Development and characterization of orally-disintegrating films for propolis delivery

This study aimed at evaluating the effect of different concentrations of hydrolyzed collagen (HC) on the properties of an orally disintegrating film containing propolis ethanol extract (PEE) as an active component. The films were evaluated in terms of total phenols, mechanical properties, solubility, contact angle, disintegration time, and microstructure. The films were prepared by casting with 2 g of protein mass (gelatin and HC), 30 g of sorbitol/100 g of protein mass, and 100 g of PEE/100 g of protein mass. HC was incorporated at concentrations of 0, 10, 20, and 30 g/100 g of protein mass. It was found that increased concentrations of HC reduced tensile strength and increased elongation; however, all films showed plastic behavior. An increase in solubility at 25 ºC, a reduction in the contact angle, and disintegration time were also observed. Thus, higher concentrations of collagen led to more hydrophilic and more soluble polymeric matrices that showed shorter dissolution time, favoring the use of these materials as carriers for active compounds to be delivered in the oral cavity.

Development and optimization of a HPLC-RI method for the determination of major sugars in apple juice and evaluation of the effect of the ripening stage

The sugars in apple juice prove its authenticity and its sensory and nutritional properties. The aim of this study was to develop and validate a simple analytical method using high performance liquid chromatography with refractive index detection (HPLC-RI) to determinate and quantify the sugars sucrose, D-glucose, D-fructose, and D-sorbitol polyol in apple juices, as well as to analyze the juices from the Fuji suprema and Lis Gala cultivars at three ripening stages. The analytical performance parameters evaluated indicated that the method was specific for the compounds analyzed, and the linearity of the calibration curves of sugars showed high correlation coefficients (close to 1.0). The limits of detection and quantification are consistent with recommendations available in the literature for this type of matrix. Sample preparation is simple and generates small amount of residues. Over 70% of the sugars were determined in the juices of apples at the pre-ripe stage, with an increase during senescence. This method is applicable for the determination of sugars in juices and evaluation of apple ripening.

Development and chemical and sensory characterization of pumpkin seed flour-based cereal bars

Pumpkin (Cucurbita maxima), popularly known as squash, is a widely grown vegetable in Brazil. In this study, pumpkin seed flours (PSF) with different granulometries were used: PSF 1 (medium granulometry) and PSF 2 (coarse granulometry) in the preparation of cereal bars (CB) with different combinations with brown oats. Five formulations were prepared: CB-1 (control - 25% brown oats and 0% PSF); CB-2 (12.5% PSF 1 and 12.5% brown oats); CB-3 (25% PSF 1 and 0% brown oats); CB-4 (12.5% PSF 2 and 12.5% brown oats); and CB-5 (25% PSF 2 and 0% brown oats). The acceptance test results were analyzed in a conventional preference mapping which indicated that the bars CB-2 and CB-5 received mostly the maximum hedonistic score. With the objective of developing a cereal bar replacing oats with PSF, the bars CB-2 and CB-5 were compared to the conventional bar CB-1. The cereal bars CB-2 and CB-5 showed an increase in crude protein (87.5% and 62.5%) and in dietary fiber (77% and 44%), respectively. These results allowed the classification of CB-2 and CB-5 as fiber sources; they can, therefore, be classified as light products according to the Brazilian legislation.

Development and evaluation of iron-rich meatloaves containing pork liver for schoolchildren

AbstractIron deficiency is a highly prevalent nutritional problem worldwide and it impacts on the cognitive development of children. Therefore, the aim of this research was to develop meatloaf with high iron content by using in their formulations pork liver. Meatloaves were prepared with additions of 9.98% and 13.31% (formulations A and B) of pork liver in order to meet 15% and 20% of the daily requirement of iron (10 mg/day) for children. Samples were evaluated regarding their physicochemical, microbiological and sensory characteristics. The results were subjected to Analysis of Variance (ANOVA) followed by Tukey test. Results of physicochemical analyses showed an increase in protein and mineral contents and a decrease in fat content. The iron and zinc contents were respectively 100.0% and 70.83% (formulation A) and 152.73% and 97.92% (formulation B) higher than that of the standard formulation. Regarding fat content, the reduction of 31.5% in formulation B makes it a light product. As for the microbiological aspect, all meatloaves were adequate for consumption. Regarding sensory analysis, all the attributes considered were not statistically different, but for purchase intention test formulation B was better accepted. Therefore, formulations A and B are good sources of iron and zinc.

The political role of the State in Cambridge theories of growth and distribution

In this paper we extend Kaldor’s Neo-Pasinetti theorem to the scope of budgetary interventions based on political orientations. First, we take into account a system of taxes and expenditures. Second, we introduce different reaction functions for public spending showing the political role of the State in Cambridge theory of distribution. It turns out that the validity of Kaldorian results depends on the political orientation adopted by government, which diminishes the range of application of the Neo-Pasinetti theorem.

Measuring software security from the design of software

The vast majority of our contemporary society owns a mobile phone, which has resulted in a dramatic rise in the amount of networked computers in recent years. Security issues in the computers have followed the same trend and nearly everyone is now affected by such issues. How could the situation be improved? For software engineers, an obvious answer is to build computer software with security in mind. A problem with building software with security is how to define secure software or how to measure security. This thesis divides the problem into three research questions. First, how can we measure the security of software? Second, what types of tools are available for measuring security? And finally, what do these tools reveal about the security of software? Measuring tools of these kind are commonly called metrics. This thesis is focused on the perspective of software engineers in the software design phase. Focus on the design phase means that code level semantics or programming language specifics are not discussed in this work. Organizational policy, management issues or software development process are also out of the scope. The first two research problems were studied using a literature review while the third was studied using a case study research. The target of the case study was a Java based email server called Apache James, which had details from its changelog and security issues available and the source code was accessible. The research revealed that there is a consensus in the terminology on software security. Security verification activities are commonly divided into evaluation and assurance. The focus of this work was in assurance, which means to verify one’s own work. There are 34 metrics available for security measurements, of which five are evaluation metrics and 29 are assurance metrics. We found, however, that the general quality of these metrics was not good. Only three metrics in the design category passed the inspection criteria and could be used in the case study. The metrics claim to give quantitative information on the security of the software, but in practice they were limited to evaluating different versions of the same software. Apart from being relative, the metrics were unable to detect security issues or point out problems in the design. Furthermore, interpreting the metrics’ results was difficult. In conclusion, the general state of the software security metrics leaves a lot to be desired. The metrics studied had both theoretical and practical issues, and are not suitable for daily engineering workflows. The metrics studied provided a basis for further research, since they pointed out areas where the security metrics were necessary to improve whether verification of security from the design was desired.

Development and Effect Analysis of the Asteri Consultative Auditing Process - Safety and Security Management in Educational Institutions

The Finnish legislation requires for a safe and secure learning environment. However, the comprehensive, risk based safety and security management (SSM) and the management commitment in the implementation and development of the SSM are not mentioned in the legislation. Multiple institutions, operators and researchers have studied and developed safety and security in educational institutions over the past decade. Typically the approach has been fragmented and without bringing up the importance of the comprehensive SSM. The development needs of the safety and security operations in universities have been studied. However, in universities of applied sciences (UASs) and in elementary schools (ESs), the performance level, strengths and weaknesses of the comprehensive SSM have not been studied. The objective of this study was to develop the comprehensive, risk based SSM of educational institutions by developing the new Asteri consultative auditing process and study its effects on auditees. Furthermore, the performance level in the comprehensive SSM in UASs and ESs were studied using Asteri and the TUTOR model developed by the Keski-Uusimaa Department for Rescue Services. In addition, strengths, development needs and differences were identified. In total, 76 educational institutions were audited between the years 2011 and 2014. The study is based on logical empiricism, and an observational applied research design was used. Auditing, observation and an electronic survey were used for data collection. Statistical analysis was used to analyze the collected information. In addition, thematic analysis was used to analyze the development areas of the organizations mentioned by the respondents in the survey. As one of the main contributions, this research presents the new Asteri consultative auditing process. Organizations with low performance levels on the audited subject benefit the most from the Asteri consultative auditing process. Asteri may be usable in many different types of audits, not only in SSM audits. As a new result, this study provides new knowledge on attitudes related to auditing. According to the research findings, auditing may generate negative attitudes and the auditor should take them into account when planning and preparing for audits. Negative attitudes can be compensated by producing added value, objectivity and positivity for the audit and, thus, improve the positive effects of auditing on knowledge and skills. Moreover, as the results of this study shows, auditing safety and security issues do not increase feelings of insecurity, but rather increase feelings of safety and security when using the new Asteri consultative auditing process with the TUTOR model. The results showed that the SSM in the audited UASs was statistically significantly more advanced than that in the audited ESs. However, there is still room for improvement in the ESs and the UASs as the approach to the SSM was fragmented. It can be assumed that the majority of Finnish UASs and ESs do not likely meet the basic level of the comprehensive, risk based the SSM.

Assessing development and the idea of development in the 1950s in Brazil

The decade of 1950s was a crucial period of the industrialization of the Brazilian economy. The dominant school of thought was the national-developmentalism, which was not restricted to the sphere of economic production but also encompassed political and socio-cultural processes of change. Combining repression, persuasion and paternalism, the national state took a significantly political and economic responsibility in the social, material and symbolic modernization during the Vargas and Kubitschek administrations. However, internal disputes, foreign demands and a long legacy of socio-spatial inequalities prevented the achievement of more socially inclusive goals, leading a legacy of unanswered questions that still have currency today.

Effect of loading type on the fatigue strength of symmetric and asymmetric welded joints made of ultra high strength steel

In this study, finite element analyses and experimental tests are carried out in order to investigate the effect of loading type and symmetry on the fatigue strength of three different non-load carrying welded joints. The current codes and recommendations do not give explicit instructions how to consider degree of bending in loading and the effect of symmetry in the fatigue assessment of welded joints. The fatigue assessment is done by using effective notch stress method and linear elastic fracture mechanics. Transverse attachment and cover plate joints are analyzed by using 2D plane strain element models in FEMAP/NxNastran and Franc2D software and longitudinal gusset case is analyzed by using solid element models in Abaqus and Abaqus/XFEM software. By means of the evaluated effective notch stress range and stress intensity factor range, the nominal fatigue strength is assessed. Experimental tests consist of the fatigue tests of transverse attachment joints with total amount of 12 specimens. In the tests, the effect of both loading type and symmetry on the fatigue strength is studied. Finite element analyses showed that the fatigue strength of asymmetric joint is higher in tensile loading and the fatigue strength of symmetric joint is higher in bending loading in terms of nominal and hot spot stress methods. Linear elastic fracture mechanics indicated that bending reduces stress intensity factors when the crack size is relatively large since the normal stress decreases at the crack tip due to the stress gradient. Under tensile loading, experimental tests corresponded with finite element analyzes. Still, the fatigue tested joints subjected to bending showed the bending increased the fatigue strength of non-load carrying welded joints and the fatigue test results did not fully agree with the fatigue assessment. According to the results, it can be concluded that in tensile loading, the symmetry of joint distinctly affects on the fatigue strength. The fatigue life assessment of bending loaded joints is challenging since it depends on whether the crack initiation or propagation is predominant.

Abrasion, transport and distribution of sediment in selected streams of Southern Ontario and Western New York /

The rate of decrease in mean sediment size and weight per square metre along a 54 km reach of the Credit River was found to depend on variations in the channel geometry. The distribution of a specific sediment size consist of: (1) a transport zone; (2) an accumulation zone; and (3) a depletion zone. These zones shift downstream in response to downcurrent decreases in stream competence. Along a .285 km man-made pond, within the Credit River study area, the sediment is also characterized by downstream shifting accumulation zones for each finer clast size. The discharge required to initiate movement of 8 cm and 6 cm blocks in Cazenovia Creek is closely approximated by Baker and Ritter's equation. Incipient motion of blocks in Twenty Mile Creek is best predicted by Yalin's relation which is more efficient in deeper flows. The transport distance of blocks in both streams depends on channel roughness and geometry. Natural abrasion and distribution of clasts may depend on the size of the surrounding sediment and variations in flow competence. The cumulative percent weight loss with distance of laboratory abraded dolostone is defined by a power function. The decrease in weight of dolostone follows a negative exponential. In the abrasion mill, chipping causes the high initial weight loss of dolostone; crushing and grinding produce most of the subsequent weight loss. Clast size was found to have little effect on the abrasion of dolostone within the diameter range considered. Increasing the speed of the mill increased the initial amount of weight loss but decreased the rate of abrasion. The abrasion mill was found to produce more weight loss than stream action. The maximum percent weight loss determined from laboratory and field abrasion data is approximately 40 percent of the weight loss observed along the Credit River. Selective sorting of sediment explains the remaining percentage, not accounted for by abrasion.

Genesis and distribution of Mississippi Valley-type ore assemblages in Middle Silurian strata, Niagara Peninsula, Ontario /

Presently non-commercial occurrences of Mississippi Valley-type ore assemblages in the Middle Silurian strata of the Niagara Peninsula have been studied. Based on this detailed study, a new poly-stage genetic model is proposed which relates ore mineralization in carbonate environments to the evolution of the sedimentary basin. Sulphide ore mineralization occurred during two episodes: 1. During the late diagenesis stage, which is characterized by compaction-maturation of the sediments, the initial mineralization took place by upward and outward movement of connate waters. Metals were probably supplied from all the sediments regardless of their specific lithologies. However, clay minerals were possibly the main contributors. The possible source of sulphur was from petroleum-type hydrocarbons presently mixed with the sediments at the site of ore deposition. Evidence for this is the fact that the greatest abundance of ore minerals is in petroliferous carbonates. The hydrocarbons probably represent liquids remaining after upward migration to the overlying Guelph-Salina reservoirs. The majority of sphalerite and galena formed during this period, as well as accessory pyrite, marcasite, chalcopyrite, chalcocite, arsenopyrite, and pyrrhotite; and secondary dolomite, calcite, celestite, and gypsum. 2. During the presently ongoing surface erosion and weathering phase, which is marked by the downward movement of groundwater, preexisting sulphides were probably remobilized, and trace amounts of lead and zinc were leached from the host material, by groundwaters. Metal sulphides precipitated at, or below, the water table, or where atmospheric oxygen could raise the Eh of groundwaters to the point where soluble metal complexes are unstable and native sulphur co-precipitates with sphalerite and galena. This process, which can be observed today, also results in the transport and deposition of the host rock material. Breakdown of pre-existing sulphide and sulphate, as well as hydrocarbon present in the host rock, provided sulphur necessary for sulphide precipitation. The galena and sphalerite are accompanied by dolomite, calcite, gypsum, anglesite, native sulphur and possibly zincite.

A social-cognitive model of monitoring and its relationship to behaviour in a naturalistic observation : development and individual differences

years 8 months) and 24 older (M == 7 years 4 months) children. A Monitoring Process Model (MPM) was developed and tested in order to ascertain at which component process ofthe MPM age differences would emerge. The MPM had four components: (1) assessment; (2) evaluation; (3) planning; and (4) behavioural control. The MPM was assessed directly using a referential communication task in which the children were asked to make a series of five Lego buildings (a baseline condition and one building for each MPM component). Children listened to instructions from one experimenter while a second experimenter in the room (a confederate) intetjected varying levels ofverbal feedback in order to assist the children and control the component ofthe MPM. This design allowed us to determine at which "stage" ofprocessing children would most likely have difficulty monitoring themselves in this social-cognitive task. Developmental differences were obselVed for the evaluation, planning and behavioural control components suggesting that older children were able to be more successful with the more explicit metacomponents. Interestingly, however, there was no age difference in terms ofLego task success in the baseline condition suggesting that without the intelVention ofthe confederate younger children monitored the task about as well as older children. This pattern ofresults indicates that the younger children were disrupted by the feedback rather than helped. On the other hand, the older children were able to incorporate the feedback offered by the confederate into a plan ofaction. Another aim ofthis study was to assess similar processing components to those investigated by the MPM Lego task in a more naturalistic observation. Together the use ofthe Lego Task ( a social cognitive task) and the naturalistic social interaction allowed for the appraisal of cross-domain continuities and discontinuities in monitoring behaviours. In this vein, analyses were undertaken in order to ascertain whether or not successful performance in the MPM Lego Task would predict cross-domain competence in the more naturalistic social interchange. Indeed, success in the two latter components ofthe MPM (planning and behavioural control) was related to overall competence in the naturalistic task. However, this cross-domain prediction was not evident for all levels ofthe naturalistic interchange suggesting that the nature ofthe feedback a child receives is an important determinant ofresponse competency. Individual difference measures reflecting the children's general cognitive capacity (Working Memory and Digit Span) and verbal ability (vocabulary) were also taken in an effort to account for more variance in the prediction oftask success. However, these individual difference measures did not serve to enhance the prediction oftask performance in either the Lego Task or the naturalistic task. Similarly, parental responses to questionnaires pertaining to their child's temperament and social experience also failed to increase prediction oftask performance. On-line measures ofthe children's engagement, positive affect and anxiety also failed to predict competence ratings.

Studies on oxamyl : analytical method development and investigation of fate in peach seedlings and corn seeds

A high performance liquid chromatographic method employing two columns connected in series and separated~y·a.switching valve has been developed for the analysis of the insecticide/ nematicide oxamyl (methyl-N' ,N'-dimethyl-N-[(methylcarbamoyl) oxy]-l-thiooxarnimidate) and two of its metabolites. A variation of this method involving two reverse phase columns was employed to monitor the persistence and translocation of oxamyl in treated peach seedlings. It was possible to simultaneously analyse for oxamyl and its corresponding oxime (methyl-N',N'-dimethyl-N-hydroxy-l-thiooxamimidate}, a major metabolite of oxamyl in plants, without prior cleanup of the samples. The method allowed detection of 0.058 pg oxamyl and 0.035 p.g oxime. On treated peach leaves oxamyl was found to dissipate rapidly during the first two-week period, followed by a period of slow decomposition. Movement of oxamyl or its oxime did not occur in detectable quantities to untreated leaves or to the root or soil. A second variation of the method which employed a size exclusion column as·the first column and a reverse phase column as the second was used to monitor the degradation of oxamyl in treated, planted corn seeds and was suitable for simultaneous analysis of oxamyl, its oxime and dimethylcyanoformamide (DMCF), a metabolite of oxamyl. The method allowed detection of 0.02 pg oxamyl, 0.02 p.g oxime and 0.005 pg DMCF. Oxamyl was found to persist for a period of 5 - 6 weeks, which is long enough to permit oxamyl seedtreatment to be considered as a potential means of protecting young corn plants from nematode attack. Decomposition was found to be more rapid in unsterilized soil than in sterililized soil. DMCF was found to have a nematostatic effect at high concentrations ( 2,OOOpprn), but at lower concentrations no effect on nematode mobility was observed. Oxamyl, on the other hand, was found to reduce the mobility of nematodes at concentrations down to 4 ppm.

The effect of social skills training on grade 3 students' self-esteem, moral development and perceptions of classroom environment

Two Grade 3 classes were used to study the effects of a formal social skills training program. Specifically, comparisons were made on self-esteem, classroom environment, and moral development to see whether changes occurred as a direct result of social skills training. One group participated in the social skills program, while the other group did not. It was hypothesized that formal social skills training would improve students' selfesteem, moral development, and the classroom environment. At the end of the program, however, data from class observations, teacher interviews, journal of the social skills training group teacher, and measures of self-esteem, classroom environment and moral development did not support this hypothesis. Although the social skills training group scored significantly higher in class cohesiveness, they did not show marked improvement in the other measures. In fact, in some measures (e.g., friction and competitiveness), they demonstrated greater scores at both pretest and posttests. The social skills training group was, however, able to vocalize and utilize the strategies of several skills which had been a focus of the program, suggesting that formal social skills training is a useful tool for presenting and reinforcing some specific behaviours.