Innovative Leak Test for Pavement Joint Seals, Progress Report, HR-318, 1993

Premature failure of concrete pavement contraction joint seals is an ongoing and costly problem for the Iowa Department of Transportation. Several joint seal test sections consisting of variations in sawing methods, joint cleaning techniques, sealant installation, and sealant types have been established over the past few years. Laboratory analysis and field inspections were done as a part of the tests, and core samples were taken for laboratory adhesion pull tests. Such methods often cover specifically small areas and may not expose hidden failures. Some tests are also labor-intensive and destructive, especially that of coring. An innovative, nondestructive, broad coverage joint seal tester that yields quick results has been designed and developed for evaluation of pavement joint seal performance. The Iowa vacuum joint seal tester (IA-VAC) applies a low vacuum above a joint seal that has been spray-covered with a foaming water solution. Any unsealed area or leak that exists along the joint will become quickly and clearly visible by the development of bubbles at the leak point. By analyzing the results from the IA-VAC tests, information on the number and types of leaks can be obtained; such information will help identify the source of the problem and direct efforts toward a solution.

Longitudinal Joint Forming in PCC Pavements, MLR-00-05, Construction Report, 2003

In conventional construction practices, a longitudinal joint is sawed in a PCC (Portland Cement Concrete) pavement to control concrete shrinkage cracking between two lanes of traffic. Sawing a joint in hardened concrete is an expensive and time consuming operation. The longitudinal joint is not a working joint (in comparison to a transverse joint) as it is typically tied with a tie bar at 30 inch spacing. The open joint reservoir, left by the saw blade, typically is filled or sealed with a durable crack sealant to keep incompressibles and water from getting into the joint reservoir. An experimental joint forming knife has been developed. It is installed under the paving machine to form the longitudinal joint in the wet concrete as a part of the paving process. Through this research method, forming a very narrow longitudinal joint during the paving process, two conventional paving operations can be eliminated. Joint forming eliminates the need of the joint sawing operation in the hard concrete, and as the joint that is formed does not leave a wide-open reservoir, but only a hairline crack, it does not need the joint filling or sealing operation. Therefore, the two conventional longitudinal joint sawing and sealing operations are both being eliminated by this innovation. A laboratory scale prototype joint forming knife was built and tested, initially forming joints in small concrete beams. The results were positive so the method was proposed for field testing. Initial field tests were done in the construction season of 2001, limited to one paving contractor. A number of modifications were made to the knife throughout the field tests. About 3000 feet of longitudinal joint was formed in 2001. Additional testing was done in the 2002 construction season, working with the same contractor. About 150,000 feet of longitudinal joint was formed in 2002. Evaluations of the formed joints were done to determine longitudinal joint hairline crack development rate and appearance. Additional tests will be done in the next construction season to improve or perfect the longitudinal joint forming technique.

Demonstration and Field Evaluation of Alternative Portland Cement Concrete Pavement Reinforcement Materials, Construction Report, HR-1069, 1998

The function of dowel bars is the transfer of a load across the transverse joint from one pavement slab to the adjoining slab. In the past, these transfer mechanisms have been made of steel. However, pavement damage such as loss of bonding, deterioration, hollowing, cracking and spalling start to occur when the dowels begin to corrode. A significant amount of research has been done to evaluate alternative types of materials for use in the reinforcement of concrete pavements. Initial findings have indicated that stainless steel and fiber composite materials possess properties, such as flexural strength and corrosion resistance, that are equivalent to the Department of Transportation specifications for standard steel, 1 1/2 inch diameter dowel bars. Several factors affect the load transfer of dowels; these include diameter, alignment, grouting, bonding, spacing, corrosion resistance, joint spacing, slab thickness and dowel embedment length. This research is directed at the analysis of load transfer based on material type and dowel spacing. Specifically, this research is directed at analyzing the load transfer characteristics of: (a) 8-inch verses 12-inch spacing, and (b) alternative dowel material compared to epoxy coated steel dowels, will also be analyzed. This report documents the installation of the test sections, placed in 1997. Dowel material type and location are identified. Construction observations and limitations with each dowel material are shown.

Towards a dynamic model of e-commerce: environmental, technological and organisational drivers of B2C along time

Despite the important benefits for firms of commercial initiatives on the Internet, e-commerce is still an emerging distribution channel, even in developed countries. Thus, more needs to be known about the mechanisms affecting its development. A large number of works have studied firms¿ e-commerce adoption from technological, intraorganizational, institutional, or other specific perspectives, but there is a need for adequately tested integrative frameworks. Hence, this work proposes and tests a model of firms¿ business-to-consumer (called B2C) e-commerce adoption that is founded on a holistic vision of the phenomenon. With this integrative approach, the authors analyze the joint influence of environmental, technological, and organizational factors; moreover, they evaluate this effect over time. Using various representative Spanish data sets covering the period 1996-2005, the findings demonstrate the suitability of the holistic framework. Likewise, some lessons are learned from the analysis of the key building blocks. In particular, the current study provides evidence for the debate about the effect of competitive pressure, since the findings show that competitive pressure disincentivizes e-commerce adoption in the long term. The results also show that the development or enrichment of the consumers¿ consumption patterns, the technological readiness of the market forces, the firm¿s global scope, and its competences in innovation continuously favor e-commerce adoption.

6.2

Airborne particles can come from a variety of sources and contain variable chemical constituents. Some particles are formed by natural processes, such as volcanoes, erosion, sea spray, and forest fires, while other are formed by anthropogenic processes, such as industrial- and motor vehicle-related combustion, road-related wear, and mining. In general, larger particles (those greater than 2.5 μm) are formed by mechanical processes, while those less than 2.5 μm are formed by combustion processes. The chemical composition of particles is highly influenced by the source: for combustion-related particles, factors such as temperature of combustion, fuel type, and presence of oxygen or other gases can also have a large impact on PM composition. These differences can often be observed at a regional level, such as the greater sulphate-composition of PM in regions that burn coal for electricity production (which contains sulphur) versus regions that do not. Most countries maintain air monitoring networks, and studies based on the resulting data are the most common basis for epidemiology studies on the health effects of PM. Data from these monitoring stations can be used to evaluate the relationship between community-level exposure to ambient particles and health outcomes (i.e., morbidity or mortality from various causes). Respiratory and cardiovascular outcomes are the most commonly assessed, although studies have also considered other related specific outcomes such as diabetes and congenital heart disease. The data on particle characteristics is usually not very detailed and most often includes some combination of PM2.5, PM10, sulphate, and NO2. Other descriptors that are less commonly found include particle number (ultrafine particles), metal components of PM, local traffic intensity, and EC/OC. Measures of association are usually reported per 10 μg/m3 or interquartile range increase in pollutant concentration. As the exposure data are taken from regional monitoring stations, the measurements are not representative of an individual's exposure. Particle size is an important descriptor for understanding where in the human respiratory system the particles will deposit: as a general rule, smaller particles penetrate to deeper regions of the lungs. Initial studies on the health effects of particulate matter focused on mass of the particles, including either all particles (often termed total suspended particulate or TSP) or PM10 (all particles with an aerodynamic diameter less than 10 μm). More recently, studies have considered both PM10 and PM2.5, with the latter corresponding more directly to combustion-related processes. UFPs are a dominant source of particles in terms of PNC, yet are negligible in terms of mass. Very few epidemiology studies have measured the effect of UFPs on health; however, the numbers of studies on this topic are increasing. In addition to size, chemical composition is of importance when understanding the toxicity of particles. Some studies consider the composition of particles in addition to mass; however this is not common, in part due the cost and labour involved in such analyses.

Suurnopeuskuvaustekniikan soveltaminen hitsausvalokaaren tutkimuksessa

Työn tavoitteena oli suurnopeuskuvaustekniikan ottaminen osaksi Kemppi Oy:n tuotekehitystä. Työn teoriaosa sisältää hitsausvalokaaren ja lisäaineensiirtymisen teoriaa,sekä perehtymisen suurnopeuskuvaustekniikkaan ja siihen vaadittaviin laitteistoihin. Teoriassa tarkastellaan myös MIG/MAG -päittäisliitoksen olemassa oleviin pohjapalon hitsausprosesseihin. Kokeellisen osan tuloksena syntyi suurnopeuskuvaustekniikkaan pohjautuva tutkimusmenetelmä. Rakennetulla järjestelmällä nähtiin hyvin teoriassa esitetyt MIG/MAG -hitsauksen kaarityypit ja lisäaineensiirtymisen muodot. Kuvattuja tuloksia kyettiin analysoimaan ja vertaamaan teoriaan. Päittäisliitoksen pohjapalon hitsaukseen soveltuvan prosessin kehitys oli osa käytännön osuutta. Tehdyillä kuvauksilla onnistuttiin havainnoimaan kehitetyn valokaaren ja aineensiirtymisen ilmiöitä. Näiden ymmärtäminen helpottui kuvauksien ansiosta ja tämä nopeutti ja mahdollisti tuotekehitystyötä. Tuloksena valmistui uusi pulssitettu lyhytkaariprosessi. Työn tuloksena syntyi uusi suurnopeuskuvaustekniikkaan nojautuva tuotekehitysprosessi, jossa uusi tekniikka kyetään liittämäänosaksi tutkimus- ja kehitystyötä. Tuloksia voidaan käyttää myös markkinoinnin ja myynnin edistämiseen.

Small proline-rich protein 1A is a gp130 pathway- and stress-inducible cardioprotective protein.

The interleukin-6 cytokines, acting via gp130 receptor pathways, play a pivotal role in the reduction of cardiac injury induced by mechanical stress or ischemia and in promoting subsequent adaptive remodeling of the heart. We have now identified the small proline-rich repeat proteins (SPRR) 1A and 2A as downstream targets of gp130 signaling that are strongly induced in cardiomyocytes responding to biomechanical/ischemic stress. Upregulation of SPRR1A and 2A was markedly reduced in the gp130 cardiomyocyte-restricted knockout mice. In cardiomyocytes, MEK1/2 inhibitors prevented SPRR1A upregulation by gp130 cytokines. Furthermore, binding of NF-IL6 (C/EBPbeta) and c-Jun to the SPRR1A promoter was observed after CT-1 stimulation. Histological analysis revealed that SPRR1A induction after mechanical stress of pressure overload was restricted to myocytes surrounding piecemeal necrotic lesions. A similar expression pattern was found in postinfarcted rat hearts. Both in vitro and in vivo ectopic overexpression of SPRR1A protected cardiomyocytes against ischemic injury. Thus, this study identifies SPRR1A as a novel stress-inducible downstream mediator of gp130 cytokines in cardiomyocytes and documents its cardioprotective effect against ischemic stress.

Value added logistics in supply and demand chains. Smile. Part 1. eBusiness between global company and itslocal sme supplier network

VALOSADE (Value Added Logistics in Supply and Demand Chains) is the research project of Anita Lukka's VALORE (Value Added Logistics Research) research team inLappeenranta University of Technology. VALOSADE is included in ELO (Ebusiness logistics) technology program of Tekes (Finnish Technology Agency). SMILE (SME-sector, Internet applications and Logistical Efficiency) is one of four subprojects of VALOSADE. SMILE research focuses on case network that is composed of small and medium sized mechanical maintenance service providers and global wood processing customers. Basic principle of SMILE study is communication and ebusiness insupply and demand network. This first phase of research concentrates on creating backgrounds for SMILE study and for ebusiness solutions of maintenance case network. The focus is on general trends of ebusiness in supply chains and networksof different industries; total ebusiness system architecture of company networks; ebusiness strategy of company network; information value chain; different factors, which influence on ebusiness solution of company network; and the correlation between ebusiness and competitive advantage. Literature, interviews and benchmarking were used as research methods in this qualitative case study. Networks and end-to-end supply chains are the organizational structures, which can add value for end customer. Information is one of the key factors in these decentralized structures. Because of decentralization of business, information is produced and used in different companies and in different information systems. Information refinement services are needed to manage information flows in company networksbetween different systems. Furthermore, some new solutions like network information systems are utilised in optimising network performance and in standardizingnetwork common processes. Some cases have however indicated, that utilization of ebusiness in decentralized business model is not always a necessity, but value-add of ICT must be defined case-specifically. In the theory part of report, different ebusiness and architecture models are introduced. These models are compared to empirical case data in research results. The biggest difference between theory and empirical data is that models are mainly developed for large-scale companies - not for SMEs. This is due to that implemented network ebusiness solutions are mainly large company centered. Genuine SME network centred ebusiness models are quite rare, and the study in that area has been few in number. Business relationships between customer and their SME suppliers are nowadays concentrated more on collaborative tactical and strategic initiatives besides transaction based operational initiatives. However, ebusiness systems are further mainly based on exchange of operational transactional data. Collaborative ebusiness solutions are in planning or pilot phase in most case companies. Furthermore, many ebusiness solutions are nowadays between two participants, but network and end-to-end supply chain transparency and information systems are quite rare. Transaction volumes, data formats, the types of exchanged information, information criticality,type and duration of business relationship, internal information systems of partners, processes and operation models (e.g. different ordering models) differ among network companies, and furthermore companies are at different stages on networking and ebusiness readiness. Because of former factors, different customer-supplier combinations in network must utilise totally different ebusiness architectures, technologies, systems and standards.

Value added logistics in supply and demand chain. Smile. Part 2. eBusiness in a service business. Case: A maintenance and operations network in forest industry

VVALOSADE is a research project of professor Anita Lukka's VALORE research team in the Lappeenranta University of Technology. The VALOSADE includes the ELO technology program of Tekes. SMILE is one of four subprojects of the VALOSADE. The SMILE study focuses on the case of the company network that is composed of small and micro-sized mechanical maintenance service providers and forest industry as large-scale customers. The basic principle of the SMILE study is the communication and ebusiness in supply and demand networks. The aim of the study is to develop ebusiness strategy, ebusiness model and e-processes among the SME local service providers, and onthe other hand, between the local service provider network and the forest industry customers in a maintenance and operations service business. A literature review, interviews and benchmarking are used as research methods in this qualitative case study. The first SMILE report, 'Ebusiness between Global Company and Its Local SME Supplier Network', concentrated on creating background for the SMILE study by studying general trends of ebusiness in supply chains and networks of different industries. This second phase of the study concentrates on case network background, such as business relationships, information systems and business objectives; core processes in maintenance and operations service network; development needs in communication among the network participants; and ICT solutions to respond needs in changing environment. In the theory part of the report, different ebusiness models and frameworks are introduced. Those models and frameworks are compared to empirical case data. From that analysis of the empirical data, therecommendations for the development of the network information system are derived. In process industry such as the forest industry, it is crucial to achieve a high level of operational efficiency and reliability, which sets up great requirements for maintenance and operations. Therefore, partnerships or strategic alliances are needed between the network participants. In partnerships and alliances, deep communication is important, and therefore the information systems in the network also are critical. Communication, coordination and collaboration will increase in the case network in the future, because network resources must be optimised to improve competitive capability of the forest industry customers and theefficiency of their service providers. At present, ebusiness systems are not usual in this maintenance network. A network information system among the forest industry customers and their local service providers actually is the only genuinenetwork information system in this total network. However, the utilisation of that system has been quite insignificant. The current system does not add value enough either to the customers or to the local service providers. At present, thenetwork information system is the infomediary that share static information forthe network partners. The network information system should be the transaction intermediary, which integrates internal processes of the network companies; the network information system, which provides common standardised processes for thelocal service providers; and the infomediary, which share static and dynamic information on right time, on right partner, on right costs, on right format and on right quality. This study provides recommendations how to develop this system in the future to add value to the network companies. Ebusiness scenarios, vision, objectives, strategies, application architecture, ebusiness model, core processes and development strategy must be considered when the network information system will be developed in the next development step. The core processes in the case network are demand/capacity management, customer/supplier relationship management, service delivery management, knowledge management and cash flow management. Most benefits from ebusiness solutions come from the electrifying of operational level processes, such as service delivery management and cash flow management.

Investigation of interaction between native and impurity defects in ZnSe

Zinc selenide is a prospective material for optoelectronics. The fabrication of ZnSe­based light-emitting diodes is hindered by complexity of p-type doping of the component materials. The interaction between native and impurity defects, the tendency of doping impurity to form associative centres with native defects and the tendency to self-compensation are the main factors impeding effective control of the value and type of conductivity. The thesis is devoted to the study of the processes of interaction between native and impurity defects in zinc selenide. It is established that the Au impurity has the most prominent amphoteric properties in ZnSe among Cu, Ag and Au impurities, as it forms a great number of both Au; donors and Auz„ acceptors. Electrical measurements show that Ag and Au ions introduced into vacant sites of the Zn sublattice form simple single-charged Agz„+ and Auzn+ states with d1° electron configuration, while Cu ions can form both single-charged Cuz„ (d1) and double-charged Cuzr`+ (d`o) centres. Amphoteric properties of Ag and Au transition metals stimulated by time are found for the first time from both electrical and luminescent measurements. A model that explains the changes in electrical and luminescent parameters by displacement of Ag ions into interstitial sites due to lattice deformation forces is proposed. Formation of an Ag;-donor impurity band in ZnSe samples doped with Ag and stored at room temperature is also studied. Thus, the properties of the doped samples are modified due to large lattice relaxation during aging. This fact should be taken into account in optoelectronic applications of doped ZnSe and related compounds.

Short-term HIIT and Fatmax training increase aerobic and metabolic fitness in men with class II and III obesity.

OBJECTIVE: To compare the effects of two different 2-week-long training modalities [continuous at the intensity eliciting the maximal fat oxidation (Fatmax ) versus high-intensity interval training (HIIT)] in men with class II and III obesity. METHODS: Nineteen men with obesity (BMI ≥ 35 kg(.) m(-2) ) were assigned to Fatmax group (GFatmax ) or to HIIT group (GHIIT ). Both groups performed eight cycling sessions matched for mechanical work. Aerobic fitness and fat oxidation rates (FORs) during exercise were assessed prior and following the training. Blood samples were drawn to determine hormones and plasma metabolites levels. Insulin resistance was assessed by the homeostasis model assessment of insulin resistance (HOMA2-IR). RESULTS: Aerobic fitness and FORs during exercise were significantly increased in both groups after training (P ≤ 0.001). HOMA2-IR was significantly reduced only for GFatmax (P ≤ 0.001). Resting non-esterified fatty acids (NEFA) and insulin decreased significantly only in GFatmax (P ≤ 0.002). CONCLUSIONS: Two weeks of HIIT and Fatmax training are effective for the improvement of aerobic fitness and FORs during exercise in these classes of obesity. The decreased levels of resting NEFA only in GFatmax may be involved in the decreased insulin resistance only in this group.

Fiber-reinforced Composite as Oral Implant Material. Experimental studies of glass fiber and bioactive glass in vitro and in vivo

Fiber-reinforced composite as oral implant material: Experimental studies of glass fiber and bioactive glass in vitro and in vivo Department of Prosthetic Dentistry and Biomaterials Science, Institute of Dentistry, University of Turku, Turku, Finland 2008. Biocompatibility and mechanical properties are important variables that need to be determined when new materials are considered for medical implants. Special emphasis was placed on these characteristics in the present work, which aimed to investigate the potential of fiber-reinforced composite (FRC) material as an oral implant. Furthermore, the purpose of this study was to explore the effect of bioactive glass (BAG) on osseointegration of FRC implants. The biocompatibility and mechanical properties of FRC implants were studied both in vitro and in vivo. The mechanical properties of the bulk FRC implant were tested with a cantilever bending test, torsional test and push-out test. The biocompatibility was first evaluated with osteoblast cells cultured on FRC substrates. Bone bonding was determined with the mechanical push-out test and histological as well as histomorplanimetric evaluation. Implant surface was characterized with SEM and EDS analysis. The results of these studies showed that FRC implants can withstand the static load values comparably to titanium. Threaded FRC implants had significantly higher push-out strength than the threaded titanium implants. Cell culture study revealed no cytotoxic effect of FRC materials on the osteoblast-like-cells. Addition of BAG particles enhanced cell proliferation and mineralization of the FRC substrates The in vivo study showed that FRC implants can withstand static loading until failure without fracture. The results also suggest that the FRC implant is biocompatible in bone. The biological behavior of FRC was comparable to that of titanium after 4 and 12 weeks of implantation. Furthermore, addition of BAG to FRC implant increases peri-implant osteogenesis and bone maturation.

Optimal slopes and speeds in uphill ski mountaineering: a laboratory study.

The purpose of this study was to estimate the energy cost of linear (EC) and vertical displacement (ECvert), mechanical efficiency and main stride parameters during simulated ski mountaineering at different speeds and gradients, to identify an optimal speed and gradient that maximizes performance. 12 subjects roller skied on a treadmill at three different inclines (10, 17 and 24 %) at three different speeds (approximately 70, 80 and 85 % of estimated peak heart rate). Energy expenditure was calculated by indirect calorimetry, while biomechanical parameters were measured with an inertial sensor-based system. At 10 % there was no significant change with speed in EC, ECvert and mechanical efficiency. At 17 and 24 % the fastest speed was significantly more economical. There was a significant effect of gradient on EC, ECvert and mechanical efficiency. The most economical gradient was the steepest one. There was a significant increase of stride frequency with speed. At steep gradients only, relative thrust phase duration decreased significantly, while stride length increased significantly with speed. There was a significant effect of gradient on stride length (decrease with steepness) and relative thrust phase duration (increase with steepness). A combination of a decreased relative thrust phase duration with increased stride length and frequency decreases ECvert. To minimize the energy expenditure to reach the top of a mountain and to optimize performance, ski-mountaineers should choose a steep gradient (~24 %) and, provided they possess sufficient metabolic scope, combine it with a fast speed (~6 km h(-1)).

The interaction between mercury(II) and sulfathiazole

The interaction of mercury(II) with sulfathiazole has been analyzed. IR and NMR spectral studies suggest a coordination of Hg(II) with the Nthiazolic atom, unlike related Hg-sulfadrugs compounds. The complex was screened for its activity against Escherichia coli, showing an appreciable antimicrobial activity compared with the ligand.

Caracterização de amostras comerciais de vermicomposto de esterco bovino e avaliação da influência do pH e do tempo na adsorção de Co(II), Zn(II) and Cu(II)

Some commercial samples of vermicompost from bovine manure (humus) were characterized by thermogravimetry with respect to humidity, organic matter and ash contents, the percentages of which range from 6.55 to 5.35%, 53.01 to 69.96% and 46.44 to 66,14%, respectively. The capacity of adsorption of Cu2+, Zn2+ and Co2+ ions by these samples has been evaluated as a function of pH and time. The contents of several metal ions in the original vermicompost samples have been determined by flame atomic absorption spectrometry after digestion in a microwave oven. The high nitrogen content suggests that the earthworms used in the maturation procedure lead to an efficient degradation of organic matter. The metal retention was affected by both pH and adsorption time. The results also show that adsorption follows the order Cu2+ > Zn2+ > Co2+.