files using ProTaper Universal (Dentsply-Maillefer). Afterwards, the teeth were sectioned transversely and submitted to histotechnical processing to obtain histological sections for microscopic evaluation. The images were analyzed by the Corel Photo-Paint X5 program (Corel Corporation) using an integration grid superimposed on the image. Results: Statistical analysis (U-Mann-Whitney - P < 0.05) demonstrated that G1 presented higher cleaning capacity when compared to G2. Conclusions: The rotary technique presented better cleaning results in the apical third of the root canal system when compared to the manual technique.

Association between risk behaviors and adiposity indicators in adolescents from Southern Brazil: A methodological approach

The aim of this study was to analyze the association between risk behaviors and adiposity indicators in adolescents and to discuss some methodological aspects related to this relationship. We evaluated 1,321 adolescents (55.2% female) aged 10-16 years. Relative body fat (%fat) by measurement of triceps and subscapular skinfold thickness and waist circumference (WC) were used as total and central adiposity indicators, respectively. Physical inactivity, time spent in front of the TV, the consumption of soda and/or chocolate, alcohol, and tobacco smoking were analyzed as risk behaviors. Information about the socioeconomic status (categorized into three levels) and nutritional status of the mother (overweight or normal weight) were used as adjustment factors in the analyses of prevalence ratio (PR) of the outcomes and their associated 95% confidence intervals (95% CI). The chi-square test and Poisson regression were used for statistical analyses. Low associations were found between risk behaviors and adiposity indicators. Tobacco smoking was the most positively correlated behavior with adiposity in girls (%fat: PR = 1.61; 95% CI = 1.04-2.47; WC: PR = 1.90; 95% CI = 1.17-3.08) and in adolescents whose mothers were normal weight (%fat: PR = 2.31; 95% CI = 1.33-4.03; WC: PR: 2.31; CI: 1.19-4.46). Additionally, as an important methodological issue, we highlighted the assessment of risk behaviors in adolescents as crucial to producing more robust evidence on the subject. Of the investigated behaviors, we concluded that tobacco smoking is the behavior most associated with adiposity indicators.

Resistência de união e estabilidade de um sistema adesivo universal à dentina erodida/abrasionada após desproteinização

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sentimento de culpa na obra freudiana: universal e inconsciente

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Religião, política e eleições na Folha Universal

The Folha Universal, newspaper produced by the Igreja Universal do Reino de Deus (Iurd, abbreviation in Portuguese for Universal Church of the Kingdom of God), reaches an average weekly circulation from 2.5 to 3.5 million copies. Studies indicate that the Folha Universal is not merely an institutional newspaper. It is systematically dedicated to be a source of political information to their readers, in order to publicize candidates and politicians who defend the Iurd’s proposals for the Brazilian public life. This paper describes results of an empirical study on the frames built by the Folha Universal about the social demands, economic and political governance considered as priorities to the public management by the Iurd around five themes of analysis: public safety; children and adolescents care; public health; environment; politics and economy. The results indicate that, as characteristics of the Folha Universal in the four months prior to the 2010 Brazilian elections, aspects that differ from those indicated by previous studies on the newspaper. Previously detected in the pages of Folha Universal as a mean for finding solutions to social problems, the theology of prosperity was in our sample replaced by the formulation of public policies.

Design universal e acessibilidade: análise ergonomica de equipamentos de ginástica em espaços públicos

In recent years the availability of equipment for exercise in public places increased demand on the principles of universal design, ergonomics and accessibility, since they are intended for use by many different users. This paper presents an analysis of ergonomic equipment and discusses the main problems observed, as well as projective presents parameters for the development of new products.