Simulation of Photovoltaic Panel Production as Complement to Ground Source Heat Pump System

This master thesis presents a new technological combination of two environmentally friendly sources of energy in order to provide DHW, and space heating. Solar energy is used for space heating, and DHW production using PV modules which supply direct current directly to electrical heating elements inside a water storage tank. On the other hand a GSHP system as another source of renewable energy provides heat in the water storage tank of the system in order to provide DHW and space heating. These two sources of renewable energy have been combined in this case-study in order to obtain a more efficient system, which will reduce the amount of electricity consumed by the GSHP system.The key aim of this study is to make simulations, and calculations of the amount ofelectrical energy that can be expected to be produced by a certain amount of PV modules that are already assembled on a house in Vantaa, southern Finland. This energy is then intended to be used as a complement to produce hot water in the heating system of the house beside the original GSHP system. Thus the amount of electrical energy purchased from the grid should be reduced and the compressor in the GSHP would need fewer starts which would reduce the heating cost of the GSHP system for space heating and providing hot water.The produced energy by the PV arrays in three different circuits will be charged directly to three electrical heating elements in the water storage tank of the existing system to satisfy the demand of the heating elements. The excess energy can be used to heat the water in the water storage tank to some extent which leads to a reduction of electricity consumption by the different components of the GSHP system.To increase the efficiency of the existing hybrid system, optimization of different PV configurations have been accomplished, and the results are compared. Optimization of the arrays in southern and western walls shows a DC power increase of 298 kWh/year compared with the existing PV configurations. Comparing the results from the optimization of the arrays on the western roof if the intention is to feed AC power to the components of the GSHP system shows a yearly AC power production of 1,646 kWh.This is with the consideration of no overproduction by the PV modules during the summer months. This means the optimized PV systems will be able to cover a larger part of summer demand compared with the existing system.

System Integration of PV/T Collectors in Solar Cooling Systems

The demand for cooling and air-conditioning of building is increasingly ever growing. This increase is mostly due to population and economic growth in developing countries, and also desire for a higher quality of thermal comfort. Increase in the use of conventional cooling systems results in larger carbon footprint and more greenhouse gases considering their higher electricity consumption, and it occasionally creates peaks in electricity demand from power supply grid. Solar energy as a renewable energy source is an alternative to drive the cooling machines since the cooling load is generally high when solar radiation is high. This thesis examines the performance of PV/T solar collector manufactured by Solarus company in a solar cooling system for an office building in Dubai, New Delhi, Los Angeles and Cape Town. The study is carried out by analyzing climate data and the requirements for thermal comfort in office buildings. Cooling systems strongly depend on weather conditions and local climate. Cooling load of buildings depend on many parameters such as ambient temperature, indoor comfort temperature, solar gain to the building and internal gains including; number of occupant and electrical devices. The simulations were carried out by selecting a suitable thermally driven chiller and modeling it with PV/T solar collector in Polysun software. Fractional primary energy saving and solar fraction were introduced as key figures of the project to evaluate the performance of cooling system. Several parametric studies and simulations were determined according to PV/T aperture area and hot water storage tank volume. The fractional primary energy saving analysis revealed that thermally driven chillers, particularly adsorption chillers are not suitable to be utilizing in small size of solar cooling systems in hot and tropic climates such as Dubai and New Delhi. Adsorption chillers require more thermal energy to meet the cooling load in hot and dry climates. The adsorption chillers operate in their full capacity and in higher coefficient of performance when they run in a moderate climate since they can properly reject the exhaust heat. The simulation results also indicated that PV/T solar collector have higher efficiency in warmer climates, however it requires a larger size of PV/T collectors to supply the thermally driven chillers for providing cooling in hot climates. Therefore using an electrical chiller as backup gives much better results in terms of primary energy savings, since PV/T electrical production also can be used for backup electrical chiller in a net metering mechanism.

Competitividade dos biocombustíveis no Brasil: uma comparação entre os principais biocombustíveis etanol e biodisel

As preocupações mundiais com o aquecimento global e os efeitos nocivos da utilização de combustíveis fósseis têm fomentado a busca por novos modelos energéticos, baseados em fontes limpas e renováveis, com destaque para os biocombustíveis. Sem menos importância, o esgotamento das reservas mundiais de matérias-primas fósseis, somado às instabilidades geopolíticas nas principais regiões produtoras, impulsionam, cada vez mais, o desenvolvimento destes novos modelos. Neste cenário, o Brasil tem papel de destaque. Líder mundial na produção e consumo de etanol à base de cana-de-açúcar, o país iniciou, em 2005, a inclusão de mais uma fonte de energia renovável em sua matriz energética: a mistura do biodiesel no diesel mineral. O presente trabalho tem como objetivo analisar a competitividade dos principais biocombustíveis brasileiros: o etanol e o biodiesel. Em primeiro lugar, estes produtos foram analisados quanto às suas principais características; em segundo, avaliou-se a competitividade econômica destes combustíveis frente a seus produtos substitutos diretos derivados do petróleo. Finalmente, foram analisados os benefícios (tangíveis e intangíveis) inerentes à utilização dos biocombustíveis, e como estes intangíveis deveriam ser precificados, como forma de atribuir um prêmio aos benefícios que trazem ao meio-ambiente e à sociedade. Esta dissertação pretende servir de base para uma avaliação mais profunda da real competitividade econômica dos biocombustíveis frente aos combustíveis derivados do petróleo, além de colocar em cheque as principais análises atuais e críticas sobre a utilização destes produtos. Além disso, o presente trabalho visa avaliar o potencial e as limitações da produção dos biocombustíveis no Brasil.

A reestruturação do setor sucroenergético no Brasil: uma análise do período entre 2005 e 2011

O mundo está diante do desafio de reduzir as emissões de gases do efeito estufa (GEEs) e encontrar fontes renováveis de energia, na busca da segurança energética. Os biocombustíveis são uma alternativa viável e, nesse sentido, o Brasil deu um exemplo para mundo ao criar o Proálcool em 1975, que foi um programa bem sucedido de substituição da gasolina pelo etanol produzido a partir da cana-de-açúcar. Essa iniciativa contou com a participação do Governo Brasileiro no incentivo e na regulamentação do setor sucroenergético. A partir da sua liberalização em 1999, a indústria canavieira passou por uma importante reestruturação. Este estudo teve como objetivo descrever esse movimento e analisar suas possíveis consequências para o setor. Para isso, foi realizada uma pesquisa sobre a reestruturação da indústria canavieira, entre 1999 e 2011, dando ênfase aos dois ciclos de operações de Fusões & Aquisições ocorridos nesse período. Como principais resultados têm-se a consolidação dos maiores grupos de usinas da Região Centro Sul, que aumentaram a sua participação na moagem de cana e ampliaram suas estruturas produtivas por meio da aquisição de usinas concorrentes e da construção de greenfields. Além disso, foi possível observar o rápido crescimento da participação do capital estrangeiro, juntamente com a entrada de grupos de outros setores industriais. A reestruturação terá consequências positivas para o Brasil, principalmente pela profissionalização do setor sucroenergético e pela capacidade de retomar o ritmo de crescimento da produção de cana-de-açúcar, que foi interrompido pela crise financeira mundial de 2008. Para isso, será necessário investir na ampliação dos canaviais e também na construção de novas usinas.

Pellets de madeira e sua viabilidade econômico-financeira na substituição do óleo BPF-A1 em pequenos e médios consumidores no Estado de São Paulo

A utilização de pellets de madeira é bastante difundida nos países desenvolvidos, em particular na Europa, e apresenta demanda crescente para a produção de energia elétrica e térmica, incluindo a calefação residencial. O Brasil apresenta capacidade indiscutível para a geração de diferentes biomassas e em quantidades expressivas, dada à vantagem competitiva de suas condições edafo-climáticas, sua extensão territorial e de ter baixos custos de produção. Apontar-se-á neste trabalho as condições mercadológicas, logísticas, normativas, de incentivos fiscais e de ambiente econômico, com as quais o país poderá se consolidar como um grande produtor e consumidor desta fonte de energia limpa e renovável. Este estudo apresenta as melhores técnicas conhecidas para a venda a pequenos e médios consumidores e para a produção, eficiente e com escala, de pellets de madeira, dentro do Estado de São Paulo. É discutida a necessidade de se ter florestas plantadas com o único propósito de serem transformadas em pellets. Nos últimos anos, os preços dos resíduos de madeira subiram no mercado interno, praticamente os excluindo como fonte de matéria-prima, num cenário de longo prazo. O objetivo final desta dissertação é apresentar os principais aspectos econômico-financeiros que influenciam os cenários para que os pellets de madeira possam substituir o óleo BPF-A1 no mercado regional, e assim discutindo se sua produção se mostrará atraente e confiável para potenciais investidores. Para a avaliação da viabilidade financeira, são utilizados os métodos-chave, Payback, Valor Presente Líquido e Taxa Interna de Retorno, e uma análise de sensibilidade das principais variáveis identificadas. Os principais resultados revelam um Payback de 47 meses, um NPV de R$10.942.127 e uma IRR de 25,18% a.a. em termos reais, para o cenário-base, além de identificar o preço da matéria-prima e a escala de produção como as variáveis mais sensíveis.

Patentes e etanol lignocelulósico

Produção intelectual e desenvolvimento tecnológico podem diferenciar países e regiões no processo de desenvolvimento socioeconômico. No caso do Brasil, observa-se o papel energético do etanol combustível para veículos motorizados leves como um resultado importante do avanço tecnológico do país, que vai além da aptidão agroclimática. A contínua busca pela especialização tecnológica verticalizada do setor sucroenergético poderia levar o Brasil a uma posição, se não autônoma, mais confortável, não só de produtor de matéria-prima, mas de processos agregadores de valor no que diz respeito aos processos de produção de etanol de segunda geração, produzido a partir de biomassa lignocelulósica. O objetivo desta dissertação é analisar os esforços de P&D que resultaram em Depósitos e Publicações de patentes em órgãos oficiais como o United States Patent and Trademark Office (USPTO), o European Patent Office (EPO), e o Instituto Nacional de Propriedade Industrial (INPI), no tema etanol de segunda geração. Ainda, verifica-se se esses esforços impactam no poder concorrencial de países e firmas depositantes de patentes. Além das coletas e observações dos dados dos órgãos acima mencionados, foram calculados para os dados de depósitos e publicações de patentes no tema bioetanol lignocelulósico os índices de Herfindahl Hirschman (HHI) e a razão de concentração (Concentration Ratio) CR4, tradicionalmente utilizados para que órgãos reguladores de defesa do consumidor autorizem fusões e aquisições entre participantes de um determinado mercado. Esse método permite a observação do grau de competitividade entre as firmas depositantes de patentes no tema e a possível tendência sobre a detenção do controle em futuro próximo e a corrida para venda de royalties dos processos desenvolvidos em diferentes áreas tecnológicas para incrementar a produção industrial de etanol avançado. Os resultados indicam uma concentração elevada dos esforços de pesquisa, medidos pelos depósitos de patentes, referentes a etanol de segunda geração, em um número muito reduzido de empresas norte-americanas, quando analisada a base de dados dos EUA. O sucesso desses esforços, mensurados pela publicação de patentes, contudo, não se mostra concentrado nem nos EUA nem na União Europeia. No caso do Brasil, ainda não são encontradas publicações de patentes no tema Lignocellulosic Bioethanol, bem como apenas uma empresa brasileira possui uma patente publicada nos Estados Unidos. Esses resultados sugerem que investimentos em pesquisa científica no Brasil podem produzir mais artigos publicados e titulação acadêmica/científica que propriamente o registro de patentes em órgãos especializados em qualificar a invenção de métodos, processos ou fórmulas, dentro e fora do país. Isso pode significar tanto baixo esforço em pesquisa no assunto quanto à perda pelo autor e/ou sua instituição da oportunidade de ter seu esforço de pesquisa recompensado por meio de royalties, como compensação pela criatividade, dedicação intelectual e de recursos econômicos. Os resultados deste estudo contribuem para o debate a respeito da crescente necessidade de produção e abastecimento de fontes renováveis de energia, como o biocombustível etanol avançado à base do derivado bagaço de cana-de-açúcar, a custos mais competitivos como matéria-prima adicional e para produção incremental de etanol em futuro próximo. As conclusões do estudo indicam a necessidade do aumento na produção de conhecimento aplicado e em esforços para garantir sua propriedade intelectual, permitindo o retorno patrimonial com royalties.

The Brazilian financial system and the green economy : alignment with sustainable development

Three studies were prepared and are presented in this document. The first, The Brazilian Financial Sector Institutional Context in the Transition to Sustainable Development looks at the legislation, regulation, and public policies aimed at socio-environmental themes related to the financial sector. The second study, Current Financing for the Green Economy in Brazil, provides an initial estimate of the financial assets already allocated to the green economy, as well as a methodological proposal for the survey and monitoring of the respective flow of assets. The third and final study looks at two important segments of the Brazilian economy and their process of transition to a greener economy: renewable energy and agriculture.

Precificação de energia eólica offshore no Brasil

Offshore wind power emits low amounts of gases, is renewable and has better performance than onshore due to its greater stability and higher wind power density, less visual and noise impact, among others. Brazil has a high capacity of generation, but has not yet developed any offshore projects. High costs are a strong impediment. This study is an effort towards pricing offshore resources through Livelized Cost of Energy - LCOE, which represents the minimum return to cover the costs of development, production and maintenance of a wind project. Initially LCOE was calculated for all Brazilian onshore wind farms listed at Bloomberg New Energy Finance R○, accounting for 71 farms. Then hypothetical offshore wind farms were created from the onshore farms, tripling the cost of generation, which is consistent with the literature, and estimating the offshore energy for two locations off the Brazilian coast using satellite data extracted from National Oceanic and Atmospheric Administration. The results demonstrate that offshore resources have the potential to significantly reduce the energy price due to the better performance of the wind at sea

Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Análise de um queimador infravermelho funcionando com combustível híbrido : GLP/Bio-óleo

Biomass is considered the largest renewable energy source that can be used in an environmentally sustainable. From the pyrolysis of biomass is possible to obtain products with higher energy density and better use properties. The liquid resultant of this process is traditionally called bio-oil. The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with a greater control of emissions due to the passage of exhaust gases through a macroporous ceramic bed. This paper presents a commercial infrared burner adapted with an ejector proposed able to burn a hybrid configuration of liquefied petroleum gas (LPG) and bio-oil diluted. The dilution of bio-oil with absolute ethanol aimed to decrease the viscosity of the fluid, and improving the stability and atomization. It was introduced a temperature controller with thermocouple modulating two stages (low heat / high heat), and solenoid valves for fuels supply. The infrared burner has been tested, being the diluted bio-oil atomized, and evaluated its performance by conducting energy balance. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by thermocouples. The dilution reduced the viscosity of the bio-oil in 75.4% and increased by 11% the lower heating value (LHV) of the same, providing a stable combustion to the burner through the atomizing with compressed air and burns combined with LPG. Injecting the hybrid fuel there was increase in the heat transfer from the plate to the environment in 21.6% and gain useful benefit of 26.7%, due to the improved in the efficiency of the 1st Law of Thermodynamics of infrared burner

Desenvolvimento de uma unidade pirolítica com reator de cilindro rotativo: obtenção de bio-óleo

The demand for alternative sources of energy drives the technological development so that many fuels and energy conversion processes before judged as inadequate or even non-viable, are now competing fuels and so-called traditional processes. Thus, biomass plays an important role and is considered one of the sources of renewable energy most important of our planet. Biomass accounts for 29.2% of all renewable energy sources. The share of biomass energy from Brazil in the OIE is 13.6%, well above the world average of participation. Various types of pyrolysis processes have been studied in recent years, highlighting the process of fast pyrolysis of biomass to obtain bio-oil. The continuous fast pyrolysis, the most investigated and improved are the fluidized bed and ablative, but is being studied and developed other types in order to obtain Bio-oil a better quality, higher productivity, lower energy consumption, increased stability and process reliability and lower production cost. The stability of the product bio-oil is fundamental to designing consumer devices such as burners, engines and turbines. This study was motivated to produce Bio-oil, through the conversion of plant biomass or the use of its industrial and agricultural waste, presenting an alternative proposal for thermochemical pyrolysis process, taking advantage of particle dynamics in the rotating bed that favors the right gas-solid contact and heat transfer and mass. The pyrolyser designed to operate in a continuous process, a feeder containing two stages, a divisive system of biomass integrated with a tab of coal fines and a system of condensing steam pyrolytic. The prototype has been tested with sawdust, using a complete experimental design on two levels to investigate the sensitivity of factors: the process temperature, gas flow drag and spin speed compared to the mass yield of bio-oil. The best result was obtained in the condition of 570 oC, 25 Hz and 200 cm3/min, temperature being the parameter of greatest significance. The mass balance of the elementary stages presented in the order of 20% and 37% liquid pyrolytic carbon. We determined the properties of liquid and solid products of pyrolysis as density, viscosity, pH, PCI, and the composition characterized by chemical analysis, revealing the composition and properties of a Bio-oil.

O Papel do Estado na promoção do Desenvolvimento Nacional: a utilização do instrumento do planejamento na expansão da oferta energética

The progress of a nation is closely linked to the energy supply that it has to develop its economic capabilities. The dependence of contemporary society for energy requires the continued expansion of the use of renewable energy, and implies coordinated action of the Democratic State in the delimitation of the best ways to make full use of energy. In periods of rapid development, countries need an increment of energy supplies superior to those of periods of regular economic growth. Energy demand generated by the condition of Brazil as an emerging country reveals the need for orderly expansion of energy supply. In reverse, lack of energy planning effectively paralyzes a country and generates incalculable losses in national socioeconomic development. The Brazilian Constitution abandoned the notion of development tied to the simple increase in the gross domestic product. The respect for the environment, sovereignty, national development, and especially the constant and growing supply of energy, promotes the advancement of national economic agents, and quenches the simple accounting increase in energy supply. Constitutional principles condition the rational use of energy potentials, in ensuring adequate supply of energy for the entire national territory. The Brazilian Ministry of Mines and Energy, through its agencies, government offices and companies, establishes and formulates policies and guidelines for energy in Brazil, playing an important role in national energy planning. National development is enhanced by the good performance of the state agencies responsible for planning the energy sector

Proposta de localização de uma unidade de tratamento de óleo e gordura residual de fritura na cidade do Natal/RN para produção de biodiesel

This work addresses biodiesel by transesterification from the use of waste frying oil as a possible technological alternative for both reducing greenhouse gas emissions and by presenting themselves as an environmental call to designate a rational use of oil when no longer played in the environment to become renewable energy. It has proposed location of a residual oil and fat treatment plant to produce biodiesel, using models of Location and Routing for the improvement of routes. To achieve the goal, questionnaires were administered in establishments that use oil or vegetable fat in their productive activities in order to quantify the residue, to analyze actions and environmental perception of people who work directly with the residue on the destination you are being given to oil and fat used. It has indicated using of two single setup location, the method of Center of Gravity and the model of Ardalan, a geographical point that minimizes the costs of transporting waste to the treatment plant. Actions have been proposed for the improvement of collection routes this residue using the Routing Method of Scanning, as an illustration. The results demonstrated the lack of knowledge of the people who deal directly with large amounts of waste, on the environmental impacts caused by their incorrect disposal. The models used were uniform since point out to neighborhoods in similar regions. The neighborhoods of Lagoa Nova / Morro Branco (Ardalan) and Nova Descoberta (Center of Gravity) as ideal for the installation of treatment plant. However, it is suggested to be tested other models that take into account new variables than those used (supply of waste and the distance between points). The routing through the method of scanning has shown that it is possible, in a simple way to optimize routes in order to reduce distances and therefore the logistics costs in the collection of such waste. Introducing a route as a test to gather the twenty largest oil suppliers used in sample frying, using as a main factor time 8 hour of working shift every day