Desenvolvimento de microcápsulas ativadas por radiação solar para aplicação em painéis cerâmicos exteriores

Dissertação de mestrado integrado em Engenharia de Materiais

Introducing a new MRI classification of lumbar spinal stenosis based on cross-sectional morphology of the dural sac : 37

Introduction: Measures of the degree of lumbar spinal stenosis (LSS) such as antero-posterior diameter of the canal, and dural sac cross sectional area vary, and do not correlate with symptoms or results of surgery. We created a grading system, comprised of seven categories, based on the morphology of the dural sac and its contents as seen on T2 axial images. The categories take into account the ratio of rootlet/ CSF content. Grade A indicates no significant compression, grade D is equivalent to a total myelograhic block. We compared this classification with commonly used criteria of severity of stenosis. Methods: Fifty T2 axial MRI images taken at disc level from 27 symptomatic LSS patients undergoing decompressive surgery were classified twice by two radiologists and three spinal surgeons working at different institutions and countries. Dural sac cross-sectional surface area and AP diameter of the canal were measured both at disc and pedicle level from DICOM images using OsiriX software. Intraand inter-observer reliability were assessed using Cohen's, Fleiss' kappa statistics, and t test. Results: For the morphological grading the average intra-and inter observer kappas were 0.76 and 0.69+, respectively, for physicians working in the study originating country. Combining all observers the kappa values were 0.57 ± 0.19. and 0.44 ± 0.19, respectively. AP diameter and dural sac cross-sectional area measurements showed no statistically significant differences between observers. No correlation between morphological grading and AP diameter or dural sac crosssectional areawas observed in 13 (26%) and 8 cases (16%), respectively. Discussion: The proposed morphological grading relies on the identification of the dural sac and CSF better seen on full MRI series. This was not available to the external observers, which might explain the lower overall kappa values. Since no specific measurement tools are needed the grading suits everyday clinical practice and favours communication of degree of stenosis between practising physicians. The absence of a strict correlation with the dural sac surface suggests that measuring the surface alone might be insufficient in defining LSS as it is essentially a mismatch between the spinal canal and its contents. This grading is now adopted in our unit and further studies concentrating on relation between morphology, clinical symptoms and surgical results are underway.

Cristallochemical characterization of synthetic Zn-substituted maghemites (g-Fe2-xZn xO3)

Maghemite (g-Fe2O3) is the most usually found ferrimagnetic oxide in red basalt-derived soils. The variable degrees of ionic substitution of Fe3+ for different metals (e.g. Ti4+, Al3+, Mg2+, Zn2+, and Mn2+) and non-metals in the maghemite structure influence some cristallochemical features of this iron oxide. In this study, synthetic Zn-substituted maghemites were prepared by co-precipitation in alkaline aqueous media of FeSO4.7H2O with increasing amounts of ZnSO4.7H2O to obtain the following sequence of Fe3+ for Zn2+ substitutions: 0.0, 0.025, 0.05, 0.10, 0.15, 0.20, and 0.30 mol mol-1. The objective of this work was to evaluate the cristallochemical alterations of synthetic Zn-substituted maghemites. The dark black synthetic precipitated material was heated to 250 °C during 4 h forming a brownish maghemite that was characterized by chemical analysis as well as X ray diffraction (XRD), specific surface area and mass-specific magnetic susceptibility. The isomorphic substitution levels observed were of 0.0013, 0.0297, 0.0590, 0.1145, 0.1764, 0.2292 and 0.3404 mol mol-1, with the formation of a series of maghemites from Fe2Zn0O3 to Fe(1.49)Zn(0.770)O3 . The increase in Fe3+ for Zn2+ substitution, [Zn mol mol-1] increased the dimension a0 of the cubic unit cells of the studied maghemites according to the regression equation: a0 = 0.8343 + 0.02591Zn (R² = 0.98). On the other hand, the mean crystallite dimension and mass-specific magnetic susceptibility of the studied maghemites decreased with increasing isomorphic substitution.

Effect of Grooved Concrete on Curing Efficiency, MLR-83-4, 1983

The textured concrete surface on all PCC primary paving projects (and when specified on secondary projects) is required to be grooved in a specified manner. The laboratory test for determining the efficiency index of concrete curing compounds is made on slabs that are not grooved. This short investigation was undertaken to determine any changes in the curing efficiency index when using various rates of application of curing compound on grooved concrete. Currently a 95 percent curing efficiency index is specified at an application rate of 15 square yards per gallon. Can this efficiency be achieved, and if so at what application rate, on grooved concrete? Grooving the concrete greatly increases the surface area and also causes the liquid curing compound to run off the high spots and collect in the grooves.

A new concept of integrated cardiopulmonary bypass circuit.

OBJECTIVE: Standard cardiopulmonary bypass (CPB) circuits with their large surface area and volume contribute to postoperative systemic inflammatory reaction and hemodilution. In order to minimize these problems a new approach has been developed resulting in a single disposable, compact arterio-venous loop, which has integral kinetic-assist pumping, oxygenating, air removal, and gross filtration capabilities (CardioVention Inc., Santa Clara, CA, USA). The impact of this system on gas exchange capacity, blood elements and hemolysis is compared to that of a conventional circuit in a model of prolonged perfusion. METHODS: Twelve calves (mean body weight: 72.2+/-3.7 kg) were placed on cardiopulmonary bypass for 6 h with a flow of 5 l/min, and randomly assigned to the CardioVention system (n=6) or a standard CPB circuit (n=6). A standard battery of blood samples was taken before bypass and throughout bypass. Analysis of variance was used for comparison. RESULTS: The hematocrit remained stable throughout the experiment in the CardioVention group, whereas it dropped in the standard group in the early phase of perfusion. When normalized for prebypass values, both profiles differed significantly (P<0.01). Both O2 and CO2 transfers were significantly improved in the CardioVention group (P=0.04 and P<0.001, respectively). There was a slightly higher pressure drop in the CardioVention group but no single value exceeded 112 mmHg. No hemolysis could be detected in either group with all free plasma Hb values below 15 mg/l. Thrombocyte count, when corrected by hematocrit and normalized by prebypass values, exhibited an increased drop in the standard group (P=0.03). CONCLUSION: The CardioVention system with its concept of limited priming volume and exposed foreign surface area, improves gas exchange probably because of the absence of detectable hemodilution, and appears to limit the decrease in the thrombocyte count which may be ascribed to the reduced surface. Despite the volume and surface constraints, no hemolysis could be detected throughout the 6 h full-flow perfusion period.

Natriumsilikaatin liuotuslaitoksen kapasiteetin nosto

Tässä työssä tutkittiin natriumsilikaatin (vesilasi) liuotukseen ja suodatukseen vaikuttavia tekijöitä. Työssä pyrittiin optimoimaan natriumsilikaatin liuotus- ja suodatuskapasiteetti J. M. Huber Finland Oy:n Haminan tehtaan liuotuslaitoksella. Kirjallisuusosassa perehdyttiin kiinteän natriumsilikaatin ja natriumsilikaatin vesiliuoksen ominaisuuksiin, sekä käsiteltiin soveltuvin osin liuotuksen ja suodatuksen teoriaa. Kokeellisessa osassa vertailtiin kahden eri valmistajan natriumsilikaatteja toisiinsa, sekä pyrittiin löytämään molemmille laseille optimaalisimmat prosessiparametrit liuotus- ja suodatuskokeiden avulla. Erilaisia prosessiparametreja ja ajotapoja testattiin tehdasmittakaavan koeajoilla todellisilla prosessilaitteilla. Eri natriumsilikaattien vertailu tehtiin tehdasmittakaavan koeajojen sekä laboratorioanalyysien avulla. Koeajojen tulosten perusteella Taavetista toimitettu vesilasi liukenee nopeammin kuin Puolasta toimitettu ostolasi, mutta puolalaisesta lasista liuotettu silikaatti suodattuu helpommin kuin Taavetin lasista liuotettu silikaatti. Liukenemisnopeuden eroon selitettävissä Taavetin lasin suuremmalla ominaispinta-alalla sekä hauraammalla rakenteella. Suodatuseroon ei löytynyt yksiselitteistä syytä, joten sen löytämiseksi vaadittaisiin jatkotutkimuksia. Kokeiden perusteellaparas keino puolalaisen lasin liuotuksen nopeuttamiseen olisi pitää liuotussäiliön lasiylimäärä mahdollisimman korkeana jokaisessa panoksessa ja nopeuttaa liuotussäiliön panostusta lasin ja veden yhtäaikaisella annostelulla. Tulosten perusteella paras keino Taavetin lasista liuotetun silikaatin suodatuksen helpottamiseen olisi laskea liuoksen tavoitetiheyttä nykyisestä arvostaan, jolloin viskositeetti pienenee merkittävästi ja suodatus onnistuu liuotuslaitoksen kapasiteetin kannalta paremmin. Edellä mainituilla ajotavoilla tehtyjen koeajojen perusteella, molemmilla laseilla on mahdollista päästä 150 MT/d tavoitekapasiteettiin, mutta varmin tapa kyseisen kapasiteetin saavuttamiseksi olisi lisätä suodatuskapasiteettia investoimalla toiseen silikaattisuodattimeen.

Korkeakappa-massan suotatuvuus

Työn tarkoituksena oli tutkia korkeakappa-massan suotautuvuutta sekä etsiä uusia analyysimenetelmiä korkeakappa-massan karakterisoimiseksi. Työssä pyrittiin määrittämään tekijöitä, jotka vaikuttavat korkeakappa-massan suotautumiseen. Työn kirjallisessa osassa tarkasteltiin aluksi yleisesti keiton teoriaa, minkä jälkeen käsiteltiin jauhatusta ja tarkemmin korkeakappa-massan hienovaraisempaa jauhatusta eli kuidutusta. Seuraavaksi käsiteltiin suodatusta ja sen teoriaa sekä suodatukseen vaikuttavia tekijöitä. Massan pesusta esitettiin perusteet ja teoriaa. Lopuksi tarkasteltiin massan karakterisointia eri lähestymistavoilla sekä kuitujen perusominaisuuksia. Kokeellisessa osassa verrattiin LTY:n koesuodatuslaitteistolla tehdyillä suodatuskokeilla korkeakappa-massaisen sellukakun suotautuvuutta eri paine-eroilla, suodoksen eri hienoainepitoisuuksilla sekä ennen ja jälkeen sellutehtaallatapahtuneen kuidutuksen. Savonlinnassa sijaitsevalla laitteistolla tehtiin syrjäytystestejä ennen ja jälkeen kuidutusta otetuilla sellumassoilla. Lisäksi ennenja jälkeen kuidutusta otettuja sellumassanäytteitä karakterisoitiin mm. kuituanalysaattorilla, huokoskoko- ja ominaispinta-ala-analyyseillä sekä SEM-kuvilla. Suodatuskokeissa hienoainepitoisuudella ei ollut merkitystä permeabiliteettiin mitattujen suodosvirtausten perusteella. Kuten Darcyn lain perusteella voitiin olettaa, kakun paine-eron kasvaessa permeabiliteetti kasvoi. Vaikutus ei ollut kuitenkaan lineaarinen paine-eroon verrattuna vaan kakun permeabiliteetti kasvoi enemmän tietyllä paine-erovälillä. Tämä paine-eroväli vaihteli hieman riippuen oliko sellumassa otettu ennen vai jälkeen kuidutusta. Lappeenrannassa tehdyissä suodatuskokeissa ei ennen ja jälkeen kuidutusta otetuilla näytteillä ollut selvää eroa permeabiliteeteissa, mutta Savonlinnan syrjäytystesteissä ero syrjäytymisnopeudessa oli selvä. Ennen ja jälkeen kuidutusta otettujen sellumassojen kuituanalysaattorituloksissa ja SEM-kuvissa ei havaittu eroa näytteiden välillä, mutta massojen huokoskoko muuttui kuidutuksen vaikutuksesta.

Ação promotora do berílio em catalisadores da síntese do estireno

The catalytic dehydrogenation of ethylbenzene in presence of steam is the main commercial route to produce styrene. The industrial catalysts are potassium- and chromia-doped hematite which show low surface areas leading to bad performance and short life. In order to develop catalysts with high areas, the effect of beryllium on the textural properties and on the catalytic performance of this iron oxide was studied. The influence of the amount of the dopant, the starting material and the calcination temperature were also studied. In sample preparations, iron and beryllium salts (nitrate or sulfate) were hydrolyzed with ammonia and then calcinated. The experiments followed a factorial design with two variables in two levels (Fe/Be= 3 and 7; calcination temperature= 500 and 700ºC). Solids without any dopant were also prepared. Samples were characterized by elemental analysis, infrared spectroscopy, surface area and porosity measurements, X-ray diffraction, DSC and TG. The catalysts were tested in a microreactor at 524ºC and 1 atm, by using a mole ratio of steam/ ethylbenzene=10. The selectivity was measured by monitoring styrene, benzene and toluene formation. It was found that the effect of beryllium on the characteristics of hematite and on its catalytic performance depends on the starting material and on the amount of dopant. Surface areas increased due to the dopant as well as the nature of the precursor; samples produced by beryllium sulfate showed higher areas. Beryllium-doped solids showed a higher catalytic activity when compared to pure hematite, but no significant influence of the anion of starting material was noted. It can be concluded that beryllium acts as both textural and structural promoter. Samples with Fe/Be= 3, heated at 500ºC, lead to the highest conversion and were the most selective. However, catalysts prepared from beryllium sulfate are the most promising to ethylbenzene dehydrogenation due to their high surface area which could lead to a longer life.

Connectivity in sol-gel silica glasses

In this work it is carried out a review on structural parameters related to the evaluation of pore connectivity of nanostructures. The work describes parameters and methods of evaluation of geometric parameters. The concepts of connectivity are applied to silica gels and glasses obtained from sol-gel process. The study of pores connectivity was carried out using a combination of geometric modeling and experimental evaluation of specific surface area and pore volume. The permeability of the pore structure is evaluated and a permeability geometric factor, Pg, is proposed.

Principais métodos de caracterização da porosidade de resinas à base de divinilbenzeno

This paper reviews the most important methods used to characterize the porosity of styrene-divinylbenzene resins. Methods such as adsorption of nitrogen for determination of surface area and mercury intrusion porosimetry for characterization of pore size distribution are related.

Síntese de membranas cerâmicas via método sol-gel utilizando TEOS e N,N-dimetilformamida

In this work we obtained microporous and mesoporous silica membranes by sol-gel processing. Tetraethylortosilicate (TEOS) was used as precursor. Nitric acid was used as catalyst. In order to study the affect of N,N-dimethylformamide (NDF) as drying additive, we used a molar ratio TEOS/NDF of 1/3. The performance of N,N-dimethylformamide was evaluated through monolithicity measurements. The structural evolutions occurring during the sol-gel transition and in the interconnected network of the membranes during thermal treatment were monitored by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analyses and nitrogen sorption. We noted that in the presence of N,N-dimethylformamide, polymerization goes through a temporary stabilization of oligomers. The Si-O(H) bonds are stronger and belong to a more cross-linked structure for the N,N-dimethylformamide containing sol. The membranes obtained in the presence of N,N-dimethylformamide have larger surface area and its pore structure is in the range of mesoporous. The membranes obtained without additive have pore structure in the range of microporous.

Argilas bentoníticas da península de Santa Elena, Equador: pilarização, ativação ácida e seu uso como descolorante de óleo de soja

Two samples of calcic bentonite of the Santa Elena Peninsula, Ecuador, were pillared with Al13 ions in the ratio of 10, 15 and 20 meq of Al g-1 of clay, calcinated at 573, 723 and 873 ºK and acid activated with 4, 6 and 8 mol L-1 H2SO4. Analyses by X-ray diffraction, X-ray fluorescence, differential and gravimetric thermal, density, surface area and porosity, were applied in order to study the modifications occurred in the crystalline structure of the montmorillonite. The 8 mol L-1 H2SO4 acid-activated 15 meq of Al g-1 of clay at 573 ºK Al-pillared samples indicated the best results in the bleaching of the soybean oil measured by UV-visible spectrophotometer.

Avaliação da porosidade de microcápsulas contendo proteína bioativa por porosimetria de mercúrio e adsorção de nitrogênio

Microcapsules containing lactoferrin were produced by spray drying using dextrin:octenylsuccinate starch, as wall materials. Porosity characteristics of spray-dried microcapsules were investigated by mercury intrusion porosimetry and nitrogen adsorption. The outer and inner structures of microcapsules were studied by Scanning Electron Microscopy and sizes were determined by Laser Diffraction. Results indicate that all microcapsules presents adsorption isotherm of type II and that micropores on the microcapsules surface will be very few or none. Our results show that microstructure, surface area and size of microcapsules are affected by dextrin: octenylsuccinate starch proportion. Pore characteristics for various microcapsules are found to be different.

Nanotubos de TiO2 dopados com nitrogênio: comparação das atividades fotocatalíticas de materiais obtidos através de diferentes técnicas

TiO2 nanotubes were synthesized by hydrothermal method and doped with three nitrogen compounds to enhance photocatalytic activity under visible light. Catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS) and specific surface area and pore volume determined by BET and BJH methods, respectively. Photocatalytic activity was evaluated by photodegradation of rhodamine B under visible and UV radiations. Results showed doped-nanotubes were more efficient under visible light. The best photocatalytic activity was for sample NTT-7-600/NH3I, being 30% higher than the non-doped sample.

Use of new silica fillers as additives for polymers used in packaging of fruit

The objective of this work was to synthesize nanosilicas with different degree of hydrophobicity by the sol-gel method, using tetraethyl orthosilicate as a precursor. For this purpose, 3-aminopropyl triethoxysilane (APS) and 1,1,1,3,3,3 - hexamethyldisilazane (HMDS), were added during synthesis as modifiers. A commercial biopolymer (Hexamoll Dinch, BASF) intended for packaging of apples, was added to the new nanosilicas. The materials obtained were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, potentiometric titration, porosity, specific surface area and hydrophobicity/hydrophilicity by wetting test. Colorimetry was used to evaluate change in apple pulp color after contact with the different silicas.