Feasibility of combined wind-wave energy platforms

The European Union has set out an ambitious 20% target for renewable energy use by 2020. It is expected that this will be met mainly by wind energy. Looking towards 2050, reductions in greenhouse gas emissions of 80-95% are to be sought. Given the issues securing this target in the transport and agriculture sectors, it may only be possible to achieve this target if the power sector is carbon neutral well in advance of 2050. This has permitted the vast expansion of offshore renewables, wind, wave and tidal energy. Offshore wind has undergone rapid development in recent years however faces significant challenges up to 2020 to ensure commercial viability without the need for government subsidies. Wave energy is still in the very early stages of development so as yet there has been no commercial roll out. As both of these technologies are to face similar challenges in ensuring they are a viable alternative power generation method to fossil fuels, capitalising on the synergies is potentially a significant cost saving initiative. The advent of hybrid solutions in a variety of configurations is the subject of this thesis. A singular wind-wave energy platform embodies all the attributes of a hybrid system, including sharing space, transmission infrastructure, O&M activities and a platform/foundation. This configuration is the subject of this thesis, and it is found that an OWC Array platform with multi-MegaWatt wind turbines is a technically feasible, and potentially an economically feasible solution in the long term. Methods of design and analysis adopted in this thesis include numerical and physical modelling of power performance, structural analysis, fabrication cost modelling, simplified project economic modelling and time domain reliability modelling of a 210MW hybrid farm. The application of these design and analysis methods has resulted in a hybrid solution capable of producing energy at a cost between €0.22/kWh and €0.31/kWh depending on the source of funding for the project. Further optimisation through detailed design is expected to lower this further. This thesis develops new and existing methods of design and analysis of wind and wave energy devices. This streamlines the process of early stage development, while adhering to the widely adopted Concept Development Protocol, to develop a technically and economically feasible, combined wind-wave energy hybrid solution.

Optical micro- and nanofibres: Higher mode generation and particle manipulation studies

This thesis is centred on two experimental fields of optical micro- and nanofibre research; higher mode generation/excitation and evanescent field optical manipulation. Standard, commercial, single-mode silica fibre is used throughout most of the experiments; this generally produces high-quality, single-mode, micro- or nanofibres when tapered in a flame-heated, pulling rig in the laboratory. Single mode fibre can also support higher transverse modes, when transmitting wavelengths below that of their defined single-mode regime cut-off. To investigate this, a first-order Laguerre-Gaussian beam, LG01 of 1064 nm wavelength and doughnut-shaped intensity profile is generated free space via spatial light modulation. This technique facilitates coupling to the LP11 fibre mode in two-mode fibre, and convenient, fast switching to the fundamental mode via computer-generated hologram modulation. Following LP11 mode loss when exponentially tapering 125μm diameter fibre, two mode fibre with a cladding diameter of 80μm is selected fir testing since it is more suitable for satisfying the adiabatic criteria for fibre tapering. Proving a fruitful endeavour, experiments show a transmission of 55% of the original LP11 mode set (comprising TE01, TM01, HE21e,o true modes) in submicron fibres. Furthermore, by observing pulling dynamics and progressive mode-lass behaviour, it is possible to produce a nanofibre which supports only the TE01 and TM01 modes, while suppressing the HE21e,o elements of the LP11 group. This result provides a basis for experimental studies of atom trapping via mode-interference, and offers a new set of evanescent field geometries for sensing and particle manipulation applications. The thesis highlights the experimental results of the research unit’s Cold Atom subgroup, who successfully integrated one such higher-mode nanofibre into a cloud of cold Rubidium atoms. This led to the detection of stronger signals of resonance fluorescence coupling into the nanofibre and for light absorption by the atoms due to the presence of higher guided modes within the fibre. Theoretical work on the impact of the curved nanofibre surface on the atomic-surface van der Waals interaction is also presented, showing a clear deviation of the potential from the commonly-used flat-surface approximation. Optical micro- and nanofibres are also useful tools for evanescent-field mediated optical manipulation – this includes propulsion, defect-induced trapping, mass migration and size-sorting of micron-scale particles in dispersion. Similar early trapping experiments are described in this thesis, and resulting motivations for developing a targeted, site-specific particle induction method are given. The integration of optical nanofibres into an optical tweezers is presented, facilitating individual and group isolation of selected particles, and their controlled positioning and conveyance in the evanescent field. The effects of particle size and nanofibre diameter on pronounced scattering is experimentally investigated in this systems, as are optical binding effects between adjacent particles in the evanescent field. Such inter-particle interactions lead to regulated self-positioning and particle-chain speed enhancements.

Voltage properties of optically injected long wavelength VCSELs: Theory and experiment

Future high speed communications networks will transmit data predominantly over optical fibres. As consumer and enterprise computing will remain the domain of electronics, the electro-optical conversion will get pushed further downstream towards the end user. Consequently, efficient tools are needed for this conversion and due to many potential advantages, including low cost and high output powers, long wavelength Vertical Cavity Surface Emitting Lasers (VCSELs) are a viable option. Drawbacks, such as broader linewidths than competing options, can be mitigated through the use of additional techniques such as Optical Injection Locking (OIL) which can require significant expertise and expensive equipment. This thesis addresses these issues by removing some of the experimental barriers to achieving performance increases via remote OIL. Firstly, numerical simulations of the phase and the photon and carrier numbers of an OIL semiconductor laser allowed the classification of the stable locking phase limits into three distinct groups. The frequency detuning of constant phase values (ø) was considered, in particular ø = 0 where the modulation response parameters were shown to be independent of the linewidth enhancement factor, α. A new method to estimate α and the coupling rate in a single experiment was formulated. Secondly, a novel technique to remotely determine the locked state of a VCSEL based on voltage variations of 2mV−30mV during detuned injection has been developed which can identify oscillatory and locked states. 2D & 3D maps of voltage, optical and electrical spectra illustrate corresponding behaviours. Finally, the use of directly modulated VCSELs as light sources for passive optical networks was investigated by successful transmission of data at 10 Gbit/s over 40km of single mode fibre (SMF) using cost effective electronic dispersion compensation to mitigate errors due to wavelength chirp. A widely tuneable MEMS-VCSEL was established as a good candidate for an externally modulated colourless source after a record error free transmission at 10 Gbit/s over 50km of SMF across a 30nm single mode tuning range. The ability to remotely set the emission wavelength using the novel methods developed in this thesis was demonstrated.

A history of the Irish Red Cross Society, 1939-1971

This research is concerned with assessing from a national perspective the role, work and historical impact of the Irish Red Cross Society (IRCS) between 1939 and 1971. During this period the IRCS discharged three primary functions: it provided first aid services both in war-time and peace-time; it pioneered public health and social care services; and acted as the State’s main agency for international humanitarian relief measures. Although primarily a national organisational history of the Society, it is not a history in isolation. A broader perspective demonstrates that the work undertaken by the IRCS has relevance to the medical, social, religious, cultural, political and diplomatic history of twentieth century Ireland. This study assesses the impact of a number of significant public health and social care initiatives which the IRCS implemented and developed since its inception and how most of these were subsequently developed independently by the State. During the early 1940s, the Society’s formation of a national blood transfusion service ultimately laid the foundations for the establishment of a national blood transfusion service. The Society’s steering of a national anti-tuberculosis campaign in the 1940s brought the issue of the eradication of TB to the fore and helped to change public attitudes towards the disease. The concept of caring for the needs of the elderly in Ireland was largely unknown until the IRCS began addressing the issue in the 1950s and, for more than two decades, was effectively the only organisation in the State that campaigned and introduced innovative services for the aged. The IRCS made a significant impact in terms of its commitment to the needs of refugees and the provision of international humanitarian relief from Ireland. The Society’s donation in 1945 of a fully equipped hospital to the population of Saint-Lo in France, its war-time overseas relief efforts and its post-war work for child refugees earned Ireland significant international recognition and prestige and, more importantly, justified Ireland’s war-time policy of neutrality. With Ireland’s admission to the UN, the government became more dependent on the IRCS to consolidate that position.

Burst-mode electronic dispersion compensation in long reach PONs

Long reach passive optical networks (LR-PONs), which integrate fibre-to-the-home with metro networks, have been the subject of intensive research in recent years and are considered one of the most promising candidates for the next generation of optical access networks. Such systems ideally have reaches greater than 100km and bit rates of at least 10Gb/s per wavelength in the downstream and upstream directions. Due to the limited equipment sharing that is possible in access networks, the laser transmitters in the terminal units, which are usually the most expensive components, must be as cheap as possible. However, the requirement for low cost is generally incompatible with the need for a transmitter chirp characteristic that is optimised for such long reaches at 10Gb/s, and hence dispersion compensation is required. In this thesis electronic dispersion compensation (EDC) techniques are employed to increase the chromatic dispersion tolerance and to enhance the system performance at the expense of moderate additional implementation complexity. In order to use such EDC in LR-PON architectures, a number of challenges associated with the burst-mode nature of the upstream link need to be overcome. In particular, the EDC must be made adaptive from one burst to the next (burst-mode EDC, or BM-EDC) in time scales on the order of tens to hundreds of nanoseconds. Burst-mode operation of EDC has received little attention to date. The main objective of this thesis is to demonstrate the feasibility of such a concept and to identify the key BM-EDC design parameters required for applications in a 10Gb/s burst-mode link. This is achieved through a combination of simulations and transmission experiments utilising off-line data processing. The research shows that burst-to-burst adaptation can in principle be implemented efficiently, opening the possibility of low overhead, adaptive EDC-enabled burst-mode systems.

“Something isn’t right here”: American exceptionalism and the creative nonfiction of the Vietnam War

In this thesis, I argue that few attempts were as effective in correcting the exceptionalist ethos of the United States than the creative nonfiction written by the veterans and journalists of the Vietnam War. Using critical works on creative nonfiction, I identify the characteristics of the genre that allowed Paul John Eakin to call it ‘a special kind of fiction.’ I summarise a brief history of creative nonfiction to demonstrate how it became a distinctly American form despite its Old World origins. I then claim that it was the genre most suited to the kind of ideological transformation that many hoped to instigate in U.S. society in the aftermath of Vietnam. Following this, the study explores how this “new” myth-making process occurred. I use Tim O’Brien’s If I Die in a Combat Zone and Philip Caputo’s A Rumor of War to illustrate how autobiography/memoir was able to demonstrate the detrimental effect that America’s exceptionalist ideology was having on its population. Utilising narrative and autobiographical theory, I contend that these accounts represented a collective voice which spoke for all Americans in the years after Vietnam. Using Neil Sheehan’s A Bright Shining Lie and C.D.B. Bryan’s Friendly Fire, I illustrate how literary journalism highlighted the hubris of the American government. I contend that while poiesis is an integral attribute of creative nonfiction, by the inclusion of extraneous bibliographic material, authors of the genre could also be seen as creating a literary context predisposing the reader towards an empirical interpretation of the events documented within. Finally, I claim that oral histories were in their essence a synthesis of “everyman” experiences very much in keeping with the American zeitgeist of the early Eighties. Focussing solely on Al Santoli’s Everything We Had, I demonstrate how such polyphonic narratives personalised the history of the Vietnam War.

First principles simulation of amorphous silicon bulk, interfaces, and nanowires for photovoltaics

Amorphous silicon has become the material of choice for many technologies, with major applications in large area electronics: displays, image sensing and thin film photovoltaic cells. This technology development has occurred because amorphous silicon is a thin film semiconductor that can be deposited on large, low cost substrates using low temperature. In this thesis, classical molecular dynamics and first principles DFT calculations have been performed to generate structural models of amorphous and hydrogenated amorphous silicon and interfaces of amorphous and crystalline silicon, with the ultimate aim of understanding the photovoltaic properties of core-shell crystalline amorphous Si nanowire structures. We have shown, unexpectedly, from the simulations, that our understanding of hydrogenated bulk a-Si needs to be revisited, with our robust finding that when fully saturated with hydrogen, bulk a-Si exhibits a constant optical energy gap, irrespective of the hydrogen concentration in the sample. Unsaturated a-Si:H, with a lower than optimum hydrogen content, shows a smaller optical gap, that increases with hydrogen content until saturation is reached. The mobility gaps obtained from an analysis of the electronic states show similar behavior. We also obtained that the optical and mobility gaps show a volcano curve as the H content is varied from 7% (undersaturation) to 18% (mild oversaturation). In the case of mild over saturation, the mid-gap states arise exclusively from an increase in the density of strained Si-Si bonds. Analysis of our structures shows the extra H atoms in this case form a bridge between neighboring silicon atoms which increases the corresponding Si-Si distance and promotes bond length disorder in the sample. That has the potential to enhance the Staebler-Wronski effect. Planar interface models of amorphous-crystalline silicon have been generated in Si (100), (110) and (111) surfaces. The interface models are characterized by structure, RDF, electronic density of states and optical absorption spectrum. We find that the least stable (100) surface will result in the formation of the thickest amorphous silicon layer, while the most stable (110) surface forms the smallest amorphous region. We calculated for the first time band offsets of a-Si:H/c-Si heterojunctions from first principles and examined the influence of different surface orientations and amorphous layer thickness on the offsets and implications for device performance. The band offsets depend on the amorphous layer thickness and increase with thickness. By controlling the amorphous layer thickness we can potentially optimise the solar cell parameters. Finally, we have successfully generated different amorphous layer thickness of the a-Si/c-Si and a-Si:H/c-Si 5 nm nanowires from heat and quench. We perform structural analysis of the a-Si-/c-Si nanowires. The RDF, Si-Si bond length distributions, and the coordination number distributions of amorphous regions of the nanowires reproduce similar behaviour compared to bulk amorphous silicon. In the final part of this thesis we examine different surface terminating chemical groups, -H, - OH and –NH2 in (001) GeNW. Our work shows that the diameter of Ge nanowires and the nature of surface terminating groups both play a significant role in both the magnitude and the nature of the nanowire band gaps, allowing tuning of the band gap by up to 1.1 eV. We also show for the first time how the nanowire diameter and surface termination shifts the absorption edge in the Ge nanowires to longer wavelengths. Thus, the combination of nanowire diameter and surface chemistry can be effectively utilised to tune the band gaps and thus light absorption properties of small diameter Ge nanowires.

A microscopic study of structural and electronic properties of functionalized silicon surfaces based on first-principles

Surface modification of silicon with organic monolayers tethered to the surface by different linkers is an important process in realizing future (opto-)electronic devices. Understanding the role played by the nature of the linking group and the chain length on the adsorption structures and electronic properties of these assemblies is vital to advance this technology. This Thesis is a study of such properties and contributes in particular to a microscopic understanding of induced changes in the work function of experimentally studied functionalized silicon surfaces. Using first-principles density functional theory (DFT), at the first step, we provide predictions for chemical trends in the work function of hydrogenated silicon (111) surfaces modified with various terminations. For nonpolar terminating atomic species such as F, Cl, Br, and I, the change in the work function is directly proportional to the amount of charge transferred from the surface, thus relating to the difference in electronegativity of the adsorbate and silicon atoms. The change is a monotonic function of coverage in this case, and the work function increases with increasing electronegativity. Polar species such as −TeH, −SeH, −SH, −OH, −NH2, −CH3, and −BH2 do not follow this trend due to the interaction of their dipole with the induced electric field at the surface. In this case, the magnitude and sign of the surface dipole moment need to be considered in addition to the bond dipole to generally describe the change in work function. Compared to hydrogenated surfaces, there is slight increase in the work function of H:Si(111)-XH, where X = Te, Se, and S, whereas reduction is observed for surfaces covered with −OH, −CH3, and −NH2. Next, we study the hydrogen passivated Si(111) surface modified with alkyl chains of the general formula H:Si–(CH2)n–CH2 and H:Si–X–(CH2)n–CH3, where X = NH, O, S and n = (0, 1, 3, 5, 7, 9, 11), at half coverage. For (X)–Hexyl and (X)–Dodecyl functionalization, we also examined various coverages up to full monolayer grafting in order to validate the result of half covered surface and the linker effect on the coverage. We find that it is necessary to take into account the van der Waals interaction between the alkyl chains. The strongest binding is for the oxygen linker, followed by S, N, and C, irrespective of chain length. The result revealed that the sequence of the stability is independent of coverage; however, linkers other than carbon can shift the optimum coverage considerably and allow further packing density. For all linkers apart from sulfur, structural properties, in particular, surface-linker-chain angles, saturate to a single value once n > 3. For sulfur, we identify three regimes, namely, n = 0–3, n = 5–7, and n = 9–11, each with its own characteristic adsorption structures. Where possible, our computational results are shown to be consistent with the available experimental data and show how the fundamental structural properties of modified Si surfaces can be controlled by the choice of linking group and chain length. Later we continue by examining the work function tuning of H:Si(111) over a range of 1.73 eV through adsorption of alkyl monolayers with general formula -[Xhead-group]-(CnH2n)-[Xtail-group], X = O(H), S(H), NH(2). The work function is practically converged at 4 carbons (8 for oxygen), for head-group functionalization. For tail-group functionalization and with both head- and tail-groups, there is an odd-even effect in the behavior of the work function, with peak-to-peak amplitudes of up to 1.7 eV in the oscillations. This behavior is explained through the orientation of the terminal-group's dipole. The shift in the work function is largest for NH2-linked and smallest for SH-linked chains and is rationalized in terms of interface dipoles. Our study reveals that the choice of the head- and/or tail-groups effectively changes the impact of the alkyl chain length on the work function tuning using self-assembled monolayers and this is an important advance in utilizing hybrid functionalized Si surfaces. Bringing together the understanding gained from studying single type functionalization of H:Si(111) with different alkyl chains and bearing in mind how to utilize head-group, tail-group or both as well as monolayer coverage, in the final part of this Thesis we study functionalized H:Si(111) with binary SAMs. Aiming at enhancing work function adjustment together with SAM stability and coverage we choose a range of terminations and linker-chains denoted as –X–(Alkyl) with X = CH3, O(H), S(H), NH(2) and investigate the stability and work function of various binary components grafted onto H:Si(111) surface. Using binary functionalization with -[NH(2)/O(H)/S(H)]-[Hexyl/Dodecyl] we show that work function can be tuned within the interval of 3.65-4.94 eV and furthermore, enhance the SAM’s stability. Although direct Si-C grafted SAMs are less favourable compared to their counterparts with O, N or S linkage, regardless of the ratio, binary functionalized alkyl monolayers with X-alkyl (X = NH, O) is always more stable than single type alkyl functionalization with the same coverage. Our results indicate that it is possible to go beyond the optimum coverage of pure alkyl functionalized SAMs (50%) by adding a linker with the correct choice of the linker. This is very important since dense packed monolayers have fewer defects and deliver higher efficiency. Our results indicate that binary anchoring can modify the charge injection and therefore bond stability while preserving the interface electronic structure.

Canon Ulick Bourke: cultural nationalism, popular politics and the Knock apparition

Accounts of the Knock Apparition, academic and devotional, always start by relating that the Virgin Mary, St Joseph, and St John the Evangelist appeared to fifteen people on a rainy Thursday evening at the south gable of Knock chapel, Co. Mayo, on 21 August 1879. They usually mention that the Land War was in progress. Despite the fact Knock supposedly receives one and a half million visitors a year, until three decades ago no scholar had examined accounts of the apparition. Recent work has sought to define the Knock Apparition in light of the Land War, the ‘devotional revolution’, which took place in Irish Catholicism in the quarter century prior to the apparition, and the influence of the parish priest, Archdeacon Bartholomew Cavanagh. This thesis acknowledges these factors, but contends that the single greatest force in shaping accounts of the apparition was Canon Ulick Joseph Bourke, one of the three priests on the commission of investigation into Knock. Furthermore, this thesis proves that Bourke’s role as a central figure in influencing the later Gaelic revival has been overlooked by scholars of cultural nationalism. By examining Bourke’s cultural nationalism and views on antiquity and language, as well as his politics and reaction to the Land War, this thesis argues that Bourke sought to create an orthodox version of the apparition which could be reconciled to his views on Irish Catholic identity, while serving as a bulwark against threats to the temporal power of the clergy. In addition to influencing accounts of the apparition through his role in interviewing the witnesses and recording their testimony, Bourke further shaped the narrative of the apparition by controlling its dissemination, to the extent that all accounts of Knock are based on a text largely created by him.

A highly efficient sensor platform using simply manufactured nanodot patterned substrates

Block copolymer (BCP) self-assembly is a low-cost means to nanopattern surfaces. Here, we use these nanopatterns to directly print arrays of nanodots onto a conducting substrate (Indium Tin Oxide (ITO) coated glass) for application as an electrochemical sensor for ethanol (EtOH) and hydrogen peroxide (H

Surrealism in Belgium during the inter-war period

info:eu-repo/semantics/published

Risk communication in clinical trials: a cognitive experiment and a survey.

BACKGROUND: A Royal Statistical Society Working Party recently recommended that "Greater use should be made of numerical, as opposed to verbal, descriptions of risk" in first-in-man clinical trials. This echoed the view of many clinicians and psychologists about risk communication. As the clinical trial industry expands rapidly across the globe, it is important to understand risk communication in Asian countries. METHODS: We conducted a cognitive experiment about participation in a hypothetical clinical trial of a pain relief medication and a survey in cancer and arthritis patients in Singapore. In part 1 of the experiment, the patients received information about the risk of side effects in one of three formats (frequency, percentage and verbal descriptor) and in one of two sequences (from least to most severe and from most to least severe), and were asked about their willingness to participate. In part 2, the patients received information about the risk in all three formats, in the same sequence, and were again asked about their willingness to participate. A survey of preference for risk presentation methods and usage of verbal descriptors immediately followed. RESULTS: Willingness to participate and the likelihood of changing one's decision were not affected by the risk presentation methods. Most patients indicated a preference for the frequency format, but patients with primary school or no formal education were indifferent. While the patients used the verbal descriptors "very common", "common" and "very rare" in ways similar to the European Commission's Guidelines, their usage of the descriptors "uncommon" and "rare" was substantially different from the EU's. CONCLUSION: In this sample of Asian cancer and arthritis patients, risk presentation format had no impact on willingness to participate in a clinical trial. However, there is a clear preference for the frequency format. The lay use of verbal descriptors was substantially different from the EU's.

Shifting Loyalties: World War I and the Conflicted Politics of Patriotism in the British Caribbean

This dissertation examines how the crisis of World War I impacted imperial policy and popular claims-making in the British Caribbean. Between 1915 and 1918, tens of thousands of men from the British Caribbean volunteered to fight in World War I and nearly 16,000 men, hailing from every British colony in the region, served in the newly formed British West Indies Regiment (BWIR). Rousing appeals to imperial patriotism and manly duty during the wartime recruitment campaigns and postwar commemoration movement linked the British Empire, civilization, and Christianity while simultaneously promoting new roles for women vis-à-vis the colonial state. In Jamaica and Trinidad and Tobago, the two colonies that contributed over seventy-five percent of the British Caribbean troops, discussions about the meaning of the war for black, coloured, white, East Indian, and Chinese residents sparked heated debates about the relationship among race, gender, and imperial loyalty.

To explore these debates, this dissertation foregrounds the social, cultural, and political practices of BWIR soldiers, tracing their engagements with colonial authorities, military officials, and West Indian civilians throughout the war years. It begins by reassessing the origins of the BWIR, and then analyzes the regional campaign to recruit West Indian men for military service. Travelling with newly enlisted volunteers across the Atlantic, this study then chronicles soldiers' multi-sited campaign for equal status, pay, and standing in the British imperial armed forces. It closes by offering new perspectives on the dramatic postwar protests by BWIR soldiers in Italy in 1918 and British Honduras and Trinidad in 1919, and reflects on the trajectory of veterans' activism in the postwar era.

This study argues that the racism and discrimination soldiers experienced overseas fueled heightened claims-making in the postwar era. In the aftermath of the war, veterans mobilized collectively to garner financial support and social recognition from colonial officials. Rather than withdrawing their allegiance from the empire, ex-servicemen and civilians invoked notions of mutual obligation to argue that British officials owed a debt to West Indians for their wartime sacrifices. This study reveals the continued salience of imperial patriotism, even as veterans and their civilian allies invoked nested local, regional, and diasporic loyalties as well. In doing so, it contributes to the literature on the origins of patriotism in the colonial Caribbean, while providing a historical case study for contemporary debates about "hegemonic dissolution" and popular mobilization in the region.

This dissertation draws upon a wide range of written and visual sources, including archival materials, war recruitment posters, newspapers, oral histories, photographs, and memoirs. In addition to Colonial Office records and military files, it incorporates previously untapped letters and petitions from the Jamaica Archives, National Archives of Trinidad and Tobago, Barbados Department of Archives, and US National Archives.

Archaeological Excavations at 18AP14: The Victualling Warehouse Site, 77 Main Street, Annapolis, Maryland, 1982 - 1984

The Victualling Warehouse Site, located at 77 Main Street in Annapolis, Maryland, was excavated by Archaeology in Annapolis during the summers of 1982 and 1983 and the fall of 1984. Funding was provided by Historic Annapolis, Incorporated (now Historic Annapolis Foundation), the University of Maryland, the Maryland Committee for the Humanities, and the Maryland Commission on the Capital City. This site has been used for commercial and residential purposes since the 1740's. During the Revolution the warehouses were used as a victualling office to supply American troops. A fire in 1970 destroyed these buildings and the present structure, also used as a store, was built about twenty years later. Over the three years of excavation, a total of 36 5 foot by 5 foot units were excavated revealing several features, including the foundations of one of the eighteenth century warehouses.

Peace and war: trajectories of posttraumatic stress disorder symptoms before, during, and after military deployment in Afghanistan.

In the study reported here, we examined posttraumatic stress disorder (PTSD) symptoms in 746 Danish soldiers measured on five occasions before, during, and after deployment to Afghanistan. Using latent class growth analysis, we identified six trajectories of change in PTSD symptoms. Two resilient trajectories had low levels across all five times, and a new-onset trajectory started low and showed a marked increase of PTSD symptoms. Three temporary-benefit trajectories, not previously described in the literature, showed decreases in PTSD symptoms during (or immediately after) deployment, followed by increases after return from deployment. Predeployment emotional problems and predeployment traumas, especially childhood adversities, were predictors for inclusion in the nonresilient trajectories, whereas deployment-related stress was not. These findings challenge standard views of PTSD in two ways. First, they show that factors other than immediately preceding stressors are critical for PTSD development, with childhood adversities being central. Second, they demonstrate that the development of PTSD symptoms shows heterogeneity, which indicates the need for multiple measurements to understand PTSD and identify people in need of treatment.