LPG Gas-Sensing System With SnO2 Thin-Film Transducer and 0.7-mu m CMOS Signal Conditioning ASIC

The design and implementation of a complete gas sensor system for liquified petroleum gas (LPG) gas sensing are presented. The system consists of a SnO2 transducer, a lowcost heater, an application specific integrated circuit (ASIC) with front-end interface circuitry, and a microcontroller interface for data logging. The ASIC includes a relaxation-oscillator-based heater driver circuit that is capable of controlling the sensor operating temperature from 100degC to 425degC. The sensor readout circuit in the ASIC, which is based on the resistance to time conversion technique, has been designed to measure the gas sensor response over three orders of resistance change during its interaction with gases.

Studies On Hydrogen Bonds: Part IV. Proposed Working Criteria for Assessing Qualitative Strength of Hydrogen Bonds

The data obtained in the earlier parts of this series for the donor and acceptor end parameters of N-H. O and O-H. O hydrogen bonds have been utilised to obtain a qualitative working criterion to classify the hydrogen bonds into three categories: "very good" (VG), "moderately good" (MG) and weak (W). The general distribution curves for all the four parameters are found to be nearly of the Gaussian type. Assuming that the VG hydrogen bonds lie between 0 and ± la, MG hydrogen bonds between ± 1 and ± 2, W hydrogen bonds beyond ± 2 (where is the standard deviation), suitable cut-off limits for classifying the hydrogen bonds in the three categories have been derived. These limits are used to get VG and MG ranges for the four parameters 1 and θ (at the donor end) and ± and ± (at the acceptor end). The qualitative strength of a hydrogen bond is decided by the cumulative application of the criteria to all the four parameters. The criterion has been further applied to some practical examples in conformational studies such as α-helix and can be used for obtaining suitable location of hydrogen atoms to form good hydrogen bonds. An empirical approach to the energy of hydrogen bonds in the three categories has also been presented.

Account of monies received for offerings

Digital image

Bills received and collected of Mr. Lazarus

Digital image

Influence of Joint Thickness and Mortar-Block Elastic Properties on the Strength and Stresses Developed in Soil-Cement Block Masonry

Soil-cement blocks are employed for load bearing masonry buildings. This paper deals with the study on the influence of bed joint thickness and elastic properties of the soil-cement blocks, and the mortar on the strength and behavior of soil-cement block masonry prisms. Influence of joint thickness on compressive strength has been examined through an experimental program. The nature of stresses developed and their distribution, in the block and the mortar of the soil-cement block masonry prism under compression, has been analyzed by an elastic analysis using FEM. Influence of various parameters like joint thickness, ratio of block to mortar modulus, and Poisson's ratio of the block and the mortar are considered in FEM analysis. Some of the major conclusions of the study are: (1) masonry compressive strength is sensitive to the ratio of modulus of block to that of the mortar (Eb/Em) and masonry compressive strength decreases as the mortar joint thickness is increased for the case where the ratio of block to mortar modulus is more than 1; (2) the lateral tensile stresses developed in the masonry unit are sensitive to the Eb/Em ratio and the Poisson's ratio of mortar and the masonry unit; and (3) lateral stresses developed in the masonry unit are more sensitive to the Poisson's ratio of the mortar than the Poisson's ratio of the masonry unit.

Insights into students' conceptual understanding using textual analysis: A case study in signal processing

Concept inventory tests are one method to evaluate conceptual understanding and identify possible misconceptions. The multiple-choice question format, offering a choice between a correct selection and common misconceptions, can provide an assessment of students' conceptual understanding in various dimensions. Misconceptions of some engineering concepts exist due to a lack of mental frameworks, or schemas, for these types of concepts or conceptual areas. This study incorporated an open textual response component in a multiple-choice concept inventory test to capture written explanations of students' selections. The study's goal was to identify, through text analysis of student responses, the types and categorizations of concepts in these explanations that had not been uncovered by the distractor selections. The analysis of the textual explanations of a subset of the discrete-time signals and systems concept inventory questions revealed that students have difficulty conceptually explaining several dimensions of signal processing. This contributed to their inability to provide a clear explanation of the underlying concepts, such as mathematical concepts. The methods used in this study evaluate students' understanding of signals and systems concepts through their ability to express understanding in written text. This may present a bias for students with strong written communication skills. This study presents a framework for extracting and identifying the types of concepts students use to express their reasoning when answering conceptual questions.

Wrought aluminum-nickel alloys for high strength-high conductivity applications

Aluminum-Nickel alloys ranging from 0.06 pct to 6.1 pct (by wt) Ni have been developed for high strength-high conductivity applications. These alloys were produced by solidification in a permanent mold followed by homogenization, hot extrusion or hot rolling and cold drawing to wire form. This sequence of fabrication a) led to the production of fine fibrous dispersoids of NiAl3 as part of the Al-NiAl3 eutectic during the initial casting operation, b) permitted the retention of fine fibrous dispersiods of NiAl3 produced during casting without any significant coarsening during processing and c) led to uniform dispersion and general alignment of these fibrous dispersoids along a given direction in the product without any measurable fiber-matrix separation, extensive fiber-fragmentation or crack production in the matrix. These alloys can be processed to wire form as easily as aluminum and when processed by the above sequence, possess very attractive combination of high strength-high electrical conductivity. Tensile strengths range from 173 N/mm2 (at 0.6 pct Ni) to 241 N/mm2 (at 6.1 pct Ni) in combination with corresponding conductivity values between 62 pct IACS and 55.5 pct IACS. The wires also possess attractive yield strength; for instance, the 0.2 pct off-set strength of Al-6.1 pct Ni wire is 213 N/mm2. Using simple composite rules, the estimated strength and the conductivity of NiAl3 fibers were found to be 1380 N/mm2 and 18 pct IACS respectively, in these wires.

Robust and High-resolution Voiced/Unvoiced Classification in Noisy Speech Using A Signal Smoothness Criterion

We propose a novel technique for robust voiced/unvoiced segment detection in noisy speech, based on local polynomial regression. The local polynomial model is well-suited for voiced segments in speech. The unvoiced segments are noise-like and do not exhibit any smooth structure. This property of smoothness is used for devising a new metric called the variance ratio metric, which, after thresholding, indicates the voiced/unvoiced boundaries with 75% accuracy for 0dB global signal-to-noise ratio (SNR). A novelty of our algorithm is that it processes the signal continuously, sample-by-sample rather than frame-by-frame. Simulation results on TIMIT speech database (downsampled to 8kHz) for various SNRs are presented to illustrate the performance of the new algorithm. Results indicate that the algorithm is robust even in high noise levels.

Food intake, growth and social interactions of signal crayfish, Pacifastacus leniusculus (Dana)

The knowledge about the optimal rearing conditions, such as water temperature and quality, photoperiod and density, with the understanding of animal nutritional requirements forms the basis of economically stable aquaculture for freshwater crayfish. However, the shift from a natural environment to effective culture conditions induces several changes, not only at the population level, but also at the individual level. The social contacts between conspecifics increase with increasing animal density. The competition for limited resources (e.g. food, shelter, mates) is more severe with the presence of agonistic behaviour and may lead to unequal distribution of these. The objectives of this study were to: 1) study the distribution of a common food resource between communally reared signal crayfish (Pacifastacus leniusculus) and to assign potential feeding hierarchy on the basis of individual food intake measurements, 2) explore the possibilities of size distribution manipulations to affect population dynamics and food intake to improve growth and survival in culture and 3) study the effect of food ration and spatial distribution on food intake and to explore the effect of temperature and food ration on growth and body composition of freshwater crayfish. The feeding ranks between animals were assigned with a new method for individual food intake measurement of communally reared crayfish. This technique has a high feasibility and a great potential to be applied in crayfish aquaculture studies. In this study, signal crayfish showed high size-related variability in food consumption both among individuals within a group (inter-individual) and within individual day-to-day variation (intra-individual). Increased competition for food led to an unequal distribution of this resource and this may be a reason for large growth differences between animals. The consumption was significantly higher when reared individually in comparison with communal housing. These results suggest that communally housed crayfish form a feeding hierarchy and that the animal size is the major factor controlling the position in this hierarchy. The optimisation of the social environment ( social conditions ) was evaluated in this study as a new approach to crayfish aquaculture. The results showed that the absence of conspecifics (individual rearing vs. communal housing) affects growth rate, food intake and the proportion of injured animals, whereas size variation between animals influences the number and duration of agonistic encounters. In addition, animal size had a strong influence on the fighting success of signal crayfish reared in a social milieu with a wide size variation of conspecifics. Larger individuals initiated and won most of the competitions, which suggests size-based social hierarchy of P. leniusculus. This is further supported by the fact that the length and weight gain of smaller animals increased after size grading, maybe because of a better access to the food resource due to diminished social pressure. However, the high dominance index was not based on size under conditions of limited size variation, e.g. those characteristic of restocked natural populations and aquaculture, indicating the important role of behaviour on social hierarchy.

Pathogen-Induced Defense Signaling and Signal Crosstalk in Arabidopsis

Erwinia carotovora subsp. carotovora is a bacterial phytopathogen that causes soft rot in various agronomically important crop plants. A genetically specified resistance to E. carotovora has not been defined, and plant resistance to this pathogen is established through nonspecific activation of basal defense responses. This, together with the broad host range, makes this pathogen a good model for studying the activation of plant defenses. Production and secretion of plant cell wall-degrading enzymes (PCWDE) are central to the virulence of E. carotovora. It also possesses the type III secretion system (TTSS) utilized by many Gram-negative bacteria to secrete virulence- promoting effector proteins to plant cells. This study elucidated the role of E. carotovora HrpN (HrpNEcc), an effector protein secreted through TTSS, and the contribution of this protein in the virulence of E. carotovora. Treatment of plants with HrpNEcc was demonstrated to induce a hypersensitive response (HR) as well as resistance to E. carotovora. Resistance induced by HrpNEcc required both salicylic acid (SA)- and jasmonate/ethylene (JA/ET)-dependent defense signaling in Arabidopsis. Simultaneous treatment of Arabidopsis with HrpNEcc and PCWDE polygalacturonase PehA elicited accelerated and enhanced induction of defense genes but also increased production of superoxide and lesion formation. This demonstrates mutual amplification of defense signaling by these two virulence factors of E. carotovora. Identification of genes that are rapidly induced in response to a pathogen can provide novel information about the early events occurring in the plant defense response. CHLOROPHYLLASE 1 (AtCLH1) and EARLY RESPONSIVE TO DEHYDRATION 15 (ERD15) are both rapidly triggered by E. carotovora in Arabidopsis. Characterization of AtCLH1 encoding chlorophyll-degrading enzyme chlorophyllase indicated that it might have a role in chlorophyll degradation during plant tissue damage. Silencing of this gene resulted in increased accumulation of reactive oxygen species (ROS) in response to pathogen infection in a light-dependent manner. This led to enhanced SA-dependent defenses and resistance to E. carotovora. Moreover, crosstalk between different defense signaling pathways was observed; JA-dependent defenses and resistance to fungal pathogen Alternaria brassicicola were impaired, indicating antagonism between SA- and JA-dependent signaling. Characterization of ERD15 suggested that it is a novel, negative regulator of abscisic acid (ABA) signaling in Arabidopsis. Overexpression of ERD15 resulted in insensitivity to ABA and reduced tolerance of the plants to dehydration stress. However, simultaneously, the resistance of the plants to E. carotovora was enhanced. Silencing of ERD15 improved freezing and drought tolerance of transgenic plants. This, together with the reducing effect of ABA on seed germination, indicated hypersensitivity to this phytohormone. ERD15 was hypothesized to act as a capacitor that controls the appropriate activation of ABA responses in Arabidopsis.

Flexural Strength of Modified Square Footings

The ultimate flexural strength behavior of isolated square tapered and beam-slab reinforced footings are presented. Yield line solutions are developed for generalized contact pressure distributions and the influence of taper, beam size, fillet size, negative moment capacity, and contact pressure distribution on the collapse load is brought out. In beam-slab footings the optimum relative beam capacity required to make the beam rigid is indicated. Results of experimental investigations on footings resting on sand reveal that tapered (with isotropic as well as with alternative reinforcement patterns) and beam-slab footings exhibit superior structural behavior in terms of normalized first crack load, collapse load, relative rigidity, relative efficiency, and failure mechanism.

A Generalized Approach to Multiresolution Complex SAR Signal Processing

Multiresolution synthetic aperture radar (SAR) image formation has been proven to be beneficial in a variety of applications such as improved imaging and target detection as well as speckle reduction. SAR signal processing traditionally carried out in the Fourier domain has inherent limitations in the context of image formation at hierarchical scales. We present a generalized approach to the formation of multiresolution SAR images using biorthogonal shift-invariant discrete wavelet transform (SIDWT) in both range and azimuth directions. Particularly in azimuth, the inherent subband decomposition property of wavelet packet transform is introduced to produce multiscale complex matched filtering without involving any approximations. This generalized approach also includes the formulation of multilook processing within the discrete wavelet transform (DWT) paradigm. The efficiency of the algorithm in parallel form of execution to generate hierarchical scale SAR images is shown. Analytical results and sample imagery of diffuse backscatter are presented to validate the method.

Peroxidases in lignifying xylem of Norway spruce, Scots pine and silver birch

Lignin is a complex plant polymer synthesized through co-operation of multiple intracellular and extracellular enzymes. It is deposited to plant cell walls in cells where additional strength or stiffness are needed, such as in tracheary elements (TEs) in xylem, supporting sclerenchymal tissues and at the sites of wounding. Class III peroxidases (POXs) are secreted plant oxidoreductases with implications in many physiological processes such as the polymerization of lignin and suberin and auxin catabolism. POXs are able to oxidize various substrates in the presence of hydrogen peroxide, including lignin monomers, monolignols, thus enabling the monolignol polymerization to lignin by radical coupling. Trees produce large amounts of lignin in secondary xylem of stems, branches and roots. In this study, POXs of gymnosperm and angiosperm trees were studied in order to find POXs which are able to participate in lignin polymerization in developing secondary xylem i.e. are located at the site of lignin synthesis in tree stems and have the ability to oxidize monolignol substrates. Both in the gymnosperm species, Norway spruce and Scots pine, and in the angiosperm species silver birch the monolignol oxidizing POX activities originating from multiple POX isoforms were present in lignifying secondary xylem in stems during the period of annual growth. Most of the partially purified POXs from Norway spruce and silver birch xylem had highest oxidation rate with coniferyl alcohol, the main monomer in guaiacyl-lignin in conifers. The only exception was the most anionic POX fraction from silver birch, which clearly preferred sinapyl alcohol, the lignin monomer needed in the synthesis of syringyl-guaiacyl lignin in angiosperm trees. Three full-length pox cDNAs px1, px2 and px3 were cloned from the developing xylem of Norway spruce. It was shown that px1 and px2 are expressed in developing tracheids in spruce seedlings, whereas px3 transcripts were not detected suggesting low transcription level in young trees. The amino acid sequences of PX1, PX2 and PX3 were less than 60% identical to each other but showed up to 84% identity to other known POXs. They all begin with predicted N-terminal secretion signal (SS) peptides. PX2 and PX3 contained additional putative vacuolar localization determinants (VSDs) at C-terminus. Transient expression of EGFP-fusions of the SS- and VSD-peptides in tobacco protoplasts showed SS-peptides directed EGFP to secretion in tobacco cells, whereas only the PX2 C-terminal peptide seems to be a functional VSD. According to heterologous expression of px1 in Catharanthus roseus hairy roots, PX1 is a guaicol-oxidizing POX with isoelectric point (pI) approximately 10, similar to monolignol oxidizing POXs in protein extracts from Norway spruce lignifying xylem. Hence, PX1 has characteristics for participation to monolignol dehydrogenation in lignin synthesis, whereas the other two spruce POXs seem to have some other functions. Interesting topics in future include functional characterization of syringyl compound oxidizing POXs and components of POX activity regulation in trees.